Search Results

Search found 25547 results on 1022 pages for 'table locking'.

Page 976/1022 | < Previous Page | 972 973 974 975 976 977 978 979 980 981 982 983  | Next Page >

• Postmaster uses excessive CPU and Disk Writes

  - by wolfcastle

  using PostgreSQL 9.1.2 I'm seeing excessive CPU usage and large amounts of writes to disk from postmaster tasks. This happens even while my application is doing almost nothing (10s of inserts per MINUTE). There are a reasonable number of connections open however. I've been trying to determine what in my application is causing this. I'm pretty newb with postgresql, and haven't gotten anywhere so far. I've turned on some logging options in my config file, and looked at connections in the pg_stat_activity table, but they are all idle. Yet each connection consumes ~ 50% CPU, and is writing ~15M/s to disk (reading nothing). I'm basically using the stock postgresql.conf with very little tweaks. I'd appreciate any advice or pointers on what I can do to track this down. Here is a sample of what top/iotop is showing me: Cpu(s): 18.9%us, 14.4%sy, 0.0%ni, 53.4%id, 11.8%wa, 0.0%hi, 1.5%si, 0.0%st Mem: 32865916k total, 7263720k used, 25602196k free, 575608k buffers Swap: 16777208k total, 0k used, 16777208k free, 4464212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17057 postgres 20 0 236m 33m 13m R 45.0 0.1 73:48.78 postmaster 17188 postgres 20 0 219m 15m 11m R 42.3 0.0 61:45.57 postmaster 17963 postgres 20 0 219m 16m 11m R 42.3 0.1 27:15.01 postmaster 17084 postgres 20 0 219m 15m 11m S 41.7 0.0 63:13.64 postmaster 17964 postgres 20 0 219m 17m 12m R 41.7 0.1 27:23.28 postmaster 18688 postgres 20 0 219m 15m 11m R 41.3 0.0 63:46.81 postmaster 17088 postgres 20 0 226m 24m 12m R 41.0 0.1 64:39.63 postmaster 24767 postgres 20 0 219m 17m 12m R 41.0 0.1 24:39.24 postmaster 18660 postgres 20 0 219m 14m 9.9m S 40.7 0.0 60:51.52 postmaster 18664 postgres 20 0 218m 15m 11m S 40.7 0.0 61:39.61 postmaster 17962 postgres 20 0 222m 19m 11m S 40.3 0.1 11:48.79 postmaster 18671 postgres 20 0 219m 14m 9m S 39.4 0.0 60:53.21 postmaster 26168 postgres 20 0 219m 15m 10m S 38.4 0.0 59:04.55 postmaster Total DISK READ: 0.00 B/s | Total DISK WRITE: 195.97 M/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 17962 be/4 postgres 0.00 B/s 14.83 M/s 0.00 % 0.25 % postgres: aggw aggw [local] idle 17084 be/4 postgres 0.00 B/s 15.53 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17963 be/4 postgres 0.00 B/s 15.00 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17188 be/4 postgres 0.00 B/s 14.80 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17964 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 18664 be/4 postgres 0.00 B/s 15.13 M/s 0.00 % 0.23 % postgres: aggw aggw [local] idle 17088 be/4 postgres 0.00 B/s 14.71 M/s 0.00 % 0.13 % postgres: aggw aggw [local] idle 18688 be/4 postgres 0.00 B/s 14.72 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 24767 be/4 postgres 0.00 B/s 14.93 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18671 be/4 postgres 0.00 B/s 16.14 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 17057 be/4 postgres 0.00 B/s 13.58 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 26168 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18660 be/4 postgres 0.00 B/s 15.85 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle

  Read the article

• Win XP error 0x80041003 using GetObject/winmgmts

  - by John Lewis

  My computer is called "neil" and I want to set some values using WMI in vbScript. I adapetd the script below from one supplied by Microsoft. When I run it in my browser I get Error Type: (0x80041003) /dressage/30/pdf2.asp, line 8 I suspect it is some registry/security setting. Any advice? John Lewis FULL SCRIPT call Print_HTML_Page("http://neil/dressage/ascii.asp", "ascii") Sub SetPDFFile(strPDFFile) Const HKEY_LOCAL_MACHINE = &H80000002 strKeyPath = "SOFTWARE\Dane Prairie Systems\Win2PDF" strComputer = "." Set objReg=GetObject( _ "winmgmts:{impersonationLevel=impersonate}!\\" & _ strComputer & "\root\default:StdRegProv") strValueName = "PDFFileName" objReg.SetExpandedStringValue HKEY_LOCAL_MACHINE,_ strKeyPath,strValueName,strPDFFile End Sub Sub Print_HTML_Page(strPathToPage, strPDFFile) SetPDFFile( strPDFFile ) Set objIE = CreateObject("InternetExplorer.Application") 'From http://www.tek-tips.com/viewthread.cfm?qid=1092473&page=5 On Error Resume Next strPrintStatus = objIE.QueryStatusWB(6) If Err.Number 0 Then MsgBox "Cannot find a printer. Operation aborted." objIE.Quit Set objIE = Nothing Exit Sub End If With objIE .visible=0 .left=200 .top=200 .height=400 .width=400 .menubar=0 .toolbar=1 .statusBar=0 .navigate strPathToPage End With 'Wait until IE has finished loading Do while objIE.busy WScript.Sleep 100 Loop On Error Goto 0 objIE.ExecWB 6,2 'Wait until IE has finished printing WScript.Sleep 2000 objIE.Quit Set objIE = Nothing End Sub Update: Thanks for your reply. The line breaks seem to have been introduced in the process of paasting into this form. Well spotted - I was using a PDF file name "ascii". I added a .pdf extension but still get the error. I suspect you're right that it's to do with admin rights. Here's more about the setup and what I'm trying to achieve. Win2pdf is a product for writing PDFs by works by simulating a Windows printer. You "print" the page, select win2pdf in the print dialog and it then asks for a file name. I have it installed on my pc (called Neil) and it works fine in this conventional way. My aim is to write an html page to a PDF file using win2pdf - but via ASP/vbscript/javascript rather than with manual intervention. The script for doing this was provided by win2PDF's tech support but when it did not work, that was the limit of their understanding. In the sample script the file ascii.asp just produces a table of ascii codes/characters. The URL given is on my own PC which has IIS set up to run scripts which it does fine. The error I get occurs on about the fourth line executed. I am logged in with full admin rights - I think! But I'm no expert. I hope this helps to give some more specific suggestions about how to check/fix the admin rights.

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Authenticate by libpam-mysql and libnss-mysql (CentOS)

  - by Chris

  I'm trying to get MySQL to function as a backend for authenticating users on CentOS 6.3. So far I have successfully installed and configured libnss-mysql. I can test this by doing: # groups testuser testuser : sftp Testuser is a member of the sftp group in fact, all MySQL based useraccounts will be hardcoded to it. The sftp group is chrooted and forced to use internal-sftp so they cannot do anything but access their home directory. Then I configured pam-mysql and PAM to allow mysql logins. This also works.. When SELinux is not enforcing. When I do setenforce 1 users can no longer login. Error: Permission denied, please try again. This is my pam_mysql.conf file: users.host=localhost users.db_user=nss-pam-user users.db_passwd=*********** users.database=sftpusers users.table=users users.user_column=username users.password_column=password users.password_crypt=6 verbose=1 My /etc/pam.d/sshd: #%PAM-1.0 auth sufficient pam_sepermit.so auth include password-auth auth required pam_mysql.so config_file=/etc/pam_mysql.conf account sufficient pam_nologin.so account include password-auth account required pam_mysql.so config_file=/etc/pam_mysql.conf password include password-auth # pam_selinux.so close should be the first session rule session required pam_selinux.so close session required pam_loginuid.so # pam_selinux.so open should only be followed by sessions to be executed in the user context session required pam_selinux.so open env_params session optional pam_keyinit.so force revoke session include password-auth And to be complete the contents of some log files.. /var/logs/secure Nov 20 14:52:20 hostname unix_chkpwd[4891]: check pass; user unknown Nov 20 14:52:20 hostname unix_chkpwd[4891]: password check failed for user (testuser) Nov 20 14:52:20 hostname sshd[4880]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=192.168.10.107 user=testuser Nov 20 14:52:22 sftpusers sshd[4880]: Failed password for testuser from 192.168.10.107 port 51849 ssh2 /var/logs/audit/audit.log type=USER_AUTH msg=audit(1353420107.070:812): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=pubkey acct="testuser" exe="/usr/sbin/sshd" hostname=? addr=192.168.10.107 terminal=ssh res=failed' type=USER_AUTH msg=audit(1353420112.312:813): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=PAM:authentication acct="testuser" exe="/usr/sbin/sshd" hostname=192.168.10.107 addr=192.168.10.107 terminal=ssh res=failed' type=USER_AUTH msg=audit(1353420112.456:814): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=password acct="testuser" exe="/usr/sbin/sshd" hostname=? addr=192.168.10.107 terminal=ssh res=failed' I tried to let audit2why explain the problem but it remains silent even though there are some errors. Does anyone see the problem? Thanks! EDIT: Turns out it's almost working with setenforce 0 I can mkdir foobar but if I do a single ls I get an error: Received message too long 16777216

  Read the article

• How to unlock and remove a protected partition from Prestigio USB stick?

  - by mr.b

  Ok, so, I have one of those fancy schmancy devices, which is given to me by a frustrated friend of mine. Device is a Prestigio Leather 8GB, which identifies itself to Linux host as: Bus 001 Device 006: ID 1307:0165 Transcend Information, Inc. 2GB/4GB Flash Drive Kernel messages as USB device is plugged in: kernel: [ 2769.580042] usb 1-9: new high speed USB device using ehci_hcd and address 7 kernel: [ 2769.714782] scsi8 : usb-storage 1-9:1.0 kernel: [ 2770.713937] scsi 8:0:0:0: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.714535] scsi 8:0:0:1: Direct-Access 8192MB flash drive 1.00 PQ: 0 ANSI: 2 kernel: [ 2770.715734] sd 8:0:0:0: Attached scsi generic sg3 type 0 kernel: [ 2770.716108] sd 8:0:0:1: Attached scsi generic sg4 type 0 kernel: [ 2770.722175] sd 8:0:0:0: [sdc] 962560 512-byte logical blocks: (492 MB/470 MiB) kernel: [ 2770.722657] sd 8:0:0:0: [sdc] Write Protect is on kernel: [ 2770.731078] sd 8:0:0:1: [sdd] 14012416 512-byte logical blocks: (7.17 GB/6.68 GiB) kernel: [ 2770.731215] sdc: kernel: [ 2770.738251] sd 8:0:0:1: [sdd] Write Protect is off kernel: [ 2770.880328] kernel: [ 2770.885876] sd 8:0:0:0: [sdc] Attached SCSI removable disk kernel: [ 2770.887442] sdd: unknown partition table kernel: [ 2771.049605] sd 8:0:0:1: [sdd] Attached SCSI removable disk So, symptoms are typical for U3-like devices: two separate devices inside of a single flash device. Windows sees it also as two identical usb devices, and mounts two separate drives to system, whereas first one presents itself as a CDROM device, holding a write-protected content, and second is a regular flash-disk partition, that "can" be written to. However, it seems like it's broken in some weird way, since it won't let me write anything to it, format it, nothing, but that's not the issue right now. Question: How can I unlock entire USB stick so it appears to system as a single, 8GB device which can be partitioned and used normally, without restrictions? Since it appeared to be an U3 device, I have tried standard utilities: both U3 Uninstaller by u3.com (found on SoftPedia), and opensource u3_tool from sourceforge (on both Windows and Linux). First utility failed to even detect USB stick as U3 device (simply stood idle while I re-plugged stick several times), while second tool failed with some obscure error about SCSI command unable to do something (I might be able to provide exact errors when I switch back to windows). u3_tool -i /dev/sg3 (Display device info) fails with u3_partition_info() failed: Device reported command failed: status 1 ...and every other option fails with same error, minus first part which states which command precisely has failed. So, apparently, this isn't a U3 device. Or, if it is, it doesn't behave like one. I read on a few occasions that this device protection is done by special command sent to device which tells it to lock itself, and so there should be an unlock command, that would set drive straight. Does anyone have any idea about what could I do to this device to fix it? P.S. I also mentioned a problem with being unable to use second "drive", but I'll tackle that problem when (and if) I manage to merge those two devices into one...

  Read the article

• Macintosh computers cannot connect to router unless we re-start the modem and router

  - by dwwilson66

  We have a small office network with DSL and a Netgear WNR-2000 wireless router acting as a DHCP server. There are nine devices connected to the router, wirelessly and wired. Whenever a Mac computer tries to connect, it's unsuccessful until we restart the router. Each of the possible devices that can connect to the network is listed in a table to assign certain IP addresses to certain MAC addresses. I am running WPA-PSK security. I can view the router status and see that the Mac's MAC address is visible to the router, but with a 169.* IP address, even though I'm assigning its MAC address to an IP address within my subnet. All non-Mac devices attached to the network connect properly, and can access the network properly even AFTER the Mac has not successfully connected. The network includes Windows devices, Roku boxes, printers and internet ready TVs. This to me, would point to a DHCP issue with how Mac communicates with my network. One interesting thing to note is that if a Mac connects and is prevented from sleeping, it will stay connected indefinitely; reissuing the security cert from the router works fine. I'm not sure if that's supposed to sever & re-establish a connection with the updated credentials or not, but I do stay connected. If the Mac sleeps and is awakened while the security cert is still valid, it connects fine. If the security certificate expires while the Mac is asleep, we need to restart the router. Restarting the router will ALWAYS assigns the proper IP addresses to the Mac equipment. I have heard anecdotally that Mac doesn't play well with 802.11n; I have not tested any other Wireless protocols. There's a couple issues here: First, I found this on Stack, Mac laptop crashing wireless router, but it's not rally applicable since the router isn't crashing. But, it does give some clues about Mac's accessing the network. I did change my encryption from WEP to WPA-PSK, but after about a week, we're still experiencing the issue. I'm not really sure if there's anything else useful in that question. Second, I'm considering getting a 802.11c router and hooking it up to the wireless N router. the 802.11c router would handle all the Mac traffic, and would be set up as a Mac-only subnet. Everything else would remain as is. However, I'm not sure if this is doable on a technology level...do I need a bridge or is this some way to do this with regular consumer gear?

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• External USB HD issues with a twist (works on Windows7 but not XP)

  - by Eruditass

  I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

  Read the article

• Windows Setup could not configure Windows to run on this computer's hardware

  - by Hello71

  The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

  Read the article

• Why MySQL sat for 2 minutes doing nothing?

  - by Alex R

  This was a one-time thing, not reproducible... But I saved the show innodb status output. Can anybody tell what's going on here? The simple insert took almost 3 minutes to complete. | InnoDB | | ===================================== 110201 15:58:10 INNODB MONITOR OUTPUT ===================================== Per second averages calculated from the last 34 seconds ---------- SEMAPHORES ---------- OS WAIT ARRAY INFO: reservation count 11963, signal count 11766 --Thread 1824 has waited at .\btr\btr0cur.c line 443 for 118.00 seconds the sema phore: S-lock on RW-latch at 09D6453C created in file .\buf\buf0buf.c line 550 a writer (thread id 1824) has reserved it in mode wait exclusive number of readers 1, waiters flag 1 Last time read locked in file .\buf\buf0flu.c line 599 Last time write locked in file .\btr\btr0cur.c line 443 Mutex spin waits 0, rounds 527817, OS waits 7133 RW-shared spins 2532, OS waits 1226; RW-excl spins 1652, OS waits 1118 ------------ TRANSACTIONS ------------ Trx id counter 0 95830 Purge done for trx's n:o < 0 95814 undo n:o < 0 0 History list length 11 LIST OF TRANSACTIONS FOR EACH SESSION: ---TRANSACTION 0 0, not started, OS thread id 3704 MySQL thread id 551, query id 2702112 localhost 127.0.0.1 root show innodb status ---TRANSACTION 0 95829, not started, OS thread id 3132 MySQL thread id 534, query id 2702020 localhost 127.0.0.1 root ---TRANSACTION 0 95828, not started, OS thread id 3152 MySQL thread id 527, query id 2701973 localhost 127.0.0.1 root ---TRANSACTION 0 95827, ACTIVE 118 sec, OS thread id 1824 inserting, thread decl ared inside InnoDB 500 mysql tables in use 1, locked 1 1 lock struct(s), heap size 320, 0 row lock(s) MySQL thread id 526, query id 2701972 localhost 127.0.0.1 root update INSERT INTO log_searchcriteria (userid,search_criteria,date,search_type) VALUES ( NAME_CONST('userid',NULL), NAME_CONST('search_criteria',_latin1' SELECT SQL_C ALC_FOUND_ROWS idx_search.CTCX_LATITUDE, idx_search.CTCX_LONGITUDE, idx_search.b uilding_id, idx_search.LN_LIST_NUMBER, idx_search.LP_LIST_PRICE, idx_search.HSN_ ADRESS_HOUSE_NUMBER, idx_search.STR_ADDRESS_STREET, idx_search.CP_ADDRESS_COMPAS S_POINT, idx_search.UN_UNIT, idx_search.CIT_CITY, idx_search.ZP_ZIP_CODE, idx_se arch.AR_AREA_NAME, idx_search.BR_BEDROOMS, idx_search.BTH_BATHS, idx_search.ST_S TATUS, idx_search.CTCX_STYLE_TYPE, idx_s -------- FILE I/O -------- I/O thread 0 state: wait Windows aio (insert buffer thread) I/O thread 1 state: wait Windows aio (log thread) I/O thread 2 state: wait Windows aio (read thread) I/O thread 3 state: wait Windows aio (write thread) Pending normal aio reads: 0, aio writes: 1, ibuf aio reads: 0, log i/o's: 0, sync i/o's: 0 Pending flushes (fsync) log: 0; buffer pool: 0 151006 OS file reads, 120758 OS file writes, 6844 OS fsyncs 0.00 reads/s, 0 avg bytes/read, 0.00 writes/s, 0.00 fsyncs/s ------------------------------------- INSERT BUFFER AND ADAPTIVE HASH INDEX ------------------------------------- Ibuf: size 1, free list len 5, seg size 7, 24664 inserts, 24664 merged recs, 4612 merges Hash table size 553253, node heap has 629 buffer(s) 0.00 hash searches/s, 0.00 non-hash searches/s --- LOG --- Log sequence number 5 2318193115 Log flushed up to 5 2318193115 Last checkpoint at 5 2318129891 0 pending log writes, 0 pending chkp writes 3036 log i/o's done, 0.00 log i/o's/second ---------------------- BUFFER POOL AND MEMORY ---------------------- Total memory allocated 213459462; in additional pool allocated 1720192 Dictionary memory allocated 240416 Buffer pool size 8192 Free buffers 0 Database pages 7563 Modified db pages 18 Pending reads 0 Pending writes: LRU 0, flush list 18, single page 0 Pages read 150973, created 28788, written 115137 0.00 reads/s, 0.00 creates/s, 0.00 writes/s No buffer pool page gets since the last printout -------------- ROW OPERATIONS -------------- 1 queries inside InnoDB, 0 queries in queue 1 read views open inside InnoDB Main thread id 2992, state: flushing buffer pool pages Number of rows inserted 794294, updated 89203, deleted 13698, read 1453084305 0.00 inserts/s, 0.00 updates/s, 0.00 deletes/s, 0.00 reads/s ---------------------------- END OF INNODB MONITOR OUTPUT ============================ Thanks

  Read the article

• Windows 2008 running as KVM guest networking issue

  - by Evolver

  I have a strange networking problem with Windows 2008 server R2, running as guest under KVM-Qemu host. Host is CentOS 6.3 x86_64. It's network settings: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE=br0 BOOTPROTO=static BROADCAST=xx.xx.xx.63 IPADDR=xx.xx.xx.4 NETMASK=255.255.255.192 NETWORK=xx.xx.xx.0 ONBOOT=yes TYPE=Bridge # cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=xx:xx:xx:xx:xx:xx ONBOOT=yes BRIDGE=br0 IPV6INIT=yes IPV6_AUTOCONF=yes # cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=my.hostname GATEWAY=xx.xx.xx.1 # cat /etc/sysctl net.ipv4.ip_forward = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.rp_filter = 1 # tried to set it to 0 without any changes net.ipv4.conf.default.accept_source_route = 0 # tried to set it to 1 without any changes kernel.sysrq = 0 kernel.core_uses_pid = 1 net.ipv4.tcp_syncookies = 1 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 kernel.msgmnb = 65536 kernel.msgmax = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 1004 0 0 br0 0.0.0.0 xx.xx.xx.1 0.0.0.0 UG 0 0 0 br0 Node IP is xx.xx.xx.4, guest IP is xx.xx.xx.24, both host and guest is in the same network (/26). There are several linux guest running fine on the node (centos, debian, ubuntu, arch), and even Windows 2003 x86 also running fine. But Win2008 does not. I wonder, what's the difference. From Win2008 guest I can ping nothing: neither gateway, nor any other IP, even they are in the same subnet. From outside I also cannot ping guest. Almost. If I ping it from another server in same subnet, it's barely pinging, losing more than 90% packets. Firewall on the guest is completely off. Tried to set up network manually as well as via DHCP without success (BTW, DHCP set up network settings correctly). I suspect that is a kind of routing problem, but I spent whole day and still cannot figure it out. I would be appreciate for any help.

  Read the article

• Do RAID controllers commonly have SATA drive brand compatibility issues?

  - by Jeff Atwood

  We've struggled with the RAID controller in our database server, a Lenovo ThinkServer RD120. It is a rebranded Adaptec that Lenovo / IBM dubs the ServeRAID 8k. We have patched this ServeRAID 8k up to the very latest and greatest: RAID bios version RAID backplane bios version Windows Server 2008 driver This RAID controller has had multiple critical BIOS updates even in the short 4 month time we've owned it, and the change history is just.. well, scary. We've tried both write-back and write-through strategies on the logical RAID drives. We still get intermittent I/O errors under heavy disk activity. They are not common, but serious when they happen, as they cause SQL Server 2008 I/O timeouts and sometimes failure of SQL connection pools. We were at the end of our rope troubleshooting this problem. Short of hardcore stuff like replacing the entire server, or replacing the RAID hardware, we were getting desperate. When I first got the server, I had a problem where drive bay #6 wasn't recognized. Switching out hard drives to a different brand, strangely, fixed this -- and updating the RAID BIOS (for the first of many times) fixed it permanently, so I was able to use the original "incompatible" drive in bay 6. On a hunch, I began to assume that the Western Digital SATA hard drives I chose were somehow incompatible with the ServeRAID 8k controller. Buying 6 new hard drives was one of the cheaper options on the table, so I went for 6 Hitachi (aka IBM, aka Lenovo) hard drives under the theory that an IBM/Lenovo RAID controller is more likely to work with the drives it's typically sold with. Looks like that hunch paid off -- we've been through three of our heaviest load days (mon,tue,wed) without a single I/O error of any kind. Prior to this we regularly had at least one I/O "event" in this time frame. It sure looks like switching brands of hard drive has fixed our intermittent RAID I/O problems! While I understand that IBM/Lenovo probably tests their RAID controller exclusively with their own brand of hard drives, I'm disturbed that a RAID controller would have such subtle I/O problems with particular brands of hard drives. So my question is, is this sort of SATA drive incompatibility common with RAID controllers? Are there some brands of drives that work better than others, or are "validated" against particular RAID controller? I had sort of assumed that all commodity SATA hard drives were alike and would work reasonably well in any given RAID controller (of sufficient quality).

  Read the article

• Network use of Gaming PC

  - by Matthew Patrick Cashatt

  Background After YEARS of waiting, I built the custom gaming PC of my dreams: Intel i7 - 975 Extreme Edition 3.3ghz (overclocked to 4.0) ATI Radeon 5970 2gb Corsair 256 gb SSD Drive 2 TB Sata II 3.0 7200rpm data drive 12 GB Kingston Hyper-X (1600mhz) DDR3 Windows 7 Ultra 64 bit And so on. . . Problem I hooked this beast up to our home theater and settled in for a great gaming season only to realize a couple of drawbacks: It's hard to accurately wax bad guys using a keyboard in your lap whilst reclined on your couch (and using a wireless keyboard). It's hard to read the text on the screen (i.e. menus, etc). I find that a 1:1 ratio (screen diagonal inch to inch away from screen) is optimum, but using the home theater, it's more like 1:3 which has me squinting unless I sit on the coffee table. The wife always seems to want the TV the same time I do and, unfortunately "Real Housewives of Beverly Hills" and Battlefield BC don't mix. I am losing the battle in the home theater room, but the PC has to stay there (long story). So, this leaves me with the option of playing in my home office which is about 30 feet away from the home theater. I am a software developer so I have a pretty decent set up in my office--multiple 1080p monitors, HP Envy 17 which can run games like Crysis in 720p with out stammering too much. Also, I can game very comfortably at my desk in the office. Still, even though the set up in my office can run games well enough, I don't want to regress to that when I have worked YEARS for an awesome gaming PC that can run everything on ultra high settings. My Question What are my options for running my games on the beastly desktop in the Home Theater, but physically playing in my office about 30 feet away? A really long HDMI cable? LAN/RDC? Details that May Help We have an open crawlspace so running cable from HT room to office is no problem. I already have networked the house with a LAN Any help is GREATLY appreciated. Thanks, Matt

  Read the article

• Pinning based on origin of a reprepro repository.

  - by Shtééf

  I'm on Ubuntu 10.04, and trying to set up a repository using reprepro. I'd also like the pin everything in that repository to be preferred over anything else, even if packages are older versions. (It will only contain a select set of packages.) However, I cannot seem to get the pinning to work, and believe it has something to do with the repository side of things, rather than the apt configuration on the client. I've taken the following steps to set up my repository Installed a web server (my personal choice here is Cherokee), Created the directory /var/www/apt/, Created the file conf/distributions, like so: Origin: Shteef Label: Shteef Suite: lucid Version: 10.04 Codename: lucid Architectures: i386 amd64 source Components: main Description: My personal repository Ran reprepro export from the /var/www/apt/ directory. Now on any other machine, I can add this (empty) repository over HTTP to my /etc/apt/sources.list, and run apt-get update without any errors: Ign http://archive.lan lucid Release.gpg Ign http://archive.lan/apt/ lucid/main Translation-en_US Get:1 http://archive.lan lucid Release [2,244B] Ign http://archive.lan lucid/main Packages Ign http://archive.lan lucid/main Sources Ign http://archive.lan lucid/main Packages Ign http://archive.lan lucid/main Sources Hit http://archive.lan lucid/main Packages Hit http://archive.lan lucid/main Sources In my case, now I want to use an old version of Asterisk, namely Asterisk 1.4. I rebuilt the asterisk-1:1.4.21.2~dfsg-3ubuntu2.1 package from Ubuntu 9.04 (with some small changes to fix dependencies) and uploaded it to my repository. At this point I can see the new package in aptitude, but it naturally prefers the newer Asterisk 1.6 currently in the Ubuntu 10.04 repositories. To try and fix that, I have created /etc/apt/preferences.d/personal like so: Package: * Pin: release o=Shteef Pin-Priority: 1000 But when I try to install the asterisk package, it will still prefer the 1.6 version over my own 1.4 version. This is what apt-cache policy asterisk shows: asterisk: Installed: (none) Candidate: 1:1.6.2.5-0ubuntu1 Version table: 1:1.6.2.5-0ubuntu1 0 500 http://nl.archive.ubuntu.com/ubuntu/ lucid/universe Packages 1:1.4.21.2~dfsg-3ubuntu2.1shteef1 0 500 http://archive.lan/apt/ lucid/main Packages Clearly, it is not picking up my pin. In fact, when I run just apt-cache policy, I get the following: Package files: 100 /var/lib/dpkg/status release a=now 500 http://archive.lan/apt/ lucid/main Packages origin archive.lan 500 http://security.ubuntu.com/ubuntu/ lucid-security/multiverse Packages release v=10.04,o=Ubuntu,a=lucid-security,n=lucid,l=Ubuntu,c=multiverse origin security.ubuntu.com [...] Unlike Ubuntu's repository, apt doesn't seem to pick up a release-line at all for my own repository. I'm suspecting this is the cause why I can't pin on release o=Shteef in my preferences file. But I can't find any noticable difference between my repository's Release files and Ubuntu's that would cause this. Is there a step I've missed or mistake I've made in setting up my repository?

  Read the article

• init never reaping zombie/defunct processes

  - by st9

  Hi, On my Fedora Core 9 webserver with kernel 2.6.18.8, init isn't reaping zombie processes. This would be bearable if it wasn't for the process table eventually reaching an upper limit where no new processes can be allocated. Sample output of ps -el | grep 'Z': F S UID PID PPID C PRI NI ADDR SZ WCHAN TTY TIME CMD 5 Z 0 2648 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 1 Z 51 2656 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 1 Z 0 2670 1 0 75 0 - 0 exit ? 00:00:02 crond <defunct> 4 Z 0 2874 1 0 82 0 - 0 exit ? 00:00:00 mysqld_safe <defunct> 5 Z 0 28104 1 0 76 0 - 0 exit ? 00:00:00 httpd <defunct> 5 Z 0 28716 1 0 76 0 - 0 exit ? 00:00:06 lfd <defunct> 5 Z 74 10172 1 0 75 0 - 0 exit ? 00:00:00 sshd <defunct> 5 Z 0 11199 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11202 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11205 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11208 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11211 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11240 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11246 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11249 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 5 Z 0 11252 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> 1 Z 0 14106 1 0 80 0 - 0 exit ? 00:00:00 anacron <defunct> 5 Z 0 14631 1 0 75 0 - 0 exit ? 00:00:00 sendmail <defunct> Is this an OS bug? misconfiguration? I'm looking for inspiration as to the source of this problem. Thanks

  Read the article

• configuration required for HIVE to be installed on a node

  - by ????? ????????

  I went through the process of manually installing ambari (not through SSH, because I couldnt get keyless to work) and everything installed OK, except for HIVE and GANGLIA. I got this message: stderr: None stdout: warning: Unrecognised escape sequence ‘\;’ in file /var/lib/ambari-agent/puppet/modules/hdp-hive/manifests/hive/service_check.pp at line 32 warning: Dynamic lookup of $configuration is deprecated. Support will be removed in Puppet 2.8. Use a fully-qualified variable name (e.g., $classname::variable) or parameterized classes. notice: /Stage[1]/Hdp::Snappy::Package/Hdp::Snappy::Package::Ln[32]/Hdp::Exec[hdp::snappy::package::ln 32]/Exec[hdp::snappy::package::ln 32]/returns: executed successfully notice: /Stage[2]/Hdp-hive::Hive::Service_check/File[/tmp/hiveserver2Smoke.sh]/ensure: defined content as ‘{md5}7f1d24221266a2330ec55ba620c015a9' notice: /Stage[2]/Hdp-hive::Hive::Service_check/File[/tmp/hiveserver2.sql]/ensure: defined content as ‘{md5}0c429dc9ae0867b5af74ef85b5530d84' notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/File[/tmp/hcatSmoke.sh]/ensure: defined content as ‘{md5}bae7742f7083db968cb6b2bd208874cb’ notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:11:56 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException org.apache.hadoop.hive.ql.parse.SemanticException: org.apache.hadoop.hive.ql.metadata.HiveException: java.lang.RuntimeException: Unable to instantiate org.apache.hadoop.hive.metastore.HiveMetaStoreClient notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:12:06 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException [Error 10001]: Table not found hcatsmokeida8c07401_date102513 notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: 13/06/25 03:12:15 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. Make sure to provide a valid value for hive.metastore.uris if you are connecting to a remote metastore. notice: /Stage[2]/Hdp-hcat::Hcat::Service_check/Exec[hcatSmoke.sh prepare]/returns: FAILED: SemanticException o When i go to the alerts and health checks i’m getting this: ive Metastore status check CRIT for 42 minutes CRITICAL: Error accessing hive-metaserver status [13/06/25 03:44:06 WARN conf.HiveConf: DEPRECATED: Configuration property hive.metastore.local no longer has any effect. What am I doing wrong? I have already tried to do ambari-server reset on the the database without results.

  Read the article

• Asus M4A79XTD-EVO / AMD Phenom II X4 965 Crashes / BSOD / Hangs / Restarts

  - by Tiby

  I'll try to be as concise as possible because I have a lot to say about my problem, but I'd rather say it when asked or when I feel it's necessary, just to make this initial reading clearer. For about a year and a half I have periods when my system has all the problems in the title (I'll use the word 'crash' for either one). I'll list some patterns and what I tried to do and what were the results, but the list is not exclusive: usually it crashes when a CPU-intensive operation is in progress, like a game or video encoding or HD movie rendering, but also sometimes crashes when I'm doing nothing after a first crash the system is very unstable and sometimes it crashes even during POST, or doesn't boot at all Some months ago I went to a local service (one that you just put your computer on the table and sit there with a guy and trying to figure out the problem, very rare these days) and they used OCCT and it crashed every time he changed some part to test it out (PSU, RAM, video card, HDD). The last one was the CPU. They changed the CPU and it didn't crash any more. Then when they put my CPU back, it also didn't crash. We figured that the trouble was the thermal paste (probably some 2 years old) because it was the only thing changed while testing. Up until 2 weeks ago, I haven't had any more problems. 2 weeks ago the problems reappeared. I changed again the thermal paste, put some Arctic Silver 5, and for about a week everything worked perfect (tried some games, video encoding, no more crashes). But again it started crashing in the same fashion as the first time. But now, instead, I figured out a very odd behaviour: when I start some of the apps above, in most cases it crashes if I start OCCT and turn on the CPU test, and run any of the programs above, it doesn't crash, even if the CPU is on 100% load (and 65-70 degrees Celsius temperature) if I shut down OCCT and continue using the programs, it crashes in a very short period of time (even if the CPU is on 5-10% load and 40 degrees) There are so many patterns and temporary solutions that I figured out in this year and a half period of time, that I can't include them all because I don't know which one are more relevant, but I'll happily provide any details you ask. My system is: CPU: AMD Phenom II X4 965 (3400 MHz - 125W) MB: ASUS M4A79XTD - EVO RAM: Corsair Vengeance 8 GB (2 x 4GB) CL8 1600MHz Video: HIS Radeon HD5770 1GB PSU: Corsair 750W HDD: Western Digital 1TB OS: Win 7 Enterprise 64 BIT (also tried with Windows Server 2008 R2 Trial and Win XP)

  Read the article

• SMB returns the entire file instead of header info

  - by billdlawson

  Starting a section of code checks for access to many data files (flat files so each table is a file) and when I do a packet capture, in our capture only the header info is sent by the server to the client. However I have one Customer who is using a SAN that gets the whole file instead of just the header info,and besides just being slower, this is causing file access issues. They have already turned off OPLOCKS at the server and at the workstations. This is not client server. The data files and the application reside on the server but the users run the application locally via a shortcut with a mapped drive or UNC. So when I simply select an option that prompts for a vehicle number, not tryng to select a record but rather simply verify the datafiles are accessible, that window opens in 1-2 seconds for me. When they do the same thing it takes 6-15 seconds after there several users are running the program. Maximum number of users is 15. The program has a lot of small modules, 800 .cob modules. So it is very chatty but these are datafiles. We have Wireshark captures that show he's pulling the whole file and we're just getting the header. Thier capture vs ours. We suspect the SAN. Has anyone ever heard of a SAN improperly interpreting runtime requests? So an SMB request. This is Acucobol-GT (now Microfocus). The application is written in COBOL. This is not a new program just a new problem. This is one customer of over a thousand who are otherwise running smoothly and we are totally stumped. All XP users, the server is Windows 2003 (with Virtual server) and I don't yet know the SAN info. Also we have many installations running virtual servers but only few on SANs or we just don't know it. This is not a network throught put issue, the load is less than 5% on the server and theer are no timeout or retransmits. PS If it wasn't for Wireshark I'd still be chasing my tail. An application trace file on thier installation just looks like they run slower. If you want the Wireshark trace file I can make it available. Thanks in advance - Please excuse my verbosity (word?) but I'm not sure what's relavent.

  Read the article

• Raid1 with active and spare partition

  - by Daniel Baron

  I am having the following problem with a RAID1 software raid partition on my Ubuntu system (10.04 LTS, 2.6.32-24-server in case it matters). One of my disks (sdb5) reported I/O errors and was therefore marked faulty in the array. The array was then degraded with one active device. Hence, I replaced the harddisk, cloned the partition table and added all new partitions to my raid arrays. After syncing all partitions ended up fine, having 2 active devices - except one of them. The partition which reported the faulty disk before, however, did not include the new partition as an active device but as a spare disk: md3 : active raid1 sdb5[2] sda5[1] 4881344 blocks [2/1] [_U] A detailed look reveals: root@server:~# mdadm --detail /dev/md3 [...] Number Major Minor RaidDevice State 2 8 21 0 spare rebuilding /dev/sdb5 1 8 5 1 active sync /dev/sda5 So here is the question: How do I tell my raid to turn the spare disk into an active one? And why has it been added as a spare device? Recreating or reassembling the array is not an option, because it is my root partition. And I can not find any hints to that subject in the Software Raid HOWTO. Any help would be appreciated. Current Solution I found a solution to my problem, but I am not sure that this is the actual way to do it. Having a closer look at my raid I found that sdb5 was always listed as a spare device: mdadm --examine /dev/sdb5 [...] Number Major Minor RaidDevice State this 2 8 21 2 spare /dev/sdb5 0 0 0 0 0 removed 1 1 8 5 1 active sync /dev/sda5 2 2 8 21 2 spare /dev/sdb5 so readding the device sdb5 to the array md3 always ended up in adding the device as a spare. Finally I just recreated the array mdadm --create /dev/md3 --level=1 -n2 -x0 /dev/sda5 /dev/sdb5 which worked. But the question remains open for me: Is there a better way to manipulate the summaries in the superblock and to tell the array to turn sdb5 from a spare disk to an active disk? I am still curious for an answer.

  Read the article

• Basic OpenVPN setup not working

  - by WalterJ89

  I am attempting to connect 2 win7 (x64+ x32) computers (there will be 4 in total) using OpenVPN. Right now they are on the same network but the intention is to be able to access the client remotely regardless of its location. The Problem I am having is I am unable to ping or tracert between the two computers. They seem to be on different subnets even though I have the mask set to 255.255.255.0. The server ends up as 10.8.0.1 255.255.255.252 and the client 10.8.0.6 255.255.255.252. And a third ends up as 10.8.0.10. I don't know if this a Windows 7 problem or something I have wrong in my config. Its a very simple set up, I'm not connecting two LANs. this is the server config (removed all the extra lines because it was too ugly) port 1194 proto udp dev tun ca keys/ca.crt cert keys/server.crt key keys/server.key # This file should be kept secret dh keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt client-to-client duplicate-cn keepalive 10 120 comp-lzo persist-key persist-tun status openvpn-status.log verb 6 this is the client config client dev tun proto udp remote thisdomainis.random.com 1194 resolv-retry infinite nobind persist-key persist-tun ca keys/ca.crt cert keys/client.crt key keys/client.key ns-cert-type server comp-lzo verb 6 Is there anything I missed in this? keys are all correct and the vpn's connect fine, its just the subnet or route issue. Thank You EDIT it seems on the server the openvpn-status.log has the routes for the client SERVER OpenVPN CLIENT LIST Updated,Wed May 19 18:26:32 2010 Common Name,Real Address,Bytes Received,Bytes Sent,Connected Since client,192.168.10.102:50517,19157,20208,Wed May 19 17:38:25 2010 ROUTING TABLE Virtual Address,Common Name,Real Address,Last Ref 10.8.0.6,client,192.168.10.102:50517,Wed May 19 17:38:56 2010 GLOBAL STATS Max bcast/mcast queue length,0 END Also this is from the client.log file: Which seems to be correct C:\WINDOWS\system32\route.exe ADD 10.8.0.0 MASK 255.255.255.0 10.8.0.5 Another EDIT 'route print' on the server shows the route: Destination Mask Gateway Interface 10.8.0.0 255.255.255.0 10.8.0.2 10.8.0.1 the same on the client shows 10.8.0.0 255.255.255.0 10.8.0.5 10.8.0.6 So the routes are there.. what can the problem be? Is there anything wrong with my configs? Why would OpenVPN be having problems communicating?

  Read the article

• Unable to delete all partitions on flash drive using Windows 7 OS??

  - by irrational John

  Recently I purchased an ADATA C802 8GB flash drive. Since the drive was new I decided to run some of the HD Tune Pro (v4.50) performance tests on it, mostly just for the heck of it. To avoid accidently destroying data HD Tune refuses to write to a drive unless there are no partitions on the drive. If you do attempt to write to a drive with partitions, it posts the message "Writing is disabled. To enable writing please remove all partitions." As you would expect, the ADATA came formatted with a single primary FAT32 partition in the Master Boot Record. But a number of unexpected things happened when I attempted to delete that partition. The first thing I tried was to use the Windows 7 (64-bit) Disk Management tool (diskmgmt.msc) to delete the partition. It would not let me. The context menu choice to delete that volume was not available. Next I opened up a command prompt window with Admin authority and ran diskpart. Diskpart deleted the volume for me. However, when I attempted to run an HD Tune write test on the drive I still got the "Writing is disabled" message. Huh??? So I fired up a utility I have which allows viewing drives at the sector level and verified that the partition table in the Master Boot Record was empty. No partitions. Yet HD Tune still thought there were partitions on the drive? So why was I still getting the "Writing is disabled" message from HD Tune Pro? And why wouldn't the Windows 7 Disk Management tool let me change the partitions on this drive. After doing the above, I plugged the ADATA into my MacBook. I was then able to format it as either a GPT or MBR partitioned drive with no problems. I am not looking for suggestions on how to format this drive. I can do that. What I do not understand and was hoping I might get insight into is why this drive behaves so strangely under Windows 7? And BTW, what's up with HD Tune Pro? BTW, if I plug the drive I formatted on my MacBook back into my Windows 7 64-bit system I still run into road blocks with the Disk Management tool. For example, I cannot delete all the GPT partitions on the ADATA so I can convert it into an MBR drive. I following Microsoft's instructions, the instructions just do not work with this ADATA flash drive. Anyone know what's up with this? It makes no sense to me. Has something changed in Windows 7 (Vista)??

  Read the article

• Seeking (somewhat) better explanations about supporting > 2.1 TB hard drives.

  - by irrational John

  Today while Googling about I stumbled across posts claiming that Seagate plans to ship a 3TB drive sometime later in 2010. Unfortunately, the stuff I looked at all seemed to contain tidbits of info which I didn't think fit together properly. (I would link to some examples, but I'm only allowed 1 link per post at the moment). Now I really don't have any "need" to better understand the underlying tedious details of this. I am just curious. And confused. So ... some questions I'm hoping someone better informed than I might answer. The talk about a potential addressing problem in both the hardware and the software confused me. The assertion is that something called something called Long LBA addressing (LLBA) is needed in the Command Descriptor Block as a way to get around the current limits to access a hard drive bigger than ~2.1 (or ~2.2?) TB. OK, fine. But I thought the last time this problem came up it was solved by extending the length of the LBA field from 28 to 48 bits. (Remember this website? www.48bitlba.com) A 6 byte LBA is clearly large enough, so what's up with this LLBA talk. I thought this was all fixed back by Win XP SP2, if not sooner? And certainly all the hardware should be up to the task, shouldn't it? The real problem as I understand it with drives much bigger than 2 TB are the 4 byte LBA fields in the Master Boot Record (MBR) used to partition just about all hard drives at the moment. The most likely solution is to migrate to Intel's GUID Partition Table (GPT). A GPT uses 8 byte fields for the LBA. What I don't understand in this context is what is the problem with booting say Windows from a 3TB drive that uses a GPT. Granted, the current PC BIOS wouldn't know how to recognize or work with a GPT. But every GPT comes with a so-called "Safety" or "Guarding" MBR in sector 0.Apple already uses a hybrid version of the MBR to allow them to boot Windows on their Intel Macs (aka Boot Camp). Couldn't something similar be done to allow the PC BIOS to recognize and boot from a partition in, say, the first 1 GB of a 3GB or larger drive? I've got more questions such as where do 4K sectors fit into all of this. But it's probably time I just shut up and posted this. ;-) -irrational john

  Read the article

• What Are All the Variables Necessary to Create Blackbox Logs for Nginx?

  - by Alan Gutierrez

  There's an article out there, Profiling LAMP Applications with Apache's Blackbox Logs, that describes how to create a log that records a lot of detailed information missing in the common and combined log formats. This information is supposed to help you resolve performance issues. As the author notes "While the common log-file format (and the combined format) are great for hit tracking, they aren't suitable for getting hardcore performance data." The article describes a "blackbox" log format, like a blackbox flight recorder on an aircraft, that gathers information used to profile server performance, missing from the hit tracking log formats: Keep alive status, remote port, child processes, bytes sent, etc. LogFormat "%a/%S %X %t \"%r\" %s/%>s %{pid}P/%{tid}P %T/%D %I/%O/%B" blackbox I'm trying to recreate as much of the format for Nginx, and would like help filling in the blanks. Here's what Nginx blackbox format would look like, the unmapped Apache directives have question marks after their names. access_log blackbox '$remote_addr/$remote_port X? [$time_local] "$request"' 's?/$status $pid/0 T?/D? I?/O?/B?' Here's a table of the variables I've been able to map from the Nginx documentation. %a = $remote_addr - The IP address of the remote client. %S = $remote_port - The port of the remote client. %X = ? - Keep alive status. %t = $time_local - The start time of the request. %r = $request - The first line of request containing method verb, path and protocol. %s = ? - Status before any redirections. %>s = $status - Status after any redirections. %{pid}P = $pid - The process id. %{tid}P = N/A - The thread id, which is non-applicable to Nignx. %T = ? - The time in seconds to handle the request. %D = ? - The time in milliseconds to handle the request. %I = ? - The count of bytes received including headers. %O = ? - The count of bytes sent including headers. %B = ? - The count of bytes sent excluding headers, but with a 0 for none instead of '-'. Looking for help filling in the missing variables, or confirmation that the missing variables are in fact, unavailable in Nginx.

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

< Previous Page | 972 973 974 975 976 977 978 979 980 981 982 983  | Next Page >