Search Results

Search found 24624 results on 985 pages for 'linux rrt'.

Page 910/985 | < Previous Page | 906 907 908 909 910 911 912 913 914 915 916 917  | Next Page >

• How can I stream audio signals from various devices/computers to my home server?

  - by Breakthrough

  I currently have a headless home server set up (running Ubuntu 12.04 server edition) running a simple Apache HTTP server. The server is near an audio receiver, which controls a set of indoor and outdoor speakers in my home. Recently, my father purchased a Bluetooth adapter, which our various laptops and cellphones can connect to, outputting the music to the speakers. I was hoping to find a solution that worked over Wi-Fi, namely because it won't cost anything (I already have a server with an audio card), and it doesn't depend on Bluetooth. Is there any cross-platform (preferably free and open-source) solution that I can use which will allow me to stream audio to my home server, over my home network, from a wide variety of devices (laptops running Windows/Linux or cellphones running Android/BB/iOS)? I need something that works at least with Windows and Android. Also, just to clairfy, I want something that simply allows devices to connect to my server and output an audio signal without any action on the server end (since it's a server hidden away near my receiver). Any subsequent connection attempt should be dropped, so only one device can be in control of the stereo at once.

  Read the article

• How to redirect all Internet traffic to OpenVPN Server

  - by JuliaS

  I have seen working solutions around the issue of forcing Internet traffic to go through the OpenVPN server but they are all done in Linux, all I want to know is how to add an entry to the route table in windows to make this happen. connectivity between the client and server is fine, my Windows 7 client can establish a connection to the Windows 2008 Server, but when established Internet traffic is still going from the local Windows 7 machine. Here are the details: Server: Windows 2008 Server with one NIC OpenVPN IP Address: 192.168.0.1 Local NIC IP Address (connects the server to the Internet): 10.242.69.107 Client: Windows 7 with one NIC OpenVPN IP Address: 192.168.0.2 ISP allocated IP Address: 10.0.8.2 (gateway 10.0.8.1) Server OpenVPN Config: dev tun ifconfig 192.168.0.1 192.168.0.2 secret static.key push "redirect-gateway def1" Client OpenVPN Config: remote xxx.xxx.com dev tun ifconfig 192.168.0.2 192.168.0.1 secret static.key I'm not an expert with adding routes...etc. I would be grateful if someone could let me know how to add this entry in my server/client route table. EDIT: Output from the client's netstat -rnv IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.8.1 10.0.8.2 20 10.0.8.0 255.255.255.252 On-link 10.0.8.2 276 10.0.8.2 255.255.255.255 On-link 10.0.8.2 276 10.0.8.3 255.255.255.255 On-link 10.0.8.2 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.252 On-link 192.168.0.2 286 192.168.0.2 255.255.255.255 On-link 192.168.0.2 286 192.168.0.3 255.255.255.255 On-link 192.168.0.2 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.8.2 276 224.0.0.0 240.0.0.0 On-link 192.168.0.2 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.8.2 276 255.255.255.255 255.255.255.255 On-link 192.168.0.2 286 ===========================================================================

  Read the article

• centos 6 debuginfo repository does not have httpd debug version available

  - by Zippy Zeppoli

  I am trying to get the debug version of httpd so I can use it in conjunction with gdb. I am having a hard time getting them, and they don't seem to be in the standard epel-debuginfo repository. What should I do? > [root@buildbox-rhel6 ~]# debuginfo-install httpd Loaded plugins: fastestmirror, presto enabling epel-debuginfo Loading mirror speeds from cached hostfile epel-debuginfo/metalink | 8.3 kB 00:00 * base: mirrors.cicku.me * epel: mirrors.kernel.org * epel-debuginfo: mirrors.kernel.org * extras: mirrors.arpnetworks.com * updates: linux.mirrors.es.net epel-debuginfo | 3.1 kB 00:00 epel-debuginfo/primary_db | 487 kB 00:01 Checking for new repos for mirrors Could not find debuginfo for main pkg: httpd-2.2.15-15.el6.centos.1.x86_64 Could not find debuginfo pkg for dependency package apr-1.3.9-5.el6_2.x86_64 Could not find debuginfo pkg for dependency package apr-util-1.3.9-3.el6_0.1.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package db4-4.7.25-17.el6.x86_64 Could not find debuginfo pkg for dependency package expat-2.0.1-11.el6_2.x86_64 Could not find debuginfo pkg for dependency package openldap-2.4.23-26.el6_3.2.x86_64 Could not find debuginfo pkg for dependency package openldap-2.4.23-26.el6_3.2.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package pcre-7.8-4.el6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package libselinux-2.0.94-5.3.el6.x86_64 Could not find debuginfo pkg for dependency package zlib-1.2.3-27.el6.x86_64 No debuginfo packages available to install

  Read the article

• Squid, authentication, Outlook Anywhere, Windows 7 and HTTP 1.1 = NIGHTMARE

  - by Massimo

  I'm running a Squid proxy (latest version, 3.1.4) on Linux CentOS 5.4 with Samba 3.5.4, in order to allow authenticated web access for domain users; everything works fine, and even Windows 7 clients are fully supported. Authentication is transparent for domain users, while it is explicitly requested for non-domain ones, and it works if the user can provide valid domain credentials. All nice and good. Then, Outlook Anywhere kicks in and pain and suffering ensue. When Outlook (be it 2007 or 2010, it doesn't matter) runs on Windows XP clients, it connects gracefully through the Squid proxy to its remote Exchange server. When it runs on Windows 7, it doesn't. If the authentication requirement is lifted from the proxy, everything works on Windows 7 too, so the problem is obviously related to NTLM authentication with Squid. Digging more deeply (WireShark), I discovered Outlook Anywhere uses HTTP 1.1 when it runs on Windows 7, while it uses HTTP 1.0 when on Windows XP. And it looks like Squid, even in its latest incarnation, still has some serious troubles handling HTTP 1.1 properly, particularly when SSL and proxy authentication are thrown in the mix. While waiting for Squid to fully and officially support HTTP 1.1 (and it looks like this could take quite a long time), I'm looking for one of the following solutions: Make Squid handle this correctly, if it is at all possible. Identify Outlook Anywhere connections and have Squid not require authentication for them. But it isn't easy: again, the behaviour of Outlook differs when running on Windows XP and Windows 7, and while on Windows XP Outlook sends a really nice user-agent string of "MSRPC", on Windows 7 it doesn't send any (why? WHY?!?). Force Outlook Anywhere to use HTTP 1.0 even when running on Windows 7. And no, this is not as simple as deselecting "use HTTP 1.1" in Internet Explorer, looks like Outlook ignores that setting and chooses on its own which protocol to use. Any other feasible solution which doesn't involve whitelisting specific destination Exchange servers, which is the last-resort solution I'm trying to avoid.

  Read the article

• How to bypass resume from hibernate

  - by Daniel Trebbien

  I am attempting to resume a Windows Vista laptop from hibernate, but the resume process seems to be stuck in an endless loop in which Windows is repeatedly trying to read from the optical drive. When I press the Power On button on the laptop, the screen is black (not even the backlight turns on) and the following occurs in a loop: Five seconds pass and I hear the optical drive being accessed. (There's no disk in the drive, so it sounds like a short buzzing noise.) Two seconds pass and I hear the optical drive being accessed. Two seconds pass and I hear the optical drive being accessed. So it's three short buzzing noises in a row, over and over again. Eventually I have to abruptly power off the machine. I have tried inserting a data CD into the drive as well as a bootable CD (a live Linux distro boot disk). For both, the optical drive spins up for a bit, but stops after Windows decides that the disk is not what it is looking for. I have since lost the Windows Vista recovery DVD, but I don't know if inserting the recovery disk into the optical drive would have a different effect than the bootable CD. I have tried pressing F8 immediately after pressing the Power On button (hoping to enter System Restore), but that did not have an effect. Is there a special key sequence that will cause Windows to bypass resuming from hibernate, effectively ignoring hiberfil.sys?

  Read the article

• Problems with OpenVPN setup

  - by user70617

  Hi, I'm trying to set up a VPN server using OpenVPN and I'm getting some errors while trying to connect the client to the server. I'm getting the following error: Sun Feb 13 14:54:16 2011 OpenVPN 2.1.4 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] built on Feb 5 2011 Sun Feb 13 14:54:16 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Sun Feb 13 14:54:16 2011 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sun Feb 13 14:54:16 2011 ******* WARNING *******: all encryption and authentication features disabled -- all data will be tunnelled as cleartext Sun Feb 13 14:54:16 2011 RESOLVE: NOTE: localhost resolves to 2 addresses Sun Feb 13 14:54:16 2011 Note: Cannot ioctl TUNSETIFF tap0: Device or resource busy (errno=16) Sun Feb 13 14:54:16 2011 Note: Attempting fallback to kernel 2.2 TUN/TAP interface Sun Feb 13 14:54:16 2011 Cannot open TUN/TAP dev /dev/tap0: No such file or directory (errno=2) Sun Feb 13 14:54:16 2011 Exiting I have bridge-utils installed and tap0 shows up in ifconfig. Can anybody give me a hand? Thanks in advance.

  Read the article

• Choosing the right TV tuner - USB or PCI TV tuners, hardware/software, DVB? Hybrid/combo/analog?

  - by Nucleon

  Greetings, I'll start with some background information so you know what I'm trying to accomplish and then get to my question. I work at a Television station in the US and we are working on setting up an online DVR/Podcast system for all of our newscasts. So basically we would be recording every newscast in HD, encoding it to flv/h.264 for viewing in a browser on flash compatible and iphone/ipad devices, eventually migrating to WebM when it's browser compliant. This task is theoretically pretty simple as it all it involves is a TV tuner device and a program like VLC, MythTV or whatever to schedule and dump it to a file, encode it with VLC/FFMPEG and push it to the streaming server. Now to the hardware, in order to accomplish that task, should I use an internal PCI tuner or a USB 2.0 tuner? Is there a difference? The bus speeds of both are not too far apart, and is the bus speed really relevant in this case? Does it matter if the device has a hardware encoder or a software encoder? On many sites the USB was recommended for ease of set up and use, but would it overly task a processor, or is that not a concern as long as it's a decent PC (at least duo core, 6gb ram). What's the difference between the stick USB and the Box USBs? To my understanding analog is basically gone in the US, so we would want a hybrid or combo tuner correct? How do those differ from DVB? Are there any other features or concepts which I am missing which may influence the recommended product. It would be ideal if the device which could work in both Linux and a Windows environment, to my knowledge most Hauppauge are? Example 1: PCI Hauppage http://www.newegg.com/Product/Product.aspx?Item=N82E16815116033 Example 2: USB 2.0 Box http://www.newegg.com/Product/Product.aspx?Item=N82E16815116029 Example 3: USB 2.0 Stick http://www.newegg.com/Product/Product.aspx?Item=N82E16815116031 Any guidance from the Superusers would be much appreciated!

  Read the article

• iptables (NAT/PAT) setup for SSH & Samba

  - by IanVaughan

  I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - 192.168.109.15 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Any help?

  Read the article

• Acer Aspire One getting extremely hot

  - by ascom

  I have an Acer Aspire One D250-1197. I really better type fast before it overheats again... For some reason, I'm having a problem with heat on my netbook only when I run Joli OS (Ubuntu 9.10 LTS?). When I leave it idle, with nothing running (other than the regular Joli OS desktop and a couple of doing-nothing terminals), heat slowly builds up to the point where the netbook is burning hot to the touch. I have never had this problem when running Windows 7 Starter (even though it gives me plenty of other headaches). It seems that the fan is spinning, but not fast enough to keep up with the heat buildup. Is there something wrong with the fan drivers? The computer doesn't seem to recognize that it is overheating. What can I do to solve this problem (other than shut it off or use Windows)? I'm currently on the wrong side of Earth (I mean, on vacation), so I just need a temporary fix, such as a driver I can install. Also, I have to use Linux, because I have to share out the wired connection in hotels wirelessly to the iPhones. EDIT: I'm switching from Joli OS to a more "proper" and up to date distribution (Xubuntu 13.04). I'll see if it still has the heat problem and try @nod's cpufreq idea.

  Read the article

• ssh X11 forwarding issue

  - by bbuser

  I have put ForwardX11 in my ~/.ssh/config and then I start a X11 application like this: ssh -f user@host 'someapp; sleep 1' This works fine. The application someapp has a button which opens a viewer application via a shell script viewer.sh. When I press the button the viewer comes up. This is all good and as expected, but if I do ssh -2 -f user@host 'someapp; sleep 1' there's trouble. someapp starts very well, but if I click the button the viewer doesn't show up. As the viewer is called via a shell script, I replaced the call with xclock and the situation was exactly the same - I think the viewer is not to blame. The situation is the same on Linux and AIX. The reason I need -2 is that I finally want to use connection multiplexing and this does only work with version 2. The reason for the sleep 1 is that it didn't work otherwise;-) To add more confusion, with ssh -2 -f user@host 'xterm &; app; sleep 1' the viewer works as long as the xterm is open. When I close xterm ssh -v outputs the following debug1: channel 1: FORCE input drain debug1: channel 0: free: client-session, nchannels 3 debug1: channel 1: free: x11, nchannels 2 and from that moment the viewer doesn't show when I press the button. I also replaced the viewer application with a script that writes the $DISPLAY variable to a file. The variable is always set correctly.

  Read the article

• Running gdb on Ubuntu 9.10 Apache2 Install

  - by AJ

  Hi all, I am trying to run gdb to debug my Ubuntu 9.10 Apache2 install and having a couple of problems: It seems like the package installed by Ubuntu for Apache2 does not include debugging symbols; is there a different version of the package I should be using for developing/debugging? When I try to run gdb, I get an error that looks to be caused by some missing environment variable. Are there additional options I should pass to "run" to get this to work? Here is the output of the debugger session: root@aj-ubuntu:/usr/sbin# gdb apache2 GNU gdb (GDB) 7.0-ubuntu Copyright (C) 2009 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html> This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details. This GDB was configured as "x86_64-linux-gnu". For bug reporting instructions, please see: <http://www.gnu.org/software/gdb/bugs/>... Reading symbols from /usr/sbin/apache2...(no debugging symbols found)...done. (gdb) run -X Starting program: /usr/sbin/apache2 -X [Thread debugging using libthread_db enabled] apache2: bad user name ${APACHE_RUN_USER} Program exited with code 01. (gdb) Thanks in advance, -aj

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• Debian amd64 on Dell Studio 540 reboot hangs

  - by Shcheklein

  Hi, I have Dell Studio 540 desktop and Debian Lenny installed on it: 2.6.26-2-amd64 #1 SMP Tue Mar 9 22:29:32 UTC 2010 x86_64 GNU/Linux The problem is that I can't reboot it. It just hangs after "Will now restart" message. I've already tried: reboot=b, reboot=a, reboot=h kernel options. Nothing helps. Additional info (I can provide any other information): dmidecode System Information Manufacturer: Dell Inc. Product Name: Studio 540 lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 3 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller 02:00.0 FireWire (IEEE 1394): JMicron Technologies, Inc. Device 2380 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)

  Read the article

• Solaris ldap Authentication

  - by Tman

  Iv been having a trouble trying to get my Solaris 10 server to authenticate against an eDir server.im managed to Set up my linux(RHeL,SLES) servers to authenticate against the ldap Server.which works fine. Here is my configuration Files. ldapclient list: NS_LDAP_FILE_VERSION= 2.0 NS_LDAP_BINDDN= cn=proxyuser,o=AEDev NS_LDAP_BINDPASSWD= {NS1}ecfa88f3a945c22222233 NS_LDAP_SERVERS= 192.168.0.19 NS_LDAP_SEARCH_BASEDN= ou=auth,o=AEDev NS_LDAP_AUTH= simple NS_LDAP_SEARCH_SCOPE= sub NS_LDAP_CACHETTL= 0 NS_LDAP_CREDENTIAL_LEVEL= anonymous NS_LDAP_SERVICE_SEARCH_DESC= group:ou=Groups,ou=auth,o=AEDev NS_LDAP_SERVICE_SEARCH_DESC= shadow:ou=users,ou=auth,o=AEDev?sub?objectClass=shadowAccount NS_LDAP_SERVICE_SEARCH_DESC= passwd:ou=auth,o=AEDev?sub?objectClass=posixAccount NS_LDAP_BIND_TIME= 10 NS_LDAP_SERVICE_AUTH_METHOD= pam_ldap:simple getent passwd works fine: root:x:0:0:Super-User:/:/sbin/sh daemon:x:1:1::/: bin:x:2:2::/usr/bin: sys:x:3:3::/: adm:x:4:4:Admin:/var/adm: lp:x:71:8:Line Printer Admin:/usr/spool/lp: uucp:x:5:5:uucp Admin:/usr/lib/uucp: nuucp:x:9:9:uucp Admin:/var/spool/uucppublic:/usr/lib/uucp/uucico smmsp:x:25:25:SendMail Message Submission Program:/: listen:x:37:4:Network Admin:/usr/net/nls: gdm:x:50:50:GDM Reserved UID:/: webservd:x:80:80:WebServer Reserved UID:/: postgres:x:90:90:PostgreSQL Reserved UID:/:/usr/bin/pfksh svctag:x:95:12:Service Tag UID:/: nobody:x:60001:60001:NFS Anonymous Access User:/: noaccess:x:60002:60002:No Access User:/: nobody4:x:65534:65534:SunOS 4.x NFS Anonymous Access User:/: tlla:x:2012:100::/home/tlla: test:x:2011:100::/home/test: thato:x:2010:100::/home/thato: pam.conf login auth sufficient pam_unix_auth.so.1 #server_policy login auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass login auth required pam_dial_auth.so.1 rlogin auth sufficient pam_rhosts_auth.so.1 rlogin auth requisite pam_authtok_get.so.1 rlogin auth required pam_dhkeys.so.1 rlogin auth required pam_unix_cred.so.1 rlogin auth sufficient pam_unix_auth.so.1 rlogin auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass rsh auth sufficient pam_rhosts_auth.so.1 rsh auth required pam_unix_cred.so.1 rsh auth sufficient pam_unix_auth.so.1 #server_policy rsh auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other auth requisite pam_authtok_get.so.1 other auth required pam_dhkeys.so.1 other auth required pam_unix_cred.so.1 other auth sufficient pam_unix_auth.so.1 other auth sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass passwd auth required pam_passwd_auth.so.1 passwd auth sufficient pam_unix_auth.so.1 ssh account sufficient pam_unix.so.1 ssh account sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other account requisite pam_roles.so.1 other account sufficient pam_unix_account.so.1 other account sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass other password required pam_dhkeys.so.1 other password requisite pam_authtok_get.so.1 other password requisite pam_authtok_check.so.1 other password required pam_authtok_store.so.1 other password sufficient pam_unix.so.1 other password sufficient /usr/lib/security/pam_ldap.so.1 try_first_pass Local Authentication Works But LDAP Authentication Doesn't Work.

  Read the article

• Setting up Squid -> VPN connection

  - by Nedlinin

  I recently purchased a VPS and am wanting to use it as a VPN server. However, it has bandwidth limitations. So, I figured since I already have a local Squid proxy caching things for me, I could have users connect to the proxy and the proxy connect to the VPN. Then when someone hits the web, Squid will serve it from cache if available and, if not, it will use the VPN to download it. My issue is, I have no idea how to set this up :p - Essentially I want Machine - Squid - VPN. My VPN is running on Ubuntu Server with pptpd. Squid is running on a local Arch Linux box. Squid and the VPN are both working perfectly independently. Any help on how to have Squid push traffic through the VPN would be greatly appreciated! Also: I don't actually want to use the VPN for all traffic. Otherwise, I'd just connect my router to the VPN and be happy. I only want to use it for web traffic from specific machines on the network.

  Read the article

• How do I install PHP 5.3 on CentOS?

  - by fivelitresofsoda

  I have to install PHP 5.3 on my CentOS server. If I do yum install php, the base repository installs 5.1.6 which is too old for the applications I need to install. So I've been trying to use the IUS repository, following the official instructions from IUS: root@linuxbox ~]# wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-2.ius.el5.noarch.rpm root@linuxbox ~]# wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm root@linuxbox ~]# rpm -Uvh ius-release*.rpm epel-release*.rpm OK. Now I simply do yum install php53, etc. for all I need... but I get this error: Running rpm_check_debug Running Transaction Test Finished Transaction Test Transaction Check Error: file /usr/bin/php from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /usr/bin/php-cgi from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /usr/share/man/man1/php.1.gz from install of php53u-cli-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-cli-5.1.6-27.el5_5.3.x86_64 file /etc/php.ini from install of php53u-common-5.3.4-3.ius.el5.x86_64 conflicts with file from package php-common-5.1.6-27.el5_5.3.x86_64 Error Summary ------------- I have no idea on how to solve this. I think I have to delete the base packages. However, as someone new to Linux, I don't know how to do that.

  Read the article

• Which Firefox add-on is responsible for a rendering bug?

  - by Gilles

  I've found a page that isn't rendered correctly by Firefox with my usual profile. It is rendered correctly with a blank profile. I have quite a few add-ons. One of them is surely the culprit. How can I find out which? Userscripts often affect the rendering. But I turned off Greasemonkey, and it didn't help. So it's something else, presumably an extension (what else could it be? I have no chrome/userChrome.css.). I'm looking for an easy way to find out which one, easier than disabling a bunch of extensions and restarting umpteen times. Related: Create a tool to help users identify a problematic add-on by bisecting the list of installed add-ons — a similar problem which would admit a similar solution. I want to automate this as much as possible; something like git bisect, that doesn't require me to change my actual profile, would be ideal. A Linux-specific solution is fine with me.

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• What is optimal hardware configuration for heavy load LAMP application

  - by Piotr K.

  I need to run Linux-Apache-PHP-MySQL application (Moodle e-learning platform) for a large number of concurrent users - I am aiming 5000 users. By concurrent I mean that 5000 people should be able to work with the application at the same time. "Work" means not only do database reads but writes as well. The application is not very typical, since it is doing a lot of inserts/updates on the database, so caching techniques are not helping to much. We are using InnoDB storage engine. In addition application is not written with performance in mind. For instance one Apache thread usually occupies about 30-50 MB of RAM. I would be greatful for information what hardware is needed to build scalable configuration that is able to handle this kind of load. We are using right now two HP DLG 380 with two 4 core processors which are able to handle much lower load (typically 300-500 concurrent users). Is it reasonable to invest in this kind of boxes and build cluster using them or is it better to go with some more high-end hardware? I am particularly curious how many and how powerful servers are needed (number of processors/cores, size of RAM) what network equipment should be used (what kind of switches, network cards) any other hardware, like particular disc storage solutions, etc, that are needed Another thing is how to put together everything, that is what is the most optimal architecture. Clustering with MySQL is rather hard (people are complaining about MySQL Cluster, even here on Stackoverflow).

  Read the article

• A separate user for each task?

  - by Mark Tomlin

  I just got a VPS sver the other day, I'm new to server administration, but not that new to Ubuntu (11.04). I use it in my living room as the HTPC, and I had a previous VPS that I used on and off for a team speak server. This one I'm setting up for long term use. So I would like to know the best practice when it comes to websites and tasks that I have the server proforming. I understand that it could be beneficial to separate each website into it's own usergroup or under its own username. I would setup nginx so that it could read all of the users directors (and thus each website) but could not touch anything else. The same with the TeamSpeak, should I make a user for TeamSpeak so that it operates within its own confined area or is this overkill? I do have access to root on the sever and my current plan is to run about 4 websites and a TeamSpeak server. My stack is Linux (Ubuntu 11.04 LTS), nginx, and PHP 5.4.3 (using the PDO SQLite 3 built in driver for the database). Should PHP have it's own user group or is it ok to place it in with nginx?

  Read the article

• cups log kills ubuntu 12.04 and sudoer permissions changed

  - by peterretief

  I am using Ubuntu 12.04 as a desktop and recently had a weird crash with the log file for cups filling up the entire drive and not letting me back in, also what changed was /var/lib/sudo had changed from root to peter (me) I didn't make this change - I checked the history! I set the sudoers back to root and capped the max size for cups log Anyone had a similar experience? It feels like someone is messing around with my settings Is there any way to trace how the error occurred? Logs auth.log Jan 1 02:04:13 peter-desktop lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) Jan 1 02:04:13 peter-desktop lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 Jan 1 02:06:53 peter-desktop lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) Jan 1 02:06:53 peter-desktop lightdm: pam_ck_connector(lightdm:session): nox11 mode, ignoring PAM_TTY :0 syslog Jan 1 02:04:13 peter-desktop rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="903" x-info="http://www.rsyslog.com"] start Jan 1 02:04:13 peter-desktop rsyslogd: rsyslogd's groupid changed to 103 Jan 1 02:04:13 peter-desktop rsyslogd: rsyslogd's userid changed to 101 Jan 1 02:04:13 peter-desktop rsyslogd-2039: Could not open output pipe '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] Jan 1 02:04:13 peter-desktop bluetoothd[898]: Failed to init gatt_example plugin Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Initializing cgroup subsys cpuset Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Initializing cgroup subsys cpu Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Linux version 3.2.0-25-generic-pae (buildd@palmer) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #40-Ubuntu SMP Wed May 23 22:11:24 UTC 2012 (Ubuntu 3.2.0-25.40-generic-pae 3.2.18) Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] KERNEL supported cpus: Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] Intel GenuineIntel Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] AMD AuthenticAMD Jan 1 02:04:13 peter-desktop kernel: [ 0.000000] NSC Geode by NSC

  Read the article

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• What benchmark tool to use to benchmark hardware for VM server?

  - by Mark0978

  We are setting up a new piece of hardware to virtualize several of our servers on. Choices are RAID 5, RAID 6, and RAID 0+1. We are wanting to benchmark all three before we go live with the machine, but I'm not sure how to test the speed. Since we will be using it to host VMs, what will the actual disk traffic look like? What can I use to see if RAID 6 is too slow? Short of setting up the system with all the VM's on it and running that way, then redoing on all the work, I'm not sure how to test it. It them becomes more of a subjective test than an objective one. I'm worried that RAID6 will have too much overhead, that RAID5 will be to fragile with 3TB drives and I've never worked with 0+1 at all. So in short I'd like to setup the base machine (which will be running Linux) and then test the underlying SW RAID for speed. What kind of tool exists to simulate this kind of load? Barring the lack of a specific tool, how about a generic FS testing tool that will simulate different loads?

  Read the article

• Jboss unreachable/ slow behind apache with ajp

  - by Niels

  I have an linux server running with a JBoss Instance with apache2. Apache2 will use AJP connection to reverse proxy to JBoss. I found these messages in the apache error.log: [error] (70007)The timeout specified has expired: ajp_ilink_receive() can't receive header [error] ajp_read_header: ajp_ilink_receive failed [error] (120006)APR does not understand this error code: proxy: read response failed from 8.8.8.8:8009 (hostname) [error] (111)Connection refused: proxy: AJP: attempt to connect to 8.8.8.8:8009 (hostname) failed [error] ap_proxy_connect_backend disabling worker for (hostname) [error] proxy: AJP: failed to make connection to backend: hostname [error] proxy: AJP: disabled connection for (hostname)25 I googled around but I can't seem to find any related topics. There are people say this behavior can be caused by misconfigured apache vs jboss. Telling the max amount of connections apache allows are far greater then jboss, causing the apache connection to time out. But I know the app isn't used by thousands of simultaneous connections at the time not even hundreds of connections so I don't believe this could be a cause. Does anybody have an idea? Or could tell me how to debug this problem? I'm using these versions: Debian 4.3.5-4 64Bit Apache Version 2.2.16 JBOSS Version 4.2.3.GA Thanks

  Read the article

• On a failing hard drive, I am able to view data but unable to copy it - why?

  - by Tom

  I have a 2.5" external hard drive that is failing. It's not making the expected 'clicking' noise that most hard drives and I am able to view the data, but I am unable to actually retrieve the data. I attempted to use SpinRite in order to access the data on the drive, but it didn't like the external drive. When I view the drive's property page, the drive shows that it's used space is at 100% and that it has 0 bytes available; however, the progress indicator under the drive icon in Windows Explorer shows that it's roughly 50% full (which is correct). When I attempt to run Windows' "Error Checking" tool and attempt to "scan for an attempt recovery of bad sectors," the tool begins to run then immediately closes with no error message. I am able to browse the contents of the drive using Windows Explorer. When I begin to try copying any given single file, the copy process begins, an indicator starts, and then the copy fails with no real error message. The Disk Management page in Computer Management under Control Panel also shows this drive has being 'Healthy.' I dropped the drive off at a data recovery store and they said that "The data seems to be intact, but an internal failure is preventing any information from being retrieved." They offered to provide me references to a data recovery specialist. I've also attempted to run CHKDSK on the drive (with and without arguments) but it returns the following error: The type of the filesystem is RAW. CHKDSK is not available for RAW drives. Before going the route of more expensive data recovery, I'm wondering if these symptoms sound familiar to anyone? Other questions... I'm willing to continue trying tools such as TestDisk and/or PhotoRec (as the majority of the data that I'd like to salvage are photos) but how long I should expect either tool to run given approximately 400GB of data? I'm also comfortable using Linux so I welcome any suggestions for utilities or tools and strategies with which you've had success.

  Read the article

< Previous Page | 906 907 908 909 910 911 912 913 914 915 916 917  | Next Page >