Search Results

Search found 3171 results on 127 pages for 'manual manuel'.

Page 92/127 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• Network Load Balancing and AnyCast Routing

  - by user126917

  Hi All can anyone advise on problems with the following? I am planning on installing the following setup on my estate: I have 2 sites that both have a large amount of users. Goals are to keep things simple for the users and to have automatic failover above the database level. Our Database will exist at the primary site and be async mirrored to the secondary site with manual failover procedures.The database generate sequential ID's so distributing it is not an option. I plan to site IIS boxes at both sites with all of the business logic on them and heavy operations. The connections to SQL will be lightweight and DB reads will be cached on IIS. On this layer I plan to use Windows network load balancing and have the same IP or IPs across all IIS boxes at both sites. This way there will be automatic failover and no single point of failure. Also users can have one web address regardless of which site they are in automatically be network load balanced to their local IIS. This is great but obviously our two sites are on different subnets and as this will be one IP address with most of our traffic we can't go broadcasting everything across the link between the sites. To solve this problem we plan to use AnyCast routing over our network layer to route the traffic to the most local box that is listening which will be defined by the network load balancing. Has anyone used this setup before? Can anyone think of any issues with this? Also some specifics I can't find anywhere at the moment. If my Windows box is assigned an IP and listening on that IP but network load balancing is not accepting specific traffic then will AnyCast route away from that? Also can I AnyCast on a socket level?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• BackupExec 2012 File System Archiving - Access is denied to Remote Agent

  - by AllisZero

  Gentlemen, I've been struggling with a Trial version of Symantec Backup Exec 2012 for about a week now. It was installed as an upgrade to our 12.5 license, and the setup completed with no issues. The reason I upgraded is solely for the File System Archiving option as I'm working to reduce the amount of live data in my servers. Backups work A-Ok and I have followed the instructions in the Admin Manual to make sure I had filled all requirements. The account BE is running under is a member of the Local administrators group as required and has been added to the test share that I'm using to evaluate the archiving function. Testing the credentials in the job setup window always works fine, and I am able to add both regular and Admin$ shares to my Archive selection. However, every time I run the Archive job, I get the following message: https://dl.dropbox.com/u/59540229/BEXec.png I've already tried to troubleshoot DNS resolution issues as suggested in the Symantec KB to no avail. The only thing I can think of, at this point, is that a trial license doesn't allow me to use the Archiving function, although that would seem silly on their part. Appreciate any assistance or information. Thanks.

  Read the article

• Moving the Windows 7 Pro OEM image to computer with the same hardware

  - by SWin

  We bought 8 clean computers (even without HDD) with the same hardware and bought eight Windows 7 Pro OEM disks. Now I prepare one Win7 installation without activation but with all required programs, settings, etc. Then I'm going to clone the image to other computers even without sysprepping. I'm going to change the product key to legal number at COA sticker on each computer and make the activation through the Internet. Will this scenario work? I know that OEM's license agreement forbids the image cloning and the actions I'm going to do breaks the agreement. According the license agreement I should make the manual clean install of Win7 on each computer. But how Microsoft and other viewers can determine the cloning fact? All computers are the same and license Win7 DVDs are also the same. However in my case the installation time also will the same (and may be kind of installation code or something else) and this is not good. Will the Win7 activation work? Can I be sure that activation will not damage after some time? Can Microsoft determine the cloning fact during the activation process? Thank you.

  Read the article

• Create a wifi hotspot in a place where an authentication is required

  - by SoftTimur

  I live in a residence where Internet is provided via cable. Once the computer is connected to the cable, launching a browser will trigger an authentication, I have a username and password to enter, then the internet will be connected. With a gateway (e.g. Wireless Cable Voice Gateway Model CBVG834G) and 2 cables, two PCs can connect to the Internet with my account at the same time. Now the question is, I don't like the cable, and would like to create a wifi hotspot. It seems realizable with the same gateway. According to the instruction on page 2-4 of the manual: Enter http://192.168.0.1 in the address field of your Internet browser. Log in to the gateway with either of the default user names, MSO or admin... However, while connecting to the Internet successfully via cable and the gateway (e.g. google works), opening 192.168.0.1 oddly gives me an error on the browser: Does anyone know what happened? Is it due to the authentication required by my residence? Is there any other way to build a hotspot of wifi? PS: My system is MAC OS

  Read the article

• compile ntp without ssl

  - by Zulakis

  I need to deploy ntp to a very space-critical pxe-imaging-system. (Yes, each KB matters.) Footprint needs to be as small as possible, so I want to compile ntp without linking openssl. According to the manual this is should be possible: If available, the OpenSSL library from http://www.openssl.org is used to support public key cryptography. The library must be built and installed prior to building NTP. The procedures for doing that are included in the OpenSSL documentation. The library is found during the normal NTP configure phase and the interface routines compiled automatically. Only the libcrypto.a library file and openssl header files are needed. If the library is not available or disabled, this step is not required. I already tried out ./configure --without-openssl however, this didn't help. This is my ldd output: ldd ntpd/ntpd linux-gate.so.1 => (0xb7706000) libm.so.6 => /lib/i686/cmov/libm.so.6 (0xb76d5000) libcrypto.so.0.9.8 => /usr/lib/i686/cmov/libcrypto.so.0.9.8 (0xb7582000) librt.so.1 => /lib/i686/cmov/librt.so.1 (0xb7578000) libc.so.6 => /lib/i686/cmov/libc.so.6 (0xb741d000) /lib/ld-linux.so.2 (0xb7707000) libdl.so.2 => /lib/i686/cmov/libdl.so.2 (0xb7419000) libz.so.1 => /usr/lib/libz.so.1 (0xb7404000) libpthread.so.0 => /lib/i686/cmov/libpthread.so.0 (0xb73eb000) The system I am compiling on is 32-bit debian lenny using openssl 0.9.8g-15+lenny16. What is the correct configure option to compile ntp without openssl?

  Read the article

• VGA to S-Video/Video converter showing mashed up picture.

  - by Matthijs Wessels

  Earlier I asked this question: *http://superuser.com/questions/132374/does-the-lenovo-t60p-vga-port-support-an-s-video-signal As a result I acquired the following item: http://cgi.ebay.nl/ws/eBayISAPI.dll?ViewItem&item=250588098582&ssPageName=ADME:B:EOIBSA:NL:1123 Yea I'm a cheapass... Anyway, it just arrived and now I am trying to get it to work... The manual is not very informative other than telling me, this is the vga in, this is the vga out, this is the s/video out etc. Plus it tells me the system should support the following resolutions@refresh rate: 640x480@60/72/75Hz 800x600@60/75Hz 1024x768@60Hz I can connect it to my laptop and then I connect the S/Video and the Video to my tv which only gives me a blurred image (like when you set your monitor to a resolution it doesn't support). The VGA out however works fine to my tft monitor. The are two switches on the converter. I think one switches between s/video and video and the other between PAL and NTSC. But alas, no combination seems to give a better picture (it does give a different picture). Can anyone help me to solve this problem? I have downloaded this program called powerstrip, but I have no idea how to use it and if it can even solve my problem... Thanks in advance. I use Windows XP on a Lenovo t60p and I try to connect it to a Philips 32PFL7403D/12 LCD TV from VGA to a converter to S-video or video.

  Read the article

• how to setup a bridge with 2 NICs and few virtual machines

  - by Bond

  Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

  Read the article

• Running multiple copies of openssh-server (sshd) on Ubuntu

  - by cecilkorik

  I may be attacking this problem the wrong way, if so let me know. I have a server which is available through SSH from both the public internet and the local LAN. I would like to have two very different security policies for each, by running two copies of sshd with two different sshd_config files each on a different port. Some of the things I'd like to change is to allow password or public-key authentication on the LAN, but public-key only from the internet. All (real) users could login from the LAN side, but only certain authorized users would be individually whitelisted to login through the internet. As far as I can tell this requires having two different SSH daemons running on different ports with different sshd_configs. I am fine with the different ports part, I can easily forward port 22 to any port I want through my firewall. So my question is what is the best way to actually START the second sshd under Ubuntu 10.04 LTS. Is there a recommended way to do something like this? Surely I am not the first person with this sort of need. I have a bit of experience with upstart, and I can manually hack the second sshd into /etc/init/ssh.conf I suppose but I'm not sure if that will get overwritten by the package. However I do it, It's important to ensure both sshd processes always get restarted after any automatic or manual upgrade of the openssh-server package. Thanks in advance.

  Read the article

• Creating a pseudoterminal to make sudo happy

  - by larsks

  I need to automate the provisioning of a cloud instance (running Fedora 17) for which the following initial facts are true: I have ssh-key based access to a remote user (cloud) That user has password-free root access via sudo. Manual configuration is as simple as logging in and running sudo su - and having at it, but I would like to fully automate this process. The trick is that the system defaults to having the requiretty option enabled for sudo, which means that an attempt to do something like this: ssh remotehost sudo yum -y install puppet Will fail: sudo: sorry, you must have a tty to run sudo I am working around this right now by first pushing over a small Python script that will run a command on a pseudoterminal: import os import sys import errno import subprocess pid, master_fd = os.forkpty() if pid == 0: # child process: now that we're attached to a # pty, run the given command. os.execvp(sys.argv[1], sys.argv[1:]) else: while True: try: data = os.read(master_fd, 1024) except OSError, detail: if detail.errno == errno.EIO: break if not data: break sys.stdout.write(data) os.wait() Assuming that this is named pty, I can then run: ssh remotehost ./pty sudo yum -y install puppet This works fine, but I'm wondering if there are solutions already available that I haven't considered. I would normally think about expect, but it's not installed by default on this system. screen can do this in a pinch, but the best I came up with was: screen -dmS sudo somecommand ...which does work but eats the output. Are there any other tools available that will allocate a pseudoterminal for me that are going to be generally available?

  Read the article

• On Windows 2008 R2, how do I back up DHCP if the DHCP .mdb database is always busy?

  - by johnny

  I get this from my backup software. C:\WINDOWS\system32\dhcp\dhcp.mdb : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\j50.log : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\j50tmp.log : The process cannot access the file because it is being used by another process. C:\WINDOWS\system32\dhcp\tmp.edb : The process cannot access the file because it is being used by another process. My questions: Should I be doing a manual backup of DHCP via command line tools or maybe with MMC, Action, Backup before I run my backup? Is the %SystemRoot%\System32\DHCP\Backup directory always kept up to date? (which does get backed up by backup software) I'm answering my own question but the registry key is set up for 3c, 60 minutes, I believe. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\DHCPServer\Parameters\BackupInterva This is not the included backup software for Windows. It is another product, but I have seen this with every backup software I've ever used.

  Read the article

• AviSynth ChangeFPS: combining videos with different framerates

  - by Daniel Saner

  I have two video recordings of the same scene, but with different framerates, that I would like to combine using an AviSynth script. One video is recorded at 30fps, the other at 120fps. What I would like to do is to keep them temporally synchronised, meaning that for each frame of the 30fps video, the output should display 4 frames from the 120fps video. I would like the final output video to play at 30fps so that the duration is 4 times the original recordings. From AviSynth's documentation, it seems ChangeFPS is the function I'll need, since it removes and duplicates frames, while 'AssumeFPS' just changes the playback speed (and my plan is basically to quadruple every frame of the 30fps clip). However, the filter does not seem to do what it says. If I try: clip30 = AviSource("0326.avi").ChangeFPS(120) clip120 = AviSource("0326-120fps.avi") it doesn't affect the playback speed or frame count of the 30fps clip at all, but removes every fourth frame from the 120fps clip, which is not at all what I want. Unfortunately, appending .ChangeFPS(7.5) to the clip120 instead does not have the same inverse effect—in that case, it does exactly what's to be expected. Alternatively, if I try: clip30 = AviSource("0326.avi").AssumeFPS(7.5) clip120 = AviSource("0326-120fps.avi") there is no effect at all, both clips are played back at 30fps, meaning that only a quarter of the 120fps clip has been shown by the time the 30fps clip is over. So how can I combine these two clips in the manner I want? I was unable to find any other internal or external filters that would help me do that. It seems to me that if ChangeFPS did what the manual says, it would be the right one for the job.

  Read the article

• Preventing h/w RAID cards from dropping slow JBOD disks

  - by Kevin

  I'm considering buying a used SAS h/w RAID card for externally attaching HDDs to an HP ProLiant I'm setting up. However, I only require RAID functionality on some of the drives. Theoretically it should be simple to JBOD the other drives, but some of them are inexpensive SATA disks and probably cannot have TLER disabled. I'd like to know, prior to actually ordering a RAID card, whether typically RAID cards would still enforce dropping of disks that do not respond within a few seconds, even if the disk is in a JBOD, and whether there is any way to disable this. Ideally it would be nice to be able to select certain SAS ports that will be pass-through, bypassing the RAID engine entirely and just acting as an HBA for those ports. I know I could buy a separate SAS HBA but that seems like a waste of $ and is also impractical as it's a 1U server so space is extremely limited. My question then is whether the functionality I'm looking for (pass-through on certain ports or at least JBOD drives not getting themselves dropped due to slow response) is typical of proper h/w RAID cards such as PERC 5/E etc. I've browsed through the latter's manual but unfortunately, as with most user manuals, it states the obvious and doesn't state the unobvious. Thanks for any info, Kevin

  Read the article

• Drupal 7: One-time user account

  - by Noob

  I'm going to create a survey in Drupal 7 with the webform module, installed on a debian system which may be adapted in every way. The users (personally known, approx. 120) doing that survey will walk into a room and complete the survey in browsers on different computers. After that, they'll leave the room and other persons will enter, complete the survey on the same computers and so on. Each user may enter only one submission. The process needs to be anonymous, i. e. I mustn't have any idea of who did wich submission. My current solution is to generate random one-time-passwords and hand out one password per user (without noting who got which password). Within the survey there will be a password field where the one-time-password is entered. The value is checked by webform to be unique. I'll get the data via csv or Excel and verify the passwords manually in excel by comparing them to the list of valid passwords. The problem is: I don't like the idea of manually generating the password list, copying it to excel and doing a manual check. That's a good idea for one-time-use, but we're going to repeat the survey every once in a while. I'd rather generate one-time-logins (like user0001/fdlkjewf, user0002/dfrefnnr, ...) for each survey, hand them out to the users and let drupal/debian/whatever check whether a submission is valid or not. Do you have any idea how to batch-generate about 120 users with one-time-passwords in Drupal 7 and verify that each user may submit the form only once? Do you even have a better idea how to accomplish the task within the intranet? Thank you for your help.

  Read the article

• SSL connection error for only one site (of many) on server

  - by Matt Lacey

  I have a server running many websites, each with SSL. One of the sites is now refusing connections over SSL. This was previously working and I'm looking for assistance in determining what has been changed. Here's the situation: http://site1.com/ - works https://site1.com/ - works http://site2.com/ - works https://site2.com/ - Doesn't work (but did previously) Both sites are on the same server (Win Server 2003 SP2 - IIS6) Both sites use certificates from the same authority and are both valid (according to IIS). As far as I can tell, both sites have certificates configured identically in IIS. (Checked by a manual/visual check of properties, side by side) Through use of OpenSSL I can see that there's a "ssl handshake failure" when trying to connect to site2 using https. What could be the cause of this? How can I investigate further? Without SSL connections being available to this site, users are unable to log in or register. :( disclaimer: I'm not a server admin and not responsible for the box. Yes, there are wider issues here but I need to get this working again first.

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Shared configuration for Eclipse on Debian server

  - by Joris Meys

  I've manually installed the latest Eclipse on our debian server and wanted to configure it so all users share the same configuration. It turned out less obvious than I thought: I don't seem to be able to install packages for all users. If I run it myself, all configuration data is saved under my own home directory. If I run Eclipse using sudo, everything is saved under the root directory but is not accessible for other users when they run Eclipse. I've been browsing the manual of Eclipse and some forums, but apart from a "yes, you can" I couldn't find any information on how that should be done. The biggest problem is installing plugins for all users to be found. Any help is greatly appreciated. Eclipse : 3.6.1 classic, installed using this procedure. Server uname: GNU/Linux * 2.6.26-2-amd64 Server is accessed using Putty, and Gnome desktop through realVNC. Just mentioning it if that is of any importance. Our sysadmin is on "prolonged leave" (working in Spain and never replaced), so I'm stuck without help here. EDIT : -- I asked this question also on StackOverflow as I wasn't certain this is a genuine server-related question. Please feel free to merge both questions at the appropriate place. --

  Read the article

• Getting Win32_Service security descriptor using VBScript

  - by invictus

  Hi, I am using VbScript for retrieving the securitydescriptor of a Win32_Service. I am using the following code: SE_DACL_PRESENT = &h4 ACCESS_ALLOWED_ACE_TYPE = &h0 ACCESS_DENIED_ACE_TYPE = &h1 strComputer = "." Set objWMIService = GetObject("winmgmts:" _ & "{impersonationLevel=impersonate, (Security)}!\\" & strComputer & "\root\cimv2") Set colInstalledPrinters = objWMIService.ExecQuery _ ("Select * from Win32_Service") For Each objPrinter in colInstalledPrinters Wscript.Echo "Name: " & objPrinter.Name ' Get security descriptor for printer Return = objPrinter.GetSecurityDescriptor( objSD ) If ( return <> 0 ) Then WScript.Echo "Could not get security descriptor: " & Return wscript.Quit Return End If ' Extract the security descriptor flags intControlFlags = objSD.ControlFlags If intControlFlags AND SE_DACL_PRESENT Then ' Get the ACE entries from security descriptor colACEs = objSD.DACL For Each objACE in colACEs ' Get all the trustees and determine which have access to printer WScript.Echo objACE.Trustee.Domain & "\" & objACE.Trustee.Name If objACE.AceType = ACCESS_ALLOWED_ACE_TYPE Then WScript.Echo vbTab & "User has access to printer" ElseIf objACE.AceType = ACCESS_DENIED_ACE_TYPE Then WScript.Echo vbTab & "User does not have access to the printer" End If Next Else WScript.Echo "No DACL found in security descriptor" End If Next However, every time I run it I get the message saying the resulting code is -2165236532 something, rather than the error codes defined in the manual. Anyone got any ideas? I am using Windows 7 professional.

  Read the article

• Pivot table not refreshing sort order

  - by William Anthony

  I have Pivot Table that get its data source from another sheet, same workbook. I want the sort order of data is same as the data source order, I choose "Sort in data source order" in Pivot Table option. The problem is, when I change the data order on data source worksheet, then I refresh the Pivot Table, the sort order didn't change. I googled that the Pivot Table should be unlink first then re-link again in order to work properly, so I tried the following: The original data source has named range: origdata. The fake data source has names range: dummydata I changed manually data source to dummydata then changed back to origdata. The sort order did change as expected. Now I want to make the operation automated, so I'm using this code in Worksheet.activate event. Note that, PT is PivotTable instance. ... PT.SourceData = "dummydata" PT.RefreshTable PT.SourceData = "origdata" PT.RefreshTable ... Change data source from VBA didn't change the sort order just like I did with manual method. Why is that? Am I missing something? Maybe there are some routine called when I changed the data source manually via toolbar button? Thanks in advance for your help.

  Read the article

• MySQL ADO.NET Connector & MSSQL Integration Services

  - by user1114330

  Here I am, day three... attempting to sync a data view on a Windows Vista box (64 bit) running MSSQL 2012 and Visual Studio 2010. Sanity is slipping and hunger for progress fills my attention. I went through hell trying to get the MySQL ODBC drivers to get the job but to no avail...everyone seems to be lost and all the threads I can find are solutions that do not work for me. The problem: System DSN's not being seen by SSIS. SSIS DSN Not Showing as ODBC Data Source I make the decision to try out the ADO.NET connector...and to my surprise it is actually in the selection list in data sources in SSIS. So I take off running to create a Data Flow Task, create an ADO.NET Source (a local MSSQL DB)...all is good as usual. Then I move swiftly to creating a ADO.NET Destination, enter my credentials...wow, I am selecting a database finally on my linux server! Happy thinking that I finally have figured a way to get the job done. Then I move to mappings...nope, something is wrong...I am getting an error that hurts my eyes: Pipeline component has returned HRESULT error code 0xC0208457 from a a method call. Error at Data Flow Task [ADO NET Destination [81]]: Failed to get properties of external columns. The table name you entered may not exist or you do not have SELECT permission on the table object and an alternative attempt to get column properties through connection has failed. Detailed error messages are" You have an error in your SQL syntax check the manual that corresponds to your MySQL server version for the right syntax to use near "database".tablename" at line 1. The descriptor files on path C:\Program Files (x86)\Microsoft SQL Server\110\DTS\ProviderDescriptors\ does not contain schema information for connection of type MySQL.Data.MySqlClient.MySqlConnection. So it looks like it can't the information and therefore I cannot map the tables properly. Any ideas on this would be ultra helpful...thanks in advance to All!

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Backup Exec tape rotation guidelines

  - by HannesFostie

  Hi We use Backup Exec to take care of our backups for our data server, exchange server, and one more set of systems. Each of these 3 is being done on a separate "set" of tapes. Our goal is to be able to roll back a full 2 weeks, with 1 full backup each weekend and differential/incremental backups in between (the difference between the two in our case isn't very big, because the employees mostly use a very similar set of files throughout the week). While playing around with the settings on how to achieve this, we set the time for BE to keep the full backup to 14 days, but because we have too much data this would require manual intervention each time to erase a certain tape and use that. What I would like to know is what kind of guidelines, tricks, tips and general "stuff to think about" you keep in mind when designing your backup schedule. The type of backups (full/diff/incr) isn't of that much importance in our case as it's more or less set in stone. Made this community wiki as it's not a very specific question. Thanks in advance!

  Read the article

• Wireless router setup for 1-1 NAT

  - by Carlos

  What I have: A linksys router WAG160N with firmware version 2 A "pool" of 5 external static IP's provided by my ISP 213.xx.xxx.n All the required configuration values for the static IPs such as (Subnet Mask, Gateway and static DNS 1, 2, 3) Current WAN Configuration: Encapsulation: RFC 2364 PPPoA Multiplexing: VC QoS type: UBR DSL modulation: MultiMode What's connected to the network: 1 x Server (That I want to make available to the outside) 5 x Desktops with static internal IP's, such as 192.168.0.xx 2 x Network printers, also with internal static IP's 2 x Laptops 1 x NAS (Network Attached Storage) also on static IP What I want to do: I would like to make the server available from outside the network, for example from your house. The problem is that Im not really sure how to do this. I have tried following the steps on the instruction manual in Linksys but they do not seem to work, once I set it up as shown bellow, I loose internet and all hell breaks loose. Going into further detail, I would prefer if the network is changed as little as possible, by this I mean that all the computers stay networked within eachother and only the server is accessible from the outside the network. What I need HELP with: I have read around that it is possible to set a 1-1 NAT (I know where it is in the menu but have no clue what it does...) so that I can NAT a single public IP directly to a single private IP (in our case the server). But please, How do I do that? Or maybe an alternative?

  Read the article

• Production deployment to EC2 with minimal downtime

  - by jensendarren

  I have a simple web application deployed on a large instance with EC2. I now want to deploy the latest code to this server but I want to do this in a way which minimizes downtime and is a smooth as possible for the end user. Here is my plan: Fire up another large instance Install all the software layers on that instance Restore and attach an EBS drive to the instance Deploy our latest production ready code on the new instance Run all tests (including manual testing of the application) (If tests pass) Put a "Site Under Maintenance" notice on the live site. Backup the EBS instance on the live site Detach the EBS instance from the new server and replace with the latest backup Use ec2-associate-address to move the IP address to the new instance Sit back and wait for traffic to start flowing though the new instance Terminate the old instance Does this seem like a good strategy? Are there any tutorials or books that might cover this topic? I have already read Cloud Application Architectures by George Reese, which is an excellent book, but does not cover deployment. Additionally, I know that there are tools that can help with this like RightScale or enStratus which I will use when I start using more than one instance.

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >