Search Results

Search found 27056 results on 1083 pages for 'build mode'.

Page 898/1083 | < Previous Page | 894 895 896 897 898 899 900 901 902 903 904 905  | Next Page >

  • Windows 7 boot problem (with colorful blinking smilies)

    - by Ishmael Smyrnow
    I put my computer (Windows 7) to sleep, and a couple hours later, tried to wake it back up, but the monitor wouldn't come back on. I did a hard reset (held power button), but I still couldn't get the monitor to show anything. I plugged it into my laptop, and the monitor works fine. I then swapped out the video card with an older one I have. The monitor came on and started showing the boot process. However, shortly after the Windows 7 animated logo came up, the screen went blank, it made this weird beeping noise, and I seen the strangest thing ever. Small, colorful blocks started to fill my screen, and flash, as if something was loading. Inside of those blocks, were smilies (like the ASCII character kind). This continued for about a minute, then the computer rebooted. It scared the sh!t out of me. I've never had a virus before, and I'm savvy enough to keep myself from one, but I'm wondering if that's what it was. I've been using computers for ages, and never seen anything quite like this. Has anyone ever seen something like this? I'm doing hardware diagnostics before trying to boot into Windows again. Hopefully I can figure this out, but I thought I would consult the SU community while I wait on these results. -- UPDATE -- I did a Memory Diagnostic, which turned up nothing. I also booted into Safe Mode no problem, and scheduled a disk check on both of my drives (I dual boot XP & 7). I was feeling good, and tried putting my regular video card back in, and the monitor won't display anything with it. Also, even though the monitor displays nothing, the system sounds like it's booting up. However, I hear a clicking in one of my hard drives that isn't there with the older video card. Could this be a problem with my hard drive, video card, or PSU? PSU makes sense, except for the fact I've been using the same setup for over a year, and the video card doesn't require it's own power plug thing.

    Read the article

  • JAVASCRIPT ENABLED

    - by kirchoffs415
    HI, I hope somebody can help, i keep getting the following message when i log on-- Your Javascript is disabled. Limited functionality is available. it will stay for maybe a day sometimes two.I have uninstalled javascript and reinstalled but still the same. Iam using chrome. any help would be gratefull many thanks Dominic p.s. my system spec is as follows System InformationOS Name Microsoft® Windows Vista™ Home Premium Version 6.0.6002 Service Pack 2 Build 6002 Other OS Description Not Available OS Manufacturer Microsoft Corporation System Name DOM-PC System Manufacturer Dell Inc. System Model Inspiron 1545 System Type X86-based PC Processor Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, 2000 Mhz, 2 Core(s), 2 Logical Processor(s) BIOS Version/Date Dell Inc. A05, 25/02/2009 SMBIOS Version 2.4 Windows Directory C:\Windows System Directory C:\Windows\system32 Boot Device \Device\HarddiskVolume3 Locale United Kingdom Hardware Abstraction Layer Version = "6.0.6002.18005" User Name DOM-PC\DOM Time Zone GMT Standard Time Installed Physical Memory (RAM) 3.00 GB Total Physical Memory 2.96 GB Available Physical Memory 1.38 GB Total Virtual Memory 5.89 GB Available Virtual Memory 4.25 GB Page File Space 3.00 GB Page File C:\pagefile.sys My System Specs

    Read the article

  • Google Chrome - Issues with download dialogs using BinaryWrite

    - by Mila
    Hello, I have an empty ASP .NET page with the code behind to support downloading of PDF files. The page is called from a link-like web control that has NavigateUrl set to this page. In short, I am using the following for streaming: Response.Buffer = false; Response.ClearHeaders(); Response.ContentType = "application/x-pdf"; Response.AddHeader("Content-Disposition","attachment; filename="MyPDFFile.pdf"); byte[] binary = (dataReaderRemote[DataPDFFieldName]) as byte[]; //dataReaderRemote[DataPDFFieldName] has previously retrieved data if (binary != null) { MemoryStream memoryStream = new MemoryStream(binary); int sizeToWrite = CHUNKSIZE; //CHUNKSIZE=1024 for (int i = 0; i < binary.GetUpperBound(0) - 1; i = i + CHUNKSIZE) { if (!Response.IsClientConnected) return; if (i + CHUNKSIZE >= binary.Length) sizeToWrite = binary.Length - i; byte[] chunk = new byte[sizeToWrite]; memoryStream.Read(chunk, 0, sizeToWrite); Response.BinaryWrite(chunk); Response.Flush(); } } Response.Close(); IE as well as Firefox bring the download prompt window asking you whether you wish to open or save the file, while the user remains on the same page containing the link. However, Google Chrome opens a new blank tab and downloads the file automatically. Is there any way to prevent Chrome from opening the extra blank and therefore useless tab? I am using the Google Chrome version 5.0.375.55 (Official Build 47796) on Windows XP. Thanks in advance! Mila

    Read the article

  • DIY NAS - links for Instructions

    - by Kaushik Gopal
    Good folk of SU, I'm planning to build a NAS (Network Access Storage). I'm planning to do it cheap (:read Old PC Config + Open source software). I was looking for good DIY links . Before you shoot this down as a Repost, I'm only looking for good links containing detailed instructions for setting up a NAS. I did a fair bit of searching and found these links (so please suggest others. While these links are great they delve more on the hardware side, i'm looking for more instructions in the software side). For the sake of the interwebs: Ubuntu: http://snarfquest.com/wiki/index.php/Setting_up_a_Home_NAS http://www.smallnetbuilder.com/content/view/27962/77/ http://jonpeck.blogspot.com/2006/11/how-to-configure-80-fileserver-in-45.html FreeNAS http://www.smallbusinesscomputing.com/webmaster/article.php/3719706 http://www.codeproject.com/KB/system/homemade_nas.aspxhttp://www.codeproject.com/KB/system/homemade_nas.aspx There was one at rubbervir.us that everyone points to, but apparently the site has gone down. A couple of other queries: Is Printer/Scanner sharing a possibility with NAS devices? Many talk of torrent support with NAS Devices, a little more light on this? Does this mean, an auto download of torrent through a feed into NAS, or just support for storing Torrent download files onto the NAS(don't see the difference between the latter and a normal file tranfer)

    Read the article

  • Why is 50.22.53.71 hitting my localhost node.js in an attempt to find a php setup

    - by laggingreflex
    I just created a new app using angular-fullstack yeoman generator, edited it a bit to my liking, and ran it with grunt on my localhost, and immediately upon starting up I get this flood of requests to paths that I haven't even defined. Is this a hacking attempt? And if so, how does the hacker (human or bot) immediately know where my server is and when it came online? Note that I haven't made anything online, it's just a localhost setup and I'm merely connected to the internet. (Although my router does allow 80 port incoming.) Whois shows that the IP address belongs to a SoftLayer Technologies. Never heard of it. Express server listening on 80, in development mode GET / [200] | 127.0.0.1 (Chrome 31.0.1650) GET /w00tw00t.at.blackhats.romanian.anti-sec:) [404] | 50.22.53.71 (Other) GET /scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/pma/scripts/setup.php [404] | 50.22.53.71 (Other) GET /admin/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /db/scripts/setup.php [404] | 50.22.53.71 (Other) GET /dbadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /myadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /mysql/scripts/setup.php [404] | 50.22.53.71 (Other) GET /mysqladmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /typo3/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin1/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin2/scripts/setup.php [404] | 50.22.53.71 (Other) GET /pma/scripts/setup.php [404] | 50.22.53.71 (Other) GET /web/phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /xampp/phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /web/scripts/setup.php [404] | 50.22.53.71 (Other) GET /php-my-admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /websql/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpmyadmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2/scripts/setup.php [404] | 50.22.53.71 (Other) GET /php-my-admin/scripts/setup.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2.5.5/index.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin-2.5.5-pl1/index.php [404] | 50.22.53.71 (Other) GET /phpMyAdmin/ [404] | 50.22.53.71 (Other) GET /phpmyadmin/ [404] | 50.22.53.71 (Other) GET /mysqladmin/ [404] | 50.22.53.71 (Other)

    Read the article

  • Distributing a custom command line tool to enterprise servers

    - by Jeremy Baker
    I've been tasked with building a command line tool that we will be providing to our enterprise customers so that they can use the API to upload data to our platform. The API works with standard cURL requests, so I can do most of the basic functionality with simple bash scripting, although I would like to provide something that is solid and really makes it easy for them to use and I don't know what I don't know. It's been a good 8 years since I've really done any serious sysadmin work. Most of the good tools I use these days are written in Ruby or Python and have a standard distribution process (Gems, for example). However, I know rhel and other platforms have their own package managers. Finally, the question: In today's day and age, what language / distribution method should I consider in order to cover the widest range of platforms without having to build completely different versions for each platform? I'd also love any general feedback you have about building similar projects, or links to projects that you think do a good job of this now and have open source code that I could read. Thanks in advance!

    Read the article

  • libvirt qemu/kvm migration problem

    - by Panda
    I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

    Read the article

  • VMware vSphere Hypervisor 5 with Intel SPL 5000 in Raid 0 no boot from DVD?

    - by Richard
    I hope this is the correct StackExchange, since I am only using StackOverflow for Web development, but need some help with my server configuration. I would like to install VMware vSphere Hypervisor 5 on my server here at home and run a view machines on it such as Windows Server 2008 and Red Hat. I used to have either OpenSuse or Windows Server 2008 installed but I would like to get into VMWare Hypervisor. My hardware configuration: - Intel S5000PSL with bios version S5000.86B.10.60.0091 build date 10/09/2008 as of read out of bios - E5420 @ 2.5GHz Intel Xeon CPU The Intel Virtualization Technology is enabled in the BIOS - DVD DH20A4P DVD Writer - 8GB ECC Ram I have configured a RAID 0 on my 2 WD 2TB SATA drives I have burned the Hypervisor 5 on an empty DVD and it is bootable, I tested it on my client PC. The main problem here is basically, that I cannot boot the DVD on my server. I have set the Boot Option to the DVD drive. I have booted from the BIOS straight in the DVD drive and it does not work. I do not see any error messages. The only thing I see are the PXE error messages when it tries booting from the network and other devices, obviously without any result. Does anybody know why I cannot boot the DVD? What could cause the problem? I have sucessfully installed Windows Server 2008 via original DVD about 1 year ago, so the DVD drive can read and does work. The DVD drive is available in the BIOS and I have checked all cables and none of them is loose in any way. I even see the light flashing but it does not want to boot from the DVD. I am looking forward to suggestions and things that I should check. Thank you very much

    Read the article

  • VMware virtual machine network devices malfunctioning

    - by sheepz
    I'm running Ubuntu 10.04 LTS and VMvware workstation 7.0.1 build-227600. The virtual machine i'm running in VMware is a custom distribution built on Debian Linux version 3.1. I'm still pretty much a beginner with UNIX administration. After having messed around with the vmware (changed only the name of the folder, the vmx and and other .v* files accordingly in which the .vmx was situated, and the configuration in the vmx file accordingly), the network devices on the virtual machine do not work anymore. The virtual machine is used for securely sending messages. The virtual machine: As far as I know, this perl file called proxy-gen-ifalias eth0 is responsible for properly setting up the two virtual network devices eth0 and eth1. The Virtual machine comes with a GUI interface in which I have set up two ethernet network devices, one internal, the other external. Now, after having messed around with this, the UI gives me this error message: perl proxy-gen-ifalias eth0 /etc/modprobe.d/alias-eth0 /sbin/update-modules perl proxy-gen-ifalias eth1 /etc/modprobe.d/alias-eth1 /sbin/update-modules ifdown eth0 ifdown: interface eth0 not configured ifdown eth1 ifdown: interface eth1 not configured perl proxy-gen-netcfg /etc/network/interfaces ifup eth0 SICCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. ifconfig eth0 eth0: error fetching interface information: Device not found make: *** [/etc/network/interfaces] Error 1 ~ Here are the contents of the two perl files referred to in the message: paste.pocoo.org/show/2AMzAYhoCRZqlGY7wUFk/ proxy-gen-netcfg

    Read the article

  • snort analysis of wireshark capture

    - by Ben Voigt
    I'm trying to identify trouble users on our network. ntop identifies high traffic and high connection users, but malware doesn't always need high bandwidth to really mess things up. So I am trying to do offline analysis with snort (don't want to burden the router with inline analysis of 20 Mbps traffic). Apparently snort provides a -r option for this purpose, but I can't get the analysis to run. The analysis system is gentoo, amd64, in case that makes any difference. I've already used oinkmaster to download the latest IDS signatures. But when I try to run snort, I keep getting the following error: % snort -V ,,_ -*> Snort! <*- o" )~ Version 2.9.0.3 IPv6 GRE (Build 98) x86_64-linux '''' By Martin Roesch & The Snort Team: http://www.snort.org/snort/snort-team Copyright (C) 1998-2010 Sourcefire, Inc., et al. Using libpcap version 1.1.1 Using PCRE version: 8.11 2010-12-10 Using ZLIB version: 1.2.5 %> snort -v -r jan21-for-snort.cap -c /etc/snort/snort.conf -l ~/snortlog/ (snip) 273 out of 1024 flowbits in use. [ Port Based Pattern Matching Memory ] +- [ Aho-Corasick Summary ] ------------------------------------- | Storage Format : Full-Q | Finite Automaton : DFA | Alphabet Size : 256 Chars | Sizeof State : Variable (1,2,4 bytes) | Instances : 314 | 1 byte states : 304 | 2 byte states : 10 | 4 byte states : 0 | Characters : 69371 | States : 58631 | Transitions : 3471623 | State Density : 23.1% | Patterns : 3020 | Match States : 2934 | Memory (MB) : 29.66 | Patterns : 0.36 | Match Lists : 0.77 | DFA | 1 byte states : 1.37 | 2 byte states : 26.59 | 4 byte states : 0.00 +---------------------------------------------------------------- [ Number of patterns truncated to 20 bytes: 563 ] ERROR: Can't find pcap DAQ! Fatal Error, Quitting.. net-libs/daq is installed, but I don't even want to capture traffic, I just want to process the capture file. What configuration options should I be setting/unsetting in order to do offline analysis instead of real-time capture?

    Read the article

  • Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

    - by David Brown
    Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

    Read the article

  • Windows Vista: Networking can only connect "local only"

    - by Damien
    I am attempting to debug a problem on a Windows Vista laptop - not mine! Until just recently (last week or so), it was operating normally for about 4 years :) The problem is that I am having issues connecting to the local network (a basic wireless home router; more later) and the internet (via ADSL). This is both for wired [Broadcom chipset] and wireless [Intel chipset]. I will elaborate further later. To detail the network. I have three other clients (HTC phone, Ubuntu 12.04 desktop [wired] and Ubuntu 10.04 laptop [wireless]), all of whom are able to connect to the network and internet normally. A windows 7 virtual machine running on said desktop connects normally. I have tried two different wireless routers - Netgear DG834G and Netgear DGN3500. The same error mode is common to both. Updating the firmware to the latest on both routers does not help. Overall, it seems safe to say it's localised to the laptop in question. I do not have another Vista client to test with. The specific symptoms are as follows: When "connected", it says "Local Only", and says it cannot connect to the internet. This is true for both wired and wireless. It can get an IP address (192.168.0.5), and the router (192.168.0.1) reports that it can see the device. When I try to ping, I get the following results: ping 192.168.0.1 - (router) all packets lost ping 192.168.0.5 - (laptop's address) OK ping 192.168.0.4 - (desktop) all packets lost Pinging from the desktop to the problematic laptop results in "From 192.168.0.4 icmp_seq=1 Destination Host Unreachable" The most promising "fix" from trawling forums is KB928233 which does not work for me. The problem is persistent across reports (both full shutdown and hibernate) so it appears not to be sleep related. I am not a regular vista user, though I can fumble my way about a bit. Is there any other suggestions as to what I should do? Is there any further information I can provide?

    Read the article

  • VMware Workstation update stopped autofit guest working

    - by u8sand
    VMware one day offered an update (8.0.1 build-528992 my current version) from 8.0. I accepted it, because updates usually fix problems. However not in this case... Previously it worked very well. Now, it still "works" but the one glitch I'm getting makes it too hard to deal with. This screenshot will explain my problem: As you can see, my virtual PC is not resizing correctly. (This happens with any operating system), autofit guest just doesn't work - it only results in things like this happening. Thanks to the tools it becomes very hard to NOT autofit guest. I've tried uninstalling 8.0.1 completely and installing 8.0 again but with the same results. I don't really understand what the new update has done to VMware Workstation or to my virtual machines. I do believe this isn't VMware Workstation's direct fault but from VMware Tools, which would explain why going back to 8.0 didn't work since VMware tools has its own updates. How can I fix this? The host is running Windows 7 Ultimate 64-bit.

    Read the article

  • SSH into Fedora 17 will not work with new users

    - by psion
    I just deployed a new Fedora 17 server on the Amazon EC2. I was able to log in as ec2-user with my generated keypair, but I cannot log in under normal circumstances as a user I created. This is just a normal ssh: ssh user@ip-address Any ideas on what is going on here? EDIT: This is a snippit from my sshd_config file # To disable tunneled clear text passwords, change to no here! PasswordAuthentication no #PermitEmptyPasswords no PasswordAuthentication no EDIT AGAIN: This is the output of ssh -v. OpenSSH_5.8p2, OpenSSL 1.0.0i-fips 19 Apr 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 107.23.2.165 [107.23.2.165] port 22. debug1: Connection established. debug1: identity file /home/psion/.ssh/id_rsa type 1 debug1: identity file /home/psion/.ssh/id_rsa-cert type -1 debug1: identity file /home/psion/.ssh/id_dsa type 2 debug1: identity file /home/psion/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9 debug1: match: OpenSSH_5.9 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 19:cb:84:21:a9:0e:83:96:2f:6a:fa:7d:ce:39:0f:31 debug1: Host '107.23.2.165' is known and matches the RSA host key. debug1: Found key in /home/psion/.ssh/known_hosts:5 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_1000' not found debug1: Unspecified GSS failure. Minor code may provide more information Credentials cache file '/tmp/krb5cc_1000' not found debug1: Unspecified GSS failure. Minor code may provide more information debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Offering DSA public key: /home/psion/.ssh/id_dsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug1: Offering RSA public key: /home/psion/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic debug1: No more authentication methods to try. Permission denied (publickey,gssapi-keyex,gssapi-with-mic).

    Read the article

  • Virtual bridged networking with VLAN, could not ping

    - by v.yegy
    I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

    Read the article

  • How to rip AVI from VOB using ffmpeg

    - by Linux Jedi
    I am trying to convert a VOB to an AVI. I have ripped an AVI from this VOB before using ffmpeg, but for some reason it's not working this time. This is what I tried: ffmpeg -sameq -acodec copy -i VTS_01_2.VOB output.avi This is the output I get: FFmpeg version 0.6.1, Copyright (c) 2000-2010 the FFmpeg developers built on Dec 29 2010 18:02:10 with gcc 4.2.1 (Apple Inc. build 5664) configuration: libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0.11. 0 / 0.11. 0 [mpeg2video @ 0x101014200]mpeg_decode_postinit() failure Last message repeated 6 times Input #0, mpeg, from 'VTS_01_2.VOB': Duration: 26:30:29.20, start: 140.171311, bitrate: 90 kb/s Stream #0.0[0x1e0]: Video: mpeg2video, yuv420p, 720x480 [PAR 32:27 DAR 16:9], 9800 kb/s, 31.44 fps, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1[0xa0]: Audio: pcm_s16be, 48000 Hz, 2 channels, s16, 1536 kb/s Output #0, avi, to 'output.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 720x480 [PAR 32:27 DAR 16:9], q=2-31, 200 kb/s, 29.97 tbn, 29.97 tbc Stream #0.1: Audio: pcm_s16be, 48000 Hz, 2 channels, 1536 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Could not write header for output file #0 (incorrect codec parameters ?)

    Read the article

  • Puppet and Vim fighting over Ruby version

    - by devians
    I have installed puppet from the .dmg from puppetlabs. If I remove ruby 1.9.3, puppet works, but other things like my vim install (dependant plugins) do not. According to http://docs.puppetlabs.com/guides/platforms.html#ruby-versions 1.9.3 is supported. So whats going wrong with puppet? % uname -a Darwin Kusanagi.local 11.4.2 Darwin Kernel Version 11.4.2: Thu Aug 23 16:25:48 PDT 2012; root:xnu-1699.32.7~1/RELEASE_X86_64 x86_64 % which ruby /usr/local/bin/ruby % ruby --version ruby 1.9.3p327 (2012-11-10 revision 37606) [x86_64-darwin11.4.2] % /usr/bin/ruby --version ruby 1.8.7 (2012-02-08 patchlevel 358) [universal-darwin11.0] % brew info ruby 1 ? ruby: stable 1.9.3-p327, HEAD http://www.ruby-lang.org/en/ Depends on: pkg-config, readline, gdbm, libyaml /usr/local/Cellar/ruby/1.9.3-p327 (796 files, 17M) * https://github.com/mxcl/homebrew/commits/master/Library/Formula/ruby.rb ==> Options --with-tcltk Install with Tcl/Tk support --with-suffix Suffix commands with "19" --universal Build a universal binary --with-doc Install documentation ==> Caveats NOTE: By default, gem installed binaries will be placed into: /usr/local/Cellar/ruby/1.9.3-p327/bin You may want to add this to your PATH. % puppet /usr/local/Cellar/ruby/1.9.3-p327/lib/ruby/1.9.1/rubygems/custom_require.rb:36:in `require': cannot load such file -- puppet/util/command_line (LoadError) from /usr/local/Cellar/ruby/1.9.3-p327/lib/ruby/1.9.1/rubygems/custom_require.rb:36:in `require' from /usr/bin/puppet:3:in `<main>'

    Read the article

  • How to plug power/reset buttons from case to motherboard leads?

    - by MaxMackie
    I have a motherboard I salvaged from a pre-assembled computer. Except now I'm trying to use it in my own custom build. The problem is, this motherboard doesn't have any documentation because it was never meant to be used by consumers (as far as I know). I need to plug in my case's power/reset/hdd-light plugs into the motherboard. I usually check the documentation of the board to see which leads go to what connector, but I have no documentation for the board. So, as I see it, I have two options: I find the documentation (I've emailed gateway customer service, but I'm unsure of how successful I'll be with that). I simply test the leads one after the other (can this cause damage if plugged into the wrong leads?) However, there might even be a standard for which leads do what action (I'm not sure about this). For reference, my motherboard's SN/MD (?) is: H57M01G1-1.1-8EKS3H Does anyone have any idea if I can find documentation or find another way to be sure if my connections are correct?

    Read the article

  • Recompiling Nginx 1.4.3 with "--with-http_gzip_static_module" error

    - by Elijah Paul
    I'm trying to enable the 'ngx_http_gzip_static_module' module in Nginx 1.4.3 by adding the --with-http_gzip_static_module to my ./configure configuration. But I recieve the following error when i try to recompile (make): # make make -f objs/Makefile make[1]: Entering directory `/tmp/nginx-1.4.3' make[1]: *** No rule to make target `src/os/unix/ngx_gcc_atomic_x86.h', needed by `objs/src/core/nginx.o'. Stop. make[1]: Leaving directory `/tmp/nginx-1.4.3' make: *** [build] Error 2 My current config (CentOS 6.4): # nginx -V nginx version: nginx/1.4.3 built by gcc 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) TLS SNI support enabled configure arguments: --conf-path=/etc/nginx/nginx.conf --pid-path=/var/run/nginx.pid --error-log-path=/var/log/nginx/error.log --http-proxy-temp-path=/var/cache/nginx/proxy_temp --http-fastcgi-temp-path=/var/cache/nginx/fastcgi_temp --http-uwsgi-temp-path=/var/cache/nginx/uwsgi_temp --http-scgi-temp-path=/var/cache/nginx/scgi_temp --http-log-path=/var/log/nginx/access.log --with-http_ssl_module --prefix=/usr --add-module=./nginx-sticky-module-1.1 --add-module=./headers-more-nginx-module-0.23 i was under the impression that this was a module that just need to be 'enabled' as opposed to 'added'. What am I missing here?

    Read the article

  • Lightweight Linux distro that includes developer tools? (or, the most BSD-like Linux)

    - by RevAaron
    I cut my teeth on Minix and Slackware 1.1, but I've been in the OS X Wilderness for the last few years. I'm trying to standardize on a Linux distribution for personal and work-related use on less powerful laptops and under virtualization. So far, NetBSD and OpenBSD are the best fit for my purposes- but after plenty of frustration I've come to the conclusion that I need to stick with Linux to get the hardware and software support that comes with it. What I like about NetBSD/OpenBSD that I'd like to keep: X, but no default KDE, GNOME or XFCE! A sensible /etc and dot file setup- startx calls xinit, xinit looks for ~/.xinitrc; nothing more complicated than that is needed. Command line tools and file-based configuration: I shouldn't need a GUI to connect to a WAP. Decent selection of binary packages; building from source is OK, but nothing source-only like Gentoo. pkg_add (BSD) and apt-get both have treated me well in the past. Modest RAM and HDD requirements: boot + X + awesome+ two xterms takes up 80 MB on OpenBSD and 240 MB on Debian 5 and Crunchbang In my experience, most "lightweight" and Live CDs focus on a nice desktop environment crammed into a CD or USB stick; once you add build-essentials you end up with something just about as bloated as Ubuntu or Debian full install. Crunchbang is a great example. Thanks in advance for all suggestions!

    Read the article

  • deploy LAMP config to new boxes with low/no effort

    - by user1444233
    I'm spending a lot of time setting up new Centos 6 instances. I use a VCS (Subversion) for most of the config files and all of the webapp source files (Github), but even with excellent package managers (like yum, npm, easy_install, etc.) it still takes time. I'd like to get to the point where I could try out a new potential web host by just signing up for an account, logging in and automatically sucking my standardised config onto the box. I know there are a set of tools that can help: Puppet Chef Vagrant and a set of services that sell solutions: [Jumpbox] http://www.jumpbox.com/ [BitNami Cloud] http://bitnami.org/cloud I don't mind investing time in learning a new tool, but as a no-budget start-up, I'm keen to keep monthly costs down. My biggest concern is that time spent on the server config is time away from the codebase, and that's where I think my team and I should be investing our energy, at least until we get funded and scale up a bit. I'd be grateful of some recommendations for which way to jump on config: stick with SSH and manual deploys, at least until you get big. bite the bullet and learn [say] puppet. You may only use it 8-10 times, but it pays to have such an easy tunable server bootstrap. don't bother, just pay the $100/month for a standard config service. It'll cost you $1000/year, but you should focus on the code. Other questions in this domain I use quite a complex stack (Drupal, Zend Server, MySQL, PHP, MongoDB, Python, django), but are there standard(ish) setups that include these or that I could build upon more quickly? Are the configs optimised for small, medium, large VPS (1GB, 4GB, 16GB)? How secure are they?

    Read the article

  • WIM2VHD failing with "Cannot derive Volume GUID from mount point."

    - by Jacob
    I'm trying to use WIM2VHD according to the instructions on Scott Hanselman's blog post to create a Sysprepped VHD image to boot from. I've installed the WAIK, and I have my Windows 7 sources mounted as a virtual drive. When I try to run WIM2VHD like this: cscript WIM2VHD.wsf /wim:F:\sources\install.wim /sku:Ultimate /vhd:E:\WindowsSeven.vhd /size:30721 I get the following log: Log for WIM2VHD 6.1.7600.0 on 11/2/2009 at 10:51:18.16 Copyright (C) Microsoft Corporation. All rights reserved. MACHINE INFO: Build=7600 Platform=x86fre OS=Windows 7 Ultimate ServicePack= Version=6.1 BuildLab=win7_rtm BuildDate=090713-1255 Language=en-ZA INFO: Looking for IMAGEX.EXE... INFO: Looking for BCDBOOT.EXE... INFO: Looking for BCDEDIT.EXE... INFO: Looking for REG.EXE... INFO: Looking for DISKPART.EXE... INFO: Session key is E01E1ED7-C197-4814-BDE4-43B73E14FCC4 INFO: Inspecting the WIM... INFO: Configuring and formatting the VHD... ******************************************************************************* Error: 0: Cannot derive Volume GUID from mount point. ******************************************************************************* INFO: Unmounting the VHD due to error... WARNING: In order to help resolve the issue, temporary files have not been deleted. They are in: C:\Users\Jacob\AppData\Local\Temp\WIM2VHD.WSF\E01E1ED7-C197-4814-BDE4-43B73E14FCC4 *emphasized text*Summary: Errors: 1, Warnings: 1, Successes: 0 INFO: Done. Any ideas?

    Read the article

  • Mac 10.5 Python libsvm 64 bit vs 32 bit

    - by shadowsoul
    I have a Mac 10.5 when I type "python" in terminal, it says Enthought Python Distribution -- www.enthought.com Version: 7.3-2 (64-bit) Python 2.7.3 |EPD 7.3-2 (64-bit)| (default, Apr 12 2012, 11:14:05) [GCC 4.0.1 (Apple Inc. build 5493)] on darwin Type "credits", "demo" or "enthought" for more information. then I go to my libsvm/python folder and type "make" which results in make -C .. lib if [ "Darwin" = "Darwin" ]; then \ SHARED_LIB_FLAG="-dynamiclib -W1,-install_name,libsvm.so.2"; \ else \ SHARED_LIB_FLAG="-shared -W1,-soname,libsvm.so.2"; \ fi; \ g++ ${SHARED_LIB_FLAG} svm.o -o libsvm.so.2 when I try to do "from svmutil import *" I get the error: OSError: dlopen(.../libsvm-3.12/python/../libsvm.so.2, 6): no suitable image found. Did find: .../libsvm-3.12/python/../libsvm.so.2: mach-o, but wrong architecture when I do "lipo -info libsvm.so.2", I get: Non-fat file: libsvm.so.2 is architecture: i386 So it looks like I'm running 64-bit python but libsvm ends up as a 32-bit program. Any way I can get it to compile as a 64-bit program?

    Read the article

  • DKIM error: dkim=neutral (bad version) header.i=

    - by GBC
    Ive been struggling the last couple of hours with setting up DKIM on my Postfix/CentOS 5.3 server. It finally sends and signs the emails, but apparently Google still does not like it. The errors I'm getting are: dkim=neutral (bad version) [email protected] from googles "show original" interface. This is what my DKIM-signature header look like: v=1; a=rsa-sha1; c=simple/simple; d=mydomain.com.au; s=default; t=1267326852; bh=0wHpkjkf7ZEiP2VZXAse+46PC1c=; h=Date:From:Message-Id:To:Subject; b=IFBaqfXmFjEojWXI/WQk4OzqglNjBWYk3jlFC8sHLLRAcADj6ScX3bzd+No7zos6i KppG9ifwYmvrudgEF+n1VviBnel7vcVT6dg5cxOTu7y31kUApR59dRU5nPR/to0E9l dXMaBoYPG8edyiM+soXo7rYNtlzk+0wd5glgFP1I= Very appreciative of any suggestions as to how I can solve this problem! Btw, here is exactly how I installed dkim-milter in CentOS 5.3 for postfix, if anyone is interested (based on this guide): mkdir dkim-milter cd dkim-milter wget http://www.topdog-software.com/oss/dkim-milter/dkim-milter-2.8.3-1.x86_64.rpm ======S====== Newest version: http://www.topdog-software.com/oss/dkim-milter/ ======E====== rpm -Uvh dkim-milter-2.8.3-1.x86_64.rpm /usr/bin/dkim-genkey -r -d mydomain.com.au ======S====== add contents of default.txt to DNS as TXT _ssp._domainkey TXT dkim=unknown _adsp._domainkey TXT dkim=unknown default._domainkey TXT v=DKIM1; g=*; k=rsa; p=MIGfMA0GCSqGSIb3DQEBAQUAA4GWETBNiQKBgQC5KT1eN2lqCRQGDX+20I4liM2mktrtjWkV6mW9WX7q46cZAYgNrus53vgfl2z1Y/95mBv6Bx9WOS56OAVBQw62+ksXPT5cRUAUN9GkENPdOoPdpvrU1KdAMW5c3zmGOvEOa4jAlB4/wYTV5RkLq/1XLxXfTKNy58v+CKETLQS/eQIDAQAB ======E====== mv default.private default mkdir /etc/mail/dkim/keys/mydomain.com.au mv default /etc/mail/dkim/keys/mydomain.com.au chmod 600 /etc/mail/dkim/keys/mydomain.com.au/default chown dkim-milt.dkim-milt /etc/mail/dkim/keys/mydomain.com.au/default vim /etc/dkim-filter.conf ======S====== ADSPDiscard yes ADSPNoSuchDomain yes AllowSHA1Only no AlwaysAddARHeader no AutoRestart yes AutoRestartRate 10/1h BaseDirectory /var/run/dkim-milter Canonicalization simple/simple Domain mydomain.com.au #add all your domains here and seperate them with comma ExternalIgnoreList /etc/mail/dkim/trusted-hosts InternalHosts /etc/mail/dkim/trusted-hosts KeyList /etc/mail/dkim/keylist LocalADSP /etc/mail/dkim/local-adsp-rules Mode sv MTA MSA On-Default reject On-BadSignature reject On-DNSError tempfail On-InternalError accept On-NoSignature accept On-Security discard PidFile /var/run/dkim-milter/dkim-milter.pid QueryCache yes RemoveOldSignatures yes Selector default SignatureAlgorithm rsa-sha1 Socket inet:20209@localhost Syslog yes SyslogSuccess yes TemporaryDirectory /var/tmp UMask 022 UserID dkim-milt:dkim-milt X-Header yes ======E====== vim /etc/mail/dkim/keylist ======S====== *@mydomain.com.au:mydomain.com.au:/etc/mail/dkim/keys/mydomain.com.au/default ======E====== vim /etc/postfix/main.cf ======S====== Add: smtpd_milters = inet:localhost:20209 non_smtpd_milters = inet:localhost:20209 milter_protocol = 2 milter_default_action = accept ======E====== vim /etc/mail/dkim/trusted-hosts ======S====== localhost 127.0.0.1 ======E====== /etc/mail/local-host-names ======S====== localhost 127.0.0.1 ======E====== /sbin/chkconfig dkim-milter on /etc/init.d/dkim-milter start /etc/init.d/postfix restart

    Read the article

  • Layer 3 switch routing

    - by Yoshiwaan
    I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

    Read the article

< Previous Page | 894 895 896 897 898 899 900 901 902 903 904 905  | Next Page >