Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 92/1617 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• PPPD Is Locking the Modem and Not Releasing It

  - by Skid

  Got an issue with PPPD on one of our system, we have a PC that is used to talk to remote sites via a dial up connection, the modem can both connect out to the sites and the sites also dial back in. Currently I'm having an issue where some times a site ether dials in or we dial out, and it connects, but then blocks the modem and throws and error to kern.log. Aug 26 14:23:57 TM-SCADA kernel: [191233.503745] INFO: task pppd:8142 blocked for more than 120 seconds. Aug 26 14:23:57 TM-SCADA kernel: [191233.503750] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 26 14:23:57 TM-SCADA kernel: [191233.503753] pppd D ffffffff8180cb40 0 8142 1 0x00000000 Aug 26 14:23:57 TM-SCADA kernel: [191233.503759] ffff8800ac1f5dc8 0000000000000086 ffff8800ac1f5fd8 00000000000137c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503765] ffff8800ac1f4010 00000000000137c0 00000000000137c0 00000000000137c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503770] ffff8800ac1f5fd8 00000000000137c0 ffffffff81c13020 ffff880135df5b80 Aug 26 14:23:57 TM-SCADA kernel: [191233.503775] Call Trace: Aug 26 14:23:57 TM-SCADA kernel: [191233.503784] [<ffffffff8166ba29>] schedule+0x29/0x70 Aug 26 14:23:57 TM-SCADA kernel: [191233.503790] [<ffffffff813db005>] tty_ldisc_ref_wait+0x65/0xb0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503796] [<ffffffff813f3061>] ? uart_ioctl+0xd1/0x1c0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503801] [<ffffffff81076960>] ? wake_up_bit+0x40/0x40 Aug 26 14:23:57 TM-SCADA kernel: [191233.503806] [<ffffffff813d3fa0>] tty_ioctl+0x2c0/0x9a0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503810] [<ffffffff811d0549>] ? fcntl_setlk+0x69/0x200 Aug 26 14:23:57 TM-SCADA kernel: [191233.503815] [<ffffffff81195f79>] do_vfs_ioctl+0x99/0x330 Aug 26 14:23:57 TM-SCADA kernel: [191233.503820] [<ffffffff81195212>] ? do_fcntl+0x232/0x410 Aug 26 14:23:57 TM-SCADA kernel: [191233.503823] [<ffffffff811962b1>] sys_ioctl+0xa1/0xb0 Aug 26 14:23:57 TM-SCADA kernel: [191233.503829] [<ffffffff81674e69>] system_call_fastpath+0x16/0x1b The syslog trace stops at "Serial connection established". Aug 28 06:00:03 TM-SCADA pppd[10358]: pppd 2.4.5 started by root, uid 0 Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO CARRIER) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO DIALTONE) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (ERROR) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (NO ANSWER) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (BUSY) Aug 28 06:00:04 TM-SCADA chat[10360]: abort on (Username/Password Incorrect) Aug 28 06:00:04 TM-SCADA chat[10360]: send (atz^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (OK) Aug 28 06:00:04 TM-SCADA chat[10360]: atz^M^M Aug 28 06:00:04 TM-SCADA chat[10360]: OK Aug 28 06:00:04 TM-SCADA chat[10360]: -- got it Aug 28 06:00:04 TM-SCADA chat[10360]: send (atx0^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (OK) Aug 28 06:00:04 TM-SCADA chat[10360]: ^M Aug 28 06:00:04 TM-SCADA chat[10360]: atx0^M^M Aug 28 06:00:04 TM-SCADA chat[10360]: OK Aug 28 06:00:04 TM-SCADA chat[10360]: -- got it Aug 28 06:00:04 TM-SCADA chat[10360]: send (atdt0123456789^M) Aug 28 06:00:04 TM-SCADA chat[10360]: expect (CONNECT/ARQ) Aug 28 06:00:04 TM-SCADA chat[10360]: ^M Aug 28 06:00:30 TM-SCADA chat[10360]: atdt0123456789^M^M Aug 28 06:00:30 TM-SCADA chat[10360]: CONNECT/ARQ Aug 28 06:00:30 TM-SCADA chat[10360]: -- got it Aug 28 06:00:30 TM-SCADA pppd[10358]: Serial connection established. I've only found two ways to release the modem in this condition, the first is to turn the modem off and on again, the second is to delete the serial lock file, and then SIGKILL pppd. Now I could write into our software to do the latter if the modem is locked, but I would rather stop it from locking in the first place if at all possible. The reason I put this issue in the askubuntu is because we used to use OpenSuse and never had an issue with it, admittedly that was version 11.2 or earlier so its still and old kernel, but I figured I would ask here first anyway. Any suggestions of places to look would be appreciated.

  Read the article

• Suggestions on managing social media accounts

  - by Rob

  As a company we now have Facebook, LinkedIN, Twitter and now Google+, is there a way to easily manage all these accounts without having to log into them individually? Things like posting content to each one is becoming a full time job in itself, is there a way to post once that in turn posts to all other accounts? I used to use http://ping.fm/ a long time ago, has there been any advancements in something similar to this? With friend lists, news feeds etc etc for each one, I wish there was a way to manage them all in one place with a service/tool!

  Read the article

• Game Engine that allows for objects being placed in-game

  - by user185812

  I am looking for a game engine with multiplayer support that allows for players to place objects in the terrain. (eg. in TF2 one can place teleporters, etc...or in minecraft one can place blocks). I don't need the placeable objects to be interactive like in TF2, but I just need an engine that won't make me code this from scratch. I have decent knowledge of Python, PHP, HTML, C++ and C# (and a small knowledge of Lua scripting, although I have only been at it for a few months) so I should be able to handle most engines. So far I have looked at UDK and Cryengine, and wasn't thrilled with either.

  Read the article

• DSL PPPoE connection not working?

  - by Mussnoon

  I use a wired PPPoE connection to connect to the Internet. What I need to do on Windows to connect to it is put in static IP address, gateway, subnet mask and DNS servers for my LAN card. Next I have to create a dialer for a PPPoE connection, put in my user name, the service name and the password, and "dial" this connection. And it works fine. On Ubuntu 10.04, however, I have tried setting things up in a similar fashion - put in all static addresses for the "automatic" wired connection, then put in user name, service name, password for a "DSL" connection. It worked for a while, then stopped. I have tried putting in all the details within the DSL configuration dialog, same thing happened - it worked for a while, then stopped. I have tried deleting the ethernet connection and only keeping the DSL one with all the numbers put in place, same thing happened - it worked for a while, then stopped. Each of the times, when it connected, it connected randomly, after trying a few times, and either stopped working within a few minutes, or after I had rebooted. I have deleted and remade the connection dozens of times - even with different names, but nothing seems to be working. I have also tried pppoeconf from the terminal, didn't work. I have checked /var/log/kern.log, but nothing changes in the file when I try to connect. I have also checked /sbin/route, but gedit can't even open it (says it can't figure the character encoding...). The "connection established" notification pops up from the top right corner, the same way as when the computer is actually connected to a network. Can anyone figure what's wrong and how it can be solved?

  Read the article

• Making the Grade

  - by [email protected]

  Education Organizations Learn the Advantages of Oracle Today, K-12 school districts and state agencies nationwide have billions of reasons to come to Oracle OpenWorld 2010. Ever since the American Recovery and Reinvestment Act of 2009 set aside US$100 billion for education, schools have been eager to develop and implement statewide data systems to enhance workflow. And across the country, they've been turning to Oracle for help. According to a recent news release, Oracle already makes the grade. The Los Angeles Unified School District--the nation's second largest district--chose Oracle Business Intelligence Suite, Enterprise Edition Plus to help teachers keep track of student performance. Other educational organizations, including Fairfax County Public Schools and the North Carolina Department of Public Instruction, are also working with Oracle to improve their systemwide procedures. If you're an educator or administrator who is planning to optimize your school or agency data systems, this may be the best time to learn what Oracle can do help ensure success. Register for Oracle OpenWorld 2010 between now and July 16 and you'll save US$500 off registration.

  Read the article

• Drop and Give Me 20 Questions

  - by [email protected]

  IOUG Sponsors Boot Camp at Collaborate 10 Feeling flabby and out of shape on topics such as virtualization, SQL development, and security? Want to beef up your skills on Oracle Database 11g Release 2, Oracle on Linux for IBM System z, and Oracle's maximum availability architecture on Linux for IBM System z? If so, it's time for boot camp. The Independent Oracle Users Group (IOUG) is sponsoring its first-ever boot camp for Oracle technology and database professionals at Collaborate 10, April 19 to 21. And yes, as with many boot camps, the IOUG programs will be in a harsh, desert environment--at the Mandalay Bay Convention Center in Las Vegas, Nevada. The one- and two-day programs will cover Oracle technology and a variety of database topics, and they'll be taught by drill instructors, including industry experts as well as Oracle users and staff. You'll get in-depth training. But don't worry. You won't have to suffer through a bad haircut and 20-mile hikes. Are you ready? Was that a "yes, sir"? I can't hear you.

  Read the article

• Migration from one domain to another - Transfering the social media stats

  - by Dipak Saraf

  I am planning to move my site from one domain to another i.e from domain a.com to b.com . The site also has a lot of content and the migration of content is not an issue. The 301 redirect will take care of all the backlinks also. But my real worry is transfer the social media shares links and stats from domain a.com to b.com. I need some insight or any way in which the same can be migrated seamlessly from domain a.com to b.com

  Read the article

• How to sync the actions in a mutiplayer game?

  - by Wheeler

  I connect the clients with UDP (its a peer to peer connection on a multicast network) and the clients are sending their positions in every frame (in WP7 it means the default 30 FPS) to each other. This game is kinda a pong game, and my problem is the next: whenever the opponent hits the ball the angle will not be the same on both mobiles. I think its because the latency (1 pixel difference can cause a different angle). So my question is: how can I sync the hitting event?

  Read the article

• Connecting 2 ubuntu machines as a LAN

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue? Thank you ANSWERED All I had to do was set up both ip's maually, subnet mask to 255.255.255.0 and left blank both gateway and DNS.

  Read the article

• Cannot ping static ip on eth1

  - by Calvin Froedge

  I am trying to ping the network interface I have set up for eth1. This is my config: auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1 broadcast 192.168.1.255 If I ping 192.168.1.2, I get: Ping 192.168.1.2 (192.168.1.2) 56(84) bytes of data. From 192.168.1.3 icmp_seq=3 Destination Host Unreachable Results of ifconfig tell me that the IPv4 address is 192.168.1.3. I can ping this ip. Bcast and Mask are as expected (same as in definition). I can ping 192.168.1.3 from my macbook. I cannot ping 192.168.1.2 locally or from my macbook. Any ideas why?

  Read the article

• Library like ENet, but for TCP?

  - by Milo

  I'm not looking to use boost::asio, it is overly complex for my needs. I'm building a game that is cross platform, for desktop, iPhone and Android. I found a library called ENet which is pretty much what I need, but it uses UDP which does not seem to support encryption and a few other things. Given that the game is an event driven card game, TCP seems like the right fit. However, all I have found is WINSOCK / berkley sockets and bost::asio. Here is a sample client server application with ENet: #include <enet/enet.h> #include <stdlib.h> #include <string> #include <iostream> class Host { ENetAddress address; ENetHost * server; ENetHost* client; ENetEvent event; public: Host() :server(NULL) { enet_initialize(); setupServer(); } void setupServer() { if(server) { enet_host_destroy(server); server = NULL; } address.host = ENET_HOST_ANY; /* Bind the server to port 1234. */ address.port = 1721; server = enet_host_create (& address /* the address to bind the server host to */, 32 /* allow up to 32 clients and/or outgoing connections */, 2 /* allow up to 2 channels to be used, 0 and 1 */, 0 /* assume any amount of incoming bandwidth */, 0 /* assume any amount of outgoing bandwidth */); } void daLoop() { while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (server, & event, 5000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_CONNECT: printf ("A new client connected from %x:%u.\n", event.peer -> address.host, event.peer -> address.port); /* Store any relevant client information here. */ event.peer -> data = "Client information"; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("packet", strlen ("packet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("packetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("packet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (server); break; case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; case ENET_EVENT_TYPE_DISCONNECT: printf ("%s disconected.\n", event.peer -> data); /* Reset the peer's client information. */ event.peer -> data = NULL; } } } } ~Host() { if(server) { enet_host_destroy(server); server = NULL; } atexit (enet_deinitialize); } }; class Client { ENetAddress address; ENetEvent event; ENetPeer *peer; ENetHost* client; public: Client() :peer(NULL) { enet_initialize(); setupPeer(); } void setupPeer() { client = enet_host_create (NULL /* create a client host */, 1 /* only allow 1 outgoing connection */, 2 /* allow up 2 channels to be used, 0 and 1 */, 57600 / 8 /* 56K modem with 56 Kbps downstream bandwidth */, 14400 / 8 /* 56K modem with 14 Kbps upstream bandwidth */); if (client == NULL) { fprintf (stderr, "An error occurred while trying to create an ENet client host.\n"); exit (EXIT_FAILURE); } /* Connect to some.server.net:1234. */ enet_address_set_host (& address, "192.168.2.13"); address.port = 1721; /* Initiate the connection, allocating the two channels 0 and 1. */ peer = enet_host_connect (client, & address, 2, 0); if (peer == NULL) { fprintf (stderr, "No available peers for initiating an ENet connection.\n"); exit (EXIT_FAILURE); } /* Wait up to 5 seconds for the connection attempt to succeed. */ if (enet_host_service (client, & event, 20000) > 0 && event.type == ENET_EVENT_TYPE_CONNECT) { std::cout << "Connection to some.server.net:1234 succeeded." << std::endl; } else { /* Either the 5 seconds are up or a disconnect event was */ /* received. Reset the peer in the event the 5 seconds */ /* had run out without any significant event. */ enet_peer_reset (peer); puts ("Connection to some.server.net:1234 failed."); } } void daLoop() { ENetPacket* packet; /* Create a reliable packet of size 7 containing "packet\0" */ packet = enet_packet_create ("backet", strlen ("backet") + 1, ENET_PACKET_FLAG_RELIABLE); /* Extend the packet so and append the string "foo", so it now */ /* contains "packetfoo\0" */ enet_packet_resize (packet, strlen ("backetfoo") + 1); strcpy ((char*)& packet -> data [strlen ("backet")], "foo"); /* Send the packet to the peer over channel id 0. */ /* One could also broadcast the packet by */ /* enet_host_broadcast (host, 0, packet); */ enet_peer_send (event.peer, 0, packet); /* One could just use enet_host_service() instead. */ enet_host_flush (client); while(true) { /* Wait up to 1000 milliseconds for an event. */ while (enet_host_service (client, & event, 1000) > 0) { ENetPacket * packet; switch (event.type) { case ENET_EVENT_TYPE_RECEIVE: printf ("A packet of length %u containing %s was received from %s on channel %u.\n", event.packet -> dataLength, event.packet -> data, event.peer -> data, event.channelID); /* Clean up the packet now that we're done using it. */ enet_packet_destroy (event.packet); break; } } } } ~Client() { atexit (enet_deinitialize); } }; int main() { std::string a; std::cin >> a; if(a == "host") { Host host; host.daLoop(); } else { Client c; c.daLoop(); } return 0; } I looked at some socket tutorials and they seemed a bit too low level. I just need something that abstracts away the platform (eg, no WINSOCKS) and that has basic ability to keep track of connected clients and send them messages. Thanks

  Read the article

• Network connection delay after installing indicator-network

  - by Adrian

  Ok, so here's the thing,I installed wingpanel in UBUNTU 10.10, i removed the gnome-panels (yes, both). In the wingpanel itself there's no NETWORK indicator, so i google it and in some forums, some guy wrote that you have to install "indicator-network". I did it, and it solved the network indicator in the wingpanel, BUT now everytime i turn on my computer, the connection takes like 2 minutes or more to connect, when before installing this thing it did it immediately. How can i solve this? any help?

  Read the article

• Wow Twitter!!! Ten billions and counting

  - by samsudeen

  Twitter the micro blogging site crossed the ten billions milestone on 4th of this month as per the report by GigaTweet (Site which tracks the number of tweets posted on twitter) The person who sent the 10 billionth tweet is still unknown as his profile is protected. But the 9,999,999,999th tweet was sent by one Rafaela Marques from Brazil. AS you can see GigaTweet expects just another 196 days to reach the 20 billionth marks if tweet continues with the current pace. Some of the interesting statics about rate in which people tweeted every year 2007 – 5000 tweets per day 2008 – 300,000 tweets per day 2009 – 2.5 million per day It reached an average of 35 million tweets per day by end  2009. Today believe it or not the tweet rate is 50 million tweets per day and that’s why we call Wow Twitter!!! . Join us on Facebook to read all our stories right inside your Facebook news feed.

  Read the article

• Toshiba Satellite C850, Wlan, rtl8188ce not working

  - by Hans

  I installed Ubunto 12.04 onto a brand new Toshiba Satellite C850 64 bit laptop. Wlan does not work, Tries to connect, gives up after some time. $Windows7 works 100%. There appears to be a problem with the driver. The actual hardware is a rtl8188ce chip. The firmware & driver loaded by Ubunto is for the rtl8192ce chip. How can I get and install a driver and firmware for Ubunto 12.04 and rtl8188ce?

  Read the article

• Setting up SANED with sane-test

  - by Enoon

  I'm trying to setup a network service for running saned (running the sane-test backend) on Ubuntu 12.10, running it on a virtualbox. I followed the directions found here: https://help.ubuntu.com/community/ScanningHowTo and i got to the point where if i use a front-end like xsane, or use the command scanimage -d test i get the desired behaviour. (i get the test image). But when i try to use the network demon to access the backend (from the localhost) i get Failed to connect. I used telnet on 127.0.0.1 6566 and i got the following error: saned: symbol lookup error: saned: undefined symbol: sanei_w_init I'm a linux newbie, so i could be making some stupid mistake. Any ideas on how to fix this? Thanks [update]After posting this question i logged out, logged back in and it worked. After a few days i tried again and it gave the same error as before. Any help?

  Read the article

• Bridging: Loosing WLAN network connection with 4addr on option - Why?

  - by WitchCraft

  Question: For use with my Xen VM, I need to create a virtual network interface (vif) that is bridged to wlan0. If in /etc/network/interfaces I add auto xenbr0 iface xenbr0 inet dhcp And then later do brctl addif xenbr0 wlan0 I get this error message. can't add wlan0 to bridge xenbr0: Operation not supported I found out that Linux won't let you bridge a wireless interface in managed mode at all unless you enable the 4addr option (needed to recompile iw): iw dev wlan0 set 4addr on Afterwards brctl addif xenbr0 wlan0 works, and brctl show shows xenbr0 as bridged to wlan0. Unfortunately, as soon as I execute iw dev wlan0 set 4addr on my entire network connection is gone (no connection). As soon as then I execute iw dev wlan0 set 4addr off I reconnect and it works again. If I re-execute 4addr on, it breaks again, if I execute 4addr off, it works again. Unfortunately, I can't just turn 4addr on, activate the bridge and then turn it back off (error: device not ready). Does anybody know why I loose my connection ?

  Read the article

• Network Balancing Act

  - by listey

  Next up in our popular Oracle Solaris How To series is the Integrated Load Balancer, part of the suite of network facilities that are built in to Oracle Solaris 11. Providing Layer 3 and Layer 4 load balancing capabilities you can use this device to simulate or even replace your hardware based network infrastructure. Read more about the capabilities and how to get a basic configuration working in How to Set Up a Load-Balanced Application Across Two Oracle Solaris Zones

  Read the article

• Ubuntu 12.04 // Likewise Open // Unable to ever authenticate AD users

  - by Rob

  So Ubuntu 12.04, Likewise latest from the beyondtrust website. Joins domain fine. Gets proper information from lw-get-status. Can use lw-find-user-by-name to retrieve/locate users. Can use lw-enum-users to get all users. Attempting to login with an AD user via SSH generates the following errors in the auth.log file: Nov 28 19:15:45 hostname sshd[2745]: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:15:45 hostname sshd[2745]: PAM adding faulty module: pam_winbind.so Nov 28 19:15:51 hostname sshd[2745]: error: PAM: Authentication service cannot retrieve authentication info for DOMAIN\\user.name from remote.hostname Nov 28 19:16:06 hostname sshd[2745]: Connection closed by 10.1.1.84 [preauth] Attempting to login via the LightDM itself generates similar errors in the auth.log file. Nov 28 19:19:29 hostname lightdm: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:19:29 hostname lightdm: PAM adding faulty module: pam_winbind.so Nov 28 19:19:47 hostname lightdm: pam_succeed_if(lightdm:auth): requirement "user ingroup nopasswdlogin" not met by user "DOMAIN\user.name" Nov 28 19:19:52 hostname lightdm: [lsass-pam] [module:pam_lsass]pam_sm_authenticate error [login:DOMAIN\user.name][error code:40022] Nov 28 19:19:54 hostname lightdm: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:19:54 hostname lightdm: PAM adding faulty module: pam_winbind.so Attempting to login via a console on the system itself generates slightly different errors: Nov 28 19:31:09 hostname login[997]: PAM unable to dlopen(pam_winbind.so): /lib/security/pam_winbind.so: cannot open shared object file: No such file or directory Nov 28 19:31:09 hostname login[997]: PAM adding faulty module: pam_winbind.so Nov 28 19:31:11 hostname login[997]: [lsass-pam] [module:pam_lsass]pam_sm_authenticate error [login:DOMAIN\user.name][error code:40022] Nov 28 19:31:14 hostname login[997]: FAILED LOGIN (1) on '/dev/tty2' FOR 'DOMAIN\user.name', Authentication service cannot retrieve authentication info Nov 28 19:31:31 hostname login[997]: FAILED LOGIN (2) on '/dev/tty2' FOR 'DOMAIN\user.name', Authentication service cannot retrieve authentication info I am baffled. The errors obviously are correct, the file /lib/security/pam_winbind.so does not exist. If its a dependancy/required, surely it should be part of the package? I've installed/reinstalled, I've used the downloaded package from the beyondtrust website, i've used the repository, nothing seems to work, every method of installing this application generates the same errors for me. UPDATE : Hrmm, I thought likewise didn't use native winbind but its own modules. Installing winbind from apt-get uninstalls pbis-open (likewise) and generates failures when installing if pbis-open is installed first. Uninstalled winbind, reinstalled pbis-open, same issue as above. The file pam_winbind.so does not exist in that location. Setting up pbis-open-legacy (7.0.1.918) ... Installing Packages was successful This computer is joined to DOMAIN.LOCAL New libraries and configurations have been installed for PAM and NSS. Clearly it thinks it has installed it, but it hasn't. It may be a legacy issue with the previous attempt to configure domain integration manually with winbind. Does anyone have a working likewise-open installation and does the /etc/nsswitch.conf include references to winbind? Or do the /etc/pam.d/common-account or /etc/pam.d/common-password reference pam_winbind.so? I'm unsure if those entries are just legacy or setup by likewise. UPDATE 2 : Complete reinstall of OS fixed it and it worked seamlessly, like it was meant to and those 2 PAM files did NOT include entries for pam_winbind.so, so that was the underlying problem. Thanks for the assist.

  Read the article

• Transfer domains without disrupting local email server

  - by krosiris

  Perhaps I am thinking about this wrong, but maybe some of you guys can help me on this one. I have a client who currently has a domain from network solutions and is hosted via GoDaddy. Additionally, he his has email service with GoDaddy as well, but it seems to be forwarded to his local server at work. How can I transfer hosting accounts without disrupting email service (or at least temporarily)? Some MX info via Godaddy: A @ Points to GoDaddy Host main Points to client's home server sw Points to client's home server MX @ Points to main.example.com @ Points to smtp.secureserver @ Points to mailstore1.secureserver

  Read the article

• Tips for debugging Samba performance?

  - by j-g-faustus

  Samba gives me 24 MB/s read and 44 MB/s write, while ftp gives 97 and 112 MB/s under the same circumstances. The documentation says that Generally, you should find that Samba performs similarly to ftp at raw transfer speed. In my case it clearly doesn't. Where can I find tips on how to debug Samba performance? Or alternatively tips for replacing Samba with something else? (I can't use ftp, unfortunately, as I need something that can be used with rsync/rsnapshot.) More details: Both computers are running Ubuntu 10.10 (using Samba because I have a Mac as well) The Samba share is on a local home network, mounted as $ mount ... //server.local/share/ on /mnt/share type cifs (rw,mand) Samba performance was tested by copying (cp) a single file of ~4GB to and from the share, using time for timing and calculating transfer speed by hand. ftp performance are the numbers from the ftp client for get/put of the same file. iperf gives network speed ~900 Mbits/s bonnie++ gives disk speeds 200 MB/s on both sides for block reads as well as block writes Tried changing the parameters suggested in the performance tuning HOWTO (read/write raw, read size, socket options), most of them made little to no difference. (The one that made a difference caused write speed to drop 50%.)

  Read the article

• How to set-up DSL dialer for Ubuntu 12.04 LTS

  - by Mohammad Yaseen

  I have just installed Ubuntu 12.04 LTS and I'm unable to get my DSL dialer working properly. To set this up in Windows 7 I had to do following: Control Panel --- Network and Intertnet Network and sharing center --- Setup a new network or connection Connect to the internet --- Broadband PPPoE Enter username and Password.. CLick 'Connect' and Done. I am doing following steps in Ubuntu with no luck: Click on 'Two Arrows' (i don't know what they are called) on upper right corner. Configure VPN --- DSL tab --- Add Then I entered username, password, MAC address and Clone MAC address (copied from Auto Ethernet). Save The same set up used to work with Ubuntu 10.10 but it is not working here. Now whenever I click on DSL Connection 1 to connect dialer 'Auto Ethernet' gets disconneted and I end up with no Internet connection. I am new to Ubuntu, Please suggest some easy steps. I have installed ubuntu alongside windows. And dialer works fine in Windows environment, i am writing this in Windows .

  Read the article

• Bridged VM guest does not get IPv6 prefix

  - by Arne

  I have a similar problem and setup as described in IPv6 does not work over bridge. My host get a IPv6 prefix but the guest VM only gets a local fe80-prefix. Using tcpdump I can see that solicit messages are going out from the guest but the host (ubuntu-server) doesn't seem to respond: arne@ubuntu-server:/var/log$ sudo tcpdump -i br0 host fe80::5054:00ff:fe4d:9ae0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on br0, link-type EN10MB (Ethernet), capture size 65535 bytes 14:31:15.314419 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:15.322337 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.502374 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 1 group record(s), length 28 14:31:15.743894 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit 14:31:15.802389 IP6 fe80::5054:ff:fe4d:9ae0 > ff02::16: HBH ICMP6, multicast listener report v2, 4 group record(s), length 88 14:31:17.906580 IP6 fe80::5054:ff:fe4d:9ae0.dhcpv6-client > ff02::1:2.dhcpv6-server: dhcp6 solicit I had a firewall issue which I fixed by adding the following (copied from similar IPv4 before.rules settings) to /etc/ufw/before6.rules at the end before the commit statement: # allow bridging (for KVM) -I FORWARD -m physdev --physdev-is-bridged -j ACCEPT I am running the host on a Ubuntu 14.04 server so I guess I could have used dnsmasq but I didn't find any howto for it so I used radvd (which had to be installed) with the following configuration in /etc/radvd.conf: interface br0 { AdvSendAdvert on; AdvLinkMTU 1480; prefix 2a01:79d:xxx::/64 { AdvOnLink on; AdvAutonomous on; }; }; This didn't help though so I guess I must have configured it wrong? Any help appreciated. Br, Arne PS: I wish the Ubuntu documentation included how to configure virtualization to work with IPv6

  Read the article

• High number of ethernet errors. Tool for testing the ethernet card?

  - by Fabio Dalla Libera

  I have an Asus Sabertooth X79. I often get corrupted files. I checked the RAM, but memtest finds no errors. To avoid the possibility of disk errors, I tried copying the files to tmpfs. If I copy from the network, I get md5sum mismatches about once every 10 times using a 6Gb file. Copying from RAM to RAM, I didn't get mismatches. I get a very high number of errors in ifconfig (compared to others PCs I just took as reference, which have 0 with much more traffic). Here is an example RX packets:13972848 errors:200 dropped:0 overruns:0 frame:101 The motherboard is new, but do you think there're some problems with it? What could I use to test the (integrated) network adapter? What else do you think I should double check? --edit-- I tried another NIC, it gives a lot of Corrupted MAC on Input. Disconnecting: Packet corrupt lost connection. I noticed that another PC downloads at 11.1MB/s without problems. This pc at 66.0 MB/s. Is there any way to try to limit the speed?

  Read the article

• Movement prediction for non-shooters

  - by ShadowChaser

  I'm working on an isometric 2D game with moderate-scale multiplayer, approximately 20-30 players connected at once to a persistent server. I've had some difficulty getting a good movement prediction implementation in place. Physics/Movement The game doesn't have a true physics implementation, but uses the basic principles to implement movement. Rather than continually polling input, state changes (ie/ mouse down/up/move events) are used to change the state of the character entity the player is controlling. The player's direction (ie/ north-east) is combined with a constant speed and turned into a true 3D vector - the entity's velocity. In the main game loop, "Update" is called before "Draw". The update logic triggers a "physics update task" that tracks all entities with a non-zero velocity uses very basic integration to change the entities position. For example: entity.Position += entity.Velocity.Scale(ElapsedTime.Seconds) (where "Seconds" is a floating point value, but the same approach would work for millisecond integer values). The key point is that no interpolation is used for movement - the rudimentary physics engine has no concept of a "previous state" or "current state", only a position and velocity. State Change and Update Packets When the velocity of the character entity the player is controlling changes, a "move avatar" packet is sent to the server containing the entity's action type (stand, walk, run), direction (north-east), and current position. This is different from how 3D first person games work. In a 3D game the velocity (direction) can change frame to frame as the player moves around. Sending every state change would effectively transmit a packet per frame, which would be too expensive. Instead, 3D games seem to ignore state changes and send "state update" packets on a fixed interval - say, every 80-150ms. Since speed and direction updates occur much less frequently in my game, I can get away with sending every state change. Although all of the physics simulations occur at the same speed and are deterministic, latency is still an issue. For that reason, I send out routine position update packets (similar to a 3D game) but much less frequently - right now every 250ms, but I suspect with good prediction I can easily boost it towards 500ms. The biggest problem is that I've now deviated from the norm - all other documentation, guides, and samples online send routine updates and interpolate between the two states. It seems incompatible with my architecture, and I need to come up with a better movement prediction algorithm that is closer to a (very basic) "networked physics" architecture. The server then receives the packet and determines the players speed from it's movement type based on a script (Is the player able to run? Get the player's running speed). Once it has the speed, it combines it with the direction to get a vector - the entity's velocity. Some cheat detection and basic validation occurs, and the entity on the server side is updated with the current velocity, direction, and position. Basic throttling is also performed to prevent players from flooding the server with movement requests. After updating its own entity, the server broadcasts an "avatar position update" packet to all other players within range. The position update packet is used to update the client side physics simulations (world state) of the remote clients and perform prediction and lag compensation. Prediction and Lag Compensation As mentioned above, clients are authoritative for their own position. Except in cases of cheating or anomalies, the client's avatar will never be repositioned by the server. No extrapolation ("move now and correct later") is required for the client's avatar - what the player sees is correct. However, some sort of extrapolation or interpolation is required for all remote entities that are moving. Some sort of prediction and/or lag-compensation is clearly required within the client's local simulation / physics engine. Problems I've been struggling with various algorithms, and have a number of questions and problems: Should I be extrapolating, interpolating, or both? My "gut feeling" is that I should be using pure extrapolation based on velocity. State change is received by the client, client computes a "predicted" velocity that compensates for lag, and the regular physics system does the rest. However, it feels at odds to all other sample code and articles - they all seem to store a number of states and perform interpolation without a physics engine. When a packet arrives, I've tried interpolating the packet's position with the packet's velocity over a fixed time period (say, 200ms). I then take the difference between the interpolated position and the current "error" position to compute a new vector and place that on the entity instead of the velocity that was sent. However, the assumption is that another packet will arrive in that time interval, and it's incredibly difficult to "guess" when the next packet will arrive - especially since they don't all arrive on fixed intervals (ie/ state changes as well). Is the concept fundamentally flawed, or is it correct but needs some fixes / adjustments? What happens when a remote player stops? I can immediately stop the entity, but it will be positioned in the "wrong" spot until it moves again. If I estimate a vector or try to interpolate, I have an issue because I don't store the previous state - the physics engine has no way to say "you need to stop after you reach position X". It simply understands a velocity, nothing more complex. I'm reluctant to add the "packet movement state" information to the entities or physics engine, since it violates basic design principles and bleeds network code across the rest of the game engine. What should happen when entities collide? There are three scenarios - the controlling player collides locally, two entities collide on the server during a position update, or a remote entity update collides on the local client. In all cases I'm uncertain how to handle the collision - aside from cheating, both states are "correct" but at different time periods. In the case of a remote entity it doesn't make sense to draw it walking through a wall, so I perform collision detection on the local client and cause it to "stop". Based on point #2 above, I might compute a "corrected vector" that continually tries to move the entity "through the wall" which will never succeed - the remote avatar is stuck there until the error gets too high and it "snaps" into position. How do games work around this?

  Read the article

• What is the structure of network managers system-connections files?

  - by Oyks Livede

  could anyone list the complete structure of the configuration files, which network manager stores for known networks in /etc/NetworkManager/system-connections for known networks? Sample (filename askUbuntu): [connection] id=askUbuntu uuid=81255b2e-bdf1-4bdb-b6f5-b94ef16550cd type=802-11-wireless [802-11-wireless] ssid=askUbuntu mode=infrastructure mac-address=00:08:CA:E6:76:D8 [ipv6] method=auto [ipv4] method=auto I would like to create some of them by my own using a script. However, before doing so I would like to know every possible option. Furthermore, this structure seems somehow to resemble the information you can get using the dbus for active connections. dbus-send --system --print-reply \ --dest=org.freedesktop.NetworkManager \ "$active_setting_path" \ # /org/freedesktop/NetworkManager/Settings/2 org.freedesktop.NetworkManager.Settings.Connection.GetSettings Will tell you: array [ dict entry( string "802-11-wireless" array [ dict entry( string "ssid" variant array of bytes "askUbuntu" ) dict entry( string "mode" variant string "infrastructure" ) dict entry( string "mac-address" variant array of bytes [ 00 08 ca e6 76 d8 ] ) dict entry( string "seen-bssids" variant array [ string "02:1A:11:F8:C5:64" string "02:1A:11:FD:1F:EA" ] ) ] ) dict entry( string "connection" array [ dict entry( string "id" variant string "askUbuntu" ) dict entry( string "uuid" variant string "81255b2e-bdf1-4bdb-b6f5-b94ef16550cd" ) dict entry( string "timestamp" variant uint64 1383146668 ) dict entry( string "type" variant string "802-11-wireless" ) ] ) dict entry( string "ipv4" array [ dict entry( string "addresses" variant array [ ] ) dict entry( string "dns" variant array [ ] ) dict entry( string "method" variant string "auto" ) dict entry( string "routes" variant array [ ] ) ] ) dict entry( string "ipv6" array [ dict entry( string "addresses" variant array [ ] ) dict entry( string "dns" variant array [ ] ) dict entry( string "method" variant string "auto" ) dict entry( string "routes" variant array [ ] ) ] ) ] I can create new setting files using the dbus (AddSettings() in /org/freedesktop/NetworkManager/Settings) passing this type of input, so explaining me this structure and telling me all possible options will also help. Afaik, this is a Dictionary{String, Dictionary{String, Variant}}. Will there be any difference creating config files directly or using the dbus?

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >