Search Results

Search found 27232 results on 1090 pages for 'mind mapping software'.

Page 981/1090 | < Previous Page | 977 978 979 980 981 982 983 984 985 986 987 988  | Next Page >

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• What kind of hosting do I need? [closed]

  - by Robert Smith

  I have been trying to answer this question but I haven't found an specific answer to my situation. As I want to pay for what I need, I thought I could get a good answer here. I have custom made forum (rather than a built-in forum like the ones you can find as plugins, e.g. WP-Forum or phpBB type of software) in Django. I don't want to use Apache and modwsgi because it's usually very memory-hungry and I can't afford a big server. I prefer a combination of nginx and gunicorn which I think is very efficient (maybe you can also tell me what you think about that). I'm expecting to receive 10,000 to 20,000 visits each month with 15,000 to 30,000 page impressions. I have reviewed some cloud services like Amazon EC2 or Rackspace and other more traditional services (Linodo). This site won't use videos or big images and I certainly don't need a huge amount of bandwidth (200GB would be definitely too much). I need shell access so shared hosting is out of the question. What do I need to run a website like that without problems? What about RAM? 256MB would be enough (that's the amount of RAM offered by small instances in Amazon and Rackspace)? Do you know of any alternative to those I mentioned? If you need more information to provide a useful answer, please don't hesitate to ask. Thanks a lot.

  Read the article

• Isn't a hidden volume used when encrypting a drive with TrueCrypt detectable?

  - by neurolysis

  I don't purport to be an expert on encryption (or even TrueCrypt specifically), but I have used TrueCrypt for a number of years and have found it to be nothing short of invaluable for securing data. As relatively well known free, open-source software, I would have thought that TrueCrypt would not have fundamental flaws in the way it operates, but unless I'm reading it wrong, it has one in the area of hidden volume encryption. There is some documentation regarding encryption with a hidden volume here. The statement that concerns me is this (emphasis mine): TrueCrypt first attempts to decrypt the standard volume header using the entered password. If it fails, it loads the area of the volume where a hidden volume header can be stored (i.e. bytes 65536–131071, which contain solely random data when there is no hidden volume within the volume) to RAM and attempts to decrypt it using the entered password. Note that hidden volume headers cannot be identified, as they appear to consist entirely of random data. Whilst the hidden headers supposedly "cannot be identified", is it not possible to, on encountering an encrypted volume encrypted using TrueCrypt, determine at which offset the header was successfully decrypted, and from that determine if you have decrypted the header for a standard volume or a hidden volume? That seems like a fundamental flaw in the header decryption implementation, if I'm reading this right -- or am I reading it wrong?

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

• Modifying value of "Rating" column within Explorer for arbitrary file types

  - by Fake Name

  Basically, I have a large body of assorted media (text, images, flash files, archives, folders, etc...) and I'm attempting to organize it. Windows Explorer has a rating column, but there seems to be no way to modify the rating of the files short of opening them in their type-specific software (e.g. Media player, or Photo viewer). However, this does not work when the file is of an unsupported type (.rar, .swf ...), or a directory. I'd be more than willing to consider a file-manager replacement (I've alreadly looked at quite a few, Directory Opus, Total Commander, etc...), or even a solution that stores the rating metadata in a hidden file in each folder, or a separate database. The one real critical requirement is the ability to sort by rating, and being filetype-agnostic. Basically, is there any way to categorize a large collection of assorted files by rating that will work with any file type, including directories? - Ideally, there would be an easy way to add arbitrary columns to windows explorer, and edit them directly. However, there seems to be no way to do this. The rating column is the next best thing.

  Read the article

• Access an external SSH server through a restrictive proxy [on hold]

  - by Cyrille

  I'm a software developer. I wish to access my computer at home through SSH. For example, I sometime need to access my personal projects source code to check how I handled specific problems. Unfortunately, I currently work under an over-restrictive and anti-productive proxy that waste a hell of a lot of everyone's time (We often have to visit websites from our smartphones or use a web proxy to check very legitimates websites for answers, and don't get me started on other "security" overkill features we have to cope with...). Well, back to the subject, I can access my home computer from my phone (SSH, port 22 and 80 both redirected by router on port 22). It works, but it's quite uncomfortable. From my office computer, this is what I tried so far: export http_proxy=http://user:pass@proxyip:8080 echo "user:pass" > ~/.corkscrew-auth echo "ProxyCommand corkscrew proxyip 8080 %h %p /home/me/.corkscrew-auth" > ~/.ssh/config ssh 82.23.34.56 -l me -p 80 Proxy could not open connnection to 82.23.34.56: Forbidden ssh_exchange_identification: Connection closed by remote host (same without -p 80) Without corkscrew: ssh: connect to host 82.23.34.56 port 80: Connection timed out ssh: connect to host 82.23.34.56 port 22: Connection timed out Any other idea ?

  Read the article

• Skipping nginx PHP cache for certain areas of a site?

  - by DisgruntledGoat

  I have just set up a new server with nginx (which I am new to) and PHP. On my site there are essentially 3 different types of files: static content like CSS, JS, and some images (most images are on an external CDN) main PHP/MySQL database-driven website which essentially acts like a static site dynamic PHP/MySQL forum It is my understanding from this question and this page that the static files need no special treatment and will be served as fast as possible. I followed the answer from the above question to set up caching for PHP files and now I have a config like this: location ~ \.php$ { try_files $uri =404; fastcgi_cache one; fastcgi_cache_key $scheme$host$request_uri; fastcgi_cache_valid 200 302 304 30m; fastcgi_cache_valid 301 1h; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/php-fastcgi/php-fastcgi.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/example$fastcgi_script_name; fastcgi_param HTTPS off; } However, now I want to prevent caching on the forum (either for everyone or only for logged-in users - haven't checked if the latter is feasible with the forum software). I've heard that "if is evil" inside location blocks, so I am unsure how to proceed. With the if inside the location block I would probably add this in the middle: if ($request_uri ~* "^/forum/") { fastcgi_cache_bypass 1; } # or possible this, if I'm able to cache pages for anonymous visitors if ($request_uri ~* "^/forum/" && $http_cookie ~* "loggedincookie") { fastcgi_cache_bypass 1; } Will that work fine, or is there a better way to achieve this?

  Read the article

• In need of assistance for recovering a lost partition

  - by Tek

  The program that has worked for the most part is Active@ Partition Recovery. I'm so close but yet so far from recovering my data. Okay so here's what happens. In the following screenshot (blanked out a folder and filename with profanity in case some of you guys are at work :P), it detects the partition I accidentally deleted with ALL 100% of my data listed. Of course, I didn't write ANY data to that drive after I did this. But when I click "recover" and finishes the recovery process, in Windows I click on the partition that was just was just recovered... It's EMPTY. The program seems to be able to see my lost files, but when I recover the partition windows doesn't seem to think the same =( Things I tried: I tried running a chkdsk /r /f after I recovered the partition, apparently it couldn't find any errors. Tried using other software like TestDisk to recover the partition, but they (all) act similar to Windows in that it detects the (missing) partition but when I browse it there's no files. The partition is there along with all the file and data information. The sector information is also in the screenshot, is there any way I can use this to my advantage in recovering my data? Other information: Dualboot: Win8 / Ubuntu 12.10 x64 1TB Internal desktop drive, GPT Layout, NTFS formatted drive, 64K allocation size.

  Read the article

• Managing SharePoint permissions via Active Directory?

  - by rgmatthes

  My company has thousands of employees organized thoroughly via Active Directory. I have confidence in the accuracy of the Department and Title information displayed in the user profiles. I'm helping to put up a brand new SharePoint 2007 site, and I contacted IT about managing the site's permissions through AD Groups. The goal is to have the site automatically assign read/write/contribute/whatever permissions based on the information in AD. For example, we could create an AD Group called "Managers" that would contain anyone with the "Manager" title in their AD user profile. I would have SharePoint tap into this AD Group to mass assign permissions if I knew all managers would need a certain level of access (read/write/contribute/whatever). Then if a manager joins the company or leaves it, the group is automatically updated (provided AD gets updated, of course). My IT rep called back and said it couldn't be done. This seems like a pretty straightforward business requirement, and one of the huge benefits of having Active Directory, but maybe I'm mistaken. Could anyone shed some light on this? A) Is it possible to use dynamically-updated AD Groups when assigning permissions via SharePoint? (Does anyone know of a guide I could show my doubtful IT rep?) B) Is there a "best practice" way to go about this? I've read some debate on whether SharePoint Groups or AD Groups are the way to go. My main concern is dynamic updating. C) If this isn't available out of the box, can someone recommend third-party software that will provide the functionality I'm looking for? A big thanks to anyone who can help me out!!

  Read the article

• Workaround for Dell "Power Supply Not Recognised" issue

  - by Haedrian

  So, I have a Dell Inspirion and the power supply port appears to be damaged. Basically when I plug it in I get a nice popup telling me that it couldn't detect that its a Dell power supply so it won't charge the battery and underclocks the system. It still works for other purposes (that is, giving power) I thought it was the actual power supply cable so I bought a new one, that worked for a while, provided I inserted it at JUST THE RIGHT angle. But now that's not working anymore, so I assume its the part which connects to the computer. The battery charging I can live without, the underclocking I can't. I'd like a way around this issue. Things I've tried: Updating the BIOS Replacing the power supply cable Inserting it at different angles Turning it off and on again Swearing at it Twisting it while inserting it So, is there a workaround somehow? I'd like to avoid taking out my soldering kit and risking permanently damaging expensive equipment if that's allright. I'm hoping for a software solution. Added: The exact model is a Del Inspirion N5010

  Read the article

• RAID5 issue after replacing motherboard and upgrading firmware

  - by 8steve8

  ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with Windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. This screenshot should show that the SNs match, which raises the question why the software doesn't realize the drive is a member of the array. I'd like to know if anyone has experienced anything similar, and what should I do, can I force the drive to be recognized as a member (without wiping data)?

  Read the article

• Best way to create and restore a Drive Image with Windows 7? [closed]

  - by jasondavis

  Possible Duplicate: Want to create a system image I am about to build a new PC. I am a windows 7 user. For years now I have been wanting to install windows and all my favorite software, music, etc., and then make a drive IMAGE and be able to go in 6 months later or WHENEVER I want to start fresh and completely format my drives and restore my IMAGE and have all my settings, programs, etc be just5 like when I created the original image. I know there is many ways to do this but I have never done this 100% successfully and I have about a week to figure out how to do it perfectly for when I build my new PC. I have heard good things about using tried Acronis true image in the PAST for doing what I describe4, I tried using it but, but the newer versions are overly complex and don't even seem to work the way I hoped. I also see that Windows 7 has some sort of drive IMAGE creator itself as well. Does the newer Windows 7 image creator do what I am describing above? If it does do what I am asking for (complete drive image with windows, all programs and settings) saved to an IMAGE file that can easily be restored to ANY hard drive in the future? Please share your experiences, tips, ideas on how to achieve this the easiest and most reliable way please

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• All computers on network get stuck waiting for some sites indefinetely

  - by zacaj

  This happens across three computers, running windows 7 and Ubuntu, firefox, opera, and chrome (all latest versions). I am connected to the internet through a Verizon wireless usb modem. When I try to open some web pages they will never finish loading (and usually never even show anything). The status bar at the bottom of the browser will display "Waiting for X" The servers it gets stuck on include: platform.twitter.com s7.addthis.com connect.facebook.net ajax.googleapis.com 2mdn.net Ive been getting away with just blocking them in AdBlock up until now, however the last two have been causing problems. There are some sites which require googleapis.com to load correctly, and some that wont ever load unless its blocked. eBay requires access to 2mdn.net to load pictures. On top of this its getting really annoying having to update AdBlock across all these computers whenever a new site pops up. I'm hoping there's some easier way to fix this? The different sites causing the freeze indicate to me that it's either a problem on my end (somehow?) or some server side software that got updated with a new bug?

  Read the article

• Apache APC (Windows) Can I optimize these APC settings more?

  - by ar099968

  I would like to optimize APC some more but I am not sure where I could do something. First here is the stats after 1 week of running with the current configuration: General Cache Information APC Version 3.1.9 PHP Version 5.4.4 APC Host XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Server Software Apache Shared Memory 1 Segment(s) with 128.0 MBytes (IPC shared memory, Windows Slim RWLOCK (native) locking) Start Time 2014/06/08 05:00:00 Uptime 6 days, 11 hours and 55 minutes File Upload Support 1 Host Status Diagrams Memory Usage Free: 99.7 MBytes (77.9%) Used: 28.3 MBytes (22.1%) Hits & Misses Hits: 510818 (99.9%) Misses: 608 (0.1%) Detailed Memory Usage and Fragmentation Fragmentation: 0.60% (609.8 KBytes out of 99.7 MBytes in 83 fragments) File Cache Information Cached Files 693 ( 35.4 MBytes) Hits 5143359 Misses 1087 Request Rate (hits, misses) 13.24 cache requests/second Hit Rate 13.24 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.01 cache requests/second Cache full count 0 User Cache Information Cached Variables 0 ( 0.0 Bytes) Hits 0 Misses 0 Request Rate (hits, misses) 0.00 cache requests/second Hit Rate 0.00 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.00 cache requests/second Cache full count 0 Runtime Settings apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters -/apc.php$, -/apc_clean.php$, -.tpl.cache.php$, -.tpl.php$, -.string.cache.php$, -.string.php$ apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 2M apc.num_files_hint 7000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 128M apc.shm_strings_buffer 4M apc.slam_defense 0 apc.stat 1 apc.stat_ctime 0 apc.ttl 7200 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 7200 apc.write_lock 1

  Read the article

• Windows 7 / TCP/IP network share guide - looking for to resolve failure to mount lacie network drive but works on XP,Linux,Mac.

  - by Rob

  Can anyone advise me of a really good, readable, Windows 7 TCP/IP network share guide, book, or reference. I want this because I cannot mount my Lacie 2big ethernet network drive in Windows 7 (32 bit home), but I can mount it in Windows XP Home 32bit, Ubuntu Linux 10.04 and Apple MacOS X. This drive is being mounted via the accompanying Lacie Ethernet Agent in XP (which I believe uses "Bonjour" protocol), on Mac and Linux it works without further need for software. Another Super User user has the same problem, but no answer: Trouble accessing network drives in Windows 7 I hope my take on the question shows a better willingness to investigate and do some digging - and therefore invite some suggestions to help with this. The drive is detected by Windows 7 (i.e. speech bubble "network drive found") but on trying to open an Explorer window, this remains blank with the Windows busy pointer. I'd prefer not to reinstall Windows 7 to see if that cures the problem, I'd rather understand what is happening/not happening, perhaps even compare differences with Windows XP. Suggestions, please for such guides or even the original problem itself. Update Edit Rewrote question more comprehensively here: Mhttp://superuser.com/questions/304209/looking-for-definitive-answer-to-accessing-a-network-share-via-windows-7-home-and

  Read the article

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• What Logs / Process Stats to monitor on a Ubuntu FTP server?

  - by Adam Salkin

  I am administering a server with Ubuntu Server which is running pureFTP. So far all is well, but I would like to know what I should be monitoring so that I can spot any potential stability and security issues. I'm not looking for sophisticated software, more an idea of what logs and process statistics are most useful for checking on the health of the system. I'm thinking that I can look at various parameters output from the "ps" command and compare to see if I have things like memory leaks. But I would like to know what experienced admins do. Also, how do I do a disk check so that when I reboot, I don't get a message saying something like "disk not checked for x days, forcing check" which delays the reboot? I assume there is command that I can run as a cron job late at night. How often should it be run? What things should I be looking at to spot intrusion attempts? The only shell access is SSH on a non-standard port through UFW firewall, and I regularly do a grep on auth.log for "Fail" or "Invalid". Is there anything else I should look at? I was logging the firewall (UFW) but I have very few open ports (FTP and SSH on a non standard port) so looking at lists of IP's that have been blocked did not seem useful. Many thanks

  Read the article

• Physical Debian to VMWare: vmware-converter, dd-image or otherwise?

  - by Dabu

  we have two debian Lenny production machines, both running larger commercial websites. Now these machines need to be moved, and in the process, they need to be virtualized to VMWare ESX. If you believe the internet information, there are several ways to accomplish this. The easiest for us would be to use our weekly dd backup where the whole disk, however, I have no experience with this kind of technology and if it is really possible. The second best way would be via an application on the source machine virtualizing it and generating an ESX compatible VM. However, the software is beta and unsupported, and after installation, nothing really works (the /etc/init.d/vmware-converter script doesn't actually do anything, start and stop reply with success messages, yet ps shows that there are no new processes). The worst way with the most work would be to install a new machine and set it up manually, copying files and databases as needed. This part is clear in it's execution, and my question(s) do not touch this. Is my 1st way possible? Has anyone done this yet, or better, has a page with instructions? Or is there a help page that explains how to correctly install, run and use the vmware-converter tool using a Debian installation (it's possible that I dod something wrong during installation already)? Thank you.

  Read the article

• Remote reboot of windows to knoppix

  - by user64452

  I am attempting to develop an Auditing application. This audit application will be employed on windows networks. The Audit will need to discover Hardware and software details of all machines attached to the network (including Printers) I do not want to have to install this application on each workstation. The audit app. needs to discover all the ip addresses of all the networked workstations. I have been prototyping this app for the last couple of months and have decided to try a new tack Is this possible? a). You have a windows network, min Windows XP sp3 and upwards b). Maximum of 100 Networked machines (if that matters) c). I need to remotely reboot each WINDOWS machine in turn on the entire network and get it to startup using UNIX, say knoppix for example! d). however the knoppix live cd is only available from one of the networked machines Questions... Morphology? Longevity? Incept dates? Cheers DD

  Read the article

• How to recover Windows Password without reinstalling if you forgot Windows password?

  - by user38908

  Usually, we can recover Windows admin password in two traditional ways. The first is to change Windows password with another admin account; the second is to recover the previous password with the windows password reset disk that had been created before you forgot the password. Take Windows XP for example, 1 At the Windows XP login prompt when the password is entered incorrectly click the reset button in the login failed window. 2 Insert the password reset diskette into the computer and click Next. 3 If the correct diskette Windows XP will open a window prompting for the new password you wish to use. However, we offen ignore the important of security until we have been locked out of computer. Fortunately, there is still the last way that can unlock your computer without reinstalling - erase Windows password with Windows password reset CD, which can recover admin password for Windows 7/XP/Vista/NT/2000/2003.... Take Windows Password unlocker for example, followings are the steps to create the reset CD 1.Download Windows Password Unlocker from Password Unlocker Official site 2.Decompress the Windows password unlocker and note that there is an .ISO image file. Burn the image file onto an blank CD with the burner freely supported by Password Unlocker. 3.Insert the newly created CD into the locked computer and re-boot it from the CD drive. 4.After launched the CD, a window pop up with all your account names(if you have several accounts) select one of the accounts that you have forgotten its password to reset it. Just one press, this software can remove Windows password instantly.

  Read the article

• Arduino IDE "launch 4j" error

  - by John

  I have a computer running Windows XP. I am trying to run the Arduino IDE 0022. I double-click on arduino.exe, it waits about 30 seconds on the load up title screen, and then it gives me this error: Launch 4j: an error occurred while starting the application My only choice is to click "OK"; the error goes away, and the Arduino IDE closes. If I try to delete the Arduino files (to try overwriting with some different files), I get an error that doesn't allow me to do so: Cannot delete awt.dll: Access denied Make sure the disk is not full or write protected and that the file is not currently in use. The only way to delete the file is by restarting the computer. So something must still be trying to run after that first error. I have noticed in Task Manager that some Java programs are still running: javaw.exe (3 processes) I think this is a problem with Java, but I checked and updated all of my Java software and it is all up to date. I have looked on other forums for this issue and none of them seemed to help. From the forums I have tried: Different Arduino IDE versions Updating Java Opening arduino.exe as Administrator Nothing has worked. Anyone have any suggestions?

  Read the article

• Use cell formatting (e.g. "Good", "Bad", "Neutral") in formulas?

  - by ngm

  I am compiling a comparison of different pieces of software in an Excel spreadsheet. It is a big long list of features (the rows), with each column being one of the applications I'm evaluating. I've used styles to visually show how well each product meets each feature, as well as the importance of that feature, and now I'm wondering if there's a way I can use those annotations in a formula. The table is like: . | Product A | Product B | Product C Feature A | blah blah blah Feature B | blah blah blah Feature C | blah blah blah .... | .... | etc | Where I've put 'blah' in the table above, in my actual spreadsheet is (potentially lengthy) descriptive text explaining something about this feature in the given product. I've then used the styles "Good", "Neutral" and "Bad" to visually annotate the description, to show how well each product meets that feature. For each feature I've also used the styles Accent4, 60% Accent4, 40% Accent4, etc, to annotate the importance of each feature. Now I'm wondering if somehow I can use those styles (the annotations) to tot up a total score for each product. e.g., Score for feature A = valueof(60% Accent4) * valueof(Good) Is it possible at all?

  Read the article

• Almost All Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

  Read the article

• Should I buy more RAM for my computer or a better CPU?

  - by Reijer The Coder

  I have recently bought a new laptop, an ASUS N56VJ-S4149H. I bought it to use it in all possible ways I could want, so that would be gaming downloading and streaming movies browsing the web and programming software. So far it has been running great but one thing annoys me a little bit. I frequently play Mount&Blade: Warband, it's a great game and you should check it out. Everything runs smoothly but only when I turn down the 'Texture Detail'. Otherwise it will lag a lot and I can't really play. Now my question is: Is this a problem of not enough RAM? At first I was really sure it was but after thinking about for a while I'm not anymore. My computer only has 4 Gigabytes of RAM and there is still a slot open. So will it improve when I buy another 8 Gigabytes? EDIT: It has an Nvidia GeForce GT 635M inside. and an Intel Core i5 3230M CPU with 2,6 GHz. Help and answers are really appreciated. Thanks to all.

  Read the article

< Previous Page | 977 978 979 980 981 982 983 984 985 986 987 988  | Next Page >