Monthly Archives

Articles indexed in March 2012

Page 31/239 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

• Default gateway is in different subnet. How to configure in RHEL6.2

  - by Dmytro Leonenko

  I have two subnets routed to my server from ISP. I have only one gateway ip. The gateway is on the same VLAN as my IP address. For example netowrk 1 is 1.0.0.0/24 and network 2 is 2.0.0.0/24. Both are routed to eth0 by my ISP. Gateway is 1.0.0.1. My host ip is 2.0.0.1/24 (eth0) So I can configure default gateway manually with ip route add default dev eth0 ip route add default via 1.0.0.1 and then internet connection works properly. How do I configure it in /etc/sysconfig/network-scripts/ifcfg-eth0 ? I tried to set GATEWAY=1.0.0.1 but it doesn't work. Tried to set GATEWAY and GATEWAYDEV in /etc/sysconfig/network and it does only what first command from listing above do.

  Read the article

• deploying AV via GPO only to workstations

  - by jeremy

  We have a small (100 machines) Windows domain running Server 2008R2. We use Symantec Endpoint Protection 12.1 I want to have GPO deploy the AV software to client machines automatically, but only to client workstations, not to servers, which run a different software. I've set it up before using a GPO linked to the domain mycompany.local and it works, but it deploys the AV software to ALL machines on the domain, including my servers. I can create an OU in active directory for Servers, and perhaps create one for client machines too, but I'd rather not have to go and move new domain members from the default under Computers into a different folder. How can I use GPO to deploy this AV software only to workstations on our network, and not to servers?

  Read the article

• Why is MySQL making the CPU run at about 80%?

  - by Robert

  MySQL is eating up about 80% of my CPU for no reason as far as I can see. Right now this server is rarely used, more of a test site I set up that will eventually be a used for production once I fix small problems like this. I run 3 instances of MySQL but it seems that my first instance is taking up all the CPU. When I turn off the first instance and leave the other two on everything runs fine. Any suggestions? I tried Show Processlist and no statements are being run besides "Sleep" and the query "Show Processlist" (obviously) at the time it's using up all this CPU. my.cnf is basic. I did not optimize or change any MySQL settings. Do you think this would cause such strange behavior? The machine is running Linux Centos 5.7 64 bit and MySQL 5.0.95. Thanks

  Read the article

• Managing rolling deployments in the cloud

  - by Josh Nankin

  Recently I've been experimenting with various cloud management tools like RightScale, Scalr, custom scripts for managing a variety of servers, each hosting several roles (app, db, load balancer, job queues, etc). The one thing I find lacking in most solutions is a way to do rolling deployments, i.e. running deployments sequentially across a number of servers with the same role. For instance, I dont want to build all of my webservers at the same time, as that will almost definitely result in some down time or 500s for my customers. I'd rather have one or two servers build at a time, while other servers are still available to handle requests. The other alternative is obviously to launch new servers that automatically update themselves on boot, but this isn't as cost effective, and most likely requires more time for the build to complete (it's faster to build on an existing server than to launch a new server and kill old ones). We've all heard of the big companies having the famous "push to build" button (companies like Twilio, Etsy, etc.) but it seems that they all have custom implementations of this. I'm not talking about a simple ssh-loop, clusterssh, or even an mcollective - I preferably want something with a nice simple interface that allows me to specify something like a RightScript or a Scalr script to run on a set of servers with a specific role, and it builds them sequentially. Does any one know of easy ways to get this done, or is this a candidate for a new open source project?

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• HP StorageWorks P4500 G2 Manager Management

  - by MDMarra

  According to the documentation, a management group should have an odd number of managers greater than 1. I have a four node SAN consisting of P4500 G2s. I plan on having two clusters with two nodes each in this management group, i.e.: -Managent_Group1 -Cluster1 -Node1 -Node2 -Cluster2 -Node3 -Node4 Are there any issues running standard managers on Node1, Node2, and Node3? After reading the documentation, I'm still unclear about whether or not cluster membership matters in quorum consistency, or if they don't matter at all.

  Read the article

• Transferring NS records to a new server

  - by lanemiller

  I feel like that was NOT worded well, but here is my current predicament. I recently had a GoDaddy dedicated server, and decided after their customer support failed to do anything but disappoint, to switch to Rackspace. We have 2 ns records that point to our godaddy server, and we have a few sites left on the server, that rely on it for their DNS zones, and the owners of the domains fail to respond to us. So, the question is, if I need to transfer the sites off of the OLD godaddy NS, can I point the A records from my ns1.domain.com and ns2.domain.com to match up with IP addresses of the Rackspace nameservers? OR, do I cname my NS records to match the rackspace ones? I DO know that this isn't advised, either method, but I need to get these sites moved before Godaddy tries charging another $2k for the server.

  Read the article

• Build a server in KVM linux

  - by Lai Yu-Hsuan

  I owned a linux server. Now there are several users want to build web services on it, but they require different enviroments. For convenience I give a KVM virtual machine root permission to each user. But obviously the linux server has only one IP. How can I deliver the external requests to corresponding virtual machine? (I expect it's somewhat complicated. If so I want at least some docs/websites I can start reading.)

  Read the article

• Forefront TMG 2010: Can you monitor realtime TCP connections and bandwidth on a per-user basis?

  - by user65235

  I'm just starting a trial of ForeFront TMG to use as a proxy server. I know I can get a real time activity monitor and filter on a per user basis, but would like to be able to get a real time activity monitor of all users that I can then sort by bandwidth consumed (enabling me to get a view on who the bandwidth hogs are). Does anyone know if this is possible in Forefront TMG or if a third party product is required? Thanks. JR

  Read the article

• jdbc4 CommunicationsException

  - by letronje

  I have a machine running a java app talking to a mysql instance running on the same instance. the app uses jdbc4 drivers from mysql. I keep getting com.mysql.jdbc.exceptions.jdbc4.CommunicationsException at random times. Here is the whole message. Could not open JDBC Connection for transaction; nested exception is com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: The last packet successfully received from the server was25899 milliseconds ago.The last packet sent successfully to the server was 25899 milliseconds ago, which is longer than the server configured value of 'wait_timeout'. You should consider either expiring and/or testing connection validity before use in your application, increasing the server configured values for client timeouts, or using the Connector/J connection property 'autoReconnect=true' to avoid this problem. For mysql, the value of global 'wait_timeout' and 'interactive_timeout' is set to 3600 seconds and 'connect_timeout' is set to 60 secs. the wait timeout value is much higher than the 26 secs(25899 msecs). mentioned in the exception trace. I use dbcp for connection pooling and here is spring bean config for the datasource. <bean id="dataSource" destroy-method="close" class="org.apache.commons.dbcp.BasicDataSource" > <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/db"/> <property name="username" value="xxx"/> <property name="password" value="xxx" /> <property name="poolPreparedStatements" value="false" /> <property name="maxActive" value="3" /> <property name="maxIdle" value="3" /> </bean> Any idea why this could be happening? Will using c3p0 solve the problem ?

  Read the article

• Disabling Windows Server 2008 firewall

  - by Vladimir Georgiev

  I am very stupid. I applied a windows firewall rule that blocks all tcp connection and thus kicking me out of remote desktop on a dedicated server. I managed to get into recovery via VNC, which is basically a windows xp recovery system. I have access to the physical files of the Windows Server 2008 R2 installation, but I don't know how to disable the firewall so I can reboot from recovery and connect to the W2K8 via remote desktop. Please, help.

  Read the article

• How to turn off Windows Azure's "This copy of Windows is not genuine" message?

  - by Sid

  Is there any setting/configuration item to avoid Windows Azure from printing that error on the screen or detecting it? I've put a screenshot below that shows the message when you RDP into the web role. My web role runs on Windows Azure Guest OS 1.17 (variant of Windows Server 2008 SP2) Background: I was explaining our architecture to some outside engineers (NDA'd and all) and had to demystify the webrole as they were unfamiliar with Azure. I RDP'd into the VMs running the Web Role when one of their engineers gasped "are you guys running pirated copies of Windows in the cloud?" I also noticed that within the RDP screen, the Azure machines had "This copy of Windows is not genuine" on the bottom left corner. Now obviously, Microsoft is running their own OS in their own datacenter with no influence from me. So no 'piracy' here, despite that obvious warning. However, they seemed so distracted by this ("how can it be? really? hmmm?") that we wasted more time talking about it than the actual matter at work. Like I said, they have little exposure to Azure but have value add elsewhere. I want to get rid of this so I don't have to explain this in the future. PS Microsoft: If you're going to modify Windows Server <XYZ> into Windows Azure <A.B> , you should also modify the code that verifies product integrity.

  Read the article

• illegitimate traffic from user agent Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.10) Gecko/2009042316 Firefox/3.0.10 (.NET CLR 3.5.30729)

  - by user114293

  Since the beginning of the year, I'm getting a lot of traffic with the user agent Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.0.10) Gecko/2009042316 Firefox/3.0.10 (.NET CLR 3.5.30729). My access logs show 40% - 60% from that user agent. That's strange because the user agent states a Firefox 3.0.10 browser (is anybody using that browser in 2012? Definitely not 40%-60% of visitors on a normal website). Also, the logs show that this user agent only requested the HTML document and no referenced assets like images, css, js files. I checked the IPs of those requests (with that UA). It's coming from all over the world. I recognized that those IPs sometimes have a mobile user agent. So my suspicion is a mobile app that is doing a lot of "spider requests" - but if that would be the case than other web sites should have the same problem. That's actually my question: Does anybody experience same/similar problems?

  Read the article

• fast opening and closing connection with a specific port

  - by michale

  We have a Main application named "Trevor" installed in 2008R2 machine named "TEAMER12" which is slow now. One more application named "TVS" also running in and found there were many connections per second occurring to port 5009. netstat tool mentions that some fast connection open/close seen for port 5009 So first it will be listening mode like shown below TCP 0.0.0.0:5009 TEAMER12:0 LISTENING then establishes connection like TCP 127.0.0.1:5009 TEAMER12:49519 ESTABLISHED TCP 127.0.0.1:5009 TEAMER12:60903 ESTABLISHED After that iwill become TIME_WAIT and i could see several entries like shown below TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT after that it will establish connection like TCP 127.0.0.1:60903 TEAMER12:5009 ESTABLISHED TCP 127.0.0.1:64181 TEAMER12:microsoft-ds ESTABLISHED again it will go several entries like TIME_WAIT TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT Finally it will establish like this TCP 172.26.127.40:139 TEAMER12:0 LISTENING TCP 172.26.127.42:139 TEAMER12:0 LISTENING TCP 172.26.127.42:5009 TEAMER12:64445 ESTABLISHED TCP 172.26.127.42:64445 TEAMER12:5009 ESTABLISHED Can any body tell me whats the reason behind why many connections per second occurring to port 5009 and why application slow?

  Read the article

• In Varnish, is it normal for the number of freed bytes to be 60% of those allocated?

  - by user331397

  I have an installation of Varnish 3.02 on an Amazon EC2 Medium Linux instance in front of two relatively low-traffic websites. After an uptime of 2 hours, there are 3400 objects in the cache. Using varnishstat, I checked the variables SMA.s0.c_bytes and SMA.s0.c_freed, which I assume correspond to the total number of bytes allocated since startup and the number freed, respectively. No objects should have had time to expire during these two hours, but still about 60% of the memory allocated since startup (330MB out of 560MB) has already been freed. Do you know if this is normal? If not, do you know what kind of configuration could be wrong?

  Read the article

• Move an existing RAID 5 array from Ubuntu to Gentoo

  - by Cocoabean

  I have a 64-bit Ubuntu machine with a 4-disk RAID 5 using software raid (md). I've been able to boot an Ubuntu LiveCD and recognize the array with a simple mdadm -A /dev/md0. It was easy to mount after that and nothing had to rebuild. I'm installing Gentoo on this box now (multi-boot, non-RAID root partition) and I have md auto-detect turned on in the kernel. When I boot Gentoo I get: "invalid superblock magic on sdd" for each of the drives in the array. I boot back to Ubuntu and they mount no problem. I tried copying the mdadm.conf that works in Ubuntu to Gentoo, and then ran mdadm -A /dev/md0 but it reports that there is no array named md0. I don't want to lose data (obviously) and I don't want to have to let the RAID rebuild every time I switch between OSes. Any help is appreciated. Both are using mdadm 3.1.4 Both are running 64-bit kernels. mdadm -D /dev/md0 from Ubuntu yields: http://pastebin.com/5gj2QNkV UPDATE: After rebooting I noticed that it still complains about invalid blocks, but cat /proc/mdstat shows an inactive /dev/md127 with the same disks as my raid. I want to mount it but I don't want to get stuck waiting for a rebuild or destroying it inadvertently. mdadm -D /dev/md127 Here is pastebin of mdadm -D /dev/md127 on gentoo: http://pastebin.com/gDCWn0Rn UPDATE II: dmesg output about 'invalid raid superblocks' http://paste.ubuntu.com/885471/ fdisk -l from Ubuntu, /dev/md0 does not have any partitions but I do have it mounted and accessible: http://paste.ubuntu.com/885475/

  Read the article

• Nano suddenly putting in weird characters when I type

  - by Cocorico

  I am using a shell and editing a file in nano (similar to pico). A short while ago, it started doing this thing where if I type: $query = "select" * from topics where id='' "; and then I hit Backspace and try to stick the letter 'a' into the id='' part, it changes it to: $query = "select * from koala_topics where id='a='' "; and the cursor jumps around to a few spaces before. Also if I type print At the start of a new line, and then I think "Oh I should have added a tab" and I go back and try to add a tab, it adds a tab AND 2 spaces, and if I put the cursor through the word print, it turns into printnt. Some other weird things have happened too. I uninstalled nano using yum (which is how I installed it), and then re-installed it, thinking that would get me clean preferences (in case that was the problem) but it doesn't fix it.

  Read the article

• Fujitsu Siemens V6535 laptop doesn't wake up - crash when going into standby?

  - by marc

  I'm having trouble with my laptop (Fujitsu Siemens model V6535). It runs Windows 7, and after I upgraded from Vista I've noticed something that makes me really angry. When my laptop goes into Standby, the power LED changes to red and starts blinking (standby mode). When I push the power button to wake it up it, the blinking LED changes to green but nothing else happens. Nothing on the display, no HDD sound. When I press the power button for a few seconds and then try turn it on again, it doesn't display anything. I have to unplug the charger, shut it off, and power it on again without the power cable. Then it starts working. A few days ago I upgraded the BIOS to the newest version, but it doesn't help. Does anyone have any idea what can be wrong?

  Read the article

• what does it mean for MalwareBytes to find malicious registry keys but nothing else?

  - by EndangeringSpecies

  I have a machine that is obviously infected, and when I ran MalwareBytes it told me that it found some "malicious" registry keys (surprisingly enough these contained file path to currently non-existent javascript files). But, that's it. Full scan did not uncover any malicious files, or malicious hidden processes in memory. Like, maybe the (hidden?) process that for whatever reason periodically injects keystrokes (hotkeys?) into whatever currently open window. Then on another, not obviously infected, machine it found a "malware.trace" registry key but again no files or processes etc. How does this jive with people's experience with MalwareBytes? Does it usually find registry key symptoms of an infection but nothing else? Or is it a common thing to have no infection but some malicious registry keys in place anyway?

  Read the article

• Clonezilla multiple disks restore to single disk

  - by Farseeker

  I have a clonezilla image from a machine that had 3 seperate disks (one partition per disk). I want to know if I can restore that image to another computer that has a hard drive that's much larger than the original, but only has one drive. Clonezilla is stating that it can't do this automatically, and perhaps I should try cnvt-ocs-dev but I've no idea what that means (Google is less than forthcoming with information about it too). Ok so I found out what cnvt-ocs-dev is, and that allows me to move source/destination targets between physical disks, but it doesn't seem to be able to move the partition as well.

  Read the article

• Windows 7 - All Icons Missing, Explorer Progress Bar Never Finishes, Libraries Gone

  - by Alex

  since yesterday i've had three issues which all arose at the same time. windows 7 x64, i7 2.8ghz 12gb ddr3 1 - my libraries, favorites, drives are missing...basically the entire sidebar is gone. http://i.imgur.com/m8pRQ.png. yet when i open a dialog, my libraries and drives are back to normal ONLY for the dialog. i tried Restore Default Libraries. it works one time, but when i open libraries again i go back to the empty mess. restarting the computer temporarily fixes the problem. 2 - in the explorer window that's showing libraries, when i navigate to a certain folder i get an unending progress bar (the kind that turns the address bar green). yesterday when the problem started, i was saving a file to this folder. the program writing the file crashed during the write and i believe that's what caused the problem. i have sugarsync backing up that folder and when i restarted the computer sugarsync informed me that its database was corrupted, so i had to uninstall and reinstall the software. 3 - icons are missing. the Rebuild Icon Cache did not fix this. http://i.imgur.com/r9pgo.png restarting the computer temporarily fixes these problems, but when i open the directory with the initial write problem, everything stops working. edit: i should note that i did a chkdsk /f and it repaired problems. i also did the thing that verifies then restores windows files (can't remember the command now), which reported that everything was normal.

  Read the article

• VPN stuck on Verifying Username and Password

  - by user2791

  I'm building a new machine and everything is working correctly, except that I can't log on to my VPN. It hangs at the "Verifying username and password..." step, then returns after about 30 seconds claiming Error 721. I have another machine sitting next to this one with the VPN connection configured exactly the same, connecting just fine over the same wifi network, so I'm convinced that there is no server or firewall problem. The VPN works fine. This machine simply can't connect to it given the correct credentials and configuration. Any suggestions?

  Read the article

• Windows XP periodically disconnects, reconnects; Windows 7 doesn't

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

  Read the article

• Connectivity good between VMs, but no connectivity between host and VM

  - by Greg Sansom

  I have a strange situation where connectivity (ie ping, access shared folders and services) is fine between virtual machines, but not between the host and the virtuals. I've been using Hyper-V almost every day for years and have never had a problem like this. Note the following: The host machine and all virtuals are running Windows Server 2008 r1. All machines can connect to the web, and the gateway router. Subnet mask and gateway reported in ipconfig are identical for all machines. I can access virtuals via the Hyper-V snap-in only. Doea anyone have suggestions about what might be wrong, or what diagnostic steps I can take?

  Read the article

• How to make IE 9 stop reading all the fonts every time?

  - by Mehrdad

  Process Monitor showed me that IE 9 accesses every time it loads on my system, which makes it have a 1- to 2-second delay every time it loads. (I tested this by removing my fonts -- it loaded much more quickly.) It gets a little annoying, because it's the best handler I have for MHT files, so I don't want to switch to something else. Is there any way to make it avoid doing that? (The "Hide Fonts" feature in Windows 7 doesn't work.)

  Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >