Search Results

Search found 3140 results on 126 pages for 'debian'.

Page 94/126 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• Remote Software Solution that Acts as a Client

  - by Richard

  I am looking for something that I am not sure exists. I have a remote computer that will not allow incoming traffic due to ISP blocking of ports(basically double NAT situation that I am unable to get around). I am wondering if I have a computer acting as a client, is there any solution out there that will allow remote access to the computer. I do have other servers on the net that have static IP's that the computer could initiate a connection with. I am thinking of using Debian Linux, However computer is not built yet so OS is not overly important at this point.

  Read the article

• Xmodmap configuration

  - by Krishna S

  On my Debian Linux machine Ctrl+Alt+F1 is bound to a virtual terminal. I can see the corresponding entry by running xmodmap -pke keycode 67 = F1 XF86_Switch_VT_1 F1 XF86_Switch_VT_1 Per this thread, which I might add is consistent with what I've read elsewhere, the columns on the right hand side of = correspond to key, Shift+key, AltGr+key and Shift+AltGr+key. Given that, I don't understand how the keycode mapping for F1 (above) works for Ctrl+Alt+F1. It seems it should really be either Shift+F1 or Shift+AltGr+F1? Here's the output of xmodmap -pm on my machine: shift Shift_L (0x32), Shift_R (0x3e) lock Caps_Lock (0x25) control Control_L (0x42), Control_R (0x69) mod1 Alt_L (0x40), Alt_R (0x6c), Meta_L (0xcd) mod2 Num_Lock (0x4d) mod3 mod4 Super_L (0x85), Super_R (0x86), Super_L (0xce), Hyper_L (0xcf) mod5 ISO_Level3_Shift (0x5c), Mode_switch (0xcb) Can anybody explain it?

  Read the article

• rsync osx to linux

  - by Nick

  I did a backup to a remote nfs folder with rsync, from a MAC to a Remote Debian. The final backup is 58GB less than the original. Rsync says that everything was OK, and nothing to update. Macintosh:/Volumes/Data1 root# du -sh Produccion/ 319G Produccion/ root@Disketera:/mnt/soho_storage/samba/shares# du -sh Produccion/ 260G Produccion/ can I trust in rsync? I'm using rsync -av --stats /Volumes/Data1/Produccion/ /mnt/red/ (/mnt/red is my samba mountpoint) Some differents folders root@Disketera:/mnt/soho_storage/samba/shares/Produccion/tiposok# du -sh * 0 IndoSanBol 0 IndoSans-Bold 0 IndoSans-Italic 0 IndoSans-Light 0 IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 12K TCL IndoSans_mac Macintosh:/Volumes/Data1/Produccion/tiposok root# du -sh * 36K IndoSanBol 40K IndoSans-Bold 36K IndoSans-Italic 36K IndoSans-Light 36K IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 160K TCL IndoSans_mac

  Read the article

• Best practice, or generally best way to set up web-hosting server, permissions, etc.

  - by Jagot

  Hi, I'm about to set up a server upon which a friend and I will be hosting web sites, and I'll be using Debian. I've set up a LAMP solution many times just to using for local testing purposes, but never for actual production use. I was wondering what are the best practices are in terms of setting the server up, in reference specifically to accessing the web root directory. A couple of the options I have seen: Set up a single user account on the server for us both to use and use a virtual host to point to the somewhere in the home directory, e.g. /home/webdev/www. Set each of us up a user account, and grant permissions in some way to /var/www (What would be the best way? Set up a new group?) I want to get this right when I first set this up as there won't be any going back for a while once our first site is up and running. Appreciate any guidance in advance.

  Read the article

• Server suddenly running out of entropy

  - by Creshal

  Since a reboot yesterday, one of our virtual servers (Debian Lenny, virtualized with Xen) is constantly running out of entropy, leading to timeouts etc. when trying to connect over SSH / TLS-enabled protocols. Is there any way to check which process(es) is(/are) eating up all the entropy? Edit: What I tried: Adding additional entropy sources: time_entropyd, rng-tools feeding urandom back into random, pseudorandom file accesses – netted about 1 MiB additional entropy per second, problems still persisted Checking for unusual activity via lsof, netstat and tcpdump – nothing. No noticeable load or anything Stopping daemons, restarting permanent sessions, rebooting the entire VM – no change in behaviour What in the end worked: Waiting. Since about yesterday noon, there are no connection problems anymore. Entropy is still somewhat low (128 Bytes peak), but TLS/SSH sessions have no noticeable delay anymore. I'm slowly switching our clients back to TLS (all five of them!), but I don't expect any change in behavior now.

  Read the article

• How to configure installed Ruby and gems?

  - by NARKOZ

  Hi. My current gem env returns: RubyGems Environment: - RUBYGEMS VERSION: 1.3.6 - RUBY VERSION: 1.8.7 (2008-08-11 patchlevel 72) [x86_64-linux] - INSTALLATION DIRECTORY: /home/USERNAME/.gems - RUBYGEMS PREFIX: /home/narkoz - RUBY EXECUTABLE: /usr/bin/ruby1.8 - EXECUTABLE DIRECTORY: /home/USERNAME/.gems/bin - RUBYGEMS PLATFORMS: - ruby - x86_64-linux - GEM PATHS: - /home/USERNAME/.gems - /usr/lib/ruby/gems/1.8 - GEM CONFIGURATION: - :update_sources => true - :verbose => true - :benchmark => false - :backtrace => false - :bulk_threshold => 1000 - "gempath" => ["/home/USERNAME/.gems", "/usr/lib/ruby/gems/1.8"] - "gemhome" => "/home/USERNAME/.gems" - REMOTE SOURCES: - http://rubygems.org/ How can I change path /home/USERNAME/ to my own without uninstalling? OS: Debian Linux

  Read the article

• Corrupt mysql system tables

  - by psynnott

  I am having issues with the columns_priv table in the mysql system database. I cannot add new users currently. I have tried repairing it using mysqlcheck --auto-repair --all-databases --password but I get the following output: mysql.columns_priv Error : Incorrect file format 'columns_priv' error : Corrupt Is there any other way to repair this table, or how do I go about replacing it with a blank table? What would I lose by doing that? Thank you Edit (Additional Info) mysqld is currently using 100% cpu constantly. Looking at show processlist, I get: mysql> show processlist; +-----+------------------+-----------+-------+---------+------+-------------------+------------------------------------------------------------------------------------------------------+ | Id | User | Host | db | Command | Time | State | Info | +-----+------------------+-----------+-------+---------+------+-------------------+------------------------------------------------------------------------------------------------------+ | 5 | debian-sys-maint | localhost | mysql | Query | 1589 | Opening tables | ALTER TABLE tables_priv MODIFY Column_priv set('Select','Insert','Update','References') COLL | | | 752 | root | localhost | NULL | Query | 0 | NULL | show processlist | +-----+------------------+-----------+-------+---------+------+-------------------+------------------------------------------------------------------------------------------------------+ 2 rows in set (0.00 sec)

  Read the article

• Very high memory usage, but not claimed by any process?

  - by SharkWipf

  While stress-testing LVM on one of our Debian servers, I came across this issue where memory would fill up a lot to the point where it would run the server out of memory, but no process would claim the memory. See http://i.imgur.com/cLn5ZHS.png, and see http://serverfault.com/a/449102/125894 for an explanation on the colors used in htop. Why is this happening? And is there any way to see what process is using the memory? Htop is configured not to hide any processes, so what is it that htop is missing? In this particular case, I can fairly certainly say that it is caused, directly or indirectly, by lvmcreate, lvmremove or dmsetup, as I was stress-testing that. Do note that this question is not about solving the LVM problem, but about why the memory isn't claimed by any process. Stopping all LVM commands does bring the memory back down to <600MB.

  Read the article

• Apache worker is crashing after 3.000 users

  - by user1618606

  I activated Apache Worker on my VPS and I'm having problems, 'cause the website is crashing when 3000 users are accessing the website. I'm using http://whos.amung.us/stats/2jzwlvbhvpft/ as counter. My Apache Worker configuration: KeepAlive On MaxKeepAliveRequests 0 KeepAliveTimeout 1 <IfModule mpm_worker_module> ServerLimit 20000 StartServer 8000 MinSpareThreads 10400 MaxSpareThreads 14200 ThreadLimit 5 ThreadsPerChild 5 MaxClients 20000 MaxRequestsPerChild 0 </IfModule> The VPS have the SO: Debian 64 LAMP, memory: 14gb and CPU: 24ghz What I could to do to give a best performance?

  Read the article

• Qemu in an ssh session or the quest for the nographic option ?

  - by LB

  Hi, I ssh to a machine and I would like to start a qemu session inside this ssh session. I thought that the nographic option would do the trick. -nographic Normally, QEMU uses SDL to display the VGA output. With this option, you can totally disable graphical output so that QEMU is a simple command line application. The emulated serial port is redirected on the console. Therefore, you can still use QEMU to debug a Linux kernel with a serial console. but unfortunately, i don't see any output. The command line that i'm using once i've sshed to my machine is : qemu-system-x86_64 -hda debian.img -nographic any idea ? thanks.

  Read the article

• Keepalived with apache unable to bind interface on Backup server

  - by davideagle

  I have two debian 6 servers running keepalived 1.1.20 with one server acting as a Master and the other as a Backup. Both servers host apache 2.4 that have a global Listener on all interfaces on port 80 (Listen *:80) how ever I have some sites that require a listener for port 443 (SSL) and that is configured for each VirtualHost in the Apache config since I do not want every VirtualHost to listen on port 443. The problem is when I try to start Apache on the Backup machine that does not hold the virtual interface the VirtualHost is supposed to be listening on, I get AH00072: make_sock: could not bind to address 1.1.1.1:443. I know this is expected behavior of Apache. The real question is are there any known workarounds or solutions to this scenario?

  Read the article

• Throttling apache downloads selectively

  - by Synchro

  I have a linux box running Debian Sarge (old I know) and apache 2.0.54. It serves two kinds of files - regular web pages and small images, and a lot of large podcast mp3s. The podcast downloads swamp the connection and make the rest of the site unresponsive, so I'm looking to throttle the data transfer rate (not the request rate) of just the podcasts. I've set up haproxy using this technique which does what it says it will, but solves a different problem - even only 5 simultaneous podcast downloads is enough to saturate the link. In a perfect world, haproxy would support per-connection throttling, but it doesn't. So far I've looked at mod_bw (won't compile for me, seems unsupported), mod_cband (unsupported, widely reported as problematic) and iptables using tc. The iptables approach would allow me to throttle things, but would not be at all selective, slowing down everything on the server, not just the podcasts, so would just move the bottleneck without changing overall behaviour. Ideas?

  Read the article

• central log-server with auditdisp

  - by johan

  I want to setup a central log-server. The log-server is running with debian 6.0.6 and the audit daemon is installed in version 1.7.13-1. The Clients are running with Red Hat 5.5 and they connect to the log-server via audispd. The connection works fine and i get all messages from each node. My questions is: is it possible that the auditd daemon from the log server write the messages from each node in a separate file? I try to transfer the messages via the syslog daemon, that works but i can not use tools like ausearch to analyze these log-files.

  Read the article

• Openfire Installation Issue - Can't Login to admin panel

  - by Lobe

  I am trying to get Openfire to install on an Ubuntu virtual machine, however upon completing the web based installer, I am unable to login to the admin panel. So far I: downloaded Debian installer Installed using stock options Added database and built the structure using supplied SQL file Completed web based installer I am now trying to login using username: admin and my password, however I constantly get a wrong username/password error. There is a record generated in the MySQL database showing the admin user with an encrypted password, and changing to an unencoded password doesn't work. What is the problem here?

  Read the article

• How to setup a fast VPN server

  - by Saif Bechan

  I am trying to set up a VPN that has a fast download speed. The server I have is a linux server and from there I can download 2 megabytes a second. At home I can also download with 2 megabytes a second. All the downloads I do are from the same source, no different server. Now I have set up a VPN connection between my home and the server, and now I am only downloading 64 kilobytes a second! The connection I have created is a PPTP server on a debian machine. Now my question is if it is possible to optimize this connection. Should I maybe switch to OpenVPN, or change operating systems? Or are there some kind of settings to tweak to make the connection optimal. PS. The server I am running is on a XEN node. I have done the proper ip forwarding.

  Read the article

• Linux - Block ssh users from accessing other machines on the network

  - by Sam

  I have set up a virtual machine on my network for uni project development. I have 6 team members and I don't want them to SSH in and start sniffing my network traffic. I already have set the firewall on my W7 pcs to ignore any connection attempts from the Virtual Machine, but would like to go a step further and not allow any network access from the VM to other machines on my network. Team members will be access the VM by SSH. The only external port forwarded is to vm:22. The VM is running in VirtualBox on a bridged network connection. Running latest Debian. If someone could tell me how to do this I would be much obliged.

  Read the article

• Why is the size of windows off by 226x238 if defined via the Window Rules?

  - by Bobby

  I have installed Sawfish 1.8.2 from source on my new Ubuntu 12.04 installation following the Debian instructions, but I had this problem also with the stock 1.5.3. Whenever I define dimensions in the Window Rules for a window, the size is off by exactly 226x238 pixels, which means that 100x100 turns into 326x328. That's a very odd behavior, given that Sawfish is saving and loading the dimensions of the windows correctly (if saved via the window menu). Some additional system information: $ uname -a Linux Dagon 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux $ sawfish --version sawfish version 1.8.2 nvidia proprietary driver, 9600GT Two monitors, 1920x1080 + 1440x900 in one session. Positionng the windows is working fine, only the dimensions are off by that odd number. Does somebody have an idea why?

  Read the article

• WebSVN accept untrusted HTTPS certificate

  - by Laurent

  I am using websvn with a remote repository. This repository uses https protocol. After having configured websvn I get on the websvn webpage: svn --non-interactive --config-dir /tmp list --xml --username '***' --password '***' 'https://scm.gforge.....' OPTIONS of 'https://scm.gforge.....': Server certificate verification failed: issuer is not trusted I don't know how to indicate to websvn to execute svn command in order to accept and to store the certificate. Does someone knows how to do it? UPDATE: It works! In order to have something which is well organized I have updated the WebSVN config file to relocate the subversion config directory to /etc/subversion which is the default path for debian: $config->setSvnConfigDir('/etc/subversion'); In /etc/subversion/servers I have created a group and associated the certificate to trust: [groups] my_repo = my.repo.url.to.trust [global] ssl-trust-default-ca = true store-plaintext-passwords = no [my_repo] ssl-authority-files = /etc/apache2/ssl/my.repo.url.to.trust.crt

  Read the article

• HFS partition mounting read-only

  - by Sid

  Hey, I have an external Western Digital Hard drive with two HFS partitions with journaling disabled. When I connect it to a computer running Linux (Debian or Ubuntu), frequently both partitions are mounted read-only. In the past, mounting them on my Macbook and executing the command to disable the journaling often worked (even though it would tell me that journaling was already disabled) but I would love to have a solution which works every time. Thanks! Edit: In light of Chris Johnsen's comment below - my question is how to mount the filesystem read+write on Linux since it is not automatically doing so itself

  Read the article

• The cache is getting at full level so fast

  - by CompilingCyborg

  Please, the memory and the cache are getting to the full level quite quickly under my linux mint 9 - isadora system. I used Ubuntu and Debian before, and it was not causing this issue at all. At the current time i typing the following command frequently to empty the cache "echo 3 /proc/sys/vm/drop_caches". Please any way around this? or do you know what's going wrong? | I am only programming on this machine; no graphics, no games nothing. Thanks in advance for your help!

  Read the article

• Entire filesystem restore from rdiff-backup snapshot

  - by atmosx

  I'm trying to make a complete system restore from an rdiff-backup. The cli for backing was: rdiff-backup --exclude-special-files --exclude /tmp --exclude /mnt --exclude /proc --exclude /sys / /mnt/backup/ebox/ I created a new partition mounted the partition at /mnt/gentoo and did: rdiff-backup -r /mnt/vol2 /mnt/gentoo However when I try to chroot to this system (following gentoo's manual, which means mounting /dev/ and /proc) I get the following error: chroot: failed to run command/bin/bash': No such file or directory` All this takes place on a Parallels (virtual machine) Debian installation. Any ideas on how to proceed in order to fully restore the system? Best Regards ps. /mnt/gentoo/bin/bash works fine if I execute it. All files and permissions are in place rdiff-backup seems to work just fine. However the system cannot neither boot (exits with kernel panic - cannot find init) or be chrooted.

  Read the article

• How to bulk-rename files with invalid encoding or bulk-replace invalid encoded characters?

  - by qdoe

  I have a debian server and I'm hosting music for an internet radio station. I have trouble with file names and paths because a lot of files got an invalid encoding, for example: ./music/Bändname - Some Title - additional Info/B?ndname - 07 - This Title Is Cörtain, The EncÃ?ding Not.mp3 Ideally, I would like to remove everything that is not letters A-Z/a-z or numbers 0-9 or dash -/underscore _... The result should look like something like that: ./music/Bndname-SomeTitle-additionalInfo/Bndname-07-ThisTitleIsCrtain,TheEnc?dingNot.mp3 How to achieve this for a batch of a lot of files and directories? I've seen this similar question: bulk rename (or correctly display) files with special characters But this only fixes the encoding, I would prefer a more strict approach as described above.

  Read the article

• Using slapcat to backup LDAP

  - by rsw

  I'm running an OpenLDAP directory on a Debian server, using the hdb backend. I've been wondering about backups, and did som reading on the net. Slapcat seems to be the way to go, but I keep seeing these posts speaking about it being dangerous to use it while slapd is running. In what way is this dangerous? I'm planning to run these backups during the night, and no writing will be done to the database during the night - reads will probably occur though. If there's any other backup solution better suited for this, I'd gladly hear about it.

  Read the article

• ftp server over internet using different port

  - by ???? ????

  I want to make my ftp server over the internet i made it on Debian linux computer and i changed the port of it to 201 my local ip is 192.168.1.3 so i can access it from any computer on my network through ftp :// mylocalip:201 it appear to me the login page i login with my linux user and can see the files on my ftp server to make it public i make port mapping on my router for port 201 when i try ftp :// mypublicip:201 it give me the login page and when i entered the login data it is loading infinity without open my ftp server files when i made it over default port 21 it works fine. can any one tell me what is the problem here?

  Read the article

• CPU and HD degradation on sourced based Linux distribution

  - by danilo2

  I was wondering for a long time if source based Linux distributions, like Gentoo or Funtoo are "destroying" your system faster than binary ones (like Fedora or Debian). I'm talking about CPU and hard drive degradation. Of course, when you're updating your system, it has to compile everything from source, so it takes longer and your CPU is used at hard conditions (it is warmer and more loaded). Such systems compile hundreds of packages weekly, so does it really matter? Does such a system degrade faster than binary based ones?

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >