Search Results

Search found 25727 results on 1030 pages for 'solution'.

Page 985/1030 | < Previous Page | 981 982 983 984 985 986 987 988 989 990 991 992  | Next Page >

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• ScriptAlias makes requests match too many Location blocks. What is going on?

  - by brain99

  We wish to restrict access on our development server to those users who have a valid SSL Client certificate. We are running Apache 2.2.16 on Debian 6. However, for some sections (mainly git-http, setup with gitolite on https://my.server/git/) we need an exception since many git clients don't support SSL client certificates. I have succeeded in requiring client cert authentication for the server, and in adding exceptions for some locations. However, it seems this does not work for git. The current setup is as follows: SSLCACertificateFile ssl-certs/client-ca-certs.crt <Location /> SSLVerifyClient require SSLVerifyDepth 2 </Location> # this works <Location /foo> SSLVerifyClient none </Location> # this does not <Location /git> SSLVerifyClient none </Location> I have also tried an alternative solution, with the same results: # require authentication everywhere except /git and /foo <LocationMatch "^/(?!git|foo)"> SSLVerifyClient require SSLVerifyDepth 2 </LocationMatch> In both these cases, a user without client certificate can perfectly access my.server/foo/, but not my.server/git/ (access is refused because no valid client certificate is given). If I disable SSL client certificate authentication completely, my.server/git/ works ok. The ScriptAlias problem Gitolite is setup using the ScriptAlias directive. I have found that the problem occurs with any similar ScriptAlias: # Gitolite ScriptAlias /git/ /path/to/gitolite-shell/ ScriptAlias /gitmob/ /path/to/gitolite-shell/ # My test ScriptAlias /test/ /path/to/test/script/ Note that /path/to/test/script is a file, not a directory, the same goes for /path/to/gitolite-shell/ My test script simply prints out the environment, super simple: #!/usr/bin/perl print "Content-type:text/plain\n\n"; print "TEST\n"; @keys = sort(keys %ENV); foreach (@keys) { print "$_ => $ENV{$_}\n"; } It seems that if I go to https://my.server/test/someLocation, that any SSLVerifyClient directives are being applied which are in Location blocks that match /test/someLocation or just /someLocation. If I have the following config: <LocationMatch "^/f"> SSLVerifyClient require SSLVerifyDepth 2 </LocationMatch> Then, the following URL requires a client certificate: https://my.server/test/foo. However, the following URL does not: https://my.server/test/somethingElse/foo Note that this only seems to apply for SSL configuration. The following has no effect whatsoever on https://my.server/test/foo: <LocationMatch "^/f"> Order allow,deny Deny from all </LocationMatch> However, it does block access to https://my.server/foo. This presents a major problem for cases where I have some project running at https://my.server/project (which has to require SSL client certificate authorization), and there is a git repository for that project at https://my.server/git/project which cannot require a SSL client certificate. Since the /git/project URL also gets matched agains /project Location blocks, such a configuration seems impossible given my current findings. Question: Why is this happening, and how do I solve my problem? In the end, I want to require SSL Client certificate authorization for the whole server except for /git and /someLocation, with as minimal configuration as possible (so I don't have to modify the configuration each time something new is deployed or a new git repository is added). Note: I rewrote my question (instead of just adding more updates at the bottom) to take into account my new findings and hopefully make this more clear.

  Read the article

• Email forwarding from my domain to gmail - FAIL

  - by pitosalas

  [There are numerous similar questions on ServerFault but I couldn't find one that was exactly on point] Background: I use Gmail for my email client. My email is [email protected]. However the email that people communicate to me with is [email protected]. I run the server that hosts www.example.com and other domains, at ServerBeach. Up to yesterday, I had SENDMAIL painlessly just forward emails to [email protected] to [email protected] and everything was fine, for several years in fact. Suddenly my email stopped working - that is, my gmail account stopped receiving emails via the forward from my server. Looking into it I found a bunch of emails sitting on my server with content like this: ... while talking to gmail-smtp-in.l.google.com.: RCPT To: <<< 450-4.2.1 The user you are trying to contact is receiving mail at a rate that <<< 450-4.2.1 prevents additional messages from being delivered. Please resend your <<< 450-4.2.1 message at a later time. If the user is able to receive mail at that <<< 450-4.2.1 time, your message will be delivered. For more information, please <<< 450 4.2.1 visit xxxxxx://mail.google.com/support/bin/answer.py?answer=6592 u15si37138086qco.76 [email protected]... Deferred: 450-4.2.1 The user you are trying to contact is receiving mail at a rate that DATA <<< 550-5.7.1 [64.34.168.137 1] Our system has detected an unusual rate of <<< 550-5.7.1 unsolicited mail originating from your IP address. To protect our <<< 550-5.7.1 users from spam, mail sent from your IP address has been blocked. <<< 550-5.7.1 Please visit xxxxx://www.google.com/mail/help/bulk_mail.html to review <<< 550 5.7.1 our Bulk Email Senders Guidelines. u15si37138086qco.76 554 5.0.0 Service unavailable ... while talking to alt1.gmail-smtp-in.l.google.com.: From what I've been researching, I think somehow someone has/is hijacking my domain name or something and this somehow has caused gmail's servers to notice and cut me off. But I don't know really what's going on nor do I see whatever emails might be involved. I've read stuff on zoneedit.com that sounds like they might have a solution in their service for what I am trying to do. I also read a lot about admining DNS and SENDMAIL and tried various things, but nothing works. Can you tell from my description what is going on that caused GMail's server to stop accepting email from my server and is there a way to stop it? What is the 'correct' way to configure things so that emails to [email protected] behave as if they were sent to [email protected]? Thanks so much!

  Read the article

• Hardware recommendations / parts list for a modern, quiet ZFS NAS box - 2011-Feb edition [closed]

  - by dandv

  I want to build some really reliable storage for my data, and it seems that ZFS is the only filesystem at the moment that does live checksumming. That rules out DroboPro, so I'm looking to building a quiet ZFS NAS that would start with 4 2TB or larger hard drives. I'd like this system to be very reliable and relatively future-proof for 2-3 years, so I'm willing to invest some $$$ and buy higher end components. I did see questions here and on other forums about low-cost servers, but I'm not looking for those. I'd be super happy to go for an off-the-shelf solution, but I haven't found one that's quiet. I started doing the research (summarized on my wiki), but I realized that it just gets too complicated for what I know as a software dude, and I'm entering the analysis paralysis area. At this point, I'm basically looking for a parts list for a configuration that will work (and is modern), and I know there are folks around here who are way more competent than me. I've built computers and am comfortable assembling one and messing with *nix; I can follow guides; I just want to end the decision process for the hardware and software configuration. What I've researched so far (not that these are very modern components): Case: I think I've settled on the Antec Twelve Hundred case because it cools well, is quiet, and simply has 12 bays that allow elastic mounting. The SilverStone Raven is its counter-candidate, but I find its construction quite odd. For the PSU, I'm torn between Antec CP-850 and Nexus RX-8500, but I did this research more than a year ago. The Nexus has a very uniform power profile, and I'd rather not have the Antec spin up and down based on load. On the other hand, I'm not sure how often my file server will draw more than 400W under use. For the hard drives, I've read that WD Black drives are actually WD RE3 with a software setting changed. I'd also like to buy different drive types, not just 4 WDs. Recommendations? Right now I have a 2TB Hitachi Deskstar 7K300. For the motherboard, CPU and RAM I have no idea, other than the RAM must be ECC. I already asked a question here about ECC RAM, but I was misguided and was looking for a motherboard that would support USB 3.0 as well. I've learned to go with eSATA, or worry about USB later. Then there's the (liquid) cooling, Wi-Fi card, and FreeBSD vs. OpenSolaris Express. Lastly, I'm wondering if I can make this PC into a media server by adding a Blu-ray drive and a good sound card. But support for Blu-Ray is spotty on Linux, and I don't know if Windows 7 on VirtualBox would get sufficient hardware access to output HDMI or SPDIFF signals. (Running OpenSolaris virtualized is not an option because of the reliability risk.) Then there are HDCP concerns. Suggestions on that would be appreciated as well, but I don't want us to get sidetracked. A specific shopping list on the core components would be great, so I can start ordering, and in the meantime educate myself with regards to the other issues. Finally, I think this could become a great FAQ for those technically inclined to build their own ZFS server, but confused by the dizzying array of options out there, and I promise to compile the results and share my experience building and benchmarking the server.

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• iptables 1.4 and passive FTP on custom port

  - by Cracky

  after the upgrade from debian squeeze to wheezy I've got a problem with passive FTP connection. I could narrow it to be iptables related, as I could connect via FTP w/o problems after adding my IP to the iptables ACCEPT rule. Before the upgrade I was able just to do modprobe nf_conntract_ftp ports=21332 and adding iptables -A THRU -p tcp --dport 21332 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT now..it doesn't help anymore. The INPUT rule is being triggered as I can see in the counter, but the directory listing is the last thing it does. Setting up a passive-port range is the last thing I want to do, I dislike open ports. I also tried the trick with helper mod by adding following rule before the actual rule for 21332 iptables -A THRU -p tcp -i eth0 --dport 21332 -m state --state NEW -m helper --helper ftp-21332 -j ACCEPT but it doesn't help and is even not being triggered according to counter. The rule in the next line (w/o helper) is being triggered.. here some info: # iptables --version iptables v1.4.14 # lsmod |grep nf_ nf_nat_ftp 12460 0 nf_nat 18242 1 nf_nat_ftp nf_conntrack_ftp 12605 1 nf_nat_ftp nf_conntrack_ipv4 14078 32 nf_nat nf_defrag_ipv4 12483 1 nf_conntrack_ipv4 nf_conntrack 52720 7 xt_state,nf_conntrack_ipv4,xt_conntrack,nf_conntrack_ftp,nf_nat,nf_nat_ftp,xt_helper # uname -a Linux loki 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux # iptables-save # Generated by iptables-save v1.4.14 on Sun Jun 30 03:54:28 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :BLACKLIST - [0:0] :LOGDROP - [0:0] :SPAM - [0:0] :THRU - [0:0] :WEB - [0:0] :fail2ban-dovecot-pop3imap - [0:0] :fail2ban-pureftpd - [0:0] :fail2ban-ssh - [0:0] -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -p tcp -m multiport --dports 21,21332 -j fail2ban-pureftpd -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -p tcp -m multiport --dports 110,995,143,993 -j fail2ban-dovecot-pop3imap -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,SYN FIN,SYN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags SYN,RST SYN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,RST FIN,RST -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags FIN,ACK FIN -j DROP -A INPUT -i eth0 -p tcp -m tcp --tcp-flags ACK,URG URG -j DROP -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT -A INPUT -j BLACKLIST -A INPUT -j THRU -A INPUT -j LOGDROP -A OUTPUT -j ACCEPT -A OUTPUT -s 93.223.38.223/32 -j ACCEPT -A BLACKLIST -s 38.113.165.0/24 -j LOGDROP -A BLACKLIST -s 202.177.216.0/24 -j LOGDROP -A BLACKLIST -s 130.117.190.0/24 -j LOGDROP -A BLACKLIST -s 117.79.92.0/24 -j LOGDROP -A BLACKLIST -s 72.47.228.0/24 -j LOGDROP -A BLACKLIST -s 195.200.70.0/24 -j LOGDROP -A BLACKLIST -s 195.200.71.0/24 -j LOGDROP -A LOGDROP -m limit --limit 5/sec -j LOG --log-prefix drop_packet_ --log-level 7 -A LOGDROP -p tcp -m tcp --dport 25 -m limit --limit 2/sec -j LOG --log-prefix spam_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 80 -m limit --limit 2/sec -j LOG --log-prefix web_blacklist --log-level 7 -A LOGDROP -p tcp -m tcp --dport 22 -m limit --limit 2/sec -j LOG --log-prefix ssh_blacklist --log-level 7 -A LOGDROP -j REJECT --reject-with icmp-host-prohibited -A THRU -p icmp -m limit --limit 1/sec -m icmp --icmp-type 8 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 25 -j ACCEPT -A THRU -i eth0 -p udp -m udp --dport 53 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 110 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 143 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 465 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 585 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 993 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 995 -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 2008 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 10011 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 21332 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A THRU -i eth0 -p tcp -m tcp --dport 30033 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-dovecot-pop3imap -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-pureftpd -j RETURN -A fail2ban-ssh -j RETURN -A fail2ban-ssh -j RETURN COMMIT # Completed on Sun Jun 30 03:54:28 2013 So, as I said, I have no problems with connecting when adding my IP to go through..but that's not a solution as noone except me can connect anymore~ If someone got an idea what the problem is, please help me! Thanks Cracky

  Read the article

• Capistrano + Nginx + Passenger = 403

  - by slimchrisp

  I asked this over at stackoverflow as well, but still haven't received any answers that have helped me to solve this problem. I have spent almost a week at this point trying to solve the issue, and I'm just not making any headway. It seems that this issue is pretty common, but none of the solutions I found online work for me. A buddy of mine is actually creating the same setup, and he is having the same issue. After a few days stuck with the 403 error I started over using this tutorial: http://blog.ninjahideout.com/posts/a-guide-to-a-nginx-passenger-and-rvm-server I had hoped starting from scratch using this tutorial would work, but no dice. Either way, if you view the tutorial you can see what steps I have taken. Here is essentially what I have going on. I have a VPS account on linode.com Server OS is Ubuntu 10.04 Local OS (shouldn't matter, but just so you know) used to deploy with Capistrano is Snow Leopard 10.6.6 I use RVM on the server. Version is 1.2.2 I was previously on ruby-1.9.2-p0 [ i386 ], but per the tutorial listed above I switched to ree-1.8.7-2010.02 [ i386 ]. Running 'which ruby' from the command line verifies that I am using 1.8.7 with the following output: /usr/local/rvm/rubies/ree-1.8.7-2010.02/bin/ruby passenger -v prints the following: Phusion Passenger version 3.0.2 Running 'nginx -v' gives me a message that the command nginx could not be found. The server is definitely there and running as I can use nginx to serve static files, but this could have something to do with my problem. I have two users dealing with the install. root which I used to install everything, and deployer which is a user I created specifically to for deploying my applications My web app directory is in the deployer user's home directory as follows: /home/deployer/webapps/mysite.com/public Per Capistrano default deploy, a symbolic link called current is created in the public folder, and points to /home/deployer/webapps/mysite.com/public/releases/most_current_release I have chmodded the deployer directory recursively to 777 /opt/nginx permissions: rwxr-xr-x /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2 permissions: rwxrwsrwx My nginx config file has gone through just short of eternity variations, but currently looks like this: ================================================================================== worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/local/rvm/gems/ree-1.8.7-2010.02/gems/passenger-3.0.2; passenger_ruby /usr/local/rvm/bin/passenger_ruby; include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; server { # listen *:80; server_name mysite.com www.mysite.com; root /home/deployer/webapps/mysite.com/public/current; passenger_enabled on; passenger_friendly_error_pages on; access_log logs/mysite.com/server.log; error_log logs/mysite.com/error.log info; error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } } ================================================================================== I bounce nginx, hit the site, and boom. 403, and logs say directory index of /home/deployer... is forbidden As others with a similar problem have said, you can drop an index.html into the public/releases/current_release and it will render. But rails no worky. That's basically it. At this point I have just about completely exhausted every possible solution attempt I can think of. I am a programmer and definitely not a sysadmin, so I am 99% sure this has something to do with permissions that I have hosed, but for the life of me I just can't figure out where. If anyone can help I would really really appreciate it. If there's any specific permission things you want me to check (ie groups/permissions), can you please include the commands to do so as well. Hopefully this will help others in the future who read this post. Let me know if there is any other information I can provide, and thanks in advance!!!

  Read the article

• Lustre - issues with simple setup

  - by ethrbunny

  Issue: I'm trying to assess the (possible) use of Lustre for our group. To this end I've been trying to create a simple system to explore the nuances. I can't seem to get past the 'llmount.sh' test with any degree of success. What I've done: Each system (throwaway PCs with 70Gb HD, 2Gb RAM) is formatted with CentOS 6.2. I then update everything and install the Lustre kernel from downloads.whamcloud.com and add on the various (appropriate) lustre and e2fs RPM files. Systems are rebooted and tested with 'llmount.sh' (and then cleared with 'llmountcleanup.sh'). All is well to this point. First I create an MDS/MDT system via: /usr/sbin/mkfs.lustre --mgs --mdt --fsname=lustre --device-size=200000 --param sys.timeout=20 --mountfsoptions=errors=remount-ro,user_xattr,acl --param lov.stripesize=1048576 --param lov.stripecount=0 --param mdt.identity_upcall=/usr/sbin/l_getidentity --backfstype ldiskfs --reformat /tmp/lustre-mdt1 and then mkdir -p /mnt/mds1 mount -t lustre -o loop,user_xattr,acl /tmp/lustre-mdt1 /mnt/mds1 Next I take 3 systems and create a 2Gb loop mount via: /usr/sbin/mkfs.lustre --ost --fsname=lustre --device-size=200000 --param sys.timeout=20 --mgsnode=lustre_MDS0@tcp --backfstype ldiskfs --reformat /tmp/lustre-ost1 mkdir -p /mnt/ost1 mount -t lustre -o loop /tmp/lustre-ost1 /mnt/ost1 The logs on the MDT box show the OSS boxes connecting up. All appears ok. Last I create a client and attach to the MDT box: mkdir -p /mnt/lustre mount -t lustre -o user_xattr,acl,flock luster_MDS0@tcp:/lustre /mnt/lustre Again, the log on the MDT box shows the client connection. Appears to be successful. Here's where the issues (appear to) start. If I do a 'df -h' on the client it hangs after showing the system drives. If I attempt to create files (via 'dd') on the lustre mount the session hangs and the job can't be killed. Rebooting the client is the only solution. If I do a 'lctl dl' from the client it shows that only 2/3 OST boxes are found and 'UP'. [root@lfsclient0 etc]# lctl dl 0 UP mgc MGC10.127.24.42@tcp 282d249f-fcb2-b90f-8c4e-2f1415485410 5 1 UP lov lustre-clilov-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 2 UP lmv lustre-clilmv-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 4 3 UP mdc lustre-MDT0000-mdc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 4 UP osc lustre-OST0000-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 5 UP osc lustre-OST0003-osc-ffff880037e4d400 00fc176e-3156-0490-44e1-da911be9f9df 5 Doing a 'lfs df' from the client shows: [root@lfsclient0 etc]# lfs df UUID 1K-blocks Used Available Use% Mounted on lustre-MDT0000_UUID 149944 16900 123044 12% /mnt/lustre[MDT:0] OST0000 : inactive device OST0001 : Resource temporarily unavailable OST0002 : Resource temporarily unavailable lustre-OST0003_UUID 187464 24764 152636 14% /mnt/lustre[OST:3] filesystem summary: 187464 24764 152636 14% /mnt/lustre Given that each OSS box has a 2Gb (loop) mount I would expect to see this reflected in available size. There are no errors on the MDS/MDT box to indicate that multiple OSS/OST boxes have been lost. EDIT: each system has all other systems defined in /etc/hosts and entries in iptables to provide access. SO: I'm clearly making several mistakes. Any pointers as to where to start correcting them?

  Read the article

• Tomcat and ASP site under IIS6 with SSL

  - by Rafe

  I've been working on migrating our companies' website from it's original server to a new one and am having two different but possibly related problems. The box this is sitting on is a Windows 2003 server x64 running IIS 6. The Tomcat version is 5.5.x as it was the version the original deployment was built on. There are two other sites on the server one in plain HTML, another in PHP and the one I am trying to migrate is a combination of Java and ASP (the introductory/sign in pages being Java as well as many reports used for our clients and the administration pages being in ASP) First of all I can only access the site if I enter the ip followed by :8080 (xxx.xxx.xxx.xxx:8080). The original setup had an index.html file in the root of the site with a bit of javascript in the header that pointed the site to 'www.mysite.com/app/public' but if I try going directly to the site without the 8080 I get a 'page not found error' and the javascript redirector causes the same problem because it doesn't add the 8080 into the URL even though on the original site the 8080 wasn't present so I don't understand why it would need it now. The js redirect looks like this: <script language="JavaScript"> <!-- location.href = "/app/public/" location.replace("/app/public/"); //--> </script> When setting the site up I used the command line to unbind IIS from all of the ip's on the system (there are 12 ip's on this box) because I was led to believe Tomcat wanted to use localhost which wasn't accessible. I'm not sure if this was the right thing to do but I'm throwing it in for the sake of completeness. And actually, at this point trying to go to localhost from the server itself throws up a 'could not connect to localhost' error. If I go to localhost:8080 I get the tomcat welcome page. If I do localhost:8080/app/public I get the intro page to our website. So I'm not sure what I'm even looking at in this case, that is what the proper behavior should be. The second part of the problem is that if I do go to either the ip or localhost such as above (localhost:8080/app/public) and click on our login link it is supposed to transfer me to our login page yet instead I receive a 'could not connect' error and the url has changed to localhost:8443/app/secure. From my research I see that port 8443 is Tomcats SSL port and the server.xml alludes to it as follows: <Connector port="8080" maxHttpHeaderSize="8192" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" /> I have an SSL certificate assigned to the site via IIS and was under the impression that by default Tomcat allowed IIS to handle secure connections but apparently something is munged because it's not working. There is another section in the server.xml that reads like this: <Connector port="8009" enableLookups="false" redirectPort="443" protocol="AJP/1.3" /> Which I'm not sure what it is for although port 443 is the SSL port that IIS uses so I'm confused as to what this is supposed to be doing. Another question I have is when does the isap_redirector actually come into play? How does it know when to try and serve pages through Tomcat and when not to? I've hunted around the 'net for an answer and have yet to find a clear dialogue on the subject. Anyone have any pointers as to where to look for a solution to all of this?

  Read the article

• Problem installing build-essential and upgrading g++ on Ubuntu 8.04

  - by ehsanul

  I'm having some trouble with dependencies it seems, but myself don't really know how to resolve the issue. Here's the output: ~:) sudo apt-get install build-essential Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. Since you only requested a single operation it is extremely likely that the package is simply not installable and a bug report against that package should be filed. The following information may help to resolve the situation: The following packages have unmet dependencies: build-essential: Depends: g++ (>= 4:4.3.1) but 4:4.2.3-1ubuntu6 is to be installed E: Broken packages ~:) sudo apt-get install g++ Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. Since you only requested a single operation it is extremely likely that the package is simply not installable and a bug report against that package should be filed. The following information may help to resolve the situation: The following packages have unmet dependencies: g++: Depends: cpp (>= 4:4.3.1-1ubuntu2) but 4:4.2.3-1ubuntu6 is to be installed Depends: gcc (>= 4:4.3.1-1ubuntu2) but 4:4.2.3-1ubuntu6 is to be installed Depends: g++-4.3 (>= 4.3.1-1) but it is not going to be installed Depends: gcc-4.3 (>= 4.3.1-1) but it is not installable E: Broken packages ~:) Edit: I just tried aptitude instead of apt-get, as suggested. Doesn't work, had other problems: ~:) sudo aptitude install build-essential [sudo] password for ehsanul: Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Building tag database... Done The following packages are BROKEN: g++ g++-4.3 libstdc++6-4.3-dev The following packages have been automatically kept back: dpkg-dev fakeroot libdns35 libisc35 linux-libc-dev patch The following NEW packages will be automatically installed: libgmp3c2 libmpfr1ldbl The following packages have been kept back: adobe-flashplugin bind9-host dnsutils gvfs gvfs-backends gvfs-fuse libatm1 libbind9-30 libgvfscommon0 libisccc30 libisccfg30 liblwres30 libnautilus-extension1 linux-headers-2.6.24-24 linux-headers-2.6.24-24-generic linux-image-2.6.24-24-generic nautilus nautilus-data The following NEW packages will be installed: libgmp3c2 libmpfr1ldbl The following packages will be upgraded: build-essential The following partially installed packages will be configured: timidity 2 packages upgraded, 4 newly installed, 0 to remove and 24 not upgraded. Need to get 775kB/6265kB of archives. After unpacking 20.3MB will be used. The following packages have unmet dependencies: libstdc++6-4.3-dev: Depends: gcc-4.3-base (= 4.3.2-1ubuntu11) which is a virtual package. Depends: libstdc++6 (>= 4.3.2-1ubuntu11) but 4.2.4-1ubuntu4 is installed. g++-4.3: Depends: gcc-4.3-base (= 4.3.2-1ubuntu11) which is a virtual package. Depends: gcc-4.3 (= 4.3.2-1ubuntu11) which is a virtual package. Depends: libc6 (>= 2.8~20080505) but 2.7-10ubuntu4 is installed. g++: Depends: cpp (>= 4:4.3.1-1ubuntu2) but 4:4.2.3-1ubuntu6 is installed. Depends: gcc (>= 4:4.3.1-1ubuntu2) but 4:4.2.3-1ubuntu6 is installed. Depends: gcc-4.3 (>= 4.3.1-1) which is a virtual package. Resolving dependencies... The following actions will resolve these dependencies: Keep the following packages at their current version: build-essential [11.3ubuntu1 (hardy, now)] g++ [4:4.2.3-1ubuntu6 (hardy-updates, now)] g++-4.3 [Not Installed] libstdc++6-4.3-dev [Not Installed] Score is -9852 Accept this solution? [Y/n/q/?]

  Read the article

• Can spliting an access database cause printer and reporting issues?

  - by leeand00

  We have a setup in which our users log into an access database using MS Access 2003 over an RDP connection. The user's login to their own machines first using a roaming profile. They then click an rdp connection file on the desktop and login to the remote server, via RDP, where they use MS Access as the shell; they don't have any access to any of explorer.exe features such as the start menu. The database they are logging into is more of an application, and provides functionality for entering data, querying data, and running reports via form based menus. It all worked pretty well until we split the database as it was nearing 2GBs in size. We moved out the payroll data into a separate partition, a database with the same name in a different folder, both of them on the server. Only two tables were moved into this new database partition, and they were re-linked as external tables in the new partition. Now while everything appears to be working fine data-wise after the split, there's a new issue when our users login via RDP and attempt to run reports: often the report will not display and instead the user sees an error about the click event of the form. At first I didn't even know it was printer-related, as we didn't really change anything related to the printers as far as I knew. Confused about the error, I talked to the guy who previously worked here and who was in charge of splitting the database, and he told me to tell the users to set their default printers (on their local machines, not on the server) to the "printer" Microsoft XPS Document Writer which isn't a physical printer at all. This allowed the user's to display their reports, but if they want to print out reports, they are required to go to the File menu and select Print, clicking the print icon on the toolbar takes them to a Save As... dialog as would be expected when using the Microsoft XPS Document Writer as your default printer. It's easy to tell if the user is having a problem because a quick mouseover of the printer icon will yield a tooltip of (none) when they cannot access their reports, and a tooltip of Microsoft XPS Document Writer when they can view the reports. If the user's printer is set to anything other than Microsoft XPS Document Writer as the default on their local machine, then (none) is always displayed when they rdp to the database. The RDP settings are setup to transfer the local printer to the server. Telling the users to do this to print has been more of a band-aid on the whole situation until we find a better solution and an explanation as to why splitting a database would prevent users from printing or even viewing access database reports. Which is why I'm here asking this question. Also of note all the printers on the network now show up on the server so that when the users do click File->Print to print their reports on a physical printer, they have to look through a huge list of printers to find theirs in the dropdown. So the little band-aid fix we have is not ideal. Previously, only the printers on the user's local machine displayed here, and not all the printers on the network. My co-worker seems to think this has something to do with permissions, I personally think it has to do with roaming profiles, and Group Policies which is what I've been reading up on. I really don't know how to fix this or how it is related to splitting the database.

  Read the article

• Make exact mp4 (H264) format for uploading to youtube

  - by WHITECOLOR

  With ffmpeg I'm converting video from mp3 and picture to upload it to youtube. After upload, conversion fails. Reasons are unknown. I believe the problem is in format. By the way If I'm uploading file 5 minutes length, it fails if I upload 30 seconds of this file it succeeds. I have donwload mp4 file from youtube. Then I uploaded it, it is done very fast. So a nice solution would be to convert videos to the same format that is done by google. I got the following output by mpeg: ffmpeg version N-44264-g070b0e1 Copyright (c) 2000-2012 the FFmpeg developers built on Sep 7 2012 17:38:57 with gcc 4.7.1 (GCC) configuration: --enable-gpl --enable-version3 --disable-pthreads --enable-runt ime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass - -enable-libcelt --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-l ibfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenj peg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheo ra --enable-libutvideo --enable-libvo-aacenc --enable-libvo-amrwbenc --enable-li bvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --ena ble-zlib libavutil 51. 72.100 / 51. 72.100 libavcodec 54. 55.100 / 54. 55.100 libavformat 54. 25.105 / 54. 25.105 libavdevice 54. 2.100 / 54. 2.100 libavfilter 3. 16.100 / 3. 16.100 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 15.100 / 0. 15.100 libpostproc 52. 0.100 / 52. 0.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'youtubetrack0.mp4': Metadata: major_brand : mp42 minor_version : 0 compatible_brands: isommp42 creation_time : 2012-10-02 22:58:57 Duration: 00:06:46.66, start: 0.000000, bitrate: 176 kb/s Stream #0:0(und): Video: h264 (Constrained Baseline) (avc1 / 0x31637661), yu v420p, 450x360, 78 kb/s, 6 fps, 6 tbr, 12 tbn, 12 tbc Metadata: creation_time : 1970-01-01 00:00:00 handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 95 kb/s Metadata: creation_time : 2012-10-02 22:58:57 handler_name : IsoMedia File Produced by Google, 5-11-2011 Is it possible to construct ffmpeg parameters so that that would give the same format that google internally does? Is the information above sufficient? I couldn't construct needed params. For example I don't understand how to set tbn and what 95 kb/s mean in "Stream #0:1(und): Audio:". Now I just do: ffmpeg -i videoimage.jpg -i audio.mp3 video.mp4 Info I've got: ffmpeg version N-44998-gdf82454 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 2 2012 23:03:12 with gcc 4.7.1 (GCC) configuration: --disable-static --enable-shared --enable-gpl --enable-version3 --disable-pthreads --enable-runtime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libass --enable-libcelt --enable-libopencore-amrnb --en able-libopencore-amrwb --enable-libfreetype --enable-libgsm --enable-libmp3lame --enable-libnut --enable-libopenjpeg --enable-librtmp --enable-libschroedinger - -enable-libspeex --enable-libtheora --enable-libutvideo --enable-libvo-aacenc -- enable-libvo-amrwbenc --enable-libvorbis --enable-libvpx --enable-libx264 --enab le-libxavs --enable-libxvid --enable-zlib libavutil 51. 73.101 / 51. 73.101 libavcodec 54. 63.100 / 54. 63.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'video.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2avc1mp41 encoder : Lavf54.25.105 Duration: 00:06:46.81, start: 0.000000, bitrate: 129 kb/s Stream #0:0(und): Video: h264 (High) (avc1 / 0x31637661), yuvj420p, 450x360, 3392 kb/s, 25 fps, 25 tbr, 25 tbn, 50 tbc Metadata: handler_name : VideoHandler Stream #0:1(und): Audio: aac (mp4a / 0x6134706D), 44100 Hz, stereo, s16, 127 kb/s Metadata: handler_name : SoundHandler This video fails the conversion on youtube. I also tried to use other vcode parmam and extensions of output file (mp4, wmv, avi) but failed too. Would be greatful for help.

  Read the article

• Distributed and/or Parallel SSIS processing

  - by Jeff

  Background: Our company hosts SaaS DSS applications, where clients provide us data Daily and/or Weekly, which we process & merge into their existing database. During business hours, load in the servers are pretty minimal as it's mostly users running simple pre-defined queries via the website, or running drill-through reports that mostly hit the SSAS OLAP cube. I manage the IT Operations Team, and so far this has presented an interesting "scaling" issue for us. For our daily-refreshed clients, the server is only "busy" for about 4-6 hrs at night. For our weekly-refresh clients, the server is only "busy" for maybe 8-10 hrs per week! We've done our best to use some simple methods of distributing the load by spreading the daily clients evenly among the servers such that we're not trying to process daily clients back-to-back over night. But long-term this scaling strategy creates two notable issues. First, it's going to consume a pretty immense amount of hardware that sits idle for large periods of time. Second, it takes significant Production Support over-head to basically "schedule" the ETL such that they don't over-lap, and move clients/schedules around if they out-grow the resources on a particular server or allocated time-slot. As the title would imply, one option we've tried is running multiple SSIS packages in parallel, but in most cases this has yielded VERY inconsistent results. The most common failures are DTExec, SQL, and SSAS fighting for physical memory and throwing out-of-memory errors, and ETLs running 3,4,5x longer than expected. So from my practical experience thus far, it seems like running multiple ETL packages on the same hardware isn't a good idea, but I can't be the first person that doesn't want to scale multiple ETLs around manual scheduling, and sequential processing. One option we've considered is virtualizing the servers, which obviously doesn't give you any additional resources, but moves the resource contention onto the hypervisor, which (from my experience) seems to manage simultaneous CPU/RAM/Disk I/O a little more gracefully than letting DTExec, SQL, and SSAS battle it out within Windows. Question to the forum: So my question to the forum is, are we missing something obvious here? Are there tools out there that can help manage running multiple SSIS packages on the same hardware? Would it be more "efficient" in terms of parallel execution if instead of running DTExec, SQL, and SSAS same machine (with every machine running that configuration), we run in pairs of three machines with SSIS running on one machine, SQL on another, and SSAS on a third? Obviously that would only make sense if we could process more than the three ETL we were able to process on the machine independently. Another option we've considered is completely re-architecting our SSIS package to have one "master" package for all clients that attempts to intelligently chose a server based off how "busy" it already is in terms of CPU/Memory/Disk utilization, but that would be a herculean effort, and seems like we're trying to reinvent something that you would think someone would sell (although I haven't had any luck finding it). So in summary, are we missing an obvious solution for this, and does anyone know if any tools (for free or for purchase, doesn't matter) that facilitate running multiple SSIS ETL packages in parallel and on multiple servers? (What I would call a "queue & node based" system, but that's not an official term). Ultimately VMWare's Distributed Resource Scheduler addresses this as you simply run a consistent number of clients per VM that you know will never conflict scheduleing-wise, then leave it up to VMWare to move the VMs around to balance out hardware usage. I'm definitely not against using VMWare to do this, but since we're a 100% Microsoft app stack, it seems like -someone- out there would have solved this problem at the application layer instead of the hypervisor layer by checking on resource utilization at the OS, SQL, SSAS levels. I'm open to ANY discussion on this, and remember no suggestion is too crazy or radical! :-) Right now, VMWare is the only option we've found to get away from "manually" balancing our resources, so any suggestions that leave us on a pure Microsoft stack would be great. Thanks guys, Jeff

  Read the article

• Log transport and aggregation at scale

  - by markdrayton

  How're you analysing log files from UNIX/Linux machines? We run several hundred servers which all generate their own log files, either directly or through syslog. I'm looking for a decent solution to aggregate these and pick out important events. This problem breaks down into 3 components: 1) Message transport The classic way is to use syslog to log messages to a remote host. This works fine for applications that log into syslog but less useful for apps that write to a local file. Solutions for this might include having the application log into a FIFO connected to a program to send the message using syslog, or by writing something that will grep the local files and send the output to the central syslog host. However, if we go to the trouble of writing tools to get messages into syslog would we be better replacing the whole lot with something like Facebook's Scribe which offers more flexibility and reliability than syslog? 2) Message aggregation Log entries seem to fall into one of two types: per-host and per-service. Per-host messages are those which occur on one machine; think disk failures or suspicious logins. Per-service messages occur on most or all of the hosts running a service. For instance, we want to know when Apache finds an SSI error but we don't want the same error from 100 machines. In all cases we only want to see one of each type of message: we don't want 10 messages saying the same disk has failed, and we don't want a message each time a broken SSI is hit. One approach to solving this is to aggregate multiple messages of the same type into one on each host, send the messages to a central server and then aggregate messages of the same kind into one overall event. SER can do this but it's awkward to use. Even after a couple of days of fiddling I had only rudimentary aggregations working and had to constantly look up the logic SER uses to correlate events. It's powerful but tricky stuff: I need something which my colleagues can pick up and use in the shortest possible time. SER rules don't meet that requirement. 3) Generating alerts How do we tell our admins when something interesting happens? Mail the group inbox? Inject into Nagios? So, how're you solving this problem? I don't expect an answer on a plate; I can work out the details myself but some high-level discussion on what is surely a common problem would be great. At the moment we're using a mishmash of cron jobs, syslog and who knows what else to find events. This isn't extensible, maintainable or flexible and as such we miss a lot of stuff we shouldn't. Updated: we're already using Nagios for monitoring which is great for detected down hosts/testing services/etc but less useful for scraping log files. I know there are log plugins for Nagios but I'm interested in something more scalable and hierarchical than per-host alerts.

  Read the article

• Linux: Apple Wireless A1314 Fn key not registered, looks like software bug

  - by ramplank

  I'm trying to set up my Apple Wireless Keyboard with my Kubuntu systems. These are PC hardware powered by Intel Atom and Intel i5 respectively. The keyboard has a US keyboard layout and has model number A1314 written on the back. It takes two AA batteries. I'm saying that because it appears there are multiple types of model A1314. I have tried this on a 10.04, 11.04, 11.10 and 12.04 system with no success. Every time using a bluetooth dongle and the KDE bluetooth notification tray applet, the keyboard can be connected. In both cases it shows up as "Apple Wireless Keyboard". Almost everything works as expected, in fact, I'm typing on it right now. But one thing doesn't: The Fn key. I'd like to use Fn + Down Arrow as PgDn / Page Down, I understand this is default behaviour on Apple keyboards. And of course I'd like the same for Page Up, Home and End. I'll stick to Page Down in my example. I used the xev tool to see the keycodes the system receives, and if I press on Fn nothing happens, and nothing is registered. If I press Fn + Down Arrow, xev only registers the down arrow. Here's the output from my 11.04 system to illustrate: Press just the Fn key: no output Press Down Arrow key: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699773, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2699860, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False Press Fn+Down Arrow Keys together: KeyPress event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701548, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4400001, root 0x15d, subw 0x4400002, time 2701623, (44,45), root:(1352,298), state 0x10, keycode 116 (keysym 0xff54, Down), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False I've been searching this forum and other Linux-related forums for hours but I still have not found a solution. I mostly found advice on how to fix this when using an actual apple laptop or desktop, but I don't have that. They said to try something like the following echo 2 > /sys/module/hid_apple/ ... But since there's no hid_apple directory present on my systems, I've needed to modprobe hid_apple first. That didn't help either. I'm cool with changing some config files, or compiling my own patched kernel if that's necessary. I currently have a 10.04 and 12.04 system available to test. The same issue occurs when hooked up to Windows 7. Fn key still does nothing, not by itself or in combination with other keys. With some AutoHotkey fiddling, I was able to confirm the key is registered as pressed, but ignored by default. A custom AutoHotkey script can fix that. But AutoHotkey is only for Windows, I want my problem fixed on Linux. Hooked up to an iPad 2 it only works in combination with the F1-F12 keys. Not with the arrow keys. If the screen of the ipad is off, and I press just the Fn key, the screen will come on, so the key itself is registered as pressed. So to sum up my question: Can anyone help me get Page Up, Page Down, Home and End to work on this keyboard, when that requires me to use an Fn key which is currently not registered?

  Read the article

• Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

  - by Chris Drumgoole

  I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

  - by Jørgen

  I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

  Read the article

• SQL Server Log File Won't Shrink due cause "log are pending replication" on non replicated DB?

  - by user796466

  I have a non Mission Critial DB 9am-5pm SQL Server database that I have set up to do nightly full backups and log backups every 30 minutes during business hours. The database is in full recovery and normally I have no reason to truncate/shrink logs unless I do some heavy maintenance. Log backups manage the size with no issue. However I have not been at this client for several weeks and upon inspection I noticed that the log had grown to about 10 times the size of the .mdf file. I poked around backups had been running and I had not gotten any severity error alerts (SQL mail). I attempted to put DB in simple recovery and shrink the log, this was no good. I precede to try a log backup and I got: The log was not truncated because records at the beginning of the log are pending replication or Change Data Capture. Ensure the Log Reader Agent or capture job is running or use sp_repldone to mark transactions as distributed or captured. Restart SQL Server rinse repeat same thing ... I said ??? Replication is not nor ever has been set up on this DB or database /server ??? So the log backups have not been flushing the .ldf. So I did a couple hours of research and I found: http://www.sqlmonster.com/Uwe/Forum.aspx/sql-server/5445/Log-file-is-not-truncated-inspite-of-regular-log-backup http://www.eggheadcafe.com/software/aspnet/30708322/the-log-was-not-truncated-because-records-at-the-beginning-of-the-log-are-pending-replication.aspx seems to be some kind of poorly documented bug ?? The solution seems to have been to run exec sp_repldone, more precisley EXEC sp_repldone @xactid = NULL, @xact_segno = NULL, @numtrans = 0, @time= 0, @reset = 1 This procedure can be used in emergency situations to allow truncation of the transaction log when transactions pending replication are present. Using this procedure prevents Microsoft SQL Server 2000 from replicating the database until the database is unpublished and republished. ~ MSDN When I do that I get the following Msg 18757, Level 16, State 1, Procedure sp_repldone, Line 1 Unable to execute procedure. The database is not published. Execute the procedure in a database that is published for replication. Which makes sense Because the DB has never been published for replication. I have several questions: A) First and foremost is, WTF is going on ? What is causeing this, I am interested in knowing the why here ? Is this genuinley a bug or is there some aspect of the backup that is not functioning properly that cause's the DB to mimick a replicated state ? Someone please edify me on this. B) Second ... Do I really have to publish / replicate this DB to exec this SP to fix this ??? Sounds crazy or is there some T-SQL that I can put it in a published state exec the proc and be on my way ... C) Third, if I do indeed have to publish this database to exec the SP to release this unneeded mis replicated/intended log , to get my .ldf file and backup back on track. How do I publish the database without an online host that it is asking for ??? I don't generally do this kind of database administration and need some guidance. Sorry if this is too verbose but just voicing the question helps me clarify it ... Thank you in advance for your help

  Read the article

• Network update solutions for a company of ~20 (5 local, 15 remote)?

  - by Margaret

  Hi all This is probably going to be a bit up in the air, because we're still in the "reaching towards solutions" phase, but I figured I'd see what you guys had to say. Plus I honestly know very little about systems and what is good and bad pratice. My organisation has always more or less worked on the concept of local machines; since it primarily employed contractors who were working from home, each of those people was largely responsible for their own machine and backup procedures and the like. We're now expanding, though we're still reasonably small (we're up to about 20 staff members). Most people still work remotely, but we have a central office where about five people are working. But we're getting large enough that we're starting to think it would be a good idea to have a central file server, and things like that - if someone gets hit by a bus, we want someone else to know where to look for the files to continue their work. A lot of the people who work for us remotely work on projects for other companies as well, so I don't want to force them to log in to our server whenever they're on a network. But I do want to make connection to be as painless as possible to do so, to improve utilisation. The other thing is that we're getting more people who would like to remote into the office server and do their work there. Our current remote connection application is an SSH install that allows people access to the network; the problem is, it's a black box to me, and I've never understood how to even connect to it (despite supposedly being de facto sysadmin). Thus far I've been able to bounce questions about how to get it working to the guy who does know it well, but he's leaving the company soon. So we probably need a solution for this that I actually understand. We were knocking around the idea of implementing a VPN with some form of remote desktop, and someone mentioned that this was largely a matter of purchasing a router capable of it; I'm not sure of the truth of that statement. This is what we have in the office: Two shiny new i7 servers, each running Windows Server 2008. Precise eventual layout is still being debated, a little, but the current suggestion is that one is primary database crunching, while the other is a warm backup of the databases, along with running Reporting Services. They currently have SQL Server 2008 installed on them, which is being connected to via the 'sa' account. We're hoping to make each person use their own account (preferably one tied to the 'central' password we set up, so we can use Windows Authentication). An older server, running XP Pro, that we are currently using as a test bed for a project that requires access to older versions of software. This machine is also being used to take backups, but I'm thinking of moving that functionality elsewhere. A spare desktop from a guy who left the company (XP Pro). We're thinking of bumping up the hard disk space and using it as the magical file server that's going to solve one particular everything. Assorted desktops, laptops, etc, at least one for each person in the office (mix of Win XP and Win 7; occasionally a person who normally works remotely might drop in to the office and bring a laptop bearing Vista, but it's pretty rare). All are set up as local user accounts at the moment; I don't know if it's the best arrangement. Purchasing more hardware is not a big problem, but we figure we might as well make use of what we've got first. Is Active Directory a big magic wand that's going to solve all the world's problems? Is there some other arrangement we should be looking to instead?

  Read the article

• Exchange 2003 mail non-delivery (NDR), spam activity? events 7002 & 7004

  - by HighTechGeek

  Windows Server 2003 Small Business Server SP2 Exchange Version 6.5 (Build 7638.2: Service Pack 2) This network has been neglected and has been having email problems for years and was on many blacklists. I was called in after the server eventually crashed... I got the server back up and running, but email problems persist. Outgoing mail delivery is sporadic. Sometimes the mail goes through, sometimes a delayed delivery report is generated after a day or more, and sometimes it seems to go through, but the recipient never receives it. Not sure if spammers are successfully using the server as a relay (see event entries below after turning on maximum SMTP logging)... User PCs infected with viruses and server was blacklisted on many sites (I used mxtoolbox.com) I have cleaned all the PCs and changed all passwords (including administrator) I have requested removal from all of the blacklists - most have removed the listing, some take more time. I have setup rDNS pointer records with the ISP (Comcast) - that was one reason for some of the blacklistings. I have tested that it's not an open relay using telnet as described here: www.amset.info/exchange/smtp-openrelay.asp I followed the advise of a Spamhaus & Microsoft article to enable maximum SMTP logging. http://www.spamhaus.org/faq/answers.lasso?section=isp%20spam%20issues#320 which directed me to Microsoft KB article 895853, specifically, the part 2/3 down titled: "If mail relay occurs from an account on an Exchange computer that is not configured as an open relay" . The Application Event Log is filling with this type of activity (Event ID 7002, 7002 & 3018 errors): Event Type: Error Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7004 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol error log for virtual server ID 1, connection #621. The remote host "212.52.84.180", responded to the SMTP command "rcpt" with "550 #5.1.0 Address rejected [email protected] ". The full command sent was "RCPT TO: ". This will probably cause the connection to fail. and this: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 7:33:29 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #620. The remote host "212.52.84.170", responded to the SMTP command "rcpt" with "452 Too many recipients received this hour ". The full command sent was "RCPT TO: ". This may cause the connection to fail. or a variant of: Event Type: Warning Event Source: MSExchangeTransport Event Category: SMTP Protocol Event ID: 7002 Date: 1/18/2011 Time: 8:39:21 AM User: N/A Computer: SERVER Description: This is an SMTP protocol warning log for virtual server ID 1, connection #661. The remote host "82.57.200.133", responded to the SMTP command "rcpt" with "421 Service not available - too busy ". The full command sent was "RCPT TO: ". This may cause the connection to fail. also Event Type: Error Event Source: MSExchangeTransport Event Category: NDR Event ID: 3018 Date: 1/18/2011 Time: 9:49:37 AM User: N/A Computer: SERVER Description: A non-delivery report with a status code of 5.4.0 was generated for recipient rfc822;[email protected] (Message-ID ). Causes: This message indicates a DNS problem or an IP address configuration problem Solution: Check the DNS using nslookup or dnsq. Verify the IP address is in IPv4 literal format. Data: 0000: ef 02 04 c0 ï..À Any guidance and/or suggestions and/or tests to perform would be greatly appreciated.

  Read the article

• Windows 8 Stuck on Start Screen File Search

  - by baturayd

  I have been searching someone else having the same issue but I couldn't find any. Here is my problem: I'm using Windows 8 Pro with Media Center. File search screen does not close itself after I make a file search within start screen. It stuck on that screen. I can't go back to desktop, therefore, task manager is inaccessible. Only way to get out of it is to sign out. It also looks like non-operational. It doesn't give me any result at all. It's just a blank screen with "Files" title. It used to work perfectly. Things I have done before coming here: Safe mode minimal boot to ensure no other 3rd party software interferes. sfc haven't found any inconsistencies. Search index has been rebuild. Normal boot with all 3rd party services and start-up items disabled. System restore to a date that I know this feature was functional. And by the way, I have installed all updates released so far. I strongly used file search via start menu back in Windows 7. This is an absolute game changer for me. I'm curious what causes this. I'll do a "system refresh" if I can't fix this. I'm working on it, I'll keep this thread updated should I find any fix. First update: I just discovered that file search screen gets stuck if it's invoked by typing query directly in start screen. It doesn't get stuck if it's invoked from win + x menu. I was able to "escape" from stuck screen with invoking it again by win + x menu. After rebuilding search index again, search suggestions started to appear again but still there is no file search functionality. Second update: "Results for" expression appears only for a second near to "Files" title when search is initialized. Third update: As a last resort, I finally tried to do a "System Refresh" which has also failed to refresh by giving an error after waiting almost 20 minutes at 99%. (Seriously?) After cold boot it began to undo changes. After changes were reverted, I boot the machine without doing anything further and bingo! Search began acting normal again. This is a totally weird solution. It obviously fixed certain system files during failed refresh, and kept those changes untouched because they were supposed to be that way at the first place. I'll keep this thread alive should anyone comes with a more logical explanation. Forth update: After a windows update, search functionality again stopped responding. It happened after a system update for the first time. Now I have a pretty good suspicion about system update, though I have no solid proof of its involvement with this problem.

  Read the article

• Using jQuery and SPServices to Display List Items

  - by Bil Simser

  I had an interesting challenge recently that I turned to Marc Anderson’s wonderful SPServices project for. If you haven’t already seen or used SPServices, please do. It’s a jQuery library that does primarily two things. First, it wraps up all of the SharePoint web services in a nice little AJAX wrapper for use in JavaScript. Second, it enhances the form editing of items in SharePoint so you’re not hacking up your List Form pages. My challenge was simple but interesting. The user wanted to display a SharePoint item page (DispForm.aspx, which already had some customization on it to display related items via this blog post from Codeless Solutions for SharePoint) but launch from an external application using the value of one of the fields in the SharePoint list. For simplicity let’s say my list is a list of customers and the related list is a list of orders for that customer. It would look something like this (click on the item to see the full image): Your first thought might be, that’s easy! Display the customer information using a DataView Web Part and filter the item using a query string to match the customer number. However there are a few problems with this idea: You’ll need to build a custom page and then attach that related orders view to it. This is a bit of a problem because the solution from Codeless Solutions relies on the Title field on the page to be displayed. On a custom page you would have to recreate all of the elements found on the DispForm.aspx page so the related view would work. The DataView Web Part doesn’t look *exactly* like what the out of the box display form page does. Not a huge problem and can be overcome with some CSS style overrides but still, more work. A DVWP showing a single record doesn’t have the same toolbar that you would using the DispForm.aspx. Not a show-stopper and you can rebuild the toolbar but it’s going to potentially require code and then there’s the security trimming, etc. that you have to get right. DVWPs are not automatically updated if you add a column to the list like DispForm.aspx is. Work, work, work. For these reasons I thought it would be easier to take the already existing (modified) DispForm.aspx page and just add some jQuery magic to the page to find the item. Why do we need to find it? DispForm.aspx relies on a querystring parameter called “ID” which then displays whatever that item ID number is in the list. Trouble is, when you’re coming in from an external app via a link, you don’t know what that internal ID is (and frankly shouldn’t). I don’t like exposing internal SharePoint IDs to the outside world for the same reason I don’t do it with database IDs. They’re internal and while it’s find to use on the site itself you don’t want external links using it. It’s volatile and can change (delete one item then re-add it back with the same data and watch any ID references break). The next thought might be to call a SharePoint web service with a CAML query to get the item ID number using some criteria (in this case, the customer number). That’s great if you have that ability but again we had an existing application we were just adding a link to. The last thing I wanted to do was to crack open the code on that sucker and start calling web services (primarily because it’s Java, but really I’m a lazy geek). However if you’re doing this and have access to call a web service that would be an option. Back to this problem, how do I a) find a SharePoint List Item based on some field value other than ID and b) make it low impact so I can just construct a URL to it? That’s where jQuery and SPServices came to the rescue. After spending a few hours of emails back and forth with Marc and a couple of phone calls (and updating jQuery to the latest version, duh!) it was a simple answer. First we need a reference to a) jQuery b) SPServices and c) our script. I just dropped a Content Editor Web Part, the Swiss Army Knives of Web Parts, onto the DispForm.aspx page and added these lines: <script type="text/javascript" src="http://intranet/JavaScript/jquery-1.4.2.min.js"></script> <script type="text/javascript" src="http://intranet/JavaScript/jquery.SPServices-0.5.3.min.js"></script> <script type="text/javascript" src="http://intranet/JavaScript/RedirectToID.js"> </script> Update it to point to where you keep your scripts located. I prefer to keep them all in Document Libraries as I can make changes to them without having to remote into the server (and on a multiple web front end, that’s just a PITA), it provides me with version control of sorts, and it’s quick to add new plugins and scripts. Now we can look at our RedirectToID.js script. This invokes the SPServices Library to call the GetListItems method of the Lists web service and then rewrites the URL to DispForm.aspx to use the correct SharePoint ID (the internal one). $(document).ready(function(){ var queryStringValues = $().SPServices.SPGetQueryString(); var id = queryStringValues["ID"]; if(id == "0") { var customer = queryStringValues["CustomerNumber"]; var query = "<Query><Where><Eq><FieldRef Name='CustomerNumber'/><Value Type='Text'>" + customer + "</Value></Eq></Where></Query>"; var url = window.location; $().SPServices({ operation: "GetListItems", listName: "Customers", async: false, CAMLQuery: query, completefunc: function (xData, Status) { $(xData.responseXML).find("[nodeName=z:row]").each(function(){ id = $(this).attr("ows_ID"); url = $().SPServices.SPGetCurrentSite() + "/Lists/Customers/DispForm.aspx?ID=" + id; window.location = url; }); } }); } }); What’s happening here? Line 3: We call SPServices.SPGetQueryString to get an array of query string values (a handy function in the library as I had 15 lines of code to do this which is now gone). Line 4: Extract the ID value from the query string Line 6: If we pass in “0” it means we’re looking up a field value. This allows DispForm.aspx to work like normal with SharePoint lists but lookup our values when invoked. Why ID at all? DispForm.aspx doesn’t work unless you pass in something and “0” is a *magic* number that will invoke the page but not lookup a value in the database. Line 8-15: Extract the CustomerNumber query string value, build a CAML query to find it then call the GetListitems method using SPServices Line 16: Process the results in our completefunc to iterate over all the rows (there should only be one) and extract the real ID of the item Line 17-20: Build a new URL based on the site (using a call to SPGetCurrentSite) and append our real ID to redirect to the DispForm.aspx page As you can see, it dynamically creates a CAML query for the call to the web service using the passed in value. You could even make this generic to take in different query strings, one for the field name to search for and the other for the value to find. That way it could be used for any field you want. For example you could bring up the correct item on the DispForm.aspx page based on customer name with something like this: http://myserver/Lists/Customers/DispForm.aspx?ID=0&FilterId=CustomerName&FilterValue=Sony Use your imagination. Some people would opt for building a custom page with a DVWP but if you want to leverage all the functionality of DispForm.aspx this might come in handy if you don’t want to rely on internal SharePoint IDs.

  Read the article

• unmet dependencies in Ubuntu 12.04

  - by lee.O

  I tried today to install a dvb-card on my Ubuntu 12.04 (Linux blauhai-linux 3.2.0-25-generic #40-Ubuntu SMP Wed May 23 20:30:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ). The installation failed with an error. After that, i tried to install python (it was already installed but i got this error): linux:~$ sudo apt-get install git Reading package lists... Done Building dependency tree Reading state information... Done git is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: python-glade2:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python-support:i386 (= 0.3.4) but it is not installable Depends: python:i386 (= 2.4) but it is not going to be installed Depends: libglade2-0:i386 (= 1:2.5.1) but it is not going to be installed Depends: python-gtk2:i386 (= 2.8.6-8) but it is not going to be installed python-numeric:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python:i386 (= 2.3) but it is not going to be installed Depends: python-central:i386 (= 0.5.7) but it is not installable E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). well, i can read and tried the proposed command, but then i get this: linux:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libopenal1:i386 libsdl-ttf2.0-0:i386 libkrb5-3:i386 libgconf-2-4:i386 libsm-dev libatk1.0-0:i386 libk5crypto3:i386 libstdc++5:i386 libqt4-declarative:i386 libxcomposite1:i386 libice-dev libgail18:i386 libldap-2.4-2:i386 libao-common libv4l-0:i386 liblcms1:i386 libqt4-qt3support:i386 libroken18-heimdal:i386 libunistring0:i386 libcupsimage2:i386 libgphoto2-port0:i386 libidn11:i386 libnss3:i386 libcaca0:i386 gtk2-engines:i386 libgudev-1.0-0:i386 libjpeg-turbo8:i386 libpthread-stubs0 libcairo-gobject2:i386 libavc1394-0:i386 libjpeg8:i386 libotr2 libaio1:i386 libsane:i386 odbcinst1debian2 odbcinst1debian2:i386 libqt4-test:i386 libqt4-script:i386 libqt4-designer:i386 libsdl-mixer1.2:i386 libqt4-network:i386 libqt4-dbus:i386 libcap2:i386 libproxy1:i386 ibus-gtk:i386 libdbus-glib-1-2:i386 libtdb1:i386 libasn1-8-heimdal:i386 libspeex1:i386 libxslt1.1:i386 libgomp1:i386 libcapi20-3:i386 libibus-1.0-0:i386 libcairo2:i386 libgnutls26:i386 libopenal-data odbcinst libgssapi3-heimdal:i386 libcanberra0:i386 libtasn1-3:i386 libfreetype6:i386 x11proto-kb-dev gtk2-engines-murrine:i386 libwavpack1:i386 libqt4-opengl:i386 libsoup-gnome2.4-1:i386 libv4lconvert0:i386 gstreamer0.10-plugins-good:i386 libc6-i386 lib32gcc1 libqt4-xmlpatterns:i386 librsvg2-common:i386 libdatrie1:i386 xtrans-dev libavahi-common-data:i386 libiec61883-0:i386 lib32asound2 libgdk-pixbuf2.0-0:i386 libsdl-image1.2:i386 libp11-kit0:i386 x11proto-input-dev libwind0-heimdal:i386 libpixman-1-0:i386 libsdl1.2debian:i386 libxaw7:i386 libgdbm3:i386 libcups2:i386 libcurl3:i386 libqtcore4:i386 libxinerama1:i386 libesd0:i386 libmikmod2:i386 libkrb5support0:i386 libxft2:i386 libxt-dev libcroco3:i386 libpulse-mainloop-glib0:i386 libice6:i386 libaa1:i386 libieee1284-3:i386 libgcrypt11:i386 libthai0:i386 libao4:i386 libkeyutils1:i386 libxmu6:i386 libcanberra-gtk0:i386 libvorbisfile3:i386 libqt4-sql:i386 esound-common libxpm4:i386 libqt4-svg:i386 libusb-0.1-4:i386 libgail-common:i386 libxrender1:i386 libhcrypto4-heimdal:i386 libraw1394-11:i386 libnspr4:i386 libshout3:i386 libdv4:i386 libhx509-5-heimdal:i386 libxau-dev libqt4-xml:i386 gstreamer0.10-x:i386 libgettextpo0:i386 libxss1:i386 libgd2-xpm:i386 libheimbase1-heimdal:i386 libtiff4:i386 libsdl-net1.2:i386 libjasper1:i386 libgnome-keyring0:i386 libxtst6:i386 gtk2-engines-pixbuf:i386 libqtgui4:i386 libtag1c2a:i386 librsvg2-2:i386 libavahi-client3:i386 libssl0.9.8:i386 libmpg123-0:i386 libmad0:i386 libsasl2-2:i386 xorg-sgml-doctools libgsoap1 gtk2-engines-oxygen:i386 libfontconfig1:i386 xaw3dg:i386 libpango1.0-0:i386 libsm6:i386 libx11-dev libheimntlm0-heimdal:i386 libpulsedsp:i386 lib32stdc++6 libx11-doc libqt4-sql-mysql:i386 libxcb-render0:i386 libodbc1:i386 libexif12:i386 libqt4-scripttools:i386 librtmp0:i386 libgssapi-krb5-2:i386 libxi6:i386 libqtwebkit4:i386 libxcb1-dev libxp6:i386 libaudio2:i386 libxcursor1:i386 libxcb-shm0:i386 libxt6:i386 libxv1:i386 libsasl2-modules:i386 libavahi-common3:i386 libxrandr2:i386 x11proto-core-dev libsqlite3-0:i386 libmng1:i386 libgtk2.0-0:i386 libxdmcp-dev libpthread-stubs0-dev libltdl7:i386 libkrb5-26-heimdal:i386 libssl1.0.0:i386 glib-networking:i386 libgpg-error0:i386 libsoup2.4-1:i386 libgphoto2-2:i386 libtag1-vanilla:i386 libaudiofile1:i386 libglade2-0:i386 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal Suggested packages: icedtea-plugin sun-java6-fonts fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts python3-doc python3-tk python3.2-doc binfmt-support The following packages will be REMOVED: activity-log-manager-control-center aisleriot alacarte apparmor apport apport-gtk apt-xapian-index aptdaemon apturl apturl-common bluez bluez-alsa bluez-alsa:i386 bluez-gstreamer checkbox checkbox-qt command-not-found compiz compiz-gnome compiz-plugins-main-default compizconfig-backend-gconf deja-dup duplicity eog evolution-data-server firefox firefox-globalmenu firefox-gnome-support foomatic-db-compressed-ppds gconf-editor gconf2 gdb gedit gir1.2-mutter-3.0 gir1.2-peas-1.0 gir1.2-rb-3.0 gir1.2-totem-1.0 gir1.2-ubuntuoneui-3.0 gksu gnome-applets gnome-applets-data gnome-bluetooth gnome-contacts gnome-control-center gnome-media gnome-menus gnome-orca gnome-panel gnome-panel-data gnome-session-fallback gnome-shell gnome-sudoku gnome-terminal gnome-terminal-data gnome-themes-standard gnome-tweak-tool gnome-user-share gstreamer0.10-gconf gwibber gwibber-service gwibber-service-facebook gwibber-service-identica gwibber-service-twitter hplip hplip-data ia32-libs ia32-libs-multiarch:i386 ibus ibus-pinyin ibus-table indicator-datetime indicator-power jockey-common jockey-gtk landscape-client-ui-install language-selector-common language-selector-gnome launchpad-integration libcanberra-gtk-module libcanberra-gtk-module:i386 libcanberra-gtk3-module libcompizconfig0 libfolks-eds25 libgksu2-0 libgnome-media-profiles-3.0-0 libgnome2-0 libgnome2-common libgnomevfs2-0 libgnomevfs2-common libgweather-3-0 libgweather-common libgwibber-gtk2 libgwibber2 libmetacity-private0 libmutter0 libpeas-1.0-0 libpurple-bin libpython2.7 libreoffice-gnome librhythmbox-core5 libsyncdaemon-1.0-1 libtotem0 libubuntuoneui-3.0-1 light-themes lsb-release metacity metacity-common mutter-common nautilus-dropbox nautilus-share network-manager-gnome nvidia-common nvidia-settings nvidia-settings-updates onboard oneconf openjdk-7-jdk openjdk-7-jre openprinting-ppds pidgin pidgin-libnotify pidgin-otr printer-driver-foo2zjs printer-driver-ptouch printer-driver-pxljr printer-driver-sag-gdi printer-driver-splix python python-appindicator python-apport python-apt python-apt-common python-aptdaemon python-aptdaemon.gtk3widgets python-aptdaemon.pkcompat python-brlapi python-cairo python-central python-chardet python-configglue python-crypto python-cups python-cupshelpers python-dateutil python-dbus python-debian python-debtagshw python-defer python-dirspec python-egenix-mxdatetime python-egenix-mxtools python-gconf python-gdbm python-gi python-gi-cairo python-glade2:i386 python-gmenu python-gnomekeyring python-gnupginterface python-gobject python-gobject-2 python-gpgme python-gst0.10 python-gtk2 python-httplib2 python-ibus python-imaging python-keyring python-launchpadlib python-lazr.restfulclient python-lazr.uri python-libproxy python-libxml2 python-louis python-mako python-markupsafe python-minimal python-notify python-numeric:i386 python-oauth python-openssl python-packagekit python-pam python-pexpect python-piston-mini-client python-pkg-resources python-problem-report python-protobuf python-pyatspi2 python-pycurl python-pyinotify python-renderpm python-reportlab python-reportlab-accel python-serial python-simplejson python-smbc python-software-properties python-speechd python-twisted-bin python-twisted-core python-twisted-names python-twisted-web python-ubuntu-sso-client python-ubuntuone-client python-ubuntuone-control-panel python-ubuntuone-storageprotocol python-uno python-virtkey python-wadllib python-xapian python-xdg python-xkit python-zeitgeist python-zope.interface python2.7 python2.7-minimal rhythmbox rhythmbox-mozilla rhythmbox-plugin-cdrecorder rhythmbox-plugin-magnatune rhythmbox-plugin-zeitgeist rhythmbox-plugins rhythmbox-ubuntuone screen-resolution-extra sessioninstaller skype software-center software-center-aptdaemon-plugins software-properties-common software-properties-gtk system-config-printer-common system-config-printer-gnome system-config-printer-udev texlive-extra-utils totem totem-mozilla totem-plugins ubuntu-artwork ubuntu-desktop ubuntu-minimal ubuntu-sso-client ubuntu-sso-client-gtk ubuntu-standard ubuntu-system-service ubuntuone-client ubuntuone-client-gnome ubuntuone-control-panel ubuntuone-couch ubuntuone-installer ufw unattended-upgrades unity unity-2d unity-common unity-lens-applications unity-lens-video unity-scope-musicstores unity-scope-video-remote update-manager update-manager-core update-notifier update-notifier-common usb-creator-common usb-creator-gtk virtualbox virtualbox-dkms virtualbox-qt xdiagnose xul-ext-ubufox zeitgeist zeitgeist-core zeitgeist-datahub The following NEW packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal WARNING: The following essential packages will be removed. This should NOT be done unless you know exactly what you are doing! python-minimal python2.7-minimal (due to python-minimal) 0 upgraded, 16 newly installed, 273 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 39.1 MB of archives. After this operation, 324 MB disk space will be freed. You are about to do something potentially harmful. To continue type in the phrase 'Yes, do as I say!' ?] Thats not good, is it?! Should i run this command or should i run another command to fix this problem? Would be great if somebody can help me. :) Thanks in advance. best regards

  Read the article

• Ajax Control Toolkit Now Supports jQuery

  - by Stephen.Walther

  I’m excited to announce the September 2013 release of the Ajax Control Toolkit, which now supports building new Ajax Control Toolkit controls with jQuery. You can download the latest release of the Ajax Control Toolkit from http://AjaxControlToolkit.CodePlex.com or you can install the Ajax Control Toolkit directly within Visual Studio by executing the following NuGet command: The New jQuery Extender Base Class This release of the Ajax Control Toolkit introduces a new jQueryExtender base class. This new base class enables you to create Ajax Control Toolkit controls with jQuery instead of the Microsoft Ajax Library. Currently, only one control in the Ajax Control Toolkit has been rewritten to use the new jQueryExtender base class (only one control has been jQueryized). The ToggleButton control is the first of the Ajax Control Toolkit controls to undergo this dramatic transformation. All of the other controls in the Ajax Control Toolkit are written using the Microsoft Ajax Library. We hope to gradually rewrite these controls as jQuery controls over time. You can view the new jQuery ToggleButton live at the Ajax Control Toolkit sample site: http://www.asp.net/ajaxLibrary/AjaxControlToolkitSampleSite/ToggleButton/ToggleButton.aspx Why are we rewriting Ajax Control Toolkits with jQuery? There are very few developers actively working with the Microsoft Ajax Library while there are thousands of developers actively working with jQuery. Because we want talented developers in the community to continue to contribute to the Ajax Control Toolkit, and because almost all JavaScript developers are familiar with jQuery, it makes sense to support jQuery with the Ajax Control Toolkit. Also, we believe that the Ajax Control Toolkit is a great framework for Web Forms developers who want to build new ASP.NET controls that use JavaScript. The Ajax Control Toolkit has great features such as automatic bundling, minification, caching, and compression. We want to make it easy for ASP.NET developers to build new controls that take advantage of these features. Instantiating Controls with data-* Attributes We took advantage of the new JQueryExtender base class to change the way that Ajax Control Toolkit controls are instantiated. In the past, adding an Ajax Control Toolkit to a page resulted in inline JavaScript being injected into the page. For example, adding the ToggleButton control to a page injected the following HTML and script: <input id="ctl00_SampleContent_CheckBox1" name="ctl00$SampleContent$CheckBox1" type="checkbox" checked="checked" /> <script type="text/javascript"> //<![CDATA[ Sys.Application.add_init(function() { $create(Sys.Extended.UI.ToggleButtonBehavior, {"CheckedImageAlternateText":"Check", "CheckedImageUrl":"ToggleButton_Checked.gif", "ImageHeight":19, "ImageWidth":19, "UncheckedImageAlternateText":"UnCheck", "UncheckedImageUrl":"ToggleButton_Unchecked.gif", "id":"ctl00_SampleContent_ToggleButtonExtender1"}, null, null, $get("ctl00_SampleContent_CheckBox1")); }); //]]> </script> Notice the call to the JavaScript $create() method at the bottom of the page. When using the Microsoft Ajax Library, this call to the $create() method is necessary to create the Ajax Control Toolkit control. This inline script looks pretty ugly to a modern JavaScript developer. Inline script! Horrible! The jQuery version of the ToggleButton injects the following HTML and script into the page: <input id="ctl00_SampleContent_CheckBox1" name="ctl00$SampleContent$CheckBox1" type="checkbox" checked="checked" data-act-togglebuttonextender="imageWidth:19, imageHeight:19, uncheckedImageUrl:'ToggleButton_Unchecked.gif', checkedImageUrl:'ToggleButton_Checked.gif', uncheckedImageAlternateText:'I don&#39;t understand why you don&#39;t like ASP.NET', checkedImageAlternateText:'It&#39;s really nice to hear from you that you like ASP.NET'" /> Notice that there is no script! There is no call to the $create() method. In fact, there is no inline JavaScript at all. The jQuery version of the ToggleButton uses an HTML5 data-* attribute instead of an inline script. The ToggleButton control is instantiated with a data-act-togglebuttonextender attribute. Using data-* attributes results in much cleaner markup (You don’t need to feel embarrassed when selecting View Source in your browser). Ajax Control Toolkit versus jQuery So in a jQuery world why is the Ajax Control Toolkit needed at all? Why not just use jQuery plugins instead of the Ajax Control Toolkit? For example, there are lots of jQuery ToggleButton plugins floating around the Internet. Why not just use one of these jQuery plugins instead of using the Ajax Control Toolkit ToggleButton control? There are three main reasons why the Ajax Control Toolkit continues to be valuable in a jQuery world: Ajax Control Toolkit controls run on both the server and client jQuery plugins are client only. A jQuery plugin does not include any server-side code. If you need to perform any work on the server – think of the AjaxFileUpload control – then you can’t use a pure jQuery solution. Ajax Control Toolkit controls provide a better Visual Studio experience You don’t get any design time experience when you use jQuery plugins within Visual Studio. Ajax Control Toolkit controls, on the other hand, are designed to work with Visual Studio. For example, you can use the Visual Studio Properties window to set Ajax Control Toolkit control properties. Ajax Control Toolkit controls shield you from working with JavaScript I like writing code in JavaScript. However, not all developers like JavaScript and some developers want to completely avoid writing any JavaScript code at all. The Ajax Control Toolkit enables you to take advantage of JavaScript (and the latest features of HTML5) in your ASP.NET Web Forms websites without writing a single line of JavaScript. Better ToolkitScriptManager Documentation With this release, we have added more detailed documentation for using the ToolkitScriptManager. In particular, we added documentation that describes how to take advantage of the new bundling, minification, compression, and caching features of the Ajax Control Toolkit. The ToolkitScriptManager documentation is part of the Ajax Control Toolkit sample site and it can be read here: http://www.asp.net/ajaxLibrary/AjaxControlToolkitSampleSite/ToolkitScriptManager/ToolkitScriptManager.aspx Other Fixes This release of the Ajax Control Toolkit includes several important bug fixes. For example, the Ajax Control Toolkit Twitter control was completely rewritten with this release. Twitter is in the process of retiring the first version of their API. You can read about their plans here: https://dev.twitter.com/blog/planning-for-api-v1-retirement We completely rewrote the Ajax Control Toolkit Twitter control to use the new Twitter API. To take advantage of the new Twitter API, you must get a key and access token from Twitter and add the key and token to your web.config file. Detailed instructions for using the new version of the Ajax Control Toolkit Twitter control can be found here: http://www.asp.net/ajaxLibrary/AjaxControlToolkitSampleSite/Twitter/Twitter.aspx   Summary We’ve made some really great changes to the Ajax Control Toolkit over the last two releases to modernize the toolkit. In the previous release, we updated the Ajax Control Toolkit to use a better bundling, minification, compression, and caching system. With this release, we updated the Ajax Control Toolkit to support jQuery. We also continue to update the Ajax Control Toolkit with important bug fixes. I hope you like these changes and I look forward to hearing your feedback.

  Read the article

• Consume WCF Service InProcess using Agatha and WCF

  - by REA_ANDREW

  I have been looking into this lately for a specific reason.  Some integration tests I want to write I want to control the types of instances which are used inside the service layer but I want that control from the test class instance.  One of the problems with just referencing the service is that a lot of the time this will by default be done inside a different process.  I am using StructureMap as my DI of choice and one of the tools which I am using inline with RhinoMocks is StructureMap.AutoMocking.  With StructureMap the main entry point is the ObjectFactory.  This will be process specific so if I decide that the I want a certain instance of a type to be used inside the ServiceLayer I cannot configure the ObjectFactory from my test class as that will only apply to the process which it belongs to. This is were I started thinking about two things: Running a WCF in process Being able to share mocked instances across processes A colleague in work pointed me to a project which is for the latter but I thought that it would be a better solution if I could run the WCF Service in process.  One of the projects which I use when I think about WCF Services is AGATHA, and the one which I have to used to try and get my head around doing this. Another asset I have is a book called Programming WCF Services by Juval Lowy and if you have not heard of it or read it I would definately recommend it.  One of the many topics that is inside this book is the type of configuration you need to communicate with a service in the same process, and it turns out to be quite simple from a config point of view. <system.serviceModel> <services> <service name="Agatha.ServiceLayer.WCF.WcfRequestProcessor"> <endpoint address ="net.pipe://localhost/MyPipe" binding="netNamedPipeBinding" contract="Agatha.Common.WCF.IWcfRequestProcessor"/> </service> </services> <client> <endpoint name="MyEndpoint" address="net.pipe://localhost/MyPipe" binding="netNamedPipeBinding" contract="Agatha.Common.WCF.IWcfRequestProcessor"/> </client> </system.serviceModel>   You can see here that I am referencing the Agatha object and contract here, but also that my binding and the address is something called Named Pipes.  THis is sort of the “Magic” which makes it happen in the same process. Next I need to open the service prior to calling the methods on a proxy which I also need.  My initial attempt at the proxy did not use any Agatha specific coding and one of the pains I found was that you obviously need to give your proxy the known types which the serializer can be aware of.  So we need to add to the known types of the proxy programmatically.  I came across the following blog post which showed me how easy it was http://bloggingabout.net/blogs/vagif/archive/2009/05/18/how-to-programmatically-define-known-types-in-wcf.aspx. First Pass So with this in mind, and inside a console app this was my first pass at consuming a service in process.  First here is the proxy which I made making use of the Agatha IWcfRequestProcessor contract. public class InProcProxy : ClientBase<Agatha.Common.WCF.IWcfRequestProcessor>, Agatha.Common.WCF.IWcfRequestProcessor { public InProcProxy() { } public InProcProxy(string configurationName) : base(configurationName) { } public Agatha.Common.Response[] Process(params Agatha.Common.Request[] requests) { return Channel.Process(requests); } public void ProcessOneWayRequests(params Agatha.Common.OneWayRequest[] requests) { Channel.ProcessOneWayRequests(requests); } } So with the proxy in place I could then use this after opening the service so here is the code which I use inside the console app make the request. static void Main(string[] args) { ComponentRegistration.Register(); ServiceHost serviceHost = new ServiceHost(typeof(Agatha.ServiceLayer.WCF.WcfRequestProcessor)); serviceHost.Open(); Console.WriteLine("Service is running...."); using (var proxy = new InProcProxy()) { foreach (var operation in proxy.Endpoint.Contract.Operations) { foreach (var t in KnownTypeProvider.GetKnownTypes(null)) { operation.KnownTypes.Add(t); } } var request = new GetProductsRequest(); var responses = proxy.Process(new[] { request }); var response = (GetProductsResponse)responses[0]; Console.WriteLine("{0} Products have been retrieved", response.Products.Count); } serviceHost.Close(); Console.WriteLine("Finished"); Console.ReadLine(); } So what I used here is the KnownTypeProvider of Agatha to easily get all the types I need for the service/proxy and add them to the proxy.  My Request handler for this was just a test one which always returned 2 products. public class GetProductsHandler : RequestHandler<GetProductsRequest,GetProductsResponse> { public override Agatha.Common.Response Handle(GetProductsRequest request) { return new GetProductsResponse { Products = new List<ProductDto> { new ProductDto{}, new ProductDto{} } }; } } Second Pass Now after I did this I started reading up some more on some resources including more by Davy Brion and others on Agatha.  Now it turns out that the work I did above to create a derived class of the ClientBase implementing Agatha.Common.WCF.IWcfRequestProcessor was not necessary due to a nice class which is present inside the Agatha code base, RequestProcessorProxy which takes care of this for you! :-) So disregarding that class I made for the proxy and changing my code to use it I am now left with the following: static void Main(string[] args) { ComponentRegistration.Register(); ServiceHost serviceHost = new ServiceHost(typeof(Agatha.ServiceLayer.WCF.WcfRequestProcessor)); serviceHost.Open(); Console.WriteLine("Service is running...."); using (var proxy = new RequestProcessorProxy()) { var request = new GetProductsRequest(); var responses = proxy.Process(new[] { request }); var response = (GetProductsResponse)responses[0]; Console.WriteLine("{0} Products have been retrieved", response.Products.Count); } serviceHost.Close(); Console.WriteLine("Finished"); Console.ReadLine(); }   Cheers for now, Andy References Agatha WCF InProcess Without WCF StructureMap.AutoMocking Cross Process Mocking Agatha Programming WCF Services by Juval Lowy

  Read the article

< Previous Page | 981 982 983 984 985 986 987 988 989 990 991 992  | Next Page >