Search Results

Search found 5756 results on 231 pages for 'cpu utilization'.

Page 95/231 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102 | Next Page >

Why is my second monitor not working?

- by StampedeXV

Since I have my new computer, I have a very weird problem. Facts: New Computer: Motherboard: ASRock Z77 Pro 3 Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i5-3570 Windows 7 64bit 500W beQuiet special edition (92% efficiency) 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 2 2 magnetic HDDs + 1 SDD 1 DVD-R Old Computer: Motherboard: Asus P55 something Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i7-870 Windows 7 64bit 550W Corsair 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 3 2 magnetic HDDs + 1 SDD 1 DVD-R On the old computer it worked fine with two monitors. Moving to the new (I took the same Graphics-card) it only works with one. The weird thing I mentioned is: not matter which one. But if I put both there, only one is available. There is no reaction at the start (where normally (at least if I remember correctly) the monitor shortly went from "standby" to "on"). Windows does not recognize a second monitor in the Device Manager. I have the latest drivers for Motherboard and Graphics-card. I have the latest BIOS drivers. I am out of ideas. Edit: completed computer setup

Read the article
PC can't detect second RAM installed

- by kulwinder

I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

Read the article
Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

- by Wesley

Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

Read the article
How can Nagios handle non-threshold based plugins?

- by FliesLikeABrick

I am writing a Nagios plugin to monitor trends of a certain storage resource utilization (e.g. gradual increases are fine, but an instantaneous/sudden increase or decrease in resource usage may indicate a problem). For what it's worth, it is reviewing the last N entries in an RRD file generated by a custom cacti data source/templates. What is the "right" way to handle Nagios notification config/implementation for this? The problem is that it the plugin would exit as warning/critical for one polling period, but in the next it would be fine (or 3 polling periods later, if I look at 3 polling periods worth of data). I guess the question is: should I just write it in such a way that it will alert for X polling periods, or should I find a way to write it such that manual intervention is required for it to clear (such as logging into the monitoring server or hitting a URL to run a script that submits a passive result)? Your input is appreciated, and if you have any tips for how to implement the latter I'm open to them (I can think of a few ways to possibly implement it)

Read the article
Constant crashes in windows 7 64bit when playing games

- by yx

I've tried everything I can possibly think of in trying to fix this problem and I'm totally out of ideas, so any help would be appreciated: The problem: whenever I fire up a game, it works for a short while with no problems and then it would crash. Either its a hard crash, forcing me to reboot, or windows would report that the display driver has stopped working and recovered. Here is a list of things I've already tried: Drivers - tried the latest drivers (catalyst 9.12) as well as the stock drivers that came with the video card. Also have the latest BIOS/chipset Memtest - Ran Memtest86+ overnight, had no problems, the windows diagnostic tool also does not find any problems. Overheating - Video card/cpu temperatures are well below peak (42 and 31 Celsius receptively) PSU Voltage - CPUID shows that the voltage levels are all above what they should be. The PSU itself is only roughly 16 months old and is a good model. HDD - No errors when checked GPU - Brand new (replaced previous card since I thought it was the problem, apparently not) Overclocking - Everything is at stock levels, memory voltage is set to manufacturer's standard Specs: Motherboard: ASUS P5Q Pro CPU: Core 2 Duo E8400 3.0 ghz OS: Windows 7 home premium 64 bit Memory: Mushkin Enhanced 4GB DDR2 GPU: Sapphire HD 5850 1GB PSU: SeaSonic M12 600W ATX12V DirectX: DX11 Event Viewer after a crash always has these logged: A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 1 The details view of this entry contains further information. A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Bus/Interconnect Error Processor ID: 0 The details view of this entry contains further information. A previous card that I had (4850x2) also had these errors, so I changed video cards, but the same thing is happening.

Read the article
No clue for high load average on top

- by Oz.

We have several machines on Amazon (ec2) of the type c1.xlarge with 16 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st(see below). Mem is about 1.5GB free. Any idea what could it be, or where else can we check? Many thanks for the help. # # top # top - 07:57:42 up 4:18, 1 user, load average: 1.36, 1.45, 1.47 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu(s): 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 7120092k total, 5644920k used, 1475172k free, 532888k buffers Swap: 0k total, 0k used, 0k free, 3463936k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1557 mysql 20 0 1829m 374m 6448 S 14.3 5.4 11:15.09 mysqld 6655 apache 20 0 416m 49m 3744 S 9.3 0.7 0:04.85 httpd 27683 apache 20 0 421m 54m 3708 S 9.0 0.8 0:00.99 httpd 6682 apache 20 0 424m 57m 3788 S 8.3 0.8 0:03.81 httpd 16816 apache 20 0 419m 51m 3760 S 4.3 0.7 0:04.09 httpd 22182 apache 20 0 417m 50m 3756 S 1.7 0.7 0:06.34 httpd 219 root 20 0 0 0 0 S 0.3 0.0 0:00.34 kworker/7:1 699 root 20 0 0 0 0 S 0.3 0.0 0:00.40 kworker/3:1 1 root 20 0 19376 1508 1212 S 0.0 0.0 0:00.29 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0.0 0.0 0:00.71 ksoftirqd/0

Read the article
Is the exhaust fan necessary?

- by Borek

On my new PC, the component making the most noise is the rear exhaust fan on my case (it is the only exhaust fan in my PC). I tried to disconnect it and watched temperatures in SpeedFan and CPU was usually at about 35C, peaking to about 50C when the system was under load - this doesn't look too bad. So I'm considering that I'll leave the exhaust fan disconnected permanently after which the computer is very quiet - the only noise-making components are Arctic Cooling Freezer 7 Pro Rev.2 (CPU fan) and PSU fan (Enermax Pro 82+), both being quiet enough as far as I can tell. (My GPU has a passive cooler.) Also, those 2 components are moving parts so will provide some air flow in the case and, even better, PSU fan sucks the air out of the case so it kind of is an exhaust fan in itself. Does anyone run with the exhaust fan disconnected? You don't have to tell me that it's always better to have more air flow than less, I know that, but the noise is also a consideration for me and temperatures around 40C should be fine shouldn't they? (I might also consider getting a quieter case fan but I'm specifically interested in your opinion on the no exhaust fan scenario.)

Read the article
MySQL Config on Large Machine

- by Jonathon

We have a Windows 2003 Enterprise Edition server (64bit) running only MySQL 5.1.45 64-bit. It has 16G RAM and 10T of hard-drive space in RAID 10. We are having horrible performance from mysqld (85-100% CPU utilization). We were running a smaller machine with better performance, so I am assuming our my.ini file is not correct for our current machine. The my.ini file is as follows: [client] port=3306 [mysql] default-character-set=latin1 [mysqld] port=3306 basedir="D:/MySQL/" datadir="D:/MySQL/data" default-character-set=latin1 default-storage-engine=MYISAM sql-mode="" skip-innodb skip-locking max_allowed_packet = 1M max_connections=800 myisam_max_sort_file_size=5G myisam_sort_buffer_size=500M table_open_cache = 512 table_cache=8000 tmp_table_size=30M query_cache_size=50M thread_cache_size=128 key_buffer_size=3072M read_buffer_size=2M read_rnd_buffer_size=16M sort_buffer_size=2M #replication settings (this is the master) log-bin=log server-id = 1 Does anyone see anything wrong with this setup? For a machine with this much RAM, why in the world would mysqld eat up so much CPU? I know we can optimize some queries, etc., but it did run okay on a smaller machine, so I am pretty sure it is the config. Thanks in advance for any help.

Read the article
How to prevent partial crash during VLAN configuration on a HP ProCurve 3500

- by vm370

as you can see from my question, I have a VLAN configuration problem with a ProCurve3500. The goal is to remove a VLAN from the existing configuration, however when I use the WEB UI to do this, I cannot modify ports to be assigned to a different VLAN or the Default VLAN. I always get the message "config failed", which is not very helpful. When I try to do it over telnet, the router somehow partially crashes and somehow the utilization on all ports is at 100% and I can barely use the web ui. After a reboot everything is fine again, but the configuration was not changed... The traffic after this partial crash looks like a broadcast storm, however there are definitely no loops in the segment. I also updated to the latest stable firmware, but the problem persists. Thanks a lot in advance Br vm370

Read the article
Network monitoring solution

- by Hellfrost

Hello Serverfault ! I have a big distributed system I need to monitor. Background: My system is comprised of two servers, concentrating and controlling the system. Each server is connected to a set of devices (some custom kind of RF controllers, doesnt matter to my question), each device connects to a network switch, and eventually all devices talk to the servers, the protocol between the servers and the devices is UDP, usually the packets are very small, but there are really a LOT of packets. the network is also somewhat complex, and is deployed on a large area physically. i'll have 150-300 of these devices, each generating up to 100+ packets per second, and several network switches, perhaps on 2 different subnets. Question I'm looking for some solution that will allow me to monitor all this mess, how many packets are sent, where, how do they move through the network, bandwidth utilization, throughput, stuff like that. what would you recommend to achieve this? BTW Playing nice with windows is a requirement.

Read the article
Graphing services using pnp4nagios

- by Matias

I've managed to install pnp4nagios 0.6.3 and I'm a bit confused about how pnp4nagios generates graphics. Almost out of the box, it started graphs for ping and some http servers (not all of them). But, how can I make it graph things like disk utilization (When that value comes from SNMP)?? For example, ls /usr/local/pnp4nagios/var/perfdata/isis/ Cola_de_Mail.rrd Cola_de_Mail.xml HTTP.rrd HTTP.xml PING.rrd PING.xml Those are checks running on the host isis, but there are many other checks for that server that are not taken into account by pnp4nagios. How can I make pnp4nagios "see" the other checks?? Thanks!

Read the article
Performance degrades for more than 2 threads on Xeon X5355

- by zoolii

Hi All, I am writing an application using boost threads and using boost barriers to synchronize the threads. I have two machines to test the application. Machine 1 is a core2 duo (T8300) cpu machine (windows XP professional - 4GB RAM) where I am getting following performance figures : Number of threads :1 , TPS :21 Number of threads :2 , TPS :35 (66 % improvement) further increase in number of threads decreases the TPS but that is understandable as the machine has only two cores. Machine 2 is a 2 quad core ( Xeon X5355) cpu machine (windows 2003 server with 4GB RAM) and has 8 effective cores. Number of threads :1 , TPS :21 Number of threads :2 , TPS :27 (28 % improvement) Number of threads :4 , TPS :25 Number of threads :8 , TPS :24 As you can see, performance is degrading after 2 threads (though it has 8 cores). If the program has some bottle neck , then for 2 thread also it should have degraded. Any idea? , Explanations ? , Does the OS has some role in performance ? - It seems like the Core2duo (2.4GHz) scales better than Xeon X5355 (2.66GHz) though it has better clock speed. Thank you -Zoolii

Read the article
How important is dual-gigabit lan for a super user's home NAS?

- by Andrew

Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

Read the article
Dialing into multiple PPP connections on Ubuntu

- by sharjeel

I have multiple 3G USB based Modems. I would like them to keep connected simultaneously, NOT necessarily aggregating their bandwidth; a separate intelligent application would manage their utilization effectively. However I am running into problem of setting up proper routes for the ppp0,ppp1 interfaces: when one of them connects, other's entries in the routing table get updated so it is no more usable. If I reconnect the second one, it would override the first one's routing entries. If I do it over and over, sometimes both of them's entries disappear while in rare cases the two work well. I have tried it both using NetworkManager as well as WVDial but issue pops up in both of these. Perhaps both of them use same PPP dialer at the backend and thats why this issue appears. What is the proper solution to make them work together? In the long run, I'd also like them to automatically dial in once USB gets connected.

Read the article
ESXi 5 Guests will not boot

- by Adrian

I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

Read the article
My Computer hangs for a few minutes just after startup, and then is fine.

- by EvilChookie

So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

Read the article
Determine Server specs for a Rails with MySQL database (on AWS)

- by Rogier

I developed a intranet applications with Rails (3.2) for one of my customers. There will be around 30-40 employees working with it. Backend is MySQL (5). What would be the best way to determine the servers specs needed? Given: max. load will be roughly 2400 (40*60) HTTP requests (mixed GET / POST) per hour. 15% of these calls are JSON calls (iOS) avg request will make between 5-10 database calls 500-800 SQL INSERTS per day webpages are fairly simple (no images, just text) avg webpage is 15 request (css/js/etc) and total size is 35-45 KB More specific, since they need access from multiple geographical locations, we are thinking of running a bitnami Ruby stack in the AWS cloud (uptime is important). Any thoughts on a AWS Instance (small/medium) and Utilization (light/medium/heavy) ? Thanks!

Read the article
Very High Network out in ec2 instance

- by Jatin

I launched an ubuntu-14.04-64bit instance in Amazon EC2 two days back. And I started Tomcat 7.0.54 in that instance and deployed my application war files. It has no other software installed other than tomcat and the default ones. In the past 2 days, its shows 858 GB of Data Transfer(Network Out) from that instance. I have attached a graph of Amazon CloudWatch Metric "Network Out" My application does not do any data download/upload. Its a Java Spring application and the front end is in HTML&Javascript. My application traffic was very low (less than 20 hits) in those 2 days. Is there a way to find out why these data transfers happened and also to find what data has been transferred. If you can see in graph, network out was 20gb per minute. Some more info: Network in was negligible CPU Utilization was very high Everything else was low

Read the article
Windows 7 Busy Icon won't stop spinning

- by Lynda

In windows 7 you have the busy icon that is a little blue wheel spinning beside the cursor when it is doing something. It has started to spin for about a second every 3-5 seconds. There is noting running that I can tell on the computer to cause the busy icon. It gets very annoying and I am not sure what to do to get it to stop. Ideas? Running a CPU Usage Gadget says I have less than 5% of the CPU being use and I have over 6GB of RAM free. (I have 8GB total) I am running a 3.6 GHZ AMD FX 4100 processor. EDIT- What I am actually seeing is the working in background pointer (the pointer is still visible beside the busy icon). EDIT 2 - After realizing this happened with the printer installation I turned on the the printer and the busy icon stopped. The printer is setup wirelessly. How do I stop Windows from (I guess) checking for the printer? That is what I assume it is doing. I am using a HP Officejet 8600

Read the article
MySQL is killing the server IO.

- by OneOfOne

I manage a fairly large/busy vBulletin forums (running on gigenet cloud), the database is ~ 10 GB (~9 milion posts, ~60 queries per second), lately MySQL have been grinding the disk like there's no tomorrow according to iotop and slowing the site. The last idea I can think of is using replication, but I'm not sure how much that would help and worried about database sync. I'm out of ideas, any tips on how to improve the situation would be highly appreciated. Specs : Debian Lenny 64bit ~12Ghz (6 cores) CPU, 7520gb RAM, 160gb disk. Kernel : 2.6.32-4-amd64 mysqld Ver 5.1.54-0.dotdeb.0 for debian-linux-gnu on x86_64 ((Debian)) Other software: vBulletin 3.8.4 memcached 1.2.2 PHP 5.3.5-0.dotdeb.0 (fpm-fcgi) (built: Jan 7 2011 00:07:27) lighttpd/1.4.28 (ssl) - a light and fast webserver PHP and vBulletin are configured to use memcached. MySQL Settings : [mysqld] key_buffer = 128M max_allowed_packet = 16M thread_cache_size = 8 myisam-recover = BACKUP max_connections = 1024 query_cache_limit = 2M query_cache_size = 128M expire_logs_days = 10 max_binlog_size = 100M key_buffer_size = 128M join_buffer_size = 8M tmp_table_size = 16M max_heap_table_size = 16M table_cache = 96 Other : > vmstat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 9 0 73140 36336 8968 1859160 0 0 42 15 3 2 6 1 89 5 > /etc/init.d/mysql status Threads: 49 Questions: 252139 Slow queries: 164 Opens: 53573 Flush tables: 1 Open tables: 337 Queries per second avg: 61.302. Edit Additional info.

Read the article
Debian x86_64 + Nginx + PHP5-FPM optimization

- by Olal'a

I used to have a VPS (512MB) from Linode and I was running nginx + php5-fpm (which comes with php5.3.3) on Debian Lenny (i686). The total memory usage was about 90-100MB. Now I have another VPS (different hosting company) and I also run nginx + php5-fpm on Debian Lenny (x86_64). The system is 64-bit, so the memory usage is higher now, about 210-230MB, which I think is too much. Here is my php5-fpm.conf: pm = dynamic pm.max_children = 5 pm.start_servers = 2 pm.min_spare_servers = 2 pm.max_spare_servers = 5 pm.max_requests = 300 That's what top command tells me: top - 15:36:58 up 3 days, 16:05, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 209 total, 1 running, 208 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni, 99.9%id, 0.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 532288k total, 469628k used, 62660k free, 28760k buffers Swap: 1048568k total, 408k used, 1048160k free, 210060k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22806 www-data 20 0 178m 67m 31m S 1 13.1 0:05.02 php5-fpm 8980 mysql 20 0 241m 55m 7384 S 0 10.6 2:42.42 mysqld 22807 www-data 20 0 162m 43m 22m S 0 8.3 0:04.84 php5-fpm 22808 www-data 20 0 160m 41m 23m S 0 8.0 0:04.68 php5-fpm 25102 www-data 20 0 151m 30m 21m S 0 5.9 0:00.80 php5-fpm 10849 root 20 0 44100 8352 1808 S 0 1.6 0:03.16 munin-node 22805 root 20 0 145m 4712 1472 S 0 0.9 0:00.16 php5-fpm 21859 root 20 0 66168 3248 2540 S 1 0.6 0:00.02 sshd 21863 root 20 0 66028 3188 2548 S 0 0.6 0:00.06 sshd 3956 www-data 20 0 31756 3052 928 S 0 0.6 0:06.42 nginx 3954 www-data 20 0 31712 3036 928 S 0 0.6 0:06.74 nginx 3951 www-data 20 0 31712 3008 928 S 0 0.6 0:06.42 nginx 3957 www-data 20 0 31688 2992 928 S 0 0.6 0:06.56 nginx 3950 www-data 20 0 31676 2980 928 S 0 0.6 0:06.72 nginx 3955 www-data 20 0 31552 2896 928 S 0 0.5 0:06.56 nginx 3953 www-data 20 0 31552 2888 928 S 0 0.5 0:06.42 nginx 3952 www-data 20 0 31544 2880 928 S 0 0.5 0:06.60 nginx So, the question is there any way to use less memory? Btw, I have 16 cores and it would be nice to make use of them...

Read the article
How to kill tasks in Windows 7 when even Task Manager won't open or respond?

- by endolith

Occasionally one of my computers will get so bogged down that everything locks up, Ctrl+Alt+Del doesn't work, Task Manager won't open, or they work, but are opening so slowly that it will take hours or days to shut down other processes and regain control of the computer, etc. Is there a way to, for instance, force Task Manager to be highest priority so it always opens immediately with Ctrl+Shift+Esc even when some other process/driver is hogging the CPU? Is there some other program that can run in the background and open immediately like this? This question isn't about fixing "underlying problems". No matter how much memory you have, it's still possible for a rogue process to eat it all up and lock up the computer in page fault thrashing, hog the CPU, etc. This question is about how to take back control of the computer when that happens. Basically when these kind of lock-ups happen, I want to open some kind of task manager that pauses every other process and allows me to kill one of them, and then let everything resume so I can save my work, etc. Otherwise my only option is to hold down the power button. Antifreeze is supposed to do exactly what i want, pausing all other applications and starting a task manager to kill the offender, but in my testing, it actually does neither.

Read the article
"iostat" command different in two equal machines

- by Oz.

We have several machines on Amazon (ec2) of the type c1.xlarge with 8 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are - 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st. Mem is about 1.5GB free. Any idea what could it be, or where else can we check? iostat command on the proper machine: avg-cpu: %user %nice %system %iowait %steal %idle 8.97 0.03 4.46 0.19 0.14 86.23 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.60 0.69 55.38 587620 47254184 xvdfp2 2.64 1.10 61.04 934786 52091056 xvdfp4 0.86 0.19 41.72 163866 35601920 xvdfp1 4.37 36.59 73.89 31220810 63051504 xvdfp3 8.03 7.08 94.63 6045402 80749184 iostat command on problematic machine: avg-cpu: %user %nice %system %iowait %steal %idle 9.29 0.04 5.55 0.26 0.11 84.74 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.13 3.34 68.85 246244 5077888 xvdfp1 7.60 74.31 104.88 5480362 7734840 xvdfp3 13.22 73.67 125.00 5433386 9218600 xvdfp4 1.11 0.76 65.08 55762 4799248 xvdfp2 4.16 3.31 99.17 243818 7313264 Many thanks for the help.

Read the article
Mysterious Windows 7 slowdown problem

- by cletus

I have a fairly beefy machine: Intel Q9450 8GB DDR2800 (4x2) Intel X25-M G2 80GB SSD Several other hard drives Windows 7 Ultimate 64 In the last month I've gotten a mysterious slowdown problem. When I start my IDE (IntelliJ IDEA) it usually takes about 20 seconds on the SSD. If my machine has been on for a day or two (as far as I can tell this is the only pattern) and I try to start the IDE, it brings my machine to a halt. CPU usage goes up to 25% per core (so it's basically 100% usage) and it takes up to 5 minutes to start. Other things I've noticed: iTunes will start to skip and stutter (my music is running off a second hard drive). The only persistent things I'm running are: AVG Anti-Virus Spybot (the slowdown predates this) Hamachi and Murmur (again the slowdown predates this) Apple Airport Base Agent HP OfficeJet 8500 driver/manager The browser I use is Chrome. I can't think why that'd be relevant but it's always on so I thought I'd mention it. When this happens I can't see a reason for it in the process list. No CPU hogs. No spikes in IO activity that I can see. Basically I'm at a loss to explain it and need to reboot, at which point everything returns to normal (for awhile). FWIW the Intel SSD is about 75-80% full. I know being too full can really degrade performance. I don't believe that's the issue here. Does anyone have any ideas on what I can do to fix this or at least help find what's going wrong? This same machine (sans SSD) could run Win XP and stay up fine for a month or two.

Read the article
txt file descriptor in lsof

- by wfaulk

In my experience, files that have the file descriptor of txt in lsof output are the executable file itself and shared objects. The lsof man page says that it means "program text (code and data)". While debugging a problem, I found a large number of data files (specifically, ElasticSearch database index files) that lsof reported as txt. These are definitely not executable files. The process was ElasticSearch itself, which is a java process, if that helps point someone in the right direction. I want to understand how this process is opening and using these files that gets it to be reported in this way. I'm trying to understand some memory utilization, and I suspect that these open files are related to some metrics I'm seeing in some way. The system is Solaris 10 x86.

Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102 | Next Page >