Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 103/172 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

  • Dual-WAN router

    - by aix
    I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

    Read the article

  • How can I use 2 monitors plus laptop with my Dell e6420 w/ Nvidia nvs 4200m

    - by KallDrexx
    I have just hooked up a 2nd external monitor to my Dell e6420 laptop with a Nvidia NVS 4200m graphics card, running Windows 8 64 bit. However, the computer won't let me have both monitors and the laptop display active at the same time. I installed the latest Nvidia graphics drivers (310.70) but it claims that my GPU can only support up to 2 monitors. Nivdia's website implies differently (as does various other laptops around the office). The monitors are connected both via DVI to my dell docking station that has multiple DVI ports. Both monitors are working correctly, I just can't get all 3 working together. Attempting to download the driver from dell fails, as their driver installer is broken apparently Any ideas?

    Read the article

  • infiniband network between 3 servers

    - by grumpf
    Let's say I have 3 different servers, each one with an infiniband card. Each card has 2 different ports. (I don't know about the model yet) Is it possible to create 3 different networks and to allow the 3 servers to communicate with each other without any problems? (and any spof). I guess I just have to setup the /etc/hosts correctly. I really don't know about infiniband, so please help me :) Thanks in advance. EDIT: Point is to NOT USE a switch!

    Read the article

  • What are the IPv6 Public and Private and Reserved ranges

    - by vipin raj
    I just want to know what are all the public IPv6 ranges which ISPs or other users can use? Also need a list of addresses which can be used in private networks and also the list of addresses which never can be used in any network. I have been searching through different web sites. But none gives a reliable answer. Actually we are developing an application which allows user to plan their IP address(create supernets, subnets, hosts, assign host to ports etc). So my application should be able to distinguish between all kinds of address ranges, whether it is reserved, public, private, multicast etc

    Read the article

  • Code deploy system [closed]

    - by Turnaev Evgeny
    Currently we deploy code to servers in a various ways: freebsd package freebsd ports part of config files and static just svn up'ed and a symlink is changed to new upped folder The distribution of freebsd packages to target servers is done through custom tool that uses ssh. I am looking for a code deploy system that will allow: deploy several packages (freebsd or linux) atomic (ether deploy all or none of them to server) can save a history of last stable version - so in case of bad deploy i can easily rollback to last working version all servers ease deployment of config and static files - and integrate those into atomic deploy/rollback system. should work with freebsd or linux (apt-get system)

    Read the article

  • Load balancing with Cisco router

    - by you8301083
    I have a Cisco router with two bonded T1's which are setup as a VPN to the main office. We need more bandwidth but can't get other connections (or it's too costly), so I would like to have a dsl connection installed. This DSL connection will run over a VPN to the same main office, but it won't be bonded with the T1's - so it won't act as a single connection. Since the three circuits won't act as a single connection (basically would be two connections 2 T1's + 1 DSL) we would have to split the network in half - but I don't want to do that. Instead, would it be possible to send all HTTP/HTTPS over the DSL connection but send all mission critical data (such as voice/active directory) over the T1's? I basically want to send specific ports over DSL and everything else over the T1's without separating half of the users traffic over the DSL and the rest over the T1's.

    Read the article

  • Mounting Gluster Volumes

    - by Roman Newaza
    I have created Hosted Zone with 2 IP addresses of Gluster Cluster, both IP are returned by dig. After mounting Gluster, I cannot ls mount point as it takes long time. mount shows me it's mounted, but df doesn't. Finally, I have this: ls: cannot access /mnt/storage: Transport endpoint is not connected. But if I mount it with the one of the IP, no problem - volume contents is accessible OS: Ubuntu 11.10 GlusterFS: 3.2.6 Log: http://pastie.org/private/2jgp4h1hnqgzych3djtg I have can telnet storage from client - ports are open.

    Read the article

  • Is it possible to backup an SQL Database hosted on an Azure VM, to our internal DPM2012?

    - by Florent Courtay
    I've got an SQL database on an azure VM (non domain) that i'd like to backup to our internal DPM 2012 server. I've installed the DPM agent on the Azure VM, setup DCOM to use only the ports 5000 to 5025 on both the VM and the DPM server, created the 135, 5000-5025, 5718 5719 endpoints on azure and on the VM's firewall. When trying to add this agent to the DPM server, I end up with an error, "Unable to contact the protection Agent on server .cloudapp.net" I know there is some sort of connection between them, as using a wrong password gives me an Invalid Credentials error. The error seems to be DCOM related : When trying to connect to the Azure VM from the DPM server using VBEMTest, i get an Error "0x800706ba The RPC server is unavailable", but access is deneid when using wrong credentials ) What am i missing ? Has someone been able to achieve this kind of setup ? Thanks for your help !

    Read the article

  • Self-hosted browser-based remote desktop script?

    - by rlsaj
    I need a self-hosted browser based remote desktop script that will connect me from any PC to my work PC. I need to either host this script within my own dedicated hosting or on my work PC. The PC that I need to remote into is always the one PC (Win7) and the IP never changes, and I have access to the Router/Firewall within. I have tried many remote desktop services and applications - LogMeIn, Team Viewer, (Ultra/Tight) VNC, GoToMyPC and iTeleport Connect and even Windows Remote Desktop - and the web services (or ports) are blocked at whatever free wi-fi/hotel/coffee shop I am at. Note that I will need to be able to access this from any PC, so I won't be able to install any applications (or use any portable software) - hence my thinking that it will need to be browser based on a standard (not blocked) port. If I can set up a web based remote desktop application - really a homebrew LogMeIn - then I should solve my problem. What is the best option here?

    Read the article

  • Configuring ejabberd on ubuntu ami of amazon ec2

    - by andy
    This is my first experience with ejabberd. Spare me if I miss anything. I have installed ejabberd server on ubuntu 12.04 AMI on Amazon EC2. I have successfully installed the server, added the admin user and host in the config file and opened up reqd ports (5222, 5223, 5269, 5280). Now I tried to login the web admin interface using the admin user id and password. I could log in, BUT I could only see one section, Virtual Hosts. No Control Lists, Access rules, Nodes and Statistics Menu items on the left. Also, when I click Virtual Hosts Menu item, the page that comes up does not show anything. Here are the screenshots

    Read the article

  • USB port not recognising mouse on first bootup

    - by Pacifika
    On a computer here when first powered on the USB wired mouse is not recognised. The light under the mouse is not lit up. Other usb hub's and keyboards work fine. Disconnecting it and reconnecting it fixes the issue, even after a restart - after the pc is switched off for a length of time (for example overnight) the problem reappears. I swapped the mouse, updated the bios and installed updated intellimouse drivers, turned of power saving on the usb ports. Any ideas?

    Read the article

  • Restrict a port to a single app

    - by viraptor
    I'd like to restrict a range of udp ports to a single application (or a user). What I'd like to achieve is not simply blocking a bind() from other uids, but also remove the range from a pool that can be auto-assigned. For example, if someone tries to explicitly bind 12345, but doesn't run the specified app, they should get EPERM. If someone tries to bind an unspecified port, they should never try to bind 12345 at random. Is there any system that can help here? I tried browsing apparmor / selinux docs, but they seem to do the blocking part only.

    Read the article

  • Recommending simple appliance for DansGuardian, iptables, snort inline

    - by SRobertJames
    I'm currently using a Linksys E2000 with dd-wrt. I'd like to add DansGuardian for Content Filtering and snort-inline for IPS; but those require a more powerful box (mainly, more storage). Can you recommend a good device to use? I'm open to both overwrite-the-firmware (like dd-wrt) and designed-to-be-customized boxes. Requirements: 1. 5+ Ethernet ports, pref. GigE 2. small form factor 3. No noise (office environment) 4. low power 5. Not sure about 802.11 wireless Budget < $400, pref. less.

    Read the article

  • How do I fix Nginx config to work with multiple hosts of Unicorn?

    - by fred deAlmeida
    I have no problem instantiating multiple instances of unicorn on different unix sockets and ports. Works fine if I do url:port. My problem comes in correctly formatting nginx.conf to allow multipe upstream conditions. Whatever i do does not seem to work. One instance is fine works fine. Multiple gives me a ""upstream" directive is not allowed here error I am using the base nginx sample from the unicorn site. and doubling up the upstream area with differing terms. each is part of the http set. Any help would be amazing!

    Read the article

  • Slow LAN transfer from 3rd party computer

    - by Chris
    Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

    Read the article

  • if there are multiple kernel module can drive the same device, what is the rule to choose from them?

    - by Dyno Fu
    both pcnet32 and vmxnet can drive the device. $ lspci -k ... 02:01.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 10) Subsystem: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] Flags: bus master, medium devsel, latency 64, IRQ 19 I/O ports at 2000 [size=128] [virtual] Expansion ROM at dc400000 [disabled] [size=64K] Kernel driver in use: vmxnet Kernel modules: vmxnet, pcnet32 both kernel modules are loaded, $ lsmod | grep net pcnet32 32644 0 vmxnet 17696 0 mii 5212 1 pcnet32 as you see, kernel driver in use is vmxnet. is there any policy/algorithm in kernel how to choose from the candidates?

    Read the article

  • What is the maximum number of TCP connections I can have in Windows Server 2008?

    - by evilfred
    I would like to have as many connections (single connections from many different clients) as humanly possible in a server running on Windows Server 2008, in order to support a Comet-style application. The application is written in C#. The connections will not be chatty, they just need to be open (and stay open). Buying boatloads of memory and fast CPUs are not a problem. As far as I can tell, I will be limited to 65k simultaneous open connections per NIC - the maximum number of ports. Is this accurate? Or can I go beyond 65k connections / NIC somehow? It seems like there are server products for Linux at least that support hundreds of thousands of connections. How do they do this?

    Read the article

  • Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

    - by Victor Sergienko
    I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

    Read the article

  • AXFR problem using gradwell secondary DNS

    - by Roaders
    Hi All I use Gradwell.com to provide secondary DNS but I keep getting e-mails along the lines of the following saying that it's not working: You have asked us to provide a secondary DNS service for the following domain(s) Unfortunately, the primary DNS server(s) you specified are not permitting the necessary zone transfers from our servers, or they are not answering "SOA" queries for your domain correctly. I have gone through the support procedure and they weren't that helpful. They have suggested the following: Our secondline team have suggested setting the AXFR to use anouther machine. This will ensure that the transfer is not locked down to one machine and should allow any machine to make the request I don't really know what AFXR is and I only have 1 production machine so I can't set the AFXR to use another one! In previous support correspondence we confirmed that I am allowing transfers to the correct IP and that I have the correct ports open on the firewall. I am running Windows Server 2003. What can I do to try and get these zone transfers working? Thanks

    Read the article

  • After enabling raid0, blue screen of death

    - by thegreyspot
    Hi! Im trying to get a raid0 setup going. I have a 750 gb hdd with the OS on it and two 80gb HDD. For right now, I just want to raid0 on the two 80Gb hdd. When I enable raid in my Bios, Win7 has a BSOD during boot. As far as I understand I need to install raid drivers. However how can I do this? The win7 DVD doesnt seem to have a driver install option. Any suggestions? Thanks EDIT: I saw that there was as seperate setting for the 4th and 5th sata ports. So I pluged in my OS drive into there and left it on IDE. Still didnt work though, am I miss understanding that idealogy?

    Read the article

  • Questions about Domains and DNS

    - by ShoX
    Hi, I am totally new to the DNS and server hosting world and not quite sure what I need. I want to get a domain, forward it to my own server, so that the user sees example.com in the url bar and example.com/foo/bar will work. Depending on what subdomain it is, it should do different things (another base-directory at webserver, ftp, etc). Also my email should be able to be sent to and received by that server. What irritates me, is the fact, that in the A-record I can only list IP-addresses and no ports. So do I have to set up a nameserver on my own server? Or do I accomplish this via vhosts on my webserver? I would appreciate any help or link to a tutorial. I know how DNS works, know some basic apache-stuff, etc... so no need to explain that. Thanks

    Read the article

  • Set up a root server using Ubuntu and Virtualization

    - by Daniel Völkerts
    Hello, I'd like to setup a fresh root server and install a linux based virtualization on it. My thoughts are on: Intel VTs Hardware Ubuntu 9.10 KVM based virt. The access to the root server will only be SSH for Administration. Has anybody done this before, what was your glues discovered in the daily use? My requirements are: very secure, so the root server only has ssh to the dom-0 and minimalistic ports for the guest (e.g. http/s). good monitoring of host/guest (my idea is to using zabbix for it) easy and fast administration (how are the command line tools working for you? cryptiv? high learning curve?) I'm pleased to learn from your suggestions. Regards, Daniel Völkerts

    Read the article

  • Debugging an IP Camera

    - by Kevin Boyd
    Further to my previous question on ServerFault here, I finally can view the stream on RTSP however I still cannot view the camera stream in a web browser. The IP camera uses an activeX control in Internet Explorer. And although I can configure the camera settings from IE, I cannot view the stream it shows connecting for a few sec and shows disconnecting. I have forwarded the HTTP, RTSP and Stream ports of the IP camera. the public port is 7071 and private port is 7070. When I try to see the connections in TCPView it shows that the ActiveX control in IE is trying to connect to port 7070 which is quite unusual since it should connect to 7071 Also the state shows SYN_SENT for sometime and then disconnects. I have really no clue what's going on and why?

    Read the article

  • Debian pure-ftpd, Restrict access

    - by durduvakis
    I am running Debian Wheezy, with ISPConfig 3, plus ModSecurity and I would like to restrict access to ftp to specific IP(s) globally (not to specific ftp users only), that can be either 127.0.0.1 or one I would manually add later. I would also like to completely disable ftp access from the web, but allow only from ftp-client software (if that is possible). The idea of closing firewall ports is not what I want. I know I can do this setting some firewall rule though, but that is not what I currently need. I have managed to do this for example on phpmyadmin inside it's .conf file, but unfortunately I cannot find any configuration to alter for pure-ftpd in my system. Restricting web-ftp access maybe possible by adding some rule in apache2 conf, but I am not sure how to write such a rule. Thanks to everyone that can help cheers

    Read the article

  • Unable to open up port 80 on EC2 using elasticfox

    - by uswaretech
    I have launched an instance of EC2. Initially the security group I created did not have the port 80 open. I sshed and installed Apache etc, and now want to open port 80. I am using elasticfox. So I go to Security Group - [My Group name] - Grant new permission Open up the port 80(Http with TCP) for network range 0.0.0.0/0 Now my assumption is that these ports should be opened up on the instance, but the instance is not responding on the allocated IPs, public DNS entry. What should I do next?

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >