Search Results

Search found 24931 results on 998 pages for 'information visualization'.

Page 939/998 | < Previous Page | 935 936 937 938 939 940 941 942 943 944 945 946  | Next Page >

• Cisco 678 Will Not Work using PPPoE - Possibly Because I Configured it Incorrectly..?

  - by Brian Stinar

  I am attempting to configure a Cisco 678 because I am totally sick on my Actiontec. However, I am running into some problems. It seems as though the Cisco is able to train the line, but I am unable to ping out. I am all right at programming, but still learning a lot when it comes to being a system administrator. I apologize in advance if I did something ridiculous, or am attempting to configure this device to do something it was not designed to do. It is almost like I am not correctly configuring the device to grab it's IP using PPPoA (like my Actiontec.) The output from "show running" (below) makes me think this too. Below are the commands I ran in order to configure this: # en # set nvram erase # write # reboot # en # set nat enable # set dhcp server enable # set PPP wan0-0 ipcp 0.0.0.0 # set ppp wan0-0 dns 0.0.0.0 # set PPP wan0-0 login xxxxx // My actual login # set PPP wan0-0 password yyyyy // My actual password # set PPP restart enabled # set int wan0-0 close # set int wan0-0 vpi 0 # set int wan0-0 vci 32 # set int wan0-0 open # write # reboot Here is the output from a few commands I thought could provide some useful information: cbos#ping 74.125.224.113 Sending 1 8 byte ping(s) to 74.125.224.113 every 2 second(s) Request timed out cbos#show version Cisco Broadband Operating System CBOS (tm) 678 Software (C678-I-M), Version v2.4.9 - Release Software Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Nov 17 2004 15:26:29 DMT FULL firmware version G96 NVRAM image at 0x1030f000 cbos#show errors - Current Error Messages - ## Ticks Module Level Message 0 000:00:00:00 PPP Info IPCP Open Event on wan0-0 1 000:00:00:14 ATM Info Wan0 Up 2 000:00:00:14 PPP Info PPP Up Event on wan0-0 3 000:00:01:54 PPP Info PPP Down Event on wan0-0 Total Number of Error Messages: 4 cbos#show interface wan0 wan0 ADSL Physical Port Line Trained Actual Configuration: Overhead Framing: 3 Trellis Coding: Enabled Standard Compliance: T1.413 Downstream Data Rate: 1184 Kbps Upstream Data Rate: 928 Kbps Interleave S Downstream: 4 Interleave D Downstream: 16 Interleave R Downstream: 16 Interleave S Upstream: 4 Interleave D Upstream: 8 Interleave R Upstream: 16 Modem Microcode: G96 DSP version: 0 Operating State: Showtime/Data Mode Configured: Echo Cancellation: Disabled Overhead Framing: 3 Coding Gain: Auto TX Power Attenuation: 0dB Trellis Coding: Enabled Bit Swapping: Disabled Standard Compliance: T1.413 Remote Standard Compliance: T1.413 Tx Start Bin: 0x6 Tx End Bin: 0x1f Data Interface: Utopia L1 Status: Local SNR Margin: 19.0dB Local Coding Gain: 7.5dB Local Transmit Power: 12.5dB Local Attenuation: 46.0dB Remote Attenuation: 31.0dB Local Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 2 No Cell Delineation Interleaved: 0 Out of Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 Remote Counters: Interleaved RS Corrected Bytes: 0 Interleaved Symbols with CRC Errors: 1 No Cell Delineation Interleaved: 0 Header Error Check Counter Interleaved: 0 Count of Severely Errored Frames: 0 Count of Loss of Signal Frames: 0 cbos#show int wan0-0 WAN0-0 ATM Logical Port PVC (VPI 0, VCI 32) is configured. ScalaRate set to Auto AAL 5 UBR Traffic IP Port Enabled cbos#show running Warning: traffic may pause while NVRAM is being accessed [[ CBOS = Section Start ]] NSOS MD5 Enable Password = XXXX NSOS MD5 Root Password = XXXX NSOS MD5 Commander Password = XXXX [[ PPP Device Driver = Section Start ]] PPP Port User Name = 00, "XXXX" PPP Port User Password = 00, XXXX PPP Port Option = 00, IPCP,IP Address,3,Auto,Negotiation Not Required,Negotiable ,IP,0.0.0.0 PPP Port Option = 00, IPCP,Primary DNS Server,129,Auto,Negotiation Not Required, Negotiable,IP,0.0.0.0 PPP Port Option = 00, IPCP,Secondary DNS Server,131,Auto,Negotiation Not Require d,Negotiable,IP,0.0.0.0 [[ ATM WAN Device Driver = Section Start ]] ATM WAN Virtual Connection Parms = 00, 0, 32, 0 [[ DHCP = Section Start ]] DHCP Server = enabled [[ IP Routing = Section Start ]] IP NAT = enabled [[ WEB = Section Start ]] WEB = enabled cbos# wtf...? Thank you all very much for taking the time to read this, and the help.

  Read the article

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• Debian virtual memory reaching limit

  - by Gregor

  As a relative newbie to systems, I inherited a Debian server and I've noticed that virtual memory is very high (around 95%!). The server has been running slow for around 6 months, and I was wondering if any of you had any tips on things I could try, particularly on freeing up memory. The server hosts various websites and also a Postit email server. Here are the details: Operating system Debian Linux 5.0 Webmin version 1.580 Time on system Thu Apr 12 11:12:21 2012 Kernel and CPU Linux 2.6.18-6-amd64 on x86_64 Processor information Intel(R) Core(TM)2 Duo CPU E7400 @ 2.80GHz, 2 cores System uptime 229 days, 12 hours, 50 minutes Running processes 138 CPU load averages 0.10 (1 min) 0.28 (5 mins) 0.36 (15 mins) CPU usage 14% user, 1% kernel, 0% IO, 85% idle Real memory 2.94 GB total, 1.69 GB used Virtual memory 3.93 GB total, 3.84 GB used Local disk space 142.84 GB total, 116.13 GB used Free m output: free -m total used free shared buffers cached Mem: 3010 2517 492 0 107 996 -/+ buffers/cache: 1413 1596 Swap: 4024 3930 93 Top output: top - 11:59:57 up 229 days, 13:38, 1 user, load average: 0.26, 0.24, 0.26 Tasks: 136 total, 2 running, 134 sleeping, 0 stopped, 0 zombie Cpu(s): 3.8%us, 0.5%sy, 0.0%ni, 95.0%id, 0.7%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3082544k total, 2773160k used, 309384k free, 111496k buffers Swap: 4120632k total, 4024712k used, 95920k free, 1036136k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 28796 www-data 16 0 304m 68m 6188 S 8 2.3 0:03.13 apache2 1 root 15 0 10304 592 564 S 0 0.0 0:00.76 init 2 root RT 0 0 0 0 S 0 0.0 0:04.06 migration/0 3 root 34 19 0 0 0 S 0 0.0 0:05.67 ksoftirqd/0 4 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 5 root RT 0 0 0 0 S 0 0.0 0:00.06 migration/1 6 root 34 19 0 0 0 S 0 0.0 0:01.26 ksoftirqd/1 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/1 8 root 10 -5 0 0 0 S 0 0.0 0:00.12 events/0 9 root 10 -5 0 0 0 S 0 0.0 0:00.00 events/1 10 root 10 -5 0 0 0 S 0 0.0 0:00.00 khelper 11 root 10 -5 0 0 0 S 0 0.0 0:00.02 kthread 16 root 10 -5 0 0 0 S 0 0.0 0:15.51 kblockd/0 17 root 10 -5 0 0 0 S 0 0.0 0:01.32 kblockd/1 18 root 15 -5 0 0 0 S 0 0.0 0:00.00 kacpid 127 root 10 -5 0 0 0 S 0 0.0 0:00.00 khubd 129 root 10 -5 0 0 0 S 0 0.0 0:00.00 kseriod 180 root 10 -5 0 0 0 S 0 0.0 70:09.05 kswapd0 181 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/0 182 root 17 -5 0 0 0 S 0 0.0 0:00.00 aio/1 780 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/0 782 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata/1 783 root 16 -5 0 0 0 S 0 0.0 0:00.00 ata_aux 802 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_0 803 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_1 804 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_2 805 root 10 -5 0 0 0 S 0 0.0 0:00.00 scsi_eh_3 1013 root 10 -5 0 0 0 S 0 0.0 49:27.78 kjournald 1181 root 15 -4 16912 452 448 S 0 0.0 0:00.05 udevd 1544 root 14 -5 0 0 0 S 0 0.0 0:00.00 kpsmoused 1706 root 13 -5 0 0 0 S 0 0.0 0:00.00 kmirrord 1995 root 18 0 193m 3324 1688 S 0 0.1 8:52.77 rsyslogd 2031 root 15 0 48856 732 608 S 0 0.0 0:01.86 sshd 2071 root 25 0 17316 1072 1068 S 0 0.0 0:00.00 mysqld_safe 2108 mysql 15 0 320m 72m 4368 S 0 2.4 1923:25 mysqld 2109 root 18 0 3776 500 496 S 0 0.0 0:00.00 logger 2180 postgres 15 0 99504 3016 2880 S 0 0.1 1:24.15 postgres 2184 postgres 15 0 99504 3596 3420 S 0 0.1 0:02.08 postgres 2185 postgres 15 0 99504 696 628 S 0 0.0 0:00.65 postgres 2186 postgres 15 0 99640 892 648 S 0 0.0 0:01.18 postgres

  Read the article

• Looking for advice on Hyper-v storage replication

  - by Notre1

  I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

  Read the article

• Trying to connect phpMyAdmin to remote mySQL server ( 2002: can't connect )

  - by Malcolm Jones

  Trying to get phpMyAdmin to talk to a remote mySQL server. The config is below and there is already a user set up in mySQL DB to be able to log in from the specified host that PMA sits on. Hosting is provided by Rackspace (Rightscale) and both cloud servers behind the same firewall. [config.inc.php] <?php $cfg['blowfish_secret'] = ''; $i = 0; $i++; $cfg['Servers'][$i]['host'] = 'XX.XX.XX.XX'; // MySQL hostname or IP address $cfg['Servers'][$i]['port'] = ''; // MySQL port - leave blank for default port $cfg['Servers'][$i]['socket'] = ''; // Path to the socket - leave blank for default socket $cfg['Servers'][$i]['connect_type'] = 'tcp'; // How to connect to MySQL server ('tcp' or 'socket') $cfg['Servers'][$i]['extension'] = 'mysql'; // The php MySQL extension to use ('mysql' or 'mysqli') $cfg['Servers'][$i]['compress'] = FALSE; // Use compressed protocol for the MySQL connection // (requires PHP >= 4.3.0) $cfg['Servers'][$i]['controluser'] = ''; // MySQL control user settings // (this user must have read-only $cfg['Servers'][$i]['controlpass'] = ''; // access to the "mysql/user" // and "mysql/db" tables). // The controluser is also // used for all relational // features (pmadb) $cfg['Servers'][$i]['auth_type'] = 'config'; // Authentication method (config, http or cookie based)? $cfg['Servers'][$i]['user'] = 'USERNAME'; // MySQL user $cfg['Servers'][$i]['password'] = 'PASSWORD'; // MySQL password (only needed // with 'config' auth_type) $cfg['Servers'][$i]['only_db'] = ''; // If set to a db-name, only // this db is displayed in left frame // It may also be an array of db-names, where sorting order is relevant. $cfg['Servers'][$i]['hide_db'] = ''; // Database name to be hidden from listings $cfg['Servers'][$i]['verbose'] = ''; // Verbose name for this host - leave blank to show the hostname $cfg['Servers'][$i]['pmadb'] = ''; // Database used for Relation, Bookmark and PDF Features // (see scripts/create_tables.sql) // - leave blank for no support // DEFAULT: 'phpmyadmin' $cfg['Servers'][$i]['bookmarktable'] = ''; // Bookmark table // - leave blank for no bookmark support // DEFAULT: 'pma_bookmark' $cfg['Servers'][$i]['relation'] = ''; // table to describe the relation between links (see doc) // - leave blank for no relation-links support // DEFAULT: 'pma_relation' $cfg['Servers'][$i]['table_info'] = ''; // table to describe the display fields // - leave blank for no display fields support // DEFAULT: 'pma_table_info' $cfg['Servers'][$i]['table_coords'] = ''; // table to describe the tables position for the PDF schema // - leave blank for no PDF schema support // DEFAULT: 'pma_table_coords' $cfg['Servers'][$i]['pdf_pages'] = ''; // table to describe pages of relationpdf // - leave blank if you don't want to use this // DEFAULT: 'pma_pdf_pages' $cfg['Servers'][$i]['column_info'] = ''; // table to store column information // - leave blank for no column comments/mime types // DEFAULT: 'pma_column_info' $cfg['Servers'][$i]['history'] = ''; // table to store SQL history // - leave blank for no SQL query history // DEFAULT: 'pma_history' $cfg['Servers'][$i]['verbose_check'] = TRUE; // set to FALSE if you know that your pma_* tables // are up to date. This prevents compatibility // checks and thereby increases performance. $cfg['Servers'][$i]['AllowRoot'] = TRUE; // whether to allow root login $cfg['Servers'][$i]['AllowDeny']['order'] // Host authentication order, leave blank to not use = ''; $cfg['Servers'][$i]['AllowDeny']['rules'] // Host authentication rules, leave blank for defaults = array(); Please let me know if you need anymore info. -- Malcolm

  Read the article

• Where's my memory?! Nginx + PHP-FPM front end webserver slows to a crawl...

  - by incredimike

  I'm not sure if I have a problem with a memory leak (as my hosting company suggests), or if we both need to read http://linuxatemyram.com. Maybe you clever people can help us out? This is a front-end webserver VM running essentially only nginx & php-fpm on RHEL 5.5. This server is powering Magento, a PHP eCommerce thinggy. The server is running in a shared environment, but we're changing that soon. Anyway.. after a reboot the server runs just fine, but within a day it will grind itself into nothingness. Pages will take literally 2 minutes to load, CPU spikes like crazy, etc.. The console is even sluggish when I SSH in. It's like my whole server is being brought to its knees. I've also been monitoring the DB server via top and tcpdumping incoming traffic. The DB stays idle for a good portion of that "slow" load time. When i start seeing queries coming from the front-end server, the page loads soon afterward. Here are some stats after me logging in during a slow-down, after restarting php-fpm: [mike@front01 ~]$ free -m total used free shared buffers cached Mem: 5963 5217 745 0 192 314 -/+ buffers/cache: 4711 1252 Swap: 4047 4 4042 [mike@front01 ~]$ top top - 11:38:55 up 2 days, 1:01, 3 users, load average: 0.06, 0.17, 0.21 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.3%sy, 0.0%ni, 99.3%id, 0.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.3%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 6106800k total, 5361288k used, 745512k free, 199960k buffers Swap: 4144728k total, 4976k used, 4139752k free, 328480k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31806 apache 15 0 601m 120m 37m S 0.0 2.0 0:22.23 php-fpm 31805 apache 15 0 549m 66m 31m S 0.0 1.1 0:14.54 php-fpm 31809 apache 16 0 547m 65m 32m S 0.0 1.1 0:12.84 php-fpm 32285 apache 15 0 546m 63m 33m S 0.0 1.1 0:09.22 php-fpm 32373 apache 15 0 546m 62m 32m S 0.0 1.1 0:09.66 php-fpm 31808 apache 16 0 543m 60m 35m S 0.0 1.0 0:18.93 php-fpm 31807 apache 16 0 533m 49m 30m S 0.0 0.8 0:08.93 php-fpm 32092 apache 15 0 535m 48m 27m S 0.0 0.8 0:06.67 php-fpm 4392 root 18 0 194m 10m 7184 S 0.0 0.2 0:06.96 cvd 4064 root 15 0 154m 8304 4220 S 0.0 0.1 3:55.57 snmpd 4394 root 15 0 119m 5660 2944 S 0.0 0.1 0:02.84 EvMgrC 31804 root 15 0 519m 5180 932 S 0.0 0.1 0:00.46 php-fpm 4138 ntp 15 0 23396 5032 3904 S 0.0 0.1 0:02.38 ntpd 643 nginx 15 0 95276 4408 1524 S 0.0 0.1 0:01.15 nginx 5131 root 16 0 90128 3340 2600 S 0.0 0.1 0:01.41 sshd 28467 root 15 0 90128 3340 2600 S 0.0 0.1 0:00.35 sshd 32602 root 16 0 90128 3332 2600 S 0.0 0.1 0:00.36 sshd 1614 root 16 0 90128 3308 2588 S 0.0 0.1 0:00.02 sshd 2817 root 5 -10 7216 3140 1724 S 0.0 0.1 0:03.80 iscsid 4161 root 15 0 66948 2340 800 S 0.0 0.0 0:10.35 sendmail 1617 nicole 17 0 53876 2000 1516 S 0.0 0.0 0:00.02 sftp-server ... Is there anything else I should be looking at, or any more information that might be useful? I'm just a developer, but the slowdowns on this system worry me and make it hard to do my work.. Help me out, ServerFault!

  Read the article

• Reinstall Postfix

  - by Kevin

  I tried to reinstall Postfix, but I get this bunch of errors: root@***:/etc/init.d# sudo apt-get install -f postfix Reading package lists... Done Building dependency tree Reading state information... Done Suggested packages: procmail postfix-mysql postfix-pgsql postfix-ldap postfix-pcre resolvconf postfix-cdb mail-reader The following NEW packages will be installed: postfix 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/1,389kB of archives. After this operation, 3,531kB of additional disk space will be used. Preconfiguring packages ... Selecting previously deselected package postfix. (Reading database ... 56122 files and directories currently installed.) Unpacking postfix (from .../postfix_2.7.1-1ubuntu0.1_amd64.deb) ... Processing triggers for ureadahead ... Processing triggers for ufw ... Processing triggers for man-db ... Setting up postfix (2.7.1-1ubuntu0.1) ... Configuration file `/etc/init.d/postfix' ==> File on system created by you or by a script. ==> File also in package provided by package maintainer. What would you like to do about it ? Your options are: Y or I : install the package maintainer's version N or O : keep your currently-installed version D : show the differences between the versions Z : start a shell to examine the situation The default action is to keep your current version. *** postfix (Y/I/N/O/D/Z) [default=N] ? Y Installing new version of config file /etc/init.d/postfix ... Adding group `postfix' (GID 109) ... Done. Adding system user `postfix' (UID 106) ... Adding new user `postfix' (UID 106) with group `postfix' ... Not creating home directory `/var/spool/postfix'. Creating /etc/postfix/dynamicmaps.cf Adding tcp map entry to /etc/postfix/dynamicmaps.cf Adding group `postdrop' (GID 115) ... Done. setting myhostname: ***.net setting alias maps setting alias database setting myorigin setting destinations: ***.net, localhost.***.net, , localhost setting relayhost: setting mynetworks: 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 setting mailbox_size_limit: 0 setting recipient_delimiter: + setting inet_interfaces: all Postfix is now set up with a default configuration. If you need to make changes, edit /etc/postfix/main.cf (and others) as needed. To view Postfix configuration values, see postconf(1). After modifying main.cf, be sure to run '/etc/init.d/postfix reload'. Running newaliases postalias: fatal: /etc/mailname: cannot open file: Permission denied dpkg: error processing postfix (--configure): subprocess installed post-installation script returned error exit status 1 Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: postfix E: Sub-process /usr/bin/dpkg returned an error code (1) I tried aptitude purge, remove, autoclean and all of dpkg options (configure, remove, purge) but nothing did the trick. /etc/mailname exists (0644 root:root) with as content *.net (fetched from hostname). What am I doing wrong?

  Read the article

• .AVI Files randomly cease to open, other strange errors too

  - by Ben Franchuk

  I Recently (a couple weeks ago) downloaded the complete series of Seinfeld, all in varying file type. I Watched them in sequence according to season and to airing date, and all was well. All of the files played fine with my media player of choice ("BS Player"), and once I had finished, I went onto watch some other TV I had previously downloaded (The U.S. Series of "The Office"), and after then, some other film and then some music, over the following weeks (keep in mind all of these files are all on the same Hard Drive). Later then, More recently, I Went back to watching Seinfeld. The episodes played well as they did before- with the exclusion of a few in Season 7. I Have not tested all of the episodes in the season, but upon inspection, the majority of them are experiencing this problem; the problem being simply that they don't open! BS Player says that the files are either damaged or that the codecs to play the files are not on my computer-- however I am certain that the files DO have the codecs, and I am pretty sure that they are NOT DAMAGED either. I Have played the files with other players (such as VLC, Media Player Classic, and Windows Media Player), too, only to the same result; of them not opening. Seemingly the only way that I can differentiate between a damaged file and a non-damaged file are the way that the icon shows in Windows Explorer. For example, the below image is how explorer shows the information of a file that is non-damaged... ...and below is how a damaged file appears... The most disturbing and confusing part of this, though, is the last episode in the season- It opens, but not as a video- Instead, as a 1 Hour, 16 Minute, and 35 Second Audio file! The file plays a song for the first 4 or so minutes, and then is pretty much silent (except for some extremely quiet noise) until the last minute or so, when a random array of chopped up sounds and beeping noises play. I Do not recognise the song at the beginning of the file, but by the sounds of it, it is a song by the artist "Mr. Oizo," who's complete works I downloaded a couple weeks before now; and a bit before then I had finished downloading season 9 (not affected by these problems) of Seinfeld. I'd also like to note that the file I told of earlier (which played audio instead of video) reads as the same size as the other files in the season (around 175 MB) and also opens as a video clip. I Have NEVER experienced any of these problems in the past, and they seem to be only effecting the one season of my downloaded TV. The problems have not arisen with any of the other files on my Hard Drive, or any of the files downloaded around the time or after the time of which I downloaded season 7 of Seinfeld- or at least to my noticing. I Use the hard drive these files are located on almost every day, so could that be the cause of these problems? Is this a sign that my HDD is soon going to die? If it helps, the HDD is a Western Digital MyBook 1.5 TB 7500 RPM. It is connected to the computer via U.S.B. 2.0. EDIT! I noticed that this problem is now occurring with Season 9 of Seinfeld- and, presumably, other files on the drive I have yet to check. Please, If you have ANY IDEA AT ALL on what may be causing this or how to fix it, do tell me!

  Read the article

• dpkg: error processing /var/cache/apt/archives/python2.6-minimal_2.6.6-5ubuntu1_i386.deb (--unpack)

  - by udo

  I had an issue (Question 199582) which was resolved. Unfortunately I am stuck at this point now. Running root@X100e:/var/cache/apt/archives# apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following NEW packages will be installed: file libexpat1 libmagic1 libreadline6 libsqlite3-0 mime-support python python-minimal python2.6 python2.6-minimal readline-common 0 upgraded, 11 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/5,204kB of archives. After this operation, 19.7MB of additional disk space will be used. Do you want to continue [Y/n]? Y (Reading database ... 6108 files and directories currently installed.) Unpacking python2.6-minimal (from .../python2.6-minimal_2.6.6-5ubuntu1_i386.deb) ... new installation of python2.6-minimal; /usr/lib/python2.6/site-packages is a directory which is expected a symlink to /usr/local/lib/python2.6/dist-packages. please find the package shipping files in /usr/lib/python2.6/site-packages and file a bug report to ship these in /usr/lib/python2.6/dist-packages instead aborting installation of python2.6-minimal dpkg: error processing /var/cache/apt/archives/python2.6-minimal_2.6.6-5ubuntu1_i386.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/python2.6-minimal_2.6.6-5ubuntu1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) results in above error. Running root@X100e:/var/cache/apt/archives# dpkg -i python2.6-minimal_2.6.6-5ubuntu1_i386.deb (Reading database ... 6108 files and directories currently installed.) Unpacking python2.6-minimal (from python2.6-minimal_2.6.6-5ubuntu1_i386.deb) ... new installation of python2.6-minimal; /usr/lib/python2.6/site-packages is a directory which is expected a symlink to /usr/local/lib/python2.6/dist-packages. please find the package shipping files in /usr/lib/python2.6/site-packages and file a bug report to ship these in /usr/lib/python2.6/dist-packages instead aborting installation of python2.6-minimal dpkg: error processing python2.6-minimal_2.6.6-5ubuntu1_i386.deb (--install): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: python2.6-minimal_2.6.6-5ubuntu1_i386.deb results in above error. Running root@X100e:/var/cache/apt/archives# dpkg -i --force-depends python2.6-minimal_2.6.6-5ubuntu1_i386.deb (Reading database ... 6108 files and directories currently installed.) Unpacking python2.6-minimal (from python2.6-minimal_2.6.6-5ubuntu1_i386.deb) ... new installation of python2.6-minimal; /usr/lib/python2.6/site-packages is a directory which is expected a symlink to /usr/local/lib/python2.6/dist-packages. please find the package shipping files in /usr/lib/python2.6/site-packages and file a bug report to ship these in /usr/lib/python2.6/dist-packages instead aborting installation of python2.6-minimal dpkg: error processing python2.6-minimal_2.6.6-5ubuntu1_i386.deb (--install): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: python2.6-minimal_2.6.6-5ubuntu1_i386.deb is not able to fix this. Any clues how to fix this?

  Read the article

• File server share access intermittent/slow/machine unstable: win2k8r2

  - by Jack B.

  I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

  Read the article

• Why don't mails show up in the recipient's mailspool?

  - by Jason

  I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

  Read the article

• Do hard drive enclosures fail/is it the HDD or enclosure?

  - by x0a

  I'm having a whole host of problems with an external hard drive that was working just fine a couple of hours ago. I've had this problem before once, and that was about 3 months ago, here's what I documented: So a couple of hours ago I turned off all my computers and shut off the power to all my devices in my room, then went and turned the power off at the main switch so I could change an outlet. A couple hours later, after I've already slowly turned everything back on, I go to my xbox to try and watch a movie and it can't seem to list any of the movies I've got. So I go to my desktop to find that my external hard drive isn't there.. even though it's on and connected. It's also stationary and hidden behind something so there's not a whole lot of tampering/physical wear to that external. I plug it into my laptop to try and see what's going on. It starts making this endless loud screeching noise. None of that clicking that's usually associated with hd damage. It's not listed in my computers, and it shows up in Disk Management as "uninitialized" asking me to choose between two different partition types. After carefully disconnecting it and connecting it back, it asks me to format it, which I cancel. I start googling about my issue, starting to accept the situation, torn as hell and helpless and just about ready to toss the thing. Suddenly the screeching stops, after almost 45 minutes of it going, and Disk Management lists the drive as "Online" and "Healthy". Explorer pops up with all my files! I'm still being really careful with it and weary and treating it as though it's in fragile shape. I've downloaded some S.M.A.R.T. software to read the values and everything is listed as "OK" . No reallocated sectors, no read errors, no seek errors. I also ran a quick self-test, which completed without error. Everything seems fine. It looks to be a perfectly healthy external hard drive. So what the hell was that about? Was it doing some sort of maintenance or self-test? How am I supposed to tell the difference? I would've undoubtedly killed the drive for sure if had it gone on a bit longer. I've got the same problem now, with one exception: it doesn't magically reappear after the screeching stops. Occasionally I manage to get some S.M.A.R.T. diagnostics information, which basically reads everything as fine. The only problem is that my HD isn't initializing (so I can't access anything in it). I'm able to successfully run a quick smart test but not an extended one (I've only tried it once but got conflicting indications as to whether it was actually making any progress or not (was stuck on Random read test). So, final question (if all else fails): Could the hard drive enclosure be failing rather than the HDD? Is this a likely possibility at all? How would I know?

  Read the article

• What's the difference between find and findstr commands in Windows?

  - by Prashant Bhate

  In Windows, what are the differences between find and findstr commands? Both seems to search text in files: find c:\>find /? Searches for a text string in a file or files. FIND [/V] [/C] [/N] [/I] [/OFF[LINE]] "string" [[drive:][path]filename[ ...]] /V Displays all lines NOT containing the specified string. /C Displays only the count of lines containing the string. /N Displays line numbers with the displayed lines. /I Ignores the case of characters when searching for the string. /OFF[LINE] Do not skip files with offline attribute set. "string" Specifies the text string to find. [drive:][path]filename Specifies a file or files to search. If a path is not specified, FIND searches the text typed at the prompt or piped from another command. findstr c:\>findstr /? Searches for strings in files. FINDSTR [/B] [/E] [/L] [/R] [/S] [/I] [/X] [/V] [/N] [/M] [/O] [/P] [/F:file] [/C:string] [/G:file] [/D:dir list] [/A:color attributes] [/OFF[LINE]] strings [[drive:][path]filename[ ...]] /B Matches pattern if at the beginning of a line. /E Matches pattern if at the end of a line. /L Uses search strings literally. /R Uses search strings as regular expressions. /S Searches for matching files in the current directory and all subdirectories. /I Specifies that the search is not to be case-sensitive. /X Prints lines that match exactly. /V Prints only lines that do not contain a match. /N Prints the line number before each line that matches. /M Prints only the filename if a file contains a match. /O Prints character offset before each matching line. /P Skip files with non-printable characters. /OFF[LINE] Do not skip files with offline attribute set. /A:attr Specifies color attribute with two hex digits. See "color /?" /F:file Reads file list from the specified file(/ stands for console). /C:string Uses specified string as a literal search string. /G:file Gets search strings from the specified file(/ stands for console). /D:dir Search a semicolon delimited list of directories strings Text to be searched for. [drive:][path]filename Specifies a file or files to search. Use spaces to separate multiple search strings unless the argument is prefixed with /C. For example, 'FINDSTR "hello there" x.y' searches for "hello" or "there" in file x.y. 'FINDSTR /C:"hello there" x.y' searches for "hello there" in file x.y. Regular expression quick reference: . Wildcard: any character * Repeat: zero or more occurances of previous character or class ^ Line position: beginning of line $ Line position: end of line [class] Character class: any one character in set [^class] Inverse class: any one character not in set [x-y] Range: any characters within the specified range \x Escape: literal use of metacharacter x \<xyz Word position: beginning of word xyz\> Word position: end of word For full information on FINDSTR regular expressions refer to the online Command Reference.

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• Specifying a Postfix Instance to send outbound email

  - by Catherine Jefferson

  I have a CentOS 6.5 server running Postfix 2.6x (the default distribution) with five public IPv4 IPs bound to it. Each IP has DNS and rDNS set separately. Each uses a different hostname at a different domain. I have five Postfix instances, one bound to each IP, like this example: 192.168.34.104 red.example.com /etc/postfix 192.168.36.48 green.example.net /etc/postfix-green 192.168.36.49 pink.example.org /etc/postfix-pink 192.168.36.50 orange.example.info /etc/postfix-orange 192.168.36.51 blue.example.us /etc/postfix-blue I've tested each IP by telneting to port 25. Postfix answers and banners properly with the correct hostname. Email is received on all of these instances with no problems and is routed to the correct place. This setup, minus the final instance, has existed for a couple of years and works. I never bothered to set up outbound email to go through any but the main instance, however; there was no need. Now I need to send email from blue.example.us that actually leaves from that interface and IP, such that the Received headers show blue.example.us as the sending mailhost, so that SPF and DKIM validate, etc etc. The email that will be sent from blue.example.com is a feedback loop sent by a single shell account on the server (account5), an account that is dedicated to sending this email. The account receives the feedback loop emails from servers on other networks, saves the bodies of those emails, and then generates a new outbound email header, appends the saved body, and sends the email. It's sending by piping each email to sendmail -oi -t. We're doing it this way to mask the identities of the initial servers. The procmail script that processes these emails works correctly. However, I cannot configure this account to send email through the proper Postfix instance/IP/interface. The exact same account and script sends email through the main Postfix instance /etc/postfix without any issues. When I change MAIL_CONFIG to point to /etc/postfix-blue in either .bash_profile or the Procmail script that handles this email, though, I get this error: sendmail: fatal: User account5(###) is not allowed to submit mail I've read the manuals on Postfix.org, searched Google, and tried the suggestions in three previous answers here on ServerFault.com: Postfix - specify interface to deliver outbound mail on Postfix user is not allowed to submit mail Postfix rejects php mails I have been careful to stop and restart Postfix after each configuration change, and tested the results. Nothing has worked. The main postfix instance happily accepts outbound email from account5. The postfix-blue instance continues to reject email from account5 with the sendmail error above. As tempting as it is to blame machine hostility, I know that I must be missing something or doing something wrong. Does anybody have any suggestions as to what it might be? Please feel free to ask for further information about my setup if you need it. =-=-=-=-=-=-=-=-=-= At the request of the responder, here are main.cf and master.cf for a) the main postfix instance ("red.example.com") and b) the FBL instance ("blue.example.us") [NOTE: All parameters not specified below were left at the default Postfix 2.6 settings] MAIN: master.cf smtp inet n - n - - smtpd main.cf myhostname = red.example.com mydomain = example.com inet_interfaces = $myhostname, localhost inet_protocols = all lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname, localhost.$mydomain, localhost local_recipient_maps = mynetworks = 192.168.34.104/32 relay_domains = example.com, example.info, example.net, example.org, example.us relayhost = [192.168.34.102] # Separate physical server, main mailserver. relay_recipient_maps = hash:/etc/postfix/relay_recipients alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases smtpd_banner = $myhostname ESMTP $mail_name multi_instance_wrapper = ${command_directory}/postmulti -p -- multi_instance_enable = yes multi_instance_directories = /etc/postfix-green /etc/postfix-pink /etc/postfix-orange /etc/postfix-blue FBL: master.cf 184.173.119.103:25 inet n - n - - smtpd main.cf myhostname = blue.example.us mydomain = blue.example.us <= Deliberately set to subdomain only. myorigin = $mydomain inet_interfaces = $myhostname lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname local_recipient_maps = unix:passwd.byname $alias_maps $virtual_alias_maps mynetworks = 192.168.36.51/32, 192.168.35.20/31 <= Second IP is backup MX servers relay_domains = $mydestination recipient_canonical_maps = hash:/etc/postfix-blue/canonical virtual_alias_maps = hash:/etc/postfix-fbl/virtual alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical mailbox_command = /usr/bin/procmail -a "$EXTENSION" DEFAULT=$HOME/Mail/ MAILDIR=$HOME/Mail smtpd_banner = $myhostname ESMTP $mail_name authorized_submit_users = multi_instance_name = postfix-blue multi_instance_enable = yes

  Read the article

• linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

  - by devicerandom

  We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

  Read the article

• Cannot open simplest mac application

  - by streetpc

  I created a very simple app, which is only a wrapper of a shell script (so that I can select this script in application selectors, like startup apps). I try to launch it and yesterday it worked, but today I changed the executable script's content and name (with something that perfeclty works in a shell script launched in the Terminal) and it will only display a Finder-iconed dialog saying Cannot open the application because it is not supported on this kind of Mac. I restored the previous script (content/name) but I still get the error! Same when re-bundling the app from scratch, or completely changing the bundle identifier… If I try to open it in the Terminal using open My.app, I get The application cannot be opened because it has an incorrect executable format. But when I executes directly the Contents/MacOS/Script, it allways works (iwth both contents). Also, it is displayed with correct icon and meta-information in the Finder (so I guess the Info.plist is understood). The app's file tree is: Contents/ Info.plist MacOS/ Script (executable bit set, works when launched directly) PkgInfo Resources/ AppIcon.icns Here is the Info.plist content: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>CFBundleExecutable</key> <string>Script</string> <key>CFBundleIconFile</key> <string>AppIcon</string> <key>CFBundleIdentifier</key> <string>asdf.ScriptApp</string> <key>CFBundleInfoDictionaryVersion</key> <string>6.0</string> <key>CFBundleName</key> <string>My script</string> <key>CFBundlePackageType</key> <string>APPL</string> <key>CFBundleShortVersionString</key> <string>1.0</string> <key>CFBundleSignature</key> <string>????</string> <key>CFBundleVersion</key> <string>1</string> <key>LSMinimumSystemVersion</key> <string>10.4</string> </dict> </plist> And the PkgInfo file only contains APPL????. I tested the Script with a simple echo "ok" and echo "ok" >/tmp/test (plus #!/bin/sh header). So my questions are: * Is there some kind of validity caching for applications ? based on what ? how do I flush it ? * Where does this message come from ? I tried to google it but all I get is a page talking about 32/64 bits Java…

  Read the article

• Can't get IPv6 address using radvd on wireless interface on windows, wired works fine.

  - by AndrejaKo

  I set up my router to use OpenWRT and set it up to use IPv6 using a tunnel form SixXs. I'm having problems with stateless autoconfiguration using radvd. On my computer, wired connection can get its IPv6 address fine, but wireless can't. After spending some time on OpenWRT forums, I'm pretty much sure now that router is set up fine and that the problem is with my windows settings. Also, I do not have any problems getting IPv6 address on openSUSE 11.3. So what should I do to solve this and what information should I post? Here's radvdump output for wired interface: interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition Here's radvdump output for wireless interface: # # radvd configuration generated by radvdump 1.6 # based on Router Advertisement from fe80::a0b7:deff:fef0:5b34 # received by interface br-lan # interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition # # radvd configuration generated by radvdump 1.6 # based on Router Advertisement from fe80::a0b7:deff:fef0:5b34 # received by interface br-lan # interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition

  Read the article

• website connection reset on first load

  - by Tar

  i'm using nginx with php-cgi. lately a problem has arose where if you don't view my site for a while, like 3-4 minutes, and then open it again, the first request you send will return connection reset by peer in the browser. if you refresh, operation is normal for all subsequent requests. this happens every time and it isn't just an isolated incident, it happens to everyone using my site. i've tried to restart nginx and php-cgi but to no avail. does anyone know what the problem could be? i can provide whatever information necessary. it's worth noting that there's nothing in error log besides that message about client closing the connection early. nginx.conf user nobody; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 2048; } http { include /etc/nginx/mime.types; error_page 404 /404.html; error_page 403 /403.html; error_page 444 /444.html; error_page 502 /502.html; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; large_client_header_buffers 8 8k; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 30; server_tokens off; gzip on; gzip_proxied any; gzip_comp_level 6; gzip_buffers 64 8k; gzip_min_length 1024; gzip_http_version 1.1; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; include /etc/nginx/conf.d/*.conf; } default.conf server { listen 80; server_name domain.com; error_log /var/log/nginx/error.log debug; access_log /var/log/nginx/access.log; location / { if ($request_method !~ ^(GET|HEAD|POST)$ ) { return 444; } if ($http_user_agent ~* Havij|hvj|acunetix|wget|HTtrack) { return 403; } root /home/admin06/public_html; autoindex off; index index.php; # Images and static content is treated different location ~* ^.+.(jpg|jpeg|gif|css|png|js|ico|xml)$ { access_log off; expires 30d; root /home/admin06/public_html; } location /nginx_status { stub_status on; access_log off;] deny all; } location ~ \.php$ { fastcgi_split_path_info ^(.+\.php)(/.*)$; #try_files $uri =404; fastcgi_pass backend; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/site/public_html$fastcgi_script_name; include fastcgi_params; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_intercept_errors on; fastcgi_ignore_client_abort off; fastcgi_connect_timeout 60; fastcgi_send_timeout 60; fastcgi_read_timeout 60; fastcgi_buffer_size 128k; fastcgi_buffers 4 256k; fastcgi_busy_buffers_size 256k; fastcgi_temp_file_write_size 256k; } ## Disable viewing .htaccess & .htpassword location ~ /\.ht { deny all; } location ~ error_log { deny all; } location ~ access_log { deny all; } location ~ \.cgi { deny all; } location ~ \.db { deny all; } }

  Read the article

• Debian dependency problems / partially installed

  - by Michael

  I tried to install curl support for php 5 on my debian squeeze machine and since I'm having problems. After trying to install curl I got dependency issues which I tried to solve by removing what started the issues. From one thing came another and I'm currently looking at ~29 issues when I try to do an apt-get upgrade. These issues vary from unable to config, dependency and unable to remove errors. I tried apt-get upgrade -f and installing packages using dpkg command. I tried removing using purge and force. I manually removed stuff to try and fix it. I tried running dpkg --configure -a. I've to say I'm still pretty new to linux so I'm out of idea's and cant seem to find an answer online that matches my problems. Here's a part of the apt-get upgrade command output: Reading package lists... Building dependency tree... Reading state information... 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 29 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up libgeoip1 (1.4.7~beta6+dfsg-1) ... Bus error dpkg: error processing libgeoip1 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libisc62 (1:9.7.3.dfsg-1~squeeze3) ... Bus error dpkg: error processing libisc62 (--configure): subprocess installed post-installation script returned error exit status 135 dpkg: dependency problems prevent configuration of libdns69: libdns69 depends on libgeoip1 (>= 1.4.7~beta6+dfsg); however: Package libgeoip1 is not configured yet. libdns69 depends on libisc62; however: Package libisc62 is not configured yet. dpkg: error processing libdns69 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libisccc60: libisccc60 depends on libisc62; however: Package libisc62 is not configured yet. dpkg: error processing libisccc60 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libisccfg62: libisccfg62 depends on libdns69; however: Package libdns69 is not configured yet. .. continues Errors were encountered while processing: libgeoip1 libisc62 libdns69 libisccc60 libisccfg62 libbind9-60 liblwres60 bind9-host libavahi-core7 libdaemon0 avahi-daemon libexif12 libffi5 libgomp1 libgphoto2-port0 libgphoto2-2 libperl5.10 libsensors4 libsnmp15 libhpmud0 libieee1284-3 libnss-mdns libossp-uuid16 libpq5 libv4l-0 libsane libsane-hpaio libssh2-1 python-gobject dpkg --configure -a Setting up libpq5 (8.4.8-0squeeze2) ... Bus error dpkg: error processing libpq5 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libperl5.10 (5.10.1-17squeeze2) ... Bus error dpkg: error processing libperl5.10 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libffi5 (3.0.9-3) ... Bus error dpkg: error processing libffi5 (--configure): subprocess installed post-installation script returned error exit status 135 Setting up libexif12 (0.6.19-1) ... .. continues Suggestions are really welcome I really don't know what to do. Michael.

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• "Service Unavailable" when browsing to static HTML page in non-application IIS website on Windows 2003 (possibly SharePoint WSS 2.0 related?)

  - by Jordan Rieger

  Background: My client has an old Pentium III Windows 2003 server whose 16/36 GB disks are dying. On it he has a database-driven web site and email application that needs further customization by a developer (me). First we need to get it working on the new server. The original developer is no longer available to provide a system setup guide. So my client got a tech who imaged the old drives over to the new server and managed to get it booting. But the IIS-driven site no longer works. In fact it seems that IIS itself does not work. Problem: Service Unavailable when attempting to browse from the server itself to the URL for a local Web Site called test which I setup in IIS to serve a single static index.htm file. This I did to isolate the problem, and eliminate the client's application from the equation. The site is setup on port 80 with the host header "test.myclientsdomain.com", and I used the etc\hosts file to point that host at the local IP. I know the host entry took effect because I can ping it. When doing an iisreset, I get: Attempting start... Restart attempt failed. IIS Admin Service or a service dependent on IIS Admin is not active. It most likely failed to start, which may mean that it's disabled. Despite this message, the services all stay in the Started state. The only relevant System event logs I found are: Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1002 Date: 11/4/2012 Time: 11:04:47 PM User: N/A Computer: ALPHA1 Description: Application pool 'DefaultAppPool' is being automatically disabled due to a series of failures in the process(es) serving that application pool. Event Type: Error Event Source: W3SVC Event Category: None Event ID: 1039 Date: 11/4/2012 Time: 11:13:12 PM User: N/A Computer: ALPHA1 Description: A process serving application pool 'DefaultAppPool' reported a failure. The process id was '5636'. The data field contains the error number. Data: 0000: 7e 00 07 80 ~.. And one Application event log: Event Type: Error Event Source: Windows SharePoint Services 2.0 Event Category: None Event ID: 1000 Date: 11/4/2012 Time: 11:34:04 PM User: N/A Computer: ALPHA1 Description: #50070: Unable to connect to the database STS_Config on ALPHA2\SharePoint. Check the database connection information and make sure that the database server is running. That last log tells me that the tech may have initially tried to have both the old and the new server running, by renaming the new server from ALPHA1 to ALPHA2. And perhaps SharePoint grabbed onto that change, and now can't tell that the machine name has been switched back to the old ALPHA1. But why would SharePoint interfere with a static IIS web site serving a single HTML file? The test site is not even within an Application pool (I clicked the Remove button.) What I have tried/eliminated: No relevant services seem to be disabled: IIS Admin, WWW Publishing, Sharepoint Timer Giving Full Control to All Users/Everyone on the c:\inetpub\test folder serving my test site. I can connect to and query the local SharePoint config database (ALPHA1\SHAREPOINT\STS_CONFIG) from SSMS. But when I try to do stsadm -o setconfigdb -connect -databaseserver ALPHA1\SHAREPOINT it tells me The SharePoint admininstration port does not exist. Please use stsadm.exe to create it. And when I do that, using the port 9487 specified in the IIS SharePoint Admin site config, it tells me the port is already in use. Needless to say, simply browsing to the admin site gives me a similar error about being unable to reach the config database. I didn't want to go further down the SharePoint path as it may be completed unrelated to my IIS issue, and I don't even know yet if SharePoint is required for this application to work. The app itself is ASP.Net/C#/Silverlight and a little MS Word integration (maybe that's where the SharePoint stuff comes in.)

  Read the article

• Rosewill RSV-S5 and it's transferespeeds

  - by DoomStone

  I have just bought a Rosewill RSV-S5, I have installed 5x1,5Tb Western Digital Green disks in it. After that have I created a Raid5 on them all with the software that followed with the hardware. Not the raid it self works fine, but it is SLOW, I can only obtain a maximum of 25 MB/s, and if SABnzbd+ is downloading with 5 MB/s is it having a hard time streaming a normal DIVX (700 mb) movie. Is this normal or is there something wrong? Edit: should be able to handle 3 Gbps = 384 megabytes / second Edit 2: As you can see am I only downloading with 3,76 MB/s and I'm trying to watch V s02e08 (720p), but it is completely unwatchable, as I can see 30 sec, and the it buffers for 20 sec. Edit: Other information there might be required I'm running Windows Server 2008 R2, optimized for program performance. Windows is installed on a 60GB SSD. I have a 50 Mb/s internet connection and a 1 Gb/s LAN, all connected with Cat6 Ethernet cables. The MCE is using a Gigabyte EP35C-DS3R motherboard with 2 GB DDR2 ram. Edit 3: I have used chunk sizes for 128 KB Edit 4: I found this on newegg Pros: Enclosure for 5x2TB hard drive is fine. This is basically a rebranded San Digital TR5M-B product. For support Rosewill tells you to contact San Digital. No direct support from Silicon Image for the computer raid card. Cons: Includes computer Silicon Image 3132 raid card, extremely slow raid 5 write (our tests ~10MB/s). Compare to regular internal local drive write 30-60MB/s. We basically dumped the Sil3132 card and replaced with High Point RocketRaid 622 card for extra $69.99. Note for RR622, turn off ECRC (end to end CRC check) for card to work on IBM xserver. What took 12hrs to copy now took 2-3hrs. San Digital realized the problem and has the newer model TR5M-BP TowerRaid Plus that comes with High Point RocketRaid 622 card. Rosewill should discontinue this product and go with TR5M-BP. Could not get Silicon Image raid management software to work with complicated 2008R2 server with 10 NICs, application doesn't know how to talk to localhost port with all those NICs. No updates from Silicon Image and support from San Digital ignored. Gave up on Sil3132 card. Save yourself from a lot of headaches, get the RR622 card too if you are going to buy this product. Other Thoughts: The newer model is TR5M-BP TowerRaid Plus, comes with High Point RocketRaid 622 raid card for the PC instead of Silicon Image Sil3132. According to San Digital, raid 5 performance for Sil3132 read 80MB/s write 19MB/s, and RR622 read 154MB/s write 149MB/s. Our RR622 tests gave (8TB raid 5) write ~80-110MB/s copying 40GB file took 8mins. So I have now ordered a HighPoint RocketRAID 622 2P ext SATA III and hopes that it will solve my problems.

  Read the article

• Identifying the cause of my DNS failure (domain not propagating)

  - by thejartender

  I have set up a DNS server with the help of two helpful tutorials: http://linuxconfig.org/linux-dns-server-bind-configuration http://ulyssesonline.com/2007/11/07/how-to-setup-a-dns-server-in-ubuntu/ I am using: Ubuntu Bind9 and had issues I tried negating on my own thanks to a question I posted here earlier that pointed out my mistake of using rfc 1918 addresses in my previous SOA record: $TTL 3D @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. $TTL 600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.10.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I read the ranges that are used under rfc 1918 and modified my routers resource pool to assign LAN devices IP(s) within the 30.0.0.0 range and now modified my SOA to: $TTL 600 @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 30.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 30.0.0.42 gw IN A 30.0.0.138 www IN CNAME thejarbar.org. $TTL600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.30.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I can ping my nameserverver ns.thejarbar.organd it gives me the correct isp IP address, but my domain never seems to propagate to my nameserver. I have searched for a concise tutorial that covers setting up a DNS with a nameserver that hosts (my) or the site. I am fully aware that this is not recommended and am using this for my learning purposes. Getting to the question, due to the lack of information in tutorials I looked at (nothing about rfc 1918 and no example of swapping these with ISP IP) is my router modification going to help me as it does not seem to be. I have also tried as recommended using my ISP IP instead of the values I posted. My site never propagated to my nameserver. What could be causing this? I have run dig thejarbar.org @88.89.190.171 and get an authorative response. Can anyone assist me with the final steps I may be missing here?

  Read the article

• Make exact mp4 (H264) format for uploading to youtube

  - by WHITECOLOR

  With ffmpeg I'm converting video from mp3 and picture to upload it to youtube. After upload, conversion fails. Reasons are unknown. I believe the problem is in format. By the way If I'm uploading file 5 minutes length, it fails if I upload 30 seconds of this file it succeeds. I have donwload mp4 file from youtube. Then I uploaded it, it is done very fast. So a nice solution would be to convert videos to the same format that is done by google. I got the following output by mpeg: ffmpeg version N-44264-g070b0e1 Copyright (c) 2000-2012 the FFmpeg developers built on Sep 7 2012 17:38:57 with gcc 4.7.1 (GCC) configuration: --enable-gpl --enable-version3 --disable-pthreads --enable-runt ime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass - -enable-libcelt --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-l ibfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenj peg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheo ra --enable-libutvideo --enable-libvo-aacenc --enable-libvo-amrwbenc --enable-li bvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --ena ble-zlib libavutil 51. 72.100 / 51. 72.100 libavcodec 54. 55.100 / 54. 55.100 libavformat 54. 25.105 / 54. 25.105 libavdevice 54. 2.100 / 54. 2.100 libavfilter 3. 16.100 / 3. 16.100 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 15.100 / 0. 15.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'youtubetrack0.mp4': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: isommp42 creation_time : 2012-10-02 22:58:57 Duration: 00:06:46.66, start: 0.000000, bitrate: 176 kb/s Stream #0:0(und): Video: h264 (Constrained Baseline) (avc1 / 0x31637661), yu v420p, 450x360, 78 kb/s, 6 fps, 6 tbr, 12 tbn, 12 tbc Metadata: creation_time : 1970-01-01 00:00:00 handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 95 kb/s Metadata: creation_time : 2012-10-02 22:58:57 handler_name : IsoMedia File Produced by Google, 5-11-2011 Is it possible to construct ffmpeg parameters so that that would give the same format that google internally does? Is the information above sufficient? I couldn't construct needed params. For example I don't understand how to set tbn and what 95 kb/s mean in "Stream #0:1(und): Audio:". Now I just do: ffmpeg -i videoimage.jpg -i audio.mp3 video.mp4 Info I've got: ffmpeg version N-44998-gdf82454 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 2 2012 23:03:12 with gcc 4.7.1 (GCC) configuration: --disable-static --enable-shared --enable-gpl --enable-version3 --disable-pthreads --enable-runtime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass --enable-libcelt --enable-libopencore-amrnb --en able-libopencore-amrwb --enable-libfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenjpeg --enable-librtmp --enable-libschroedinger - -enable-libspeex --enable-libtheora --enable-libutvideo --enable-libvo-aacenc -- enable-libvo-amrwbenc --enable-libvorbis --enable-libvpx --enable-libx264 --enab le-libxavs --enable-libxvid --enable-zlib libavutil 51. 73.101 / 51. 73.101 libavcodec 54. 63.100 / 54. 63.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'video.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2avc1mp41 encoder : Lavf54.25.105 Duration: 00:06:46.81, start: 0.000000, bitrate: 129 kb/s Stream #0:0(und): Video: h264 (High) (avc1 / 0x31637661), yuvj420p, 450x360, 3392 kb/s, 25 fps, 25 tbr, 25 tbn, 50 tbc Metadata: handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 127 kb/s Metadata: handler_name : SoundHandler This video fails the conversion on youtube. I also tried to use other vcode parmam and extensions of output file (mp4, wmv, avi) but failed too. Would be greatful for help.

  Read the article

< Previous Page | 935 936 937 938 939 940 941 942 943 944 945 946  | Next Page >