Daily Archives

Articles indexed Monday September 24 2012

Page 1/18 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• What else is needed to get iptables to log into this file I created?

  - by anthony01

  I want to create the logging of iptables DROP's and intrusion attemps. First, I put --log-prefix "iptables: " at the end of every iptables rules in my iptables rules file. But this doesn't work, as it says there is a syntax error. So where should I put that command? (I would want to have it included in the saved rules file) Secondly, I created a file iptables.conf within /etc/rsyslog.d/, and I put the following inside of it: :msg, startswith, "iptables: " -/var/log/iptables.log & ~ I assume that at this stage, I'm supposed to restart the rsyslog daemon. What else is needed to do what I'm attempting? Thanks a lot

  Read the article

• Long Gigabit Ethernet Run

  - by Timothy R. Butler

  I am trying to get an Gig-E network between two buildings that are approximately 260 ft. away. While some TRENDnet switches failed to be able to connect to each other over Cat 6 at that distance, two Netgear 5-port Gig-E switches do so just fine. However, it still fails after I put in place APC PNET1GB ethernet surge protectors at each end before the line connects to the respective switches. So I find myself wondering if I simply need to find a better surge protector that doesn't degrade the signal as much (if so, what kind would you recommend?) or if I should give up on copper and use fiber between the buildings. If I opt to go the latter route, I could really use some pointers. It looks like LC connectors are the most common, but I keep running into some others as well. A media converter on each end seems like the simplest solution, but perhaps a Gig-E switch with an SFP port would make more sense? Given a very limited budget, sticking with my existing copper seems best, but if it is bound to be a headache, a 100 meter fiber cable is something I think I can swing cost wise.

  Read the article

• More than 3 seconds "Initial Connection" time (webpagetest.org)

  - by George Tasioulis

  I'm having a weird issue with a vBulletin forum, on a 2? Xeon E5645 w/ 16GB RAM, cPanel and LiteSpeed webserver; It takes too long to start loading... When I tested it with webpagetest.org I saw that for every request there's a 3 second "Initial connection" delay, which I don't know why is happening. Here's a screenshot: CPU Load is between 0.03 and 0.05, I've got several GB of free RAM, practical no I/O activity, and this delay can occur even with only one visitor on the forum. Where do you suggest I start searching? What could be the reason for this kind of delay? I don't think it's the webserver, or the forum because there's another website on the server (total 2 sites) which is WordPress based, and has exactly the same issue with the 3 second initial connection delay. I believe it's OS related, but need a clue on where to start looking. Thanks in advance :)

  Read the article

• Monitoring outgoing bandwidth of application

  - by jnolte

  I currently have a VPS that is consuming a ton of outgoing bandwidth and I am trying to drill down to where this may be coming from. Does anyone know of a logical way to go about finding out which pages on the site are consuming the most outgoing data. We have done a ton of front-end optimizations to the site and our google page speed rankings ar 85% so I feel we have done a pretty great job at optimizing the site for speed. Can someone lend some insight on how they have made similar optimizations? Application / Server Stack LEMP Running Varnish Cache / PHP5-FPM WordPress running w3 Total Cache Ubuntu 12.04 LTS

  Read the article

• External Display connected to Macbook pro won't sleep

  - by Moiz

  I have Macbook Pro with OSX 10.6.8. It is connected to external display (HP 2311x) using Thunderbolt to HDMI cable. My Macbook display goes to sleep after every 15 minutes of inactivity but the external display won't go to sleep. It does try to go to sleep but wake up immediately. It does that in never ending loop. I have to manually turn off the external display. Is there some settings I need to change to make external display sleep when Macbook display goes to sleep? Any suggestions? Thanks in advance!!

  Read the article

• custom route not working on windows

  - by Michael Closson

  My windows laptop is directly connected to 192.168.1.0/24 (wireless lan). I access 10.21.0.0/16 though a router that is connected to both networks. The routing works fine with this configuration. I have a VPN, that connects to 10.0.0.0/8. The VPN network doesn't actually use any IPs in the 10.21.0.0/16 range. So I should be able to configure my routing table to route all the 10.21.0.0/16 IPs through the wireless lan, and all other 10.0.0.0/8 through the VPN. My understanding is that I can do this if the metric for the 10.21.0.0 is lower than that of the 10.0.0.0. The VPN (10.0.0.0) is automatically assigned metric 20. I have manually assigned the WLAN a metric of 1. I manually add an entry to the routing table with this command: route add 10.21.0.0 mask 255.255.0.0 192.168.1.201 metric 1 The route is then assigned a metric of 2 (which is expected). The problem is that it doesn't work. I can't ping any machine on the 10.21.0.0 network. But I can access other stuff on the 10.0.0.0. I can also access stuff on the 192.168.1.0. To debug this i've done the following. Run tcpdump on the router (192.168.1.201). I can verify that no packets for 10.21.0.0 arrive on that interface. Disable iptables on the router. Disable the windows firewall. Run wireshark on my laptop, to try and see which interface the ping requests go to. But I can't see them go anywhere!! The ping command doesn't receive any 'destination unreachable' messages. Here is the relevant section of the routing table. IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.201 192.168.1.18 2 10.0.0.0 255.0.0.0 On-link 10.55.44.203 20 10.21.0.0 255.255.0.0 192.168.1.201 192.168.1.18 2

  Read the article

• Website Upgrade - Avoid Downtime

  - by nolan.sipos

  I have been requested to investigate how I can reduce the downtime of our website upgrades. We maintain a DNN site with both public facing pages and member only pages. The member only pages are directly linked to our core application database while the public pages are not. Our current process is to redirect website users as soon as the upgrade process begins, which includes Backup of the Prod DB Update Prod DB Update Executables (Application) Upgrade Website Application (If this requires an update) Install Dependencies Upgrade sub systems like communication engine and payment broker Update various configuration files Perform testing of systems Restart all services Allow access to site This process can take from 2 to 8 hours depending on upgrade required, scripts to be run, size of database and number or portals. My initial thoughts are to restrict users to read only pages and any update pages would be unavailable. Could anyone please offer suggestions as to the best practices for what I would think to be a common problem so that we can reduce this down time and if we need infrastructure changes, I can put this to our technical department.

  Read the article

• How do I set a postgresql password in pgpass.conf for the Administrator account on Windows Server 2008?

  - by brad

  I have a pgpass.conf file that works well for my default user. It is in C:/Users/myuser/AppData/Roaming/postgresql/pgpass.conf. It reads like so; localhost:5432:*:postgres:password1 I have a process that runs under the Administrator account. When I run whoami under this process I get nt authority/system. I want to be able to access the database from this process but it gets stuck because it needs a password. I have tried putting the above pgpass.conf into C:/Users/Administrator/AppData/postgresql/pgpass.conf and C:/Users/Administrator/AppData/Roaming/postgresql/pgpass.conf but it does not work. Is this the correct place for this file? Am I even able to do this as the Administrator. Unfortunately I cannot change the user that this process runs under.

  Read the article

• Intermittent internet access on a flat network - Router is connected

  - by Naveed

  I’m looking for some help with network settings. I’ve just started a new job (non-IT!) and we have problems with our office network. I’m the most IT literate in the organisation (15 permanent employees) and so have been dealing with IT issues. Our main bit of software is web-based so we need constant web access but it sometimes goes down for between 20 minutes and 3 hours despite everything seemingly working fine. It’s a flat network with wireless APs, BT Business Broadband 8Mbit connection and that’s about it. We have no servers and no standard settings and staff are encouraged to bring in their own laptops and connect! The network basically exists to provide internet access and that’s it. We also have students accessing the wireless (and I know there’s a whole list of access and content issues etc but right now we just need internet access stabilised). This is what we have: Building 1 Cisco SLM-224P 24-port PoE 10/100 switch with 2 gigabit ports 3 x ZyXEL NWA-3160 wireless APs Samsung OfficeServ 7100 phone server which borrows the building’s wiring Building 2 Netgear GS605-UK 5-port 10/100/1000 switch 1 x ZyXEL NWA-3160 wireless AP 1 x BT Business Hub – 2wire BT2700hgv – is the DHCP server We have 2 link cables between the buildings. One connects the two switches on a gigabit port. The second (oddly) connects the switch in building 2 to the OfficeServ server in building 1. When the internet goes down I can still access the router through a wireless connection. I can also ping websites and get a response. Firefox just says “Cannot connect” etc. The system then heals itself when it feels like it. (Sorry if this is asking too much but) These are my immediate questions… Why would browser-based internet go down? I don’t know enough about protocols etc but I can try to standardise settings. The WAPs have a DNS server setting and I don’t know whether it should be “None” or “From DHCP”. What should be the DHCP server? The router or the Cisco switch? Or something else?! Would there be any problem in connecting the second link from switch to switch? Is that good practice? Is it worth swapping the Netgear GS605 with either a Cisco SG200-08 or Netgear GS108T-200? Is it worth upgrading the router to, for instance, a Cisco RV042G Dual Gigabit router which would also act as a switch? Or is it better to have a separate router and switch in Building 2?

  Read the article

• How do I disable Tomcat? [closed]

  - by Dave King Popeye Mason

  Possible Duplicate: How to disable Tomcat on linux? According to my server host, something called Tomcat is hogging all my resources and slowing down the server. As far as I'm aware I'm not using it as the only thing running on the server is Plesk and a few Wordpress installations. I'm a real dummy at using SSH, I can navigate to folders, change permissions and that's about it. Could somebody explain to me as if I'm a 5 year old how to disable TomCat (and also how to stop it re-enabling on startup)? Thanks!

  Read the article

• What consequences to take from what i read in logfiles?

  - by Helene Bilbo

  Since some weeks i manage my first Webserver, a Seaside application behind an Apache proxy on Linode, and i installed logwatch to send me daily logs. Where can i get information on when i have to act as a consequence of what i read in these logwatch reports? For example i read that all kinds of people try to login on funny nonexisting accounts or all kinds of webcrawlers test for nonexisting cms login pages, some ip adresses get banned and unbanned by fail2ban... I assume that's normal? Is it? But how do i know that i probably have to do something? What do i look for in the logs?

  Read the article

• Debian 6 Server Enabling Remote Desktop [closed]

  - by Sampath

  I am currently running a web server on Debian 6 without a GUI. I connect to the server through SSH using putty from my Windows desktop. When managing Windows systems we use RDP to connect remotely, so how would I do the same for my Debian server? Note: I am not an linux power user. My Debian 6 server is a web server serving ruby on rails+mysql, so I would prefer a light weight remote desktop solution.

  Read the article

• Teamcity nuget feed http authentication

  - by Mihalis Bagos

  Nuget feed by team city is working perfectly but there is a strange problem. Local IP (http://192.168.xx.xx:9999/feed/../): Listing through browser works Accessing packages through Visual studio 11 nuget works VPN IP (http://55.xx.xx.xx:9999/feed/../): Listing packages through browser works Accessing packages through Visual studio 11 nuget PROBLEM GUEST Account: Everything works fine, both on VPN and local IP (so its purely an authentication problem) The problem is, we can't get the user to authenticate. Using the same credentials, no matter what we try we get 401. The server VPN ip is whitelisted in internet explorer intranet settings. Any ideas? Basically HTTP authentication is failing for the VPN although it shouldn't, since the browser works fine!

  Read the article

• MySQLi Extension with phpMyAdmin

  - by user1062058

  I just unpacked the latest phpMyAdmin into /var/www/html/phpMyAdmin and it is giving me "The mysqli extension is missing." - how do I install this? I'm on Centos. I checked php.ini and it seems to be "unlocked". when I type in php -i |grep -i mysqli ... it looks to be enabled. Also this is PHP Version 5.3.8 php -m apc ctype curl date dom filter ftp gd hash iconv json libxml mcrypt memcache mysql mysqli openssl pcre PDO pdo_sqlite posix REflection session SimpleXML soap SPL SQLite standard tokenizer xml xmlreader xmlwriter zlib Thanks.

  Read the article

• TIME_WAIT connections not being cleaned up after timeout period expires

  - by Mark Dawson

  I am stress testing one of my servers by hitting it with a constant stream of new network connections, the tcp_fin_timeout is set to 60, so if I send a constant stream of something like 100 requests per second, I would expect to see a rolling average of 6000 (60 * 100) connections in a TIME_WAIT state, this is happening, but looking in netstat (using -o) to see the timers, I see connections like: TIME_WAIT timewait (0.00/0/0) where their timeout has expired but the connection is still hanging around, I then eventually run out of connections. Anyone know why these connections don't get cleaned up? If I stop creating new connections they do eventually disappear but while I am constantly creating new connections they don't, seems like the kernel isn't getting chance to clean them up? Is there some other config options I need to set to remove the connections as soon as they have expired? The server is running Ubuntu and my web server is nginx. Also it has iptables with connection tracking, not sure if that would cause these TIME_WAIT connections to live on. Thanks Mark.

  Read the article

• Understanding Zabbix Triggers

  - by Mediocre Gopher

  I have zabbix set with an item to monitor a log file on a zabbix client: log["/var/log/program_name/client.log","ERROR:","UTF-8",100] And a trigger to determine when that log file get's more ERRORs: {Template_Linux:log["/var/log/program_name/client.log","ERROR:","UTF-8",100].change(0)}#0 This trigger gets tripped when the log file gets ERRORs the first time, but then that first trigger just sits around for ever in Monitoring-Triggers. My understanding is that the next time the server checks the value of log["/var/log/program_name/client.log","ERROR:","UTF-8",100] and sees that it hasn't changed that the trigger would go away. Obviously this isn't the case. Could someone explain why this first trigger isn't going away? Ultimately my goal is to receive an email whenever ERRORs are added to that log file, but I would like to understand how triggers are working first.

  Read the article

• Problem using a public key when connecting to a SSH server running on Cygwin

  - by Deleted

  We have installed Cygwin on a Windows Server 2008 Standard server and it working pretty well. Unfortunately we still have a big problem. We want to connect using a public key through SSH which doesn't work. It always falls back to using password login. We have appended our public key to ~/.ssh/authorized_keys on the server and we have our private and public key in ~/.ssh/id_dsa respective ~/.ssh/id_dsa.pub on the client. When debugging the SSH login session we see that the key is offered by the server apparently rejects it by some unknown reason. The SSH output when connecting from an Ubuntu 9.10 desktop with debug information enabled: $ ssh -v 192.168.10.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /home/myuseraccount/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for debug1: Connecting to 192.168.10.11 [192.168.10.11] port 22. debug1: Connection established. debug1: identity file /home/myuseraccount/.ssh/identity type -1 debug1: identity file /home/myuseraccount/.ssh/id_rsa type -1 debug1: identity file /home/myuseraccount/.ssh/id_dsa type 2 debug1: Checking blacklist file /usr/share/ssh/blacklist.DSA-1024 debug1: Checking blacklist file /etc/ssh/blacklist.DSA-1024 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '192.168.10.11' is known and matches the RSA host key. debug1: Found key in /home/myuseraccount/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: /home/myuseraccount/.ssh/id_dsa debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: /home/myuseraccount/.ssh/identity debug1: Trying private key: /home/myuseraccount/.ssh/id_rsa debug1: Next authentication method: keyboard-interactive debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: password [email protected]'s password: The version of Cygwin: $ uname -a CYGWIN_NT-6.0 servername 1.7.1(0.218/5/3) 2009-12-07 11:48 i686 Cygwin The installed packages: $ cygcheck -c Cygwin Package Information Package Version Status _update-info-dir 00871-1 OK alternatives 1.3.30c-10 OK arj 3.10.22-1 OK aspell 0.60.5-1 OK aspell-en 6.0.0-1 OK aspell-sv 0.50.2-2 OK autossh 1.4b-1 OK base-cygwin 2.1-1 OK base-files 3.9-3 OK base-passwd 3.1-1 OK bash 3.2.49-23 OK bash-completion 1.1-2 OK bc 1.06-2 OK bzip2 1.0.5-10 OK cabextract 1.1-1 OK compface 1.5.2-1 OK coreutils 7.0-2 OK cron 4.1-59 OK crypt 1.1-1 OK csih 0.9.1-1 OK curl 7.19.6-1 OK cvs 1.12.13-10 OK cvsutils 0.2.5-1 OK cygrunsrv 1.34-1 OK cygutils 1.4.2-1 OK cygwin 1.7.1-1 OK cygwin-doc 1.5-1 OK cygwin-x-doc 1.1.0-1 OK dash 0.5.5.1-2 OK diffutils 2.8.7-2 OK doxygen 1.6.1-2 OK e2fsprogs 1.35-3 OK editrights 1.01-2 OK emacs 23.1-10 OK emacs-X11 23.1-10 OK file 5.04-1 OK findutils 4.5.5-1 OK flip 1.19-1 OK font-adobe-dpi75 1.0.1-1 OK font-alias 1.0.2-1 OK font-encodings 1.0.3-1 OK font-misc-misc 1.1.0-1 OK fontconfig 2.8.0-1 OK gamin 0.1.10-10 OK gawk 3.1.7-1 OK gettext 0.17-11 OK gnome-icon-theme 2.28.0-1 OK grep 2.5.4-2 OK groff 1.19.2-2 OK gvim 7.2.264-1 OK gzip 1.3.12-2 OK hicolor-icon-theme 0.11-1 OK inetutils 1.5-6 OK ipc-utils 1.0-1 OK keychain 2.6.8-1 OK less 429-1 OK libaspell15 0.60.5-1 OK libatk1.0_0 1.28.0-1 OK libaudio2 1.9.2-1 OK libbz2_1 1.0.5-10 OK libcairo2 1.8.8-1 OK libcurl4 7.19.6-1 OK libdb4.2 4.2.52.5-2 OK libdb4.5 4.5.20.2-2 OK libexpat1 2.0.1-1 OK libfam0 0.1.10-10 OK libfontconfig1 2.8.0-1 OK libfontenc1 1.0.5-1 OK libfreetype6 2.3.12-1 OK libgcc1 4.3.4-3 OK libgdbm4 1.8.3-20 OK libgdk_pixbuf2.0_0 2.18.6-1 OK libgif4 4.1.6-10 OK libGL1 7.6.1-1 OK libglib2.0_0 2.22.4-2 OK libglitz1 0.5.6-10 OK libgmp3 4.3.1-3 OK libgtk2.0_0 2.18.6-1 OK libICE6 1.0.6-1 OK libiconv2 1.13.1-1 OK libidn11 1.16-1 OK libintl3 0.14.5-1 OK libintl8 0.17-11 OK libjasper1 1.900.1-1 OK libjbig2 2.0-11 OK libjpeg62 6b-21 OK libjpeg7 7-10 OK liblzma1 4.999.9beta-10 OK libncurses10 5.7-18 OK libncurses8 5.5-10 OK libncurses9 5.7-16 OK libopenldap2_3_0 2.3.43-1 OK libpango1.0_0 1.26.2-1 OK libpcre0 8.00-1 OK libpixman1_0 0.16.6-1 OK libpng12 1.2.35-10 OK libpopt0 1.6.4-4 OK libpq5 8.2.11-1 OK libreadline6 5.2.14-12 OK libreadline7 6.0.3-2 OK libsasl2 2.1.19-3 OK libSM6 1.1.1-1 OK libssh2_1 1.2.2-1 OK libssp0 4.3.4-3 OK libstdc++6 4.3.4-3 OK libtiff5 3.9.2-1 OK libwrap0 7.6-20 OK libX11_6 1.3.3-1 OK libXau6 1.0.5-1 OK libXaw3d7 1.5D-8 OK libXaw7 1.0.7-1 OK libxcb-render-util0 0.3.6-1 OK libxcb-render0 1.5-1 OK libxcb1 1.5-1 OK libXcomposite1 0.4.1-1 OK libXcursor1 1.1.10-1 OK libXdamage1 1.1.2-1 OK libXdmcp6 1.0.3-1 OK libXext6 1.1.1-1 OK libXfixes3 4.0.4-1 OK libXft2 2.1.14-1 OK libXi6 1.3-1 OK libXinerama1 1.1-1 OK libxkbfile1 1.0.6-1 OK libxml2 2.7.6-1 OK libXmu6 1.0.5-1 OK libXmuu1 1.0.5-1 OK libXpm4 3.5.8-1 OK libXrandr2 1.3.0-10 OK libXrender1 0.9.5-1 OK libXt6 1.0.7-1 OK links 1.00pre20-1 OK login 1.10-10 OK luit 1.0.5-1 OK lynx 2.8.5-4 OK man 1.6e-1 OK minires 1.02-1 OK mkfontdir 1.0.5-1 OK mkfontscale 1.0.7-1 OK openssh 5.4p1-1 OK openssl 0.9.8m-1 OK patch 2.5.8-9 OK patchutils 0.3.1-1 OK perl 5.10.1-3 OK rebase 3.0.1-1 OK run 1.1.12-11 OK screen 4.0.3-5 OK sed 4.1.5-2 OK shared-mime-info 0.70-1 OK tar 1.22.90-1 OK terminfo 5.7_20091114-13 OK terminfo0 5.5_20061104-11 OK texinfo 4.13-3 OK tidy 041206-1 OK time 1.7-2 OK tzcode 2009k-1 OK unzip 6.0-10 OK util-linux 2.14.1-1 OK vim 7.2.264-2 OK wget 1.11.4-4 OK which 2.20-2 OK wput 0.6.1-2 OK xauth 1.0.4-1 OK xclipboard 1.1.0-1 OK xcursor-themes 1.0.2-1 OK xemacs 21.4.22-1 OK xemacs-emacs-common 21.4.22-1 OK xemacs-sumo 2007-04-27-1 OK xemacs-tags 21.4.22-1 OK xeyes 1.1.0-1 OK xinit 1.2.1-1 OK xinput 1.5.0-1 OK xkbcomp 1.1.1-1 OK xkeyboard-config 1.8-1 OK xkill 1.0.2-1 OK xmodmap 1.0.4-1 OK xorg-docs 1.5-1 OK xorg-server 1.7.6-2 OK xrdb 1.0.6-1 OK xset 1.1.0-1 OK xterm 255-1 OK xz 4.999.9beta-10 OK zip 3.0-11 OK zlib 1.2.3-10 OK zlib-devel 1.2.3-10 OK zlib0 1.2.3-10 OK The ssh deamon configuration file: $ cat /etc/sshd_config # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/bin:/usr/sbin:/sbin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh_host_rsa_key #HostKey /etc/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes StrictModes no #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. #UsePAM no AllowAgentForwarding yes AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes X11DisplayOffset 10 X11UseLocalhost no #PrintMotd yes #PrintLastLog yes TCPKeepAlive yes #UseLogin no UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /usr/sbin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs #X11Forwarding yes #AllowTcpForwarding yes #ForceCommand cvs server I hope this information is enough to solve the problem. In case any more is needed please comment and I'll add it. Thank you for reading!

  Read the article

• ESXi 4.0 - cannot copy files

  - by user21368

  I am unable to copy files or make directories on my installation of VMWare ESXi 4.0. I have done so in the past (copied an iso onto a datastore). But something has changed and I have no idea what. I cannot copy using the datastore browser (get a dialog saying "Expected a PUT_FILE_DONE message. Got SESSION_COMPLETE"). I cannot create a directory through datastore browser (get a dialog saying "Cannot complete file creation operation"). When I ssh to the ESXi server I cannot create files or folders under /vmfs/volumes. But I can manipulate files elswhere (including /vmfs). Here are the permissions for the directories (I am logged in as root). ~ # ls -lh /vmfs/volumes/ drwxr-xr-t 1 root root 1.2k Sep 3 12:19 4a76f260-36b7eb85-c3b3-0024e8314929 drwxr-xr-x 1 root root 8 Jan 1 1970 4a76f261-d6190a9e-3b89-0024e8314929 drwxr-xr-t 1 root root 1.4k Sep 22 10:38 4a76f262-4ac21f0a-6bc1-0024e8314929 l--------- 0 root root 1.9k Jan 1 1970 Hypervisor1 - c42ce27f-eb8d7f70-7f70-0e7a85e8edc4 l--------- 0 root root 1.9k Jan 1 1970 Hypervisor2 - bbf1477b-4aec1d8c-caa5-5e8720bebd85 l--------- 0 root root 1.9k Jan 1 1970 Hypervisor3 - efd8efe3-03bc1cbf-15e0-080efd9e7379 drwxr-xr-x 1 root root 8 Jan 1 1970 bbf1477b-4aec1d8c-caa5-5e8720bebd85 drwxr-xr-x 1 root root 8 Jan 1 1970 c42ce27f-eb8d7f70-7f70-0e7a85e8edc4 l--------- 0 root root 1.9k Jan 1 1970 datastore1 - 4a76f260-36b7eb85-c3b3-0024e8314929 l--------- 0 root root 1.9k Jan 1 1970 datastore2 - 4a76f262-4ac21f0a-6bc1-0024e8314929 drwxr-xr-x 1 root root 8 Jan 1 1970 efd8efe3-03bc1cbf-15e0-080efd9e7379 ~ # touch /vmfs/foo.txt ~ # touch /vmfs/volumes/foo.txt touch: /vmfs/volumes/foo.txt: Operation not permitted I've googled and found nothing helpful. Does anyone out there have an idea as to what is going on? Thanks in Advance. Pete.

  Read the article

• Unable to write into character device file in Ubuntu

  - by Surjya Narayana Padhi

  I just written a linux character driver. I created one character device file named X. I can see that file in /dev folder. Now I want to do some read/write operation into this file. I opened the filed in VI editor and write some text into it. I used :wq and exited. It didn't show any error. Now when I do cat on that same file I am not able to see any content. I tried it several times. The same situation. Please let me know If I am doing something wrong....

  Read the article

• smb mount cannot sync file automatically

  - by Frank

  Under Ubuntu, I use smb to mount the directory of the server(Ubuntu too), and set to a local directory, like /home/username/server. When I change some files of local directory, the files in the server change too. However, when I change some files of the server, the files in local directory don't change. Does someone know what the reason is ? And could someone fix it and make local changes updated to the server so that I could edit local and make in the server?

  Read the article

• Mini DisplayPort to DVI-D Dual Link up to 2560 * 1600

  - by Steinway Wu

  I have a ThinkPad T530 with Mini DP++ and NVS 5400M, which are said to support 2560 * 1600 resolution. The display is Dell 3007WFP, which also supports 2560 * 1600. But, I have never seen any cables or adapters that can connect them with full support to 2560 * 1600. Do you have any idea? THANK YOU! In addition, I found that mDP++ means I can use a passive adapter. No need for active adapter which is much more expensive. This is the only one that meets my needs, but it is not sold in the US. And this one seems to be OK, but I am not sure because it says "2.5 Gbps per channel", which may not be enough.

  Read the article

• Can I use a SD card as cache instead of a Solid State Drive

  - by user654628

  I just installed a solid state drive a few days ago and I have been reading about how to preserve the file of it. I am running Windows 8 and my SSD has 256G of storage. I am using a laptop and cannot carry an external hard drive connected to my laptop to hold cache, temp files etc. I was wondering if a SD card would work. So I would use the SD card to hold cache, temp files and maybe index files from Windows, would this work and be effective (since I believe sd cards will also wear out)?

  Read the article

• How do I use an internal SSD as a scratch disk for FCP X?

  - by andrewb

  I'm contemplating setting up my MacBook Air as a video editing machine. If I do this, I'll upgrade to a 256 GB SSD, and I should be able to keep around 100 GB or more free for video editing. The video files would of course be stored externally, but save purchasing some expensive Thunderbolt RAID device (which I suppose is gradually becoming more of an option), it will be slow for read/writes. How can I have a set up where I take advantage of my SSD's speed for a scratch disk/cache for FCP X, but still have the TB(s) of storage of externals? I don't want to have to be moving files constantly back and forth, this is about saving time not wasting it.

  Read the article

• Google Chrome - Disable Location auto-detection also for google sites

  - by Michael

  I have read how to disable the location auto-detection here and also in Stackoverflow questions asked before: Google Chrome - Auto Detect Location and more... But it seems that it has no influence on the Google relates sites, e.g. Google translate, Google analytic, and even Google it self as a search engine. I have updated Google chrome to 21.0.1180.89 and then all my problems started, i am breaking my hand since i need to translate every word Google presents in their webpages of their products (or simply use their automatic translator). So i started to use Firefox again, but i really want to return back to Google, what can I do?

  Read the article

• Windows 7 keeps changing my language(keyboard) settings

  - by Hans

  I am using Windows 7 Ultimate on a Windows network. My default settings is Danish locale, Danish keyboardlayout, but English system language. I only have Danish keyboard layout installed (in Text Services and Input Languages). However, at the login screen I can choose Danish and English, but whatever I choose Windows 7 changes system language (and keyboard layout!) to English (United States). Since this is a per-App setting I must change the language setting (language bar in the taskbar) Where can this be changed system wide and permament?

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >