Search Results

Search found 3315 results on 133 pages for 'magic packet'.

Page 89/133 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

  • WSUS KB978338 Chain of Supersession Incorrect?

    - by Kasius
    The chain appears to be KB978338 to KB978886 to KB2563894 to KB2588516 (newest). All four of these updates are approved on our WSUS server. KB978338 is listing as Not Applicable on all machines, because it has been superseded. This is the behavior I would expect. However, our security office is reporting that KB978338 should still be installed on all machines because its actual effect is not replicated by any of the updates that follow it. Here is the analysis I was sent: KB978886 applies to Vista SP1 only. The rollout of SP2 did not address the ISATAP vulnerability and reintroduces it. KB2563894 only updates two files (Tcpip.sys and Tcpipreg.sys). It does not update the 12 other affected ISATAP, UDP, and NUD .sys and .dll files. (MS11-064) KB2588516 addresses malformed continuous UDP packet overflow. But does not address the ISATAP related NUD and TCP .sys and .dll files. (MS11-083) So yes, many IP vulnerabilities. But each KB addresses specific issues that do not cross over to other KBs. We can install KB978338 by manually running the .MSU file, but we aren't certain if that will overwrite the couple files that get updated by later patches since we would be installing the patch out of order. Is the above analysis correct? Is the chain of supersession incorrectly defined? If it is, what is the proper way to report it so that it can be changed by the correct Microsoft team? We are currently using 32-bit and 64-bit installations of Vista SP2. Note: I should mention that I posted this on Technet as well. I will keep this up-to-date with any information I get on there.

    Read the article

  • PowerConnect 3548p SNTP and web interface not working

    - by Force Flow
    I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

    Read the article

  • SDCC and malloc() - allocating much less memory than is available

    - by Duncan Bayne
    When I run compile this code with SDCC 3.1.0, and run it on an Amstrad CPC 464 (under emulation, with WinCPC 0.9.26 running on Wine): void _test_malloc() { long idx = 0; while (1) { if (malloc(5)) { printf("%ld\r\n", ++idx); } else { printf("done"); break; } } } ... it consistently taps out at 92 malloc()s. I make that 460 bytes, which leads me to a couple of questions: What is malloc() doing on this system? I was sort of hoping for an order of magnitude more storage even on a 64kB system The behaviour is consistent on 64kB systems and 128kB systems; do I have to perform some sort of magic to access the additional memory, like manual bank switching?

    Read the article

  • Is it possible to have an out-of-process COM server where a separate O/S process is used for each ob

    - by Tom Williams
    I have a legacy C++ "solution engine" that I have already wrapped as an in-process COM object for use by client applications that only require a single "solution engine". However I now have a client application that requires multiple "solution engines". Unfortunately the underlying legacy code has enough global data, singletons and threading horrors that given available resources it isn't possible to have multiple instances of it in-process simultaneously. What I am hoping is that some kind soul can tell me of some COM magic where with the flip of a couple of registry settings it is possible to have a separate out-of-process COM server (separate operating system process) for each instance of the COM object requested. Am I in luck?

    Read the article

  • Simplest DNS solution for remote offices

    - by dunxd
    I look after a bunch of remote offices that connect via VPN - a Cisco ASA 5505 in each office acts as Firewall and VPN end point. Beyond that we keep things as simple as possible in the offices to minimise the support burden. We don't have any kind of server except in offices large enough to justify having someone dedicated to IT. Basically there is the ASA, some computers, a network printer and a switch. One of the problems I am seeing in a lot of offices is that DNS requests looking up hosts inside our network often fail - I'm assuming timeouts due to the offices internet connection (they are all in developing world countries) having some sub-optimal qualities (e.g. high latency caused by VSAT segments, or packet loss. The obvious solution to this is to have some sort of local DNS service that can serve local requests - so I think it would need to do zone transfers from our Microsoft Windows 2008 R2 DNS servers at HQ. However, simply installing Windows Servers in each office is both expensive, and creates a support burden. This got me thinking about pfsense/m0n0wall on embedded devices - those can act as a DNS server, and could be configured at HQ and sent out as just something that needs to be plugged into the network and can then be forgotten about by the staff locally. Maybe there are some alternatives to the ASA 5505 that include some DNS functionality. Has anyone here dealt with the problem, either using some kind of embedded device, or found some other solution? Any gotchas or reasons to avoid what I have suggested?

    Read the article

  • create_or_update in ModelForm

    - by ykaganovich
    I want to have a ModelForm that can create_or_update a model instance based on the request parameters. I've been trying to cobble something together, but am realizing that my python fu is not strong enough, and the ModelForm implementation code is a quite hairy. I found this create_or_update snipplet for working with a Model, but I think it would be incredibly useful if it were integrated with a ModelForm. I would expect it to behave similarly to ModelForm.save(): class BetterModelForm(forms.ModelForm): def init(self, *args, **kwargs) def create_or_update(self): #magic return (instance, created, updated) Conversely I'd also be interested in hearing compelling reasons why this is not a good idea.

    Read the article

  • Laptop Randomly Turning On and Off

    - by Ian Mallett
    So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

    Read the article

  • Tortoisesvn not showing up correct status after commit

    - by Michael
    Hi, I was going to ask this in tigris.org, however they have maintenance in their forum. My environment: Windows 7 x64, Tortoisesvn latest x64, simple repo. What I'm doing: I am adding a new file to repo, then doing SVN Commit. This operation is successful and I can see it in repo from trac or directly. I expect: To see that file's icon as green checkmark. What I have: I see blue PLUS icon, like I haven't done commit. However, if I just create any new file in that folder(without any commit or update), the icon is immediately changing to checkmark. What a magic! I don't expect here anyone to have answer, this might be a bug, but who knows )) Cheers!

    Read the article

  • [Flex 4] Removing sort arrows from AdvancedDataGridColumn Header.

    - by zeroDivisible
    Hello, I am doing this simple project using Flex 4 SDK and I got stuck with this simple problem: I have turned sortable property for AdvancedDataGridColumn to false, but the column header is still rendered as: As You can see, my label for this header is "06", but the column header is divided and it keeps the place for sort arrow. How can I change this? I would like my column header to contain only my label. I know that most probably I need to do some magic with AdvancedDataGridHeaderRenderer but I just started learning Flex and would like to receive some help. Thank You for help. Best regards, Mike.

    Read the article

  • Dependency Injection with @Inject in Weld (JSR-299 RI). How is the corresponding @Produces found?

    - by Thorbjørn Ravn Andersen
    I have played with the JSR-299 Reference Implementation "Weld" with the purpose of using it in a stand-alone application, and I have had a look at the documentation, and marveled at the magic. My question is how the producer of a given object to be @Inject'ed is found? Either the java compiler produces hints for annotations which is easily found by the classloader, or the complete classpath must be traversed loading all classes to see what they do which sounds highly inefficient to me, or it is a completely different approach. What is the trick?

    Read the article

  • java runtime tracing library to replace system.out.println

    - by Grzegorz Oledzki
    Have you heard of any library which would allow me to set up a tracing for specific methods at runtime? Instead of adding (and removing) lots of System.out.println in my code (and having to re-compile and re-deploy) I would like to have a magic thing which would print out a line for each call of selected method without any change in the code. This would work without re-compiling, so some kind of JVM agent (or some non-standard JVM would be needed?). Sounds like a job for aspect programming? A typical scenario would be to start an application, configure the traced methods dynamically (in a separate file or similar) and then everytime a selected method is called a line with its name (and arguments) is printed out to System.out (or some log file). Naturally one could think of tens of additional features, but this basic set would be a great tool. BTW, I use Eclipse interactive debugger too, not only the System.out tracing technique, but both have some advantages and sometimes Eclipse is not enough.

    Read the article

  • How does jQuery .data() work?

    - by kazanaki
    My Javascript knowledge is pretty limited. Instead of asking several javascript questions I got the "message" from Stack overflow and started using jQuery right away in order to save me some time. However several times I do not undestand the "magic" behind jQuery and I would love to learn the details. I want to use .data() in my application. The examples are very helpful. I do not understand however WHERE these values are stored. I inspect the webpage with Firebug and as soon as .data() saves an object to a dom element, I do not see any change in Firebug (either HTML or Dom tabs). I tried to look at jQuery source, but it is very advanced for my Javascript knowledge and I lost myself. So the question is: Where do the values stored by jQuery.data() actually go? Can I inspect/locate/list/debug them using a tool?

    Read the article

  • Does Displaytag stash the "media type" in a page or request attribute?

    - by Pointy
    When you enable "export" from Displaytag, the tag code gives you links with special magic parameters that the tag recognizes as indicators that the table contents should be exported (as CSV, Excel, whatever). Well I'm interested in detecting the media type so that (for example) I can exclude columns that make no sense in an export (embedded action buttons, for one thing, or checkboxes for row selection). I suppose I could write a table decorator and use that to stick the media type on the request, but it'd be nice to avoid that if the tag already does it. The documentation is not clear on the subject; I guess I can start digging through the source code too.

    Read the article

  • Linq to Entities, checking for specific foreign key id?

    - by AaronLS
    I am trying to get rows where the foreign key ParentID == 0, and this is what I am trying but I get a NotSupportedException because it can't translate the ArrayIndex [0]: IQueryable<ApplicationSectionNode> topLevelNodeQuery = from n in uacEntitiesContext.ApplicationSectionNodeSet where (int)n.Parent.EntityKey.EntityKeyValues[0].Value == 0 orderby n.Sequence select n; So I need to pull that ArrayIndex out of the query so that the runtime can successfully translate the query. I'm not sure how to do that though. How does one query a specific object via it's primary key or set of objects via foreign key? Edit: Note that there is not actually a row in the table with NodeId == 0, the 0 is a magic value(not my idea) to indicate top level nodes. So I can't do n.Parent.NodeId == 0

    Read the article

  • Hyper-V with multiple physical networks

    - by Yaman
    I have Hyper-V on my laptop with a wireless and Ethernet card, sometimes I connect using wireless card, and sometimes using the Ethernet cable. I am trying to configure Hyper-v to work always with internet provided to virtual machine. I have tried to create 2 virtual switches, one external to the Wireless network card, and the other one external to the Ethernet card. What happens is that the wireless network creates a bridge object in the network and sharing center\Network connections of windows 8, while the Ethernet does not. Unfortunately, they do not work together as external, i have to set the connected one to external and the other one as external, I also have to go to the properties of the bridge and virtual Ethernet properties to uncheck and check some components like: Client for Microsoft Networks Deterministic Network Enhancer VMWare Bridge Protocol QoS Packet Scheduler File and Printer Sharing for Microsoft Networks In order to make things work. Sometimes I keep the wireless network switch external, and go to another location (another wireless network), and it disconnects, i have to reconfigure the switches. Is there a way to do the configuration once and remain working wherever I connect, whether its Wireless or Ethernet and on any network with DHCP?

    Read the article

  • Connecting Java se Client to Glassfish

    - by Henrik Bierbum Bacher
    We are having some difficulties connecting our Java SE standalone client with the EJB module deployed on a remote GlassFish server. Pointers to how we are supposed to connect our client would be appreciated. The client code we currently has to get the initial context: props.setProperty("org.omg.CORBA.ORBInitialHost", "*remotehost*"); props.setProperty("org.omg.CORBA.ORBInitialPort", "portNumber"); javax.naming.InitialContext ic = new javax.naming.InitialContext(props); *We have tried several different port numbers; 3700, 7676, 8080.. The closest we are getting, got us the error: "Error in GIOP magic". I read that jms are using port 7676 as a broker port for a bunch of dynamically generated ports, but can't figure out how to specify those ports in order to create proper port-forwards.

    Read the article

  • In Jenkins, how to checkout a project into a specific directory (using GIT)

    - by viebel
    Sorry for the 'svn' style - we are in a process of migration from SVN to GIT (including our CI Jenkins environment). What do we need is to be able to make Jenkins to checkout (or should I say clone?) the GIT project (repository?) into a specific directory. We've tried some refspecs magic but it wasn't to obvious to understand and to use successfully. Furthermore, if in the same Jenkins project we need to checkout several private GitHub repositories into several separate dirs under a project root. How can we do it please? We have GitHub plugin installed. Hope we've phrased the things right.

    Read the article

  • Configure static IPv6 on Ubuntu

    - by Charles Offenbacher
    I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

    Read the article

  • FTP Server with advanced features

    - by Nikolas Sakic
    Hi, We supply zone-files to our customers. Some zone files are big about 300MB and some are quite small, maybe like 1MB. We had this issue that someone setup a script to continually download the file. Imagine downloading 300MB file a few hundred times a day. Since, we don't have packet-shaper to throttle the traffic, we need to upgrade ftp server and use add-on modules to limit the download somehow. We currently use proftpd server. Also note that there are different users for different domains - say, if you want to download zone file for .INFO domain, then you use a particular user. That user can't download any other zone's file. This is what we are looking for: Have maximum of 400MB download per user per day. Or even have different download limit for different users per day. Have one connection per user at any time. Max # of connection (non-simultaneous) per user per day is 5. Anyone trying to exceed that gets banned for 24 hours. Has anyone used FTP server with similar restrictions above? Does anyone have any ideas where I can start? Any help would be appreciated. Thanks. -N

    Read the article

  • tc u32 --- how to match L2 protocols in recent kernels?

    - by brownian
    I have a nice shaper, with hashed filtering, built at a linux bridge. In short, br0 connects external and internal physical interfaces, VLAN tagged packets are bridged "transparently" (I mean, no VLAN interfaces are there). Now, different kernels do it differently. I can be wrong with exact kernel verions ranges, please forgive me. Thanks. 2.6.26 So, in debian, 2.6.26 and up (up to 2.6.32, I believe) --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 Here, "kernel" matches two bytes in "protocol" field with 0x8100, but counts the beginning of ip packet as a "zero position" (sorry for my English, if I'm a bit unclear). 2.6.32 Again, in debian (I've not built vanilla kernel), 2.6.32-5 --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 at 20 flowid 1:200 Here, "kernel" matches the same for protocol, but counts offset from the beginning of this protocol's header --- I have to add 4 bytes to offset (20, not 16 for dst address). It's ok, seems more logical, as for me. 3.2.11, the latest stable now This works --- as if there is no 802.1q tag at all: tc filter add dev internal protocol ip parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 The problem is that I couldn't find a way to match 802.1q tag so far. Matching 802.1q tag at past I could do this before as follows: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 match u16 0x0ed8 0x0fff at -4 flowid 1:300 Now I'm unable to match 802.1q tag with at 0, at -2, at -4, at -6 or like that. The main issue that I have zero hits count --- this filter is not being checked at all, "wrong protocol", in other words. Please, anyone, help me :-) Thanks!

    Read the article

  • Keepalived for more than 20 virtual addresses

    - by cvaldemar
    I have set up keepalived on two Debian machines for high availability, but I've run into the maximum number of virtual IP's I can assign to my vrrp_instance. How would I go about configuring and failing over 20+ virtual IP's? This is the, very simple, setup: LB01: 10.200.85.1 LB02: 10.200.85.2 Virtual IPs: 10.200.85.100 - 10.200.85.200 Each machine is also running Apache (later Nginx) binding on the virtual IPs for SSL client certificate termination and proxying to backend webservers. The reason I need so many VIP's is the inability to use VirtualHost on HTTPS. This is my keepalived.conf: vrrp_script chk_apache2 { script "killall -0 apache2" interval 2 weight 2 } vrrp_instance VI_1 { interface eth0 state MASTER virtual_router_id 51 priority 101 virtual_ipaddress { 10.200.85.100 . . all the way to . 10.200.85.200 } An identical configuration is on the BACKUP machine, and it's working fine, but only up to the 20th IP. I have found a HOWTO discussing this problem. Basically, they suggest having just one VIP and routing all traffic "via" this one IP, and "all will be well". Is this a good approach? I'm running pfSense firewalls in front of the machines. Quote from the above link: ip route add $VNET/N via $VIP or route add $VNET netmask w.x.y.z gw $VIP Thanks in advance. EDIT: @David Schwartz said it would make sense to add a route, so I tried adding a static route to the pfSense firewall, but that didn't work as I expected it would. pfSense route: Interface: LAN Destination network: 10.200.85.200/32 (virtual IP) Gateway: 10.200.85.100 (floating virtual IP) Description: Route to VIP .100 I also made sure I had packet forwarding enabled on my hosts: $ cat /etc/sysctl.conf net.ipv4.ip_forward=1 net.ipv4.ip_nonlocal_bind=1 Am I doing this wrong? I also removed all VIPs from the keepalived.conf so it only fails over 10.200.85.100.

    Read the article

  • Return database messages on successful SQL execution when using ADO

    - by peacedog
    I'm working on a legacy VB6 app here at work, and it has been a long time since I've looked at VB6 or ADO. One thing the app does is to executes SQL Tasks and then to output the success/failure into an XML file. If there is an error it inserts the text the task node. What I have been asked to do is try and do the same with the other mundane messages that result from succesfully executed tasks, like (323 row(s) affected). There is no command object being used, it's just an ADODB.Connection object. Here is the gist of the code: Dim sqlStatement As String Set sqlStatement = /* sql for task */ Dim sqlConn As ADODB.Connection Set sqlConn = /* connection magic */ sqlConn.Execute sqlStatement, , adExecuteNoRecords What is the best way for me to capture the non-error messages so I can output them? Or is it even possible?

    Read the article

  • Formula needed: Sort Array

    - by aw
    I have the following array: a = [1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16] I use it for some visual stuff like this: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Now I want to sort the array like this: 1 3 6 10 2 5 9 13 4 8 12 15 7 11 14 16 //So the original array should look like this: a = [1,5,2,9,6,3,13,10,7,4,14,11,8,15,12,16] Yeah, now I'm looking for a smart formula to do that ticker = 0; originalArray = [1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16] newArray = []; while(ticker < originalArray.length) { //do the magic here ticker++; }

    Read the article

  • Routing / binding 128 IPs to one server

    - by Andrew
    I have a Ubuntu server with 128 ip's (static external ips 86.xx.xx.16), and I want to crawl pages thru different ip's. The gateway is xx.xxx.xxx.1, the main ip is xx.xxx.xxx.16, and the other 128 ip's are xx.xxx.xxx.129/255. I tried this configuration in /etc/network/interfaces but I doesn't work. It work if I remove the gateway for the aliases eth0:0 and eth0:1. I think this is routing problem. auto lo iface lo inet loopback auto eth0 auto eth0:0 auto eth0:1 iface eth0 inet static address xx.xxx.xxx.16 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:0 inet static address xx.xxx.xxx.129 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:1 inet static address xx.xxx.xxx.130 netmask 255.255.255.128 gateway xx.xxx.xxx.1 Also, please tell me how to "reset" every changes that I made in networking and routing. Update: I removed the gateway and now it works. I can reach the website thru all 128 ip's. But when I try to bind a socket connection in php to a specific ip I get no answer. socket_bind($sock, "xx.xxx.xx.xxx"); socket_connect($sock, 'google.com', 80); I tryed to use a sniffer to see the packets, and I see the packet sent from binded ip to google.com but the "connection" can't be established. I don't know anything about "route" command, but I have a feeling that this is the solution.

    Read the article

  • linux routing issue

    - by Duc To
    Hi! I have 2 linksys routers which has linux running on it and using tomato firmware.. both has internet lines plugged on but only 1 acts as DHCP server (router 1) What I am having to achieve is that all packets goes to router 1 from internal IPs want to access internet will go out to that internet line but from 1 specific port, if router 1 detects packets from a specific source port (for ex: http port: 80), it will redirect that packet to router 2 and goes out to the internet from there.. I have found some documents which give solution that I will need a linux servers with 2 ethernet cards and then we plug both internet lines on that server and routing base on it but I do not want to do that because my boss does not want to have an extra work mantaining that server, besides, he says that the router itself already a linux one so why.. I tend to agree his points.. Can it be done or a seperate linux server acting as a router is a must? Thank you all in advance and really look forward in your replies.. I am newbie to linux network and it seems to be something out of my capacity to solve :( Your sincerely! Duc To

    Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >