Search Results

Search found 27946 results on 1118 pages for 'output buffer empty'.

Page 895/1118 | < Previous Page | 891 892 893 894 895 896 897 898 899 900 901 902  | Next Page >

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• How can I recover XFS partitions from a formatted HD?

  - by giuprivite

  I deleted the partition table of my HD. I wanted to format another one, but by mistake, I formatted the wrong one. Then I also created some new partition on it. Now I would like, if possible, to recover my old data. The old configuration was this: A primary NTFS partition with Windows, and a secondary partition with four logical partitions: a swap and three XFS partitions (two for Ubuntu and OpenSuSE, and one with the home for both systems). This is the output I get when I run gpart in a terminal: ubuntu@ubuntu:~$ sudo gpart /dev/sdb Begin scan... Possible partition(Windows NT/W2K FS), size(39997mb), offset(0mb) Possible extended partition at offset(39997mb) Possible partition(Linux swap), size(8189mb), offset(39997mb) Possible partition(SGI XFS filesystem), size(40942mb), offset(48187mb) Possible partition(SGI XFS filesystem), size(40942mb), offset(89149mb) Possible partition(SGI XFS filesystem), size(175044mb), offset(130112mb) End scan. Checking partitions... Partition(OS/2 HPFS, NTFS, QNX or Advanced UNIX): primary Partition(Linux swap or Solaris/x86): logical Partition(Linux ext2 filesystem): logical Partition(Linux ext2 filesystem): orphaned logical Partition(Linux ext2 filesystem): orphaned logical Ok. Guessed primary partition table: Primary partition(1) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) size: 39997mb #s(81915360) s(63-81915422) chs: (0/1/1)-(1023/254/63)d (0/1/1)-(5098/254/51)r Primary partition(2) type: 015(0x0F)(Extended DOS, LBA) size: 265245mb #s(543221849) s(81915435-625137283) chs: (1023/254/63)-(1023/254/63)d (5099/0/1)-(38912/254/2)r Primary partition(3) type: 000(0x00)(unused) size: 0mb #s(0) s(0-0) chs: (0/0/0)-(0/0/0)d (0/0/0)-(0/0/0)r Primary partition(4) type: 000(0x00)(unused) size: 0mb #s(0) s(0-0) chs: (0/0/0)-(0/0/0)d (0/0/0)-(0/0/0)r Looking the first eight lines, it seems the data are still there... but I don't know how to recover them. I have a free second HD of about 500 GB (the formatted one is 320 GB) that I can use for the recovery process.

  Read the article

• Installing Ruby 1.9.3 OSX 10.7.4 breaks after altering PATH

  - by R V

  I was having trouble installing ruby 1.9.3-p194 from ruby 1.8.7 on my mac osx 10.7.4. I have was trying to fix my homebrew after running "brew doctor" and got the message of "/usr/bin occurs before /usr/local/bin This means that system-provided programs will be used instead of those provided by Homebrew. The following tools exist at both paths: c++-4.2 cpp-4.2 erb g++-4.2 gcc-4.2 gcov-4.2 gem i686-apple-darwin11-cpp-4.2.1 i686-apple-darwin11-g++-4.2.1 i686-apple-darwin11-gcc-4.2.1 irb rake rdoc ri ruby testrb" I fixed it by entering the following, which I found on another stackoverflow answer: export PATH="/usr/local/bin:/usr/local/sbin:~/bin$PATH" Lo and behold! when I typed that ruby updates to 1.9.3-p194. Ruby files seem to compile and run just fine. However, afterward, my navigation around terminal is messed up severely. For instance I can't do the command "open example_file.html" and have the file pop up in Chrome, instead I get the error: "-bash: open: command not found" Also, when I change directory, I get an error, inputting "$ cd desktop" yields the output, "-bash: dirname: command not found" but the directory does then changes... strange. When I exit out of a terminal window all this resets. I'm back to Ruby 1.8.7, have to use the PATH command again to update to 1.9.3, command line navigation gets broken again. Any guidance on how to remedy so I can use 1.9.3-p194 and also have normal terminal navigation would be greatly appreciated.

  Read the article

• /etc/security/limits.conf for setting program limits in Linux

  - by Flavius Akerele

  I have the following inside /etc/security/limits.conf (I have specified root separately because * will not include it.) user2 - core unlimited * - core 0 root - core 0 * - rss 512000 root - rss 512000 * - nproc 100 root - nproc 100 * - maxlogins 1 root - maxlogins 1 I run a program as user2 (./programname) but /proc/3498/limits says cores are disabled: Limit Soft Limit Hard Limit Units Max cpu time unlimited unlimited seconds Max file size unlimited unlimited bytes Max data size unlimited unlimited bytes Max stack size 8388608 unlimited bytes Max core file size 0 0 bytes Max resident set 524288000 524288000 bytes Max processes 100 100 processes Max open files 1024 1024 files Max locked memory 65536 65536 bytes Max address space unlimited unlimited bytes Max file locks unlimited unlimited locks Max pending signals 14001 14001 signals Max msgqueue size 819200 819200 bytes Max nice priority 0 0 Max realtime priority 0 0 Max realtime timeout unlimited unlimited us Both ulimit -Sa and ulimit -Ha output that cores are disabled: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 14001 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) 512000 open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) unlimited cpu time (seconds, -t) unlimited max user processes (-u) 100 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Why are cores disabled ?

  Read the article

• Surprising corruption and never-ending fsck after resizing a filesystem.

  - by Steve Kemp

  System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

  Read the article

• File system concepts (df command)

  - by mkab

  I'm finding it difficult to understand some stuffs about the df command. Suppose I type df and I have the following output Filesystem 1k-blocks Used Avail Capacity Mounted on /dev/da0s1 some number some number number percentage /win /dev/da0s2 some number some number number percentage /win/home /dev/da0s3a some number some number number percentage / devfs some number some number number percentage /dev /dev/da0s3g some number some number number percentage /local /dev/da0s3h some number some number -number 102% /reste /dev/da0s3d some number some number number percentage /tmp /dev/da1s3f some number some number number percentage /usr /dev/da1s3e some number some number number percentage /var /dev/da1s1a some number some number number percentage /public Are the answers to the following questions correct? How many physical drives do I have? Ans: 2. da0s1 and da1s1 How many physical partitions on each disk? Ans: 8 for da0s1 and 1 for da1s1 How many BSD partition on each physical partition Ans: Impossible to determine. We have to use the -T to determine its type How is it possible for the file system /dev/da0s3h filled at 102%? And where is this overflowed data written?Ans: I have no idea for this one Thanks.

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• Starting nginx with systemctl fails, but running the command manually doesn't

  - by Ivan

  On Arch Linux, for some reason, when I try to start nginx with the command "systemctl start nginx", it fails, with this being the output of "systemctl status nginx": Loaded: loaded (/etc/systemd/system/nginx.service; enabled) Active: failed (Result: exit-code) since Wed 2013-10-30 16:22:17 EDT; 5s ago Process: 9835 ExecStop=/usr/bin/chroot --userspec=http:http /home/nginx /usr/bin/nginx -g pid /run/nginx.pid; -s quit (code=exited, status=126) Process: 3982 ExecStart=/usr/bin/chroot --userspec=http:http /home/nginx /usr/bin/nginx -g pid /run/nginx.pid; daemon on; master_process on; (code=exited, status=0/SUCCESS) Process: 10967 ExecStartPre=/usr/bin/chroot --userspec=http:http /home/nginx /usr/bin/nginx -t -q -g pid /run/nginx.pid; daemon on; master_process on; (code=exited, status=126) Main PID: 3984 (code=exited, status=0/SUCCESS) CGroup: /system.slice/nginx.service ...but when I run /usr/bin/chroot --userspec=http:http /home/nginx /usr/bin/nginx -t -q -g "pid /run/nginx.pid; daemon on; master_process on;" and then /usr/bin/chroot --userspec=http:http /home/nginx /usr/bin/nginx -g "pid /run/nginx.pid; daemon on; master_process on;" as root, all it does is return a warning, but works just fine: nginx: [warn] the "user" directive makes sense only if the master process runs with super-user privileges, ignored in /etc/nginx/nginx.conf:1 Why is it doing that?

  Read the article

• probems using ssh from cron

  - by Travis

  I am attempting to automate a script that executes commands on remote machines via ssh. I have public key authentication setup between the machines using ssh-agent. The script runs fine when executed from the command prompt. I suspect my problem is that cron isn't starting the ssh-agent due to it's minimalist environment. Here is the output when I add the -v flag to ssh: debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering public key: /home/<user>/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 149 debug1: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> debug1: Trying private key: /home/<user>/.ssh/id_dsa debug1: Next authentication method: password debug1: Authentications that can continue: publickey,gssapi-with-mic,password Permission denied, please try again. debug1: Authentications that can continue: publickey,gssapi-with-mic,password Permission denied, please try again. debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: No more authentication methods to try. Permission denied (publickey,gssapi-with-mic,password). How can I make this work? Thanks!

  Read the article

• OpenLDAP with StartTLS broken on Debian Lenny

  - by mr.zog

  I'm trying to get OpenLDAP on Lenny to work with StartTLS. I have a Fedora 13 machine which I'm using as a client for testing. So far the Fedora client is ignoring the 'host' directive in /etc/ldap.conf when I try to connect using ldapsearch. The client wants to connect to 127.0.0.1:389 even if I specify -H ldaps://server.name on when using ldapsearch. /etc/ldap.conf on the client machine is in mode 444. But even when I try connecting locally from an ssh session, I see errors like this: ldap_sasl_interactive_bind_s: Can't contact LDAP server (-1) Someone hit me with a cluebat, plz. Update: you must use ~/.ldaprc for settings such as 'host'. Also, I just used nmap against the ldap server and it showed 636 and 389 in an open state. Here's what prints to screen when I try to connect with, ldapsearch -ZZ –x '(objectclass=*)'+ -d -1 ldap_create ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 192.168.10.41:636 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 192.168.10.41:636 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdb8 end=0x9bdbdd7 len=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ber_scanf fmt ({) ber: ber_dump: buf=0x9bdbdb8 ptr=0x9bdbdbd end=0x9bdbdd7 len=26 0000: 77 18 80 16 31 2e 33 2e 36 2e 31 2e 34 2e 31 2e w...1.3.6.1.4.1. 0010: 31 34 36 36 2e 32 30 30 33 37 1466.20037 ber_flush2: 31 bytes to sd 3 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_write: want=31, written=31 0000: 30 1d 02 01 01 77 18 80 16 31 2e 33 2e 36 2e 31 0....w...1.3.6.1 0010: 2e 34 2e 31 2e 31 34 36 36 2e 32 30 30 33 37 .4.1.1466.20037 ldap_result ld 0x9bd3050 msgid 1 wait4msg ld 0x9bd3050 msgid 1 (infinite timeout) wait4msg continue ld 0x9bd3050 msgid 1 all 1 ** ld 0x9bd3050 Connections: * host: 192.168.10.41 port: 636 (default) refcnt: 2 status: Connected last used: Sun Jun 6 12:54:05 2010 ** ld 0x9bd3050 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x9bd3050 request count 1 (abandoned 0) ** ld 0x9bd3050 Response Queue: Empty ld 0x9bd3050 response count 0 ldap_chkResponseList ld 0x9bd3050 msgid 1 all 1 ldap_chkResponseList returns ld 0x9bd3050 NULL ldap_int_select read1msg: ld 0x9bd3050 msgid 1 all 1 ber_get_next ldap_read: want=8, got=0 ber_get_next failed. ldap_err2string ldap_start_tls: Can't contact LDAP server (-1)

  Read the article

• Azure's Ubuntu 12.0.4 fails to install PHP5

  - by Alex Kennberg

  Similar to this article from Azure themselves: http://www.windowsazure.com/en-us/manage/linux/common-tasks/install-lamp-stack/ I am trying to install PHP5 on Ubuntu 12.0.4 virtual machine. However, it fails installing the ssl-cert. $ sudo apt-get install php5 Reading package lists... Done Building dependency tree Reading state information... Done php5 is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 49 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up ssl-cert (1.0.28) ... Could not create certificate. Openssl output was: Generating a 2048 bit RSA private key ............................+++ ...................................................................................................................+++ writing new private key to '/etc/ssl/private/ssl-cert-snakeoil.key' ----- problems making Certificate Request 140320238503584:error:0D07A097:asn1 encoding routines:ASN1_mbstring_ncopy:string too long:a_mbstr.c:154:maxsize=64 dpkg: error processing ssl-cert (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: ssl-cert E: Sub-process /usr/bin/dpkg returned an error code (1) Any tips appreciated.

  Read the article

• VirtualBox communication from Linux to/from Windows 7

  - by J. Otto Tennant

  VirtualBox is running in Windows 7 as the host. VirtualBox has the two modifications (one is called Guest Additions; don't remember the other). The Virtual machine has "bridged" networking selected. I have SAMBA set up (now, the problem may be here; it has been three or four years since I last did this) on the Linux guest machine. Neither guest nor host sees the other. From the Windows 7 command prompt, the IP address of the Linux guest pings. The IP address of another computer (a separate Windows 7 on the wireless network) pings from the Linux guest. (I have no idea what IP address the Windows 7 host itself has. The output of "netstat" does not seem to be useful.) So, it seem to me that something should be working. The only workgroup on the LAN is inventively named WORKGROUP. SMB4K should be seeing something. There must be a simple setup step that I am missing. (FWIW, there are two processes running smbd, and no process is running nmbd. YaST says that nmbd is set to run. I am not sure what this means.)

  Read the article

• CPU / Affinity mask problem in SQL 2005

  - by Robert Moir

  Hi folks, Having a problem with a SQL Server which was virtualised. The CPU mask was set on the physical host for some reason and now advanced options are not available. So I need to reconfigure the CPU affinity mask settings - which are advanced options, so this is blocked because of the affinity mask issue. I've tried doing this from the SQL server in single user command line mode, I've googled and found lots of people with similar problems but no real solution. I'm stumped. Any ideas? Sample commands and output from query analyser below. sp_configure 'show advanced options', 1 GO RECONFIGURE WITH OVERRIDE GO sp_configure 'affinity mask', 0x00000000 GO RECONFIGURE GO ----------------------------------------- Configuration option 'show advanced options' changed from 0 to 1. Run the RECONFIGURE statement to install. Msg 5832, Level 16, State 1, Line 1 The affinity mask specified does not match the CPU mask on this system. Msg 15123, Level 16, State 1, Procedure sp_configure, Line 51 The configuration option 'affinity mask' does not exist, or it may be an advanced option.

  Read the article

• ssh connection operation timed out using rsync

  - by Mark Molina

  I use rsync to backup my remote server on my local device but when I combine it with a cron job my ssh times out. Just to be clear, the data is stored on a remote server and I want it stored on my local server. The backup request must be sent from my local server to the remote server. The command for backup up the data is working when I just type it in terminal like this: rsync -chavzP --stats USERNAME@IPADDRES: PATH_TO_BACKUP LOCAL_PATH_TO_BACKUP but when I combine it with a cron job like this: 10 11 * * * rsync -chavzP --stats USERNAME@IP_ADDRESS: PATH_TO_BACKUP LOCAL_PATH_TO_BACKUP the ssh connection times out. When the cronjob executes it send a mail to the root user with the output like this: From local.xx.xx.xx Tue Jul 2 11:20:17 2013 X-Original-To: username Delivered-To: [email protected] From: [email protected] (Cron Daemon) To: [email protected] Subject: Cron <username@server> rsync -chavzP --stats USERNAME@IPADDRES: PATH_TO_BACKUP LOCAL_PATH_TO_BACKUP X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <PATH=/usr/bin:/bin> X-Cron-Env: <LOGNAME=username> X-Cron-Env: <USER=username> X-Cron-Env: <HOME=/Users/username> Date: Tue, 2 Jul 2013 11:20:17 +0200 (CEST) ssh: connect to host IP_ADDRESS port XX: Operation timed out rsync: connection unexpectedly closed (0 bytes received so far) [receiver] rsync error: unexplained error (code 255) at /SourceCache/rsync/rsync-42/rsync/io.c(452) [receiver=2.6.9] So the rsync command is working when just typed in terminal but not when used by a cronjob. Can anybody explain this?

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• Mac OS X - configuring ntpd server with on LAN with D-Link DIR-655

  - by Mark C

  Hey all, This question is pretty specific, but I hope someone will have seen this error elsewhere. I a configuring a machine running OS X 10.5.8 to be an NTP server for machines connected to a LAN that is not connected to the Internet. I am not too worried about knowing the "right" time on all the machines, but rather worried about making sure everyone has the same notion of time. I configured the NTP daemon on Mac by turning on the Set date and time automatically in System Preferences, using the server's clock, 127.127.1.0 as the reference clock. I figured I should see if the server can NTP query itself before proceeding to the clients. The weird part is when I run the ntpq -p command in a command-prompt when connected to my D-Link DIR-655 (firmware: 1.33), it hangs for about a minute or so each time before finally giving me some output. I thought the problem might have to do with Port Forwarding, so I configured the router to forward port 123 for the IP of the server, but that did not improve the situation. When I run the ntpq -p command on my school's network, on a Linksys WRT54G router, or with the wireless Airport card turned off - I have absolutely no problems - the command returns a response instantly. Is this normal? I can see why a query might take a minute or so, but I don't understand why one router does it faster than the other. I tried messing around with the ntp.conf file adding the burst, minpoll, and maxpoll options: server 127.127.1.0 burst minpoll 4 maxpoll 5 Figuring that perhaps I am polling too often and the configuration file is slowing me down, but even with this, the ntpq still hangs on the D-Link DIR-655, but does just fine on the other routers. Any thoughts on where the lag is coming from or if the lag is even a problem?

  Read the article

• Puppet Decentralized Setup

  - by paul.tw

  I want to migrate my existing Puppet setup from master/client to a decentralized solution. I know other solutions, such as Ansible are easier to setup for that purpose, but I really want to stay with Puppet. I found "supply_drop"(https://github.com/pitluga/supply_drop) on github, so I followed the instructions and did the following: rvm gemset create testing rvm use 1.9.3@testing gem install supply_drop The output is the following: [m@ms-MacBook-Pro:~ $ irb 1.9.3-p547 :001 require 'supply_drop' NameError: uninitialized constant Capistrano from /Users/m/.rvm/gems/ruby-1.9.3-p547@testing/gems/supply_drop-0.17.0/lib/supply_drop/tasks.rb:1:in `' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:55:in `require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:55:in `require' from /Users/m/.rvm/gems/ruby-1.9.3-p547@testing/gems/supply_drop-0.17.0/lib/supply_drop.rb:10:in `' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:135:in `require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:135:in `rescue in require' from /Users/m/.rvm/rubies/ruby-1.9.3-p547/lib/ruby/site_ruby/1.9.1/rubygems/core_ext/kernel_require.rb:144:in `require' from (irb):1 from /Users/m/.rvm/rubies/ruby-1.9.3-p547/bin/irb:12:in `' Since that doesn't work without problems, I was wondering which alternatives are there available to do the same. Do you have any suggestings?

  Read the article

• Cannot access firewalled jboss server from Internet Explorer

  - by Simon Gibbs

  I've produced a website for a client One Single Menu using JBoss and hosted it on Rackspace Cloud Servers running Ubuntu's Maverick Meerkat. Following advice, I esablished some iptables rule to protect jboss: iptables -I INPUT 1 -i lo -j ACCEPT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-port 8080 iptables -I INPUT -p tcp --dport 8080 -j ACCEPT iptables -t nat -A OUTPUT -o lo -p tcp --dport 80 -j REDIRECT --to-port 8080 iptables -A INPUT -j DROP Now, several versions of IE on several computers on at least two different ISPs cannot access the onesinglemenu.com. Curl from within the datacenter, Firefox, and Safari on the same ISPs can all access the server fine. I even tried IE and Firefox on the same computer and IE failed but Firefox worked. The error behaviour is that IE hangs on connecting without reporting an error, even after a minute or so. No page is displayed at all. I find it quite odd that I'm having a browser specific connection issue, but it appears to be the case. Help!

  Read the article

• Add static route through DHCP

  - by MathieuK

  I'm trying to get an OSX Lion Server to provide a static route to its clients (all OSX Lion) over DHCP. I can't get the client to actually apply the static route. So far, I've managed to get the DHCP server (BOOTPD) to actually serve the DHCP OPTION 33 (static_route) on the DHCP offers by editing /etc/bootpd.plist and adding something like: <key>dhcp_option_33</key> <data>[some base64 goes here]</data> .. and restarting the DHCP service. On the client I've managed to get the client to actually request the dhcp option by modifying and adding option 33 to the DHCPRequestedParameterList key: <key>DHCPRequestedParameterList</key> <array> ... keys snipped for brevity ... <integer>33</integer> </array> .. and rebooting the client. This makes the client request the static_route option from the DHCP server ( i can see the proper output in ipconfig getpacket en0 ) but it doesn't actually apply the rule. Has anyone ever succeeded in applying static_route options on OSX clients through DHCP?

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• Recovering a damaged microSDHC

  - by djechelon

  I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

  Read the article

• How can I recover XFS partitions from a formatted HD?

  - by giuprivite

  I deleted the partition table of my HD. I wanted to format another one, but by mistake, I formatted the wrong one. Then I also created some new partition on it. Now I would like, if possible, to recover my old data. The old configuration was this: A primary NTFS partition with Windows, and a secondary partition with four logical partitions: a swap and three XFS partitions (two for Ubuntu and OpenSuSE, and one with the home for both systems). This is the output I get when I run gpart in a terminal: ubuntu@ubuntu:~$ sudo gpart /dev/sdb Begin scan... Possible partition(Windows NT/W2K FS), size(39997mb), offset(0mb) Possible extended partition at offset(39997mb) Possible partition(Linux swap), size(8189mb), offset(39997mb) Possible partition(SGI XFS filesystem), size(40942mb), offset(48187mb) Possible partition(SGI XFS filesystem), size(40942mb), offset(89149mb) Possible partition(SGI XFS filesystem), size(175044mb), offset(130112mb) End scan. Checking partitions... Partition(OS/2 HPFS, NTFS, QNX or Advanced UNIX): primary Partition(Linux swap or Solaris/x86): logical Partition(Linux ext2 filesystem): logical Partition(Linux ext2 filesystem): orphaned logical Partition(Linux ext2 filesystem): orphaned logical Ok. Guessed primary partition table: Primary partition(1) type: 007(0x07)(OS/2 HPFS, NTFS, QNX or Advanced UNIX) size: 39997mb #s(81915360) s(63-81915422) chs: (0/1/1)-(1023/254/63)d (0/1/1)-(5098/254/51)r Primary partition(2) type: 015(0x0F)(Extended DOS, LBA) size: 265245mb #s(543221849) s(81915435-625137283) chs: (1023/254/63)-(1023/254/63)d (5099/0/1)-(38912/254/2)r Primary partition(3) type: 000(0x00)(unused) size: 0mb #s(0) s(0-0) chs: (0/0/0)-(0/0/0)d (0/0/0)-(0/0/0)r Primary partition(4) type: 000(0x00)(unused) size: 0mb #s(0) s(0-0) chs: (0/0/0)-(0/0/0)d (0/0/0)-(0/0/0)r Looking the first eight lines, it seems the data are still there... but I don't know how to recover them. I have a free second HD of about 500 GB (the formatted one is 320 GB) that I can use for the recovery process.

  Read the article

• apt-get : Size mismatch

  - by Cédric Girard

  I created a private deb repository to spread a software and it's updates to 600 Ubuntu netbooks. Each time the network is connected, my script try to do a apt-get update. But sometimes (quite often in fact), I have this : Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch The server is an 2.2 Apache, HTTPS only. There is no error on it's logs. Here is the script : apt-get update apt-get dist-upgrade --force-yes --yes Here is the complete output of apt-get Ign https://myserver maverick Release.gpg Ign https://myserver/ubuntu/ maverick/main Translation-en Ign https://myserver maverick Release Ign https://myserver maverick/main i386 Packages/DiffIndex Ign https://myserver maverick/main i386 Packages Ign https://myserver maverick/main i386 Packages Hit https://myserver maverick/main i386 Packages Reading package lists... Reading package lists... Building dependency tree... Reading state information... The following packages will be upgraded: majdb utilitaires voosicomat 3 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 6207kB/6273kB of archives. After this operation, 0B of additional disk space will be used. WARNING: The following packages cannot be authenticated! utilitaires voosicomat majdb Get:1 https://myserver/ubuntu/ maverick/main voosicomat all 2.0.1 [4755kB] Get:2 https://myserver/ubuntu/ maverick/main majdb all 1.0.17 [1452kB] Failed to fetch https://myserver/ubuntu/dists/maverick/main/binary-i386/voosicomat.deb Size mismatch Fetched 7091kB in 21s (324kB/s) E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Regards Cédric

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

< Previous Page | 891 892 893 894 895 896 897 898 899 900 901 902  | Next Page >