Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 98/172 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• How to "restart/repair" an USB port?

  - by Click Ok

  My laptop has two USB ports, but one is broken, so I use a USB hub in the other good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detect the mouse and the keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... Is there some method, software, etc. to "restart/repair" the USB port without restarting the PC?

  Read the article

• SMTP port open - but not open

  - by Frederik Nielsen

  As some of you might know, I am setting up an exchange server. Now I ran into another problem: I cannot connect to the SMTP service from outside the server! The ports are opened in the gateway device (a ZyXEL USG50), Windows firewall is off. I see the packets travekl through the ZyXEL firewall, and I can also see the packets with wireshark on the server, so I know they are getting all the way in to the server. I also know it receives them, and sends out the reply - and this is where things go bad! Analyzing with wireshark, I get these errors in the return packets: Header checksum: 0x0000 [incorrect, should be 0x0779 (may be caused by "IP checksum offload"?)] And: Acknowledgment Number: 0x8e3337d1 [should be 0x00000000 because ACK flag is not set] What the (sorry my French) hell is going on? I really cant figure it out.. Thanks in advance.

  Read the article

• Connect wired-only devices to a remote wireless access point?

  - by billpg

  Hi everyone. In building A, I have a Netgear wireless access point using WPA2. Works great, no problems. In building B, I have some devices that only have wired Ethernet ports. They can't see my access point. What I need is a gizmo that connects over-the-air to my access point in building A, talks WPA2, and converts the packets to and from a wired Ethernet port. Netgear-access-point in building A      (WPA2 WiFi) Wireless bridge device          <-- Looking for this.      (Cat5 ethernet) My devices in building B. I've looked for devices on Amazon, but the descriptions are infuriatingly unclear. It says it supports WPA2, but does it support it as a client? Grrr... Any recommendations please?

  Read the article

• Can iptables allow Squid to process a request, then redirect the response packets to another port?

  - by Dan H

  I'm trying to test a fancy traffic analyzer app, which I have running on port 8890. My current plan is to let any HTTP request come into Squid, on port 3128, and let it process the request, and then just before it sends the response back, use iptables to redirect the response packets (leaving port 3128) to port 8890. I've researched this all night, and tried many iptables commands, but I'm missing something and my hair is falling out. I thought something like this would work: iptables -t nat -A OUTPUT -p tcp --sport 3128 -j REDIRECT --to-ports 8990 This rule gets created ok, but it never redirects anything. Is this even possible? If so, what iptables incantation could do it? If not, any idea what might work on a single host, given multiple remote browser clients?

  Read the article

• ^C not working in zsh on Mac OSX

  - by Vitaly Kushner

  Ctrl-C stopped working for me at the terminal when using zsh (on mac osx). I didn't notice the exact moment that it happend so I can't be sure what caused it. I didd't update zsh in a while though. and didn't touch .zshrc (I have it at a repo http://github.com/astrails/dotzsh) If I run bash, ^C works in it. If I run any command, like cat, ^C will work to stop it too. but inside zsh it just doesn't do anything. bindkey | grep \\^C gives "^B"-"^C" self-insert zsh 4.3.10 (i386-apple-darwin10.4.3), installed though ports (zsh-devel @4.3.10_0+doc+examples+mp_completion+pcre) mac os 10.6.6

  Read the article

• not able to mount media to ESX 4.0

  - by jack8138

  Hi, I have ESX 4.0 running on NEC Express 5800 R-120a model. I have 2 VMs running windows XP. I am not able to mount any media to it. When I try connecting the local media to the VM, the error message comes mentioning "a connection to the host could not be established.: I have checked and there is no network issue. ESX is accessible fine. Any help would be greatly appreciated. Besides, I have opened almost all the ports in the firewall just to make sure there is no port conflict.

  Read the article

• Where does amavisd-new log on ubuntu, by default

  - by Bojan Markovic

  I have a misbehaving amavisd on a mail server. It starts and then silently stops. Init script outputs successful start whan invoked manually, however the next second I check the status and the service is off. Nothing is listening on it's ports. I googled. I checked out the configuration files, I checked out init.d script. It starts, then it stops. And I have no idea what's going on, since I can't find the log file (no it's not /var/log/amavis.log or anything logical like that).

  Read the article

• How to run node.js app on port 80? Are processes blocking my port?

  - by Lucas

  I believe the port 80 on my remote instance is blocked, and I am trying to run a node.js app using port 80. I have experimented with ports 3000 and 3002, and both ports are working fine, but I get an error when running on port 80. I suspect port 80 is blocked from my output of netstat -an below, but how can I find the process id's of the addresses that are blocking port 80 below? [lucas@ecoinstance]~/node/nodetest1$ netstat -an Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:3002 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:27017 127.0.0.1:51108 ESTABLISHED tcp 0 0 127.0.0.1:51106 127.0.0.1:27017 ESTABLISHED tcp 0 0 127.0.0.1:27017 127.0.0.1:51106 ESTABLISHED tcp 0 0 127.0.0.1:51107 127.0.0.1:27017 ESTABLISHED tcp 0 0 10.240.241.116:3002 174.61.171.61:36583 TIME_WAIT tcp 0 0 127.0.0.1:27017 127.0.0.1:51109 ESTABLISHED tcp 0 0 10.240.241.116:42423 169.254.169.254:80 ESTABLISHED tcp 0 0 127.0.0.1:51108 127.0.0.1:27017 ESTABLISHED tcp 0 532 10.240.241.116:22 174.61.171.61:56824 ESTABLISHED tcp 0 0 127.0.0.1:27017 127.0.0.1:51107 ESTABLISHED tcp 0 0 10.240.241.116:42412 169.254.169.254:80 ESTABLISHED tcp 0 0 127.0.0.1:51109 127.0.0.1:27017 ESTABLISHED tcp 0 0 127.0.0.1:51105 127.0.0.1:27017 ESTABLISHED tcp 0 0 10.240.241.116:42422 169.254.169.254:80 TIME_WAIT tcp 0 0 127.0.0.1:27017 127.0.0.1:51105 ESTABLISHED tcp6 0 0 :::22 :::* LISTEN udp 0 0 0.0.0.0:49948 0.0.0.0:* udp 0 0 0.0.0.0:68 0.0.0.0:* udp 0 0 10.240.241.116:123 0.0.0.0:* udp 0 0 127.0.0.1:123 0.0.0.0:* udp 0 0 0.0.0.0:123 0.0.0.0:* udp6 0 0 :::12151 :::* udp6 0 0 :::123 :::* Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 405680 /tmp/ssh-KdkxJfFLpKTC/agent.22 813 unix 2 [ ACC ] STREAM LISTENING 408230 /tmp/ssh-ofUeNNEwAqtP/agent.22 243 unix 2 [ ACC ] STREAM LISTENING 416227 /tmp/mongodb-27017.sock unix 2 [ ACC ] SEQPACKET LISTENING 3692 /run/udev/control unix 7 [ ] DGRAM 5286 /dev/log unix 2 [ ACC ] STREAM LISTENING 5318 /var/run/acpid.socket unix 2 [ ACC ] STREAM LISTENING 16170 /tmp//tmux-1000/default unix 2 [ ACC ] STREAM LISTENING 414450 /var/run/dbus/system_bus_socke And here is the log when trying to run on port 80 with node.js: [lucas@ecoinstance]~/node/nodetest1$ npm start > [email protected] start /home/lucas/node/nodetest1 > node ./bin/www events.js:72 throw er; // Unhandled 'error' event ^ Error: listen EACCES at errnoException (net.js:904:11) at Server._listen2 (net.js:1023:19) at listen (net.js:1064:10) at Server.listen (net.js:1138:5) at Function.app.listen (/home/lucas/node/nodetest1/node_modules/express/lib/applicati on.js:532:24) at Object.<anonymous> (/home/lucas/node/nodetest1/bin/www:7:18) at Module._compile (module.js:456:26) at Object.Module._extensions..js (module.js:474:10) at Module.load (module.js:356:32) at Function.Module._load (module.js:312:12) npm ERR! [email protected] start: `node ./bin/www` npm ERR! Exit status 8 npm ERR! npm ERR! Failed at the [email protected] start script. npm ERR! This is most likely a problem with the nodetest1 package, npm ERR! not with npm itself. npm ERR! Tell the author that this fails on your system: npm ERR! node ./bin/www npm ERR! You can get their info via: npm ERR! npm owner ls nodetest1 npm ERR! There is likely additional logging output above. npm ERR! System Linux 3.13-0.bpo.1-amd64 npm ERR! command "/usr/local/bin/node" "/usr/local/bin/npm" "start" npm ERR! cwd /home/lucas/node/nodetest1 npm ERR! node -v v0.10.28 npm ERR! npm -v 1.4.9 npm ERR! code ELIFECYCLE npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /home/lucas/node/nodetest1/npm-debug.log npm ERR! not ok code 0 And sudo netstat -lnp does not return any matching port 80's: [lucas@ecoinstance]~/node/nodetest1$ sudo netstat -lnp [48/648] Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Progr am name tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 29160/mon god tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1976/sshd tcp6 0 0 :::22 :::* LISTEN 1976/sshd udp 0 0 0.0.0.0:49948 0.0.0.0:* 1604/dhcl ient udp 0 0 0.0.0.0:68 0.0.0.0:* 1604/dhcl ient udp 0 0 10.240.241.116:123 0.0.0.0:* 2076/ntpd udp 0 0 127.0.0.1:123 0.0.0.0:* 2076/ntpd udp 0 0 0.0.0.0:123 0.0.0.0:* 2076/ntpd udp6 0 0 :::12151 :::* 1604/dhcl ient udp6 0 0 :::123 :::* 2076/ntpd Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ACC ] STREAM LISTENING 405680 22814/ssh-agent /tmp/ssh-K dkxJfFLpKTC/agent.22813 unix 2 [ ACC ] STREAM LISTENING 408230 24049/ssh-agent /tmp/ssh-o fUeNNEwAqtP/agent.22243 unix 2 [ ACC ] STREAM LISTENING 416227 29160/mongod /tmp/mongo db-27017.sock unix 2 [ ACC ] SEQPACKET LISTENING 3692 284/udevd /run/udev/ control unix 2 [ ACC ] STREAM LISTENING 5318 1798/acpid /var/run/a cpid.socket unix 2 [ ACC ] STREAM LISTENING 16170 5177/tmux /tmp//tmux -1000/default unix 2 [ ACC ] STREAM LISTENING 414450 28213/dbus-daemon /var/run/d bus/system_bus_socket unix 2 [ ACC ] STREAM LISTENING 404225 22324/1 /tmp/ssh-9 TlDmu4bjl/agent.22324

  Read the article

• SVN Checkout URL - fresh install

  - by Webnet

  I just setup SVN on a server that is running Ubuntu server as a fresh install. I've got it up and running but am having difficult determining how to connect to it. I'm trying to do an import using the local IP address: http://IP/RepositoryName but it's saying it can't resolve the IP. I'm wondering if there's something on the server I need to setup. I have not modified dav_svn.conf because there is another server here that is running SVN (I'm migrating it to a new server) and it's dav_svn.conf is not modified. The current working SVN has a subdomain associated with the IP location of the server but doesn't do anything special with the ports as far as I can tell. I'm getting this error via RapidSVN when I try to import... Error: Error while performing action: OPTIONS of 'http://IP/RepositoryName': could not connect to server (http://IP) Any help would be appreciated

  Read the article

• Problems setting up home web server

  - by putmatrix

  Has anyone been able to get a server working with the router smcwbr14t-g? Although I have been able to get Apache set up correctly and my website works on the internal IP 192.168.2.101, I've been running into a dead end when trying to get it to show up on my external IP. In my router, there is no option for port forwarding, but there are options for a 'virtual server'. Following the manual, I have it set up like this: http://imgur.com/zrcV7.png I also disabled the firewall. I configured Apache to listen to ports 80, 81, and 443, none of which solved the problem. However, the IP's 192.168.2.101:443 and :81 load fine. The problem is that I still cannot load the web site from my external IP, either from my computer or outside.

  Read the article

• Booting from e-sata drive

  - by petersohn

  I have a HP EliteBook laptop (don't know exact product number), which has an internal hard drive with Windows installed on it. I have an external hard drive with e-sata and USB ports, linux installed on it. When I try to boot from the external drive, it works if I use USB but not if I use e-sata. In the BIOS setup, I have the following boot order set: External SATA drive USB Hard Drive Notebook Upgrade Bay Notebook Hard Drive etc. When I boot from another drive (such as the internal hard drive or from CD-ROM), and have the e-sata cable connected, it works perfectly. Is there any way to boot from the e-sata drive?

  Read the article

• Trying to understand why VLANs need to be created on intermediate switches

  - by Jon Reeves

  I'm currently studying for the Cisco switching exam and having trouble understanding exactly how 802.1q tagging works. Given three daisy chained switches (A,B, and C) with trunk ports between them and VLAN 101 defined on both end switches (A and C), I'm not sure why the VLAN also needs to be defined on the middle one (B)? Note that I am not disputing that it does need to be configured, I'm just trying to understand why exactly. As I understand it, traffic from VLAN 101 on switch A will be tagged as it goes through the trunk to switch B. According to the documentation I have read, trunks will pass all VLANs by default, and the .1q tag is only removed when the frame leaves through an access port on the relevant VLAN. From this I would expect switch B to simply forward the tagged frame unchanged through the trunk to switch C. Can anyone shed some light on how switch B processes this frame and why it does not get forwarded through the other trunk ?

  Read the article

• Radeon 5850 Why am I not getting 3 monitors up as a choice ??

  - by Jan

  Ive just bought the top end ATI Radeon card with 2 normal monitor ports and a HDMI. The idea was to continue using my dual screen setup as always and to use the last plug, the HDMI on my TV. I got a new 52 inch HD TV with all the necessary bits. This should work fine. But.. in Display Properties I still get only my 2 monitors up as options. Not the Digital TV. When I unplug 1 monitor and restart the computer, I get the TV and the other monitor. But never all 3 at the same time. Why is this ? Where can I go to tell it that I need all 3 screens at the same time. Also I get a message saying my gfx card also gives sound through the HDMI cable.. But the TV tells me its recieving a sound format that it does not understand. Any ideas on that too while were at it ?

  Read the article

• Multi Thread Rsync Transfer

  - by reefine

  For some reason when running a single rsync command I am getting 1 MB/sec to 2 MB/sec even when I connecting 2 servers both connected to 1 Gbps ports. rsync -v --progress -e ssh /backup/mysqldata/mysql-bin.000199 [email protected]:/secondary/mysqldata/mysqldata/mysql-bin.000199 I have over 800 GB of data to transfer split among 500 or so files all starting with: mysql-bin.000* I've found that running 25-30 rsync simultaneously from seperate SSH windows gets me upwards of 25 MB/sec but it will take me hours to run these all manually. Is there anyway to get the 25 MB/sec from a single rsync command?

  Read the article

• Can i have a Asterisk IP PBX Server Behind ISA 2000

  - by garyb32234234

  Hello Is it a simple procedure to configure ISA Server 2000 to allow an Asterisk IPPBX connect to SIP provider. On asterisk forums they say the ISA has difficulties handling SIP, softphones that i have installed behind the firewall work fine with the provider when the firewall client is installed on the workstation. With asterisk being a linux based system this will not be an option. Is the config a matter setting up port forwarding, is this a more complicated task on ISA server than just selecting the ports i need and then the ip of the internal machine i want to forward them to? UPDATE: I dont think this is possible from what ive researched Regards Gary

  Read the article

• Strange Recurrent Excessive I/O Wait

  - by Chris

  I know quite well that I/O wait has been discussed multiple times on this site, but all the other topics seem to cover constant I/O latency, while the I/O problem we need to solve on our server occurs at irregular (short) intervals, but is ever-present with massive spikes of up to 20k ms a-wait and service times of 2 seconds. The disk affected is /dev/sdb (Seagate Barracuda, for details see below). A typical iostat -x output would at times look like this, which is an extreme sample but by no means rare: iostat (Oct 6, 2013) tps rd_sec/s wr_sec/s avgrq-sz avgqu-sz await svctm %util 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16.00 0.00 156.00 9.75 21.89 288.12 36.00 57.60 5.50 0.00 44.00 8.00 48.79 2194.18 181.82 100.00 2.00 0.00 16.00 8.00 46.49 3397.00 500.00 100.00 4.50 0.00 40.00 8.89 43.73 5581.78 222.22 100.00 14.50 0.00 148.00 10.21 13.76 5909.24 68.97 100.00 1.50 0.00 12.00 8.00 8.57 7150.67 666.67 100.00 0.50 0.00 4.00 8.00 6.31 10168.00 2000.00 100.00 2.00 0.00 16.00 8.00 5.27 11001.00 500.00 100.00 0.50 0.00 4.00 8.00 2.96 17080.00 2000.00 100.00 34.00 0.00 1324.00 9.88 1.32 137.84 4.45 59.60 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 22.00 44.00 204.00 11.27 0.01 0.27 0.27 0.60 Let me provide you with some more information regarding the hardware. It's a Dell 1950 III box with Debian as OS where uname -a reports the following: Linux xx 2.6.32-5-amd64 #1 SMP Fri Feb 15 15:39:52 UTC 2013 x86_64 GNU/Linux The machine is a dedicated server that hosts an online game without any databases or I/O heavy applications running. The core application consumes about 0.8 of the 8 GBytes RAM, and the average CPU load is relatively low. The game itself, however, reacts rather sensitive towards I/O latency and thus our players experience massive ingame lag, which we would like to address as soon as possible. iostat: avg-cpu: %user %nice %system %iowait %steal %idle 1.77 0.01 1.05 1.59 0.00 95.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sdb 13.16 25.42 135.12 504701011 2682640656 sda 1.52 0.74 20.63 14644533 409684488 Uptime is: 19:26:26 up 229 days, 17:26, 4 users, load average: 0.36, 0.37, 0.32 Harddisk controller: 01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 1078 (rev 04) Harddisks: Array 1, RAID-1, 2x Seagate Cheetah 15K.5 73 GB SAS Array 2, RAID-1, 2x Seagate ST3500620SS Barracuda ES.2 500GB 16MB 7200RPM SAS Partition information from df: Filesystem 1K-blocks Used Available Use% Mounted on /dev/sdb1 480191156 30715200 425083668 7% /home /dev/sda2 7692908 437436 6864692 6% / /dev/sda5 15377820 1398916 13197748 10% /usr /dev/sda6 39159724 19158340 18012140 52% /var Some more data samples generated with iostat -dx sdb 1 (Oct 11, 2013) Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sdb 0.00 15.00 0.00 70.00 0.00 656.00 9.37 4.50 1.83 4.80 33.60 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 12.00 836.00 500.00 100.00 sdb 0.00 0.00 0.00 3.00 0.00 32.00 10.67 9.96 1990.67 333.33 100.00 sdb 0.00 0.00 0.00 4.00 0.00 40.00 10.00 6.96 3075.00 250.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 2.00 0.00 16.00 8.00 2.62 4648.00 500.00 100.00 sdb 0.00 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 0.00 100.00 sdb 0.00 0.00 0.00 1.00 0.00 16.00 16.00 1.69 7024.00 1000.00 100.00 sdb 0.00 74.00 0.00 124.00 0.00 1584.00 12.77 1.09 67.94 6.94 86.00 Characteristic charts generated with rrdtool can be found here: iostat plot 1, 24 min interval: http://imageshack.us/photo/my-images/600/yqm3.png/ iostat plot 2, 120 min interval: http://imageshack.us/photo/my-images/407/griw.png/ As we have a rather large cache of 5.5 GBytes, we thought it might be a good idea to test if the I/O wait spikes would perhaps be caused by cache miss events. Therefore, we did a sync and then this to flush the cache and buffers: echo 3 > /proc/sys/vm/drop_caches and directly afterwards the I/O wait and service times virtually went through the roof, and everything on the machine felt like slow motion. During the next few hours the latency recovered and everything was as before - small to medium lags in short, unpredictable intervals. Now my question is: does anybody have any idea what might cause this annoying behaviour? Is it the first indication of the disk array or the raid controller dying, or something that can be easily mended by rebooting? (At the moment we're very reluctant to do this, however, because we're afraid that the disks might not come back up again.) Any help is greatly appreciated. Thanks in advance, Chris. Edited to add: we do see one or two processes go to 'D' state in top, one of which seems to be kjournald rather frequently. If I'm not mistaken, however, this does not indicate the processes causing the latency, but rather those affected by it - correct me if I'm wrong. Does the information about uninterruptibly sleeping processes help us in any way to address the problem? @Andy Shinn requested smartctl data, here it is: smartctl -a -d megaraid,2 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:13 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 20 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 1236631092 Blocks received from initiator = 1097862364 Blocks read from cache and sent to initiator = 1383620256 Number of read and write commands whose size <= segment size = 531295338 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36556.93 number of minutes until next internal SMART test = 32 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 509271032 47 0 509271079 509271079 20981.423 0 write: 0 0 0 0 0 5022.039 0 verify: 1870931090 196 0 1870931286 1870931286 100558.708 0 Non-medium error count: 0 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36538 - [- - -] # 2 Background short Completed 16 36514 - [- - -] # 3 Background short Completed 16 36490 - [- - -] # 4 Background short Completed 16 36466 - [- - -] # 5 Background short Completed 16 36442 - [- - -] # 6 Background long Completed 16 36420 - [- - -] # 7 Background short Completed 16 36394 - [- - -] # 8 Background short Completed 16 36370 - [- - -] # 9 Background long Completed 16 36364 - [- - -] #10 Background short Completed 16 36361 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes] smartctl -a -d megaraid,3 /dev/sdb yields: smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: SEAGATE ST3500620SS Version: MS05 Serial number: Device type: disk Transport protocol: SAS Local Time is: Mon Oct 14 20:37:26 2013 CEST Device supports SMART and is Enabled Temperature Warning Disabled or Not Supported SMART Health Status: OK Current Drive Temperature: 19 C Drive Trip Temperature: 68 C Elements in grown defect list: 0 Vendor (Seagate) cache information Blocks sent to initiator = 288745640 Blocks received from initiator = 1097848399 Blocks read from cache and sent to initiator = 1304149705 Number of read and write commands whose size <= segment size = 527414694 Number of read and write commands whose size > segment size = 51986460 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36596.83 number of minutes until next internal SMART test = 28 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 610862490 44 0 610862534 610862534 20470.133 0 write: 0 0 0 0 0 5022.480 0 verify: 2861227413 203 0 2861227616 2861227616 100872.443 0 Non-medium error count: 1 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 16 36580 - [- - -] # 2 Background short Completed 16 36556 - [- - -] # 3 Background short Completed 16 36532 - [- - -] # 4 Background short Completed 16 36508 - [- - -] # 5 Background short Completed 16 36484 - [- - -] # 6 Background long Completed 16 36462 - [- - -] # 7 Background short Completed 16 36436 - [- - -] # 8 Background short Completed 16 36412 - [- - -] # 9 Background long Completed 16 36404 - [- - -] #10 Background short Completed 16 36401 - [- - -] #11 Background long Completed 16 2 - [- - -] #12 Background short Completed 16 0 - [- - -] Long (extended) Self Test duration: 6798 seconds [113.3 minutes]

  Read the article

• Firewalling gateways and IDS's

  - by Scott Davies

  Hi, For IDS, I plan to have a Win 2008 server running on the gateway with the majority of roles disabled. I plan to firewall the Internet connection, but I'd also like to install Snort to work as an IDS. However, I am guessing that regardless of the Snort install of the promiscuous Winpcap driver, I won't be able to monitor ports that the firewall blocks. My thinking is that chain of flow is: Internet-Firewall on Win 2008-Winpcap-Snort-internal network Is there a way to still monitor services that the firewall will block (i.e. TCP 445 SMB) ? Perhaps run the data through Snort and then through the firewall ? Thanks

  Read the article

• Unable to access Citrix XenApp 6 published applications externally

  - by Christopher McCann

  We are trying to use a trial of Citrix XenApp 6 Fundamentals to virtualise a couple of applications as a proof of concept. We haven't ever used it before so I confess to be a noob with it. We can connect to the XenApp web interface, and the iPad app will connect and list the applications, but the applications themselves will not load. I discovered in the .ica file that it was attempting to connect to the internal IP address of the server instead of its static external. I have been following various threads on Citrix but nothing seems to have fixed it for me. The server is deployed on an EC2 instance with a static elastic IP. All the ports are opened and I can telnet into the XenApp server on 1493 and I get the ICA response. I have also run on ALTADDR and provided the external IP address. Does anyone have any ideas?

  Read the article

• Windows Firewall issues

  - by Will Vousden

  I'm not sure whether this is a Windows problem or a .NET problem (i.e. whether it belongs here on on SO), but I've written a small HTTP server program in C# (using the .NET HttpListner class) which works fine for the most part, but Windows Firewall seems to be refusing to let connections through to it from anything other than localhost. I've added exceptions for TCP and UDP in the "Inbound Rules" section of the firewall settings, essentially duplicating existing rules for other HTTP-based services which work fine (e.g. foo_httpcontrol). Specifically, I've added separate rules for TCP and UDP connections covering all ports, specific to the executable I'm running. There's no problem when Windows Firewall is disabled, but if I enable it, the connection simply times out.

  Read the article

• Tomcat and IIS6 on one server, multiple websites

  - by Rafe

  Windows Server 2003 with IIS6 and Tomcat 6.0.26. Three sites running on this server. One is PHP, one is ASP and the third uses Tomcat. The first two work flawlessly. The third is being a pain. Tomcat is installed and if called on the server itself by IP address xxx.xxx.xxx.xxx:8080 shows the welcome page. Calling the same address from an external machine gives a 'could not connect' error. Calling the ip address from within the server on standard port 80 gives me an error 324 (net::ERR_EMPTY_RESPONSE). Have tried using httpcfg to force listening only on ports within the ip range I'm using in a manner similar to question 35650 located here on serverfault but with no success. There are actually ten ip addresses on this machine but I'm only using three of them at this point. Any pointers on troubleshooting this would be appreciated!

  Read the article

• IOGEAR KVM cannot reset admin account

  - by George Horlacher

  According to the manual you can do a cold reset by holding the reset button in for 3 seconds. This does seem to reset it but the username and password are not reset... I've tried the keyboard hotkeys - Num-Lock and minus sign (-) to get into hotkey mode and then use the "r" and "" to reset to factory defaults but that doesnt seem to do anything either. It just reverts to User1. I'm not sure what the default admin username should be but admin doesnt seem to work I need to get to the admin menu to name the ports but cannot get access. Any ideas? Using GCS1758 manual with no luck.

  Read the article

• Two Tomcat SSL Providers & One FreeBSD

  - by mosg

  Hello everyone. Question: On FreeBSD8 I need to have two opened HTTPS different ports (443 and 444, for example). In other words, I need two providers, working simultaneously: Ordinary SSL signed certificate (# Thawte) on 443 port Special russian security provider (# DIGTProvider, based on CryptoPro CSP software) on 444 port I also have to mentioned, that the major provider is the 2'nd provider. Here is some of DIGTProvider options: add to ${JRE_HOME}/lib/security/java.security this line security.provider.N=com.digt.trusted.jce.provider.DIGTProvider ssl.SocketFactory.provider=com.digt.trusted.jsse.provider.DigtSocketFactory uncomment and edit in conf/server.xml HTTPS section: sslProtocol="GostTLS" (added) edit bin/catalina.sh and add: export LD_LIBRARY_PATH="${LD_LIBRARY_PATH}:/opt/cprocsp/lib/ia32" export JAVA_OPTS="${JAVA_OPTS} -Dcom.digt.trusted.jsse.server.certFile=/home//server-gost.cer -Dcom.digt.trusted.jsse.server.keyPasswd=11111111" As I know if I just define in server.xml tomcat's configuration file two SSL connectors, tomcat would not start, because in JRE you can use only one JSSE provider. Thanks for help.

  Read the article

• Unable to make my bios see my sata hdd

  - by Stefan

  I know there are many question about that, but I tried everything and I'm still not able to make my bios see my sata2 hdd. I've got a QDI motherbord with no sata port; only 2 ide ports. I had an old ide hdd, now i've removed it and bought a sata2 hdd. Since my pc has no sata slots i bouth a ide-to-sata adapter. So, i don't have any os installed on the new drive, and the old drive is removed. My problem is that I'm unable to see my hdd on bios. I suppose that my bios, since it's an old version, doesn't have sata drivers, but I don't know if I must install it and also I dont know how to do it. Anyone can help me?

  Read the article

• MRTG + RRDTool Hourly Graph

  - by SuperMicro321

  I am using MRTG + RRDtool to monitor the bandwidth on each switchport of a Cisco Catalyst 2950 via snmp. Is MRTG capable of generating an hourly graph? With RRDtool I was able to set the interval to 1 minute in hopes of getting a more detailed graph, but the shortest timeframe the graph is 'Daily' graph (5 Minute Average) and the image is too small. What I am looking to get out of this: I am looking to be able to visually monitor all of the switch ports and tell when port begins to have unusually high traffic, in real time (1 minute interval of snmp poll, graphs generated, and page refreshed).

  Read the article

• How can I stop my laptop display from flickering when I connect my TV?

  - by Lord Torgamus

  I have a laptop with an HDMI output port running Vista, and an HDTV with HDMI input ports. The laptop is set to extend its desktop onto a second monitor. When I connect the computer to the TV with an HDMI cable, my laptop screen usually flickers rapidly. Most of the time it lasts for about 30 seconds, but sometimes it lasts for several minutes and once in a while it doesn't happen at all. It wouldn't be so bad except that the cursor moves back to the center of the laptop screen with each flicker, so I can't really do anything until the machine decides it's ready to calm down. I haven't been able to find any pattern at all for the causes or duration of the flickering. It doesn't seem to matter what programs the laptop is running when I connect it to the TV, whether I enable the extended display before or after I connect the TV or which HDMI port/cable I use. What could be causing this, and how can I make it go away?

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >