Daily Archives

Articles indexed Saturday June 16 2012

Page 5/13 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Can't find a wireless access point's IP address after changing router IP/LAN settings

  - by flagg19

  I have a modem/router, Netgear DG834, and a wireless access point (AP), Netgear WG602. The AP is directly connected to the router. My old working configuration was: Router IP address : 192.168.0.1 Access point IP address: 192.168.0.10 My new configuration is: Router IP address : 192.168.1.1 Access point IP address: ???.???.???.??? I changed my router's IP address/LAN settings to set up a VPN with another Netgear router that had the same LAN configuration. The wireless network is still up and perfectly working, but I can't find the AP's IP address. I've tried broadcast ping but the AP won't respond. I looked at the router "attached devices", but it's not there. I've played around with Nmap and arp request but the AP is totally invisible. I can fix it by resetting it to factory settings, but I'm very interested in learning more about this problem. I'm also interested in network security and this fact of having an invisible AP well, it's something I'd like to understand.

  Read the article

• What changed between Excel 2007 and 2010 that is causing my copied worksheet save to fail?

  - by snorehorse

  When I do this in Excel 2010 this fails, but works in Excel 2007: Create a new workbook and insert an image onto a worksheet, or get a preexisting worksheet with an image. Copy the worksheet into a new workbook by clicking the worksheet tab and clicking Move Or Copy and then choosing (new workbook) as the destination. Close the source workbook. Attempt to save the new workbook. The message is: "Errors were detected while saving 'myfilepathhere.xlsx'. Microsoft Excel may be able to save the file b removing or repairing some features. To make the repairs in a new file, click Continue. To cancel saving the file, click Cancel". Clicking continue brings up another file dialog window followed by more repair errors. It seems behind the scenes it is looking to the source workbook when it tries to save the image in the new destination workbook. No useful error message, of course, thanks microsoft. But this problem never happened in Excel 2007. The reason why I am closing the source notebook before the save, is because I don't need the end user to see it after I programmatically pull a coversheet (with the image) from it, in an interop app. Thanks for any help. Update: I don't encounter this problem if I open the source workbook as "Read Only" (I do this programmatically using Excel Interop).

  Read the article

• Add domain user as local admin in Windows 7 using VPN to connect to domain

  - by kev

  I am rebuilding my work computer from scratch and need to add my domain user as a local admin on my computer. I have successfully added my PC to the domain, but I cannot add my domain user account to the local admins. I have tried to do the following: Connect to the work domain using a Windows VPN Add my computer to the work domain Start right click on Computer Manage - go to Users and Groups right click on Administrators group and add my domain user The problem is that after adding my domain user to the Administrators group, I don't see my domain user under the Local Users group. When I try to log on as my domain user I get the following error message: There are currently no logon servers available to service the logon request Any ideas?

  Read the article

• How to Reset Your Forgotten Domain Admin Password on Server 2008 R2

  - by Taylor Gibb

  Forgetting your password is always a pain, but luckily there’s an easy way to reset your Domain Administrator password. All you need is a copy of the Windows Server 2008 R2 installation disk and one simple command line trick. HTG Explains: What Is Windows RT and What Does It Mean To Me? HTG Explains: How Windows 8′s Secure Boot Feature Works & What It Means for Linux Hack Your Kindle for Easy Font Customization

  Read the article

• East Coast Oracle Users Group Conference...

  - by noreply(at)blogger.com (Thomas Kyte)

  I'll be speaking at the East Coast Oracle Users Group Conference held in North Carolina on October 16th-18th.  It is always nice to be able to stay in my own timezone for a change!There are opportunities to not only attend the conference but also to speak - they are still accepting abstracts for presentations until June 21st.  If you have done anything interesting (you have), please consider speaking out about it.  Others will be interested.  You never know how it will go unless you try!Hope to see you there!

  Read the article

• How to start embedded development for developing a handheld game console?

  - by Quakeboy

  I work as a iPhone app developer now, so I know a bit of c, c++ and objective c. Also have fiddled with Java and many other. All of them have been just high level application/games development. My final goal is to make a handheld game console. More like a home made NES/SNES handheld console or even an Atari. I have found out about RaspberryPI and Arduino. But I need more information about how to approach this. 1) How Do I learn to pick the best board/cpu/controller/GPU/LCD screen/LCD controller etc? 2) Will learning to make a NES emulator first help me understand this field? If so are there any tutorials?

  Read the article

• How to access functions in extended classes efficiently?

  - by nischayn22

  In PHP I have classes as below class Animal { //some vars public function printname(){ echo $this->name; } } class AnimalMySql extends Animal { static public function getTableFields(){ return array(); } } class AnimalPostgreSql extends Animal { static public function getTableFields(){ return array(); } } Now I have an object $lion = new Animal(); and I want to do if($store == mysql) //getTableFields from class AnimalMySql else //getTableFields form class AnimalPostgreSql I am new to OOP and not sure what is the best way to call the method from the specific class P.S. Please leave a note with the answer to explain the efficiency of the approach

  Read the article

• Passing class names or objects?

  - by nischayn22

  I have a switch statement switch ( $id ) { case 'abc': return 'Animal'; case 'xyz': return 'Human'; //many more } I am returning class names,and use them to call some of their static functions using call_user_func(). Instead I can also create a object of that class, return that and then call the static function from that object as $object::method($param) switch ( $id ) { case 'abc': return new Animal; case 'xyz': return new Human; //many more } Which way is efficient? To make this question broader : I have classes that have mostly all static methods right now, putting them into classes is kind of a grouping idea here (for example the DB table structure of Animal is given by class Animal and so for Human class). I need to access many functions from these classes so the switch needs to give me access to the class

  Read the article

• How to run CLI commands from the launcher?

  - by user50849

  I press ALT+F2 key on my keyboard, and get the launcher HUD up. From there I enter a command as I would in a shell, specifically vlc ~/Music/* -Z. If done from a shell, vlc starts and begins to play music. However, when done from the launcher, VLC replies: File reading failed: VLC could not open the file "/home/[username]/Music/*". (No such file or directory) user Your input can't be opened: VLC is unable to open the MRL 'file:///home/[username]/Music/%2A'. Check the log for details. I can't quite figure out what the difference is.

  Read the article

• 12.04 Dell GX260 resolution for 82845G/GL will not go greater than 1024x768

  - by Steve M

  I am a newbie to Linux and have installed 12.04 on to an old Dell GX260, I was hoping that I could slowly extract myself from Microsoft - but unless I can fix this simplest of problems I am thinking that this version of Linux is not ready for me yet!! I have read various posts but none seem to match, I believe the driver is installed, but under displays the maximum allowed in the drop down box is 1024x768 (4:3) display is unknown and detect displays does nothing. I have loaded all updates available but still no fix. xrandr shows: VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 xrandr --addmode VGA1 1360x768 cannot find mode "1360x768" anything above 1024x768 can not be found, but then I could be doing this out of step!!

  Read the article

• latest intel graphics driver?

  - by Anwar Shah

  I have Intel Graphics Card, which have model number GM965. It is on a Notebook, (Lenovo 3000 Y410). My Ubuntu Installation worked good until I upgraded to 12.04. It was a fresh install. The Graphics performance is poor compared to Natty, Oneiric. In the details tab of System Settings, Graphics driver is shown as "Unknown". I have upgraded the xserver-xorg-video-intel package to version 2.19.. from 2.17. But still same. So, My question is How can I install latest Intel graphics driver for my Chipset? or Is there any other method to fix the problem with graphics.

  Read the article

• What is the default permission for /var/www?

  - by itsols

  After upgrading to 12.04, I had to reinstall the LAMP stack. Then I brought all my www project folders from a pen drive to the /var/www folder (using sudo nautilus, and dragging the files in there). Now I cannot make any changes to the files/directories within /var/www. Perhaps this changed with the backup copies I dragged in there. I'd like to know what the default permissions for the /var/www folder are. I don't want to just change the permissions and make my system abnormal and working. Rather I'd like to get it to the correct state that is meant to work.

  Read the article

• How do I install lubuntu? (kernel panic)

  - by melvincv

  Please help me install Lubuntu 12.04 i386 on an old computer. I select the "Try Lubuntu without installing" and it crashes with a kernel panic. Rarely I do get to the live OS, but soon the display goes blank. The messages log gives me '[drm] ERROR GPU hung/wedged' The specs are: Pentium 4 2.4GHz 1GB DDR RAM 40GB PATA HDD Intel 845GL chipset (8MB framebuffer, 64MB shared system memory set in the BIOS)

  Read the article

• Wireless problems on HP

  - by Sat93

  I'm not able to enable Wireless using the hardware switch on my HP ProBook4430s. Because of this the Enable Wireless option is greyd out and I cannot enable it. The greyd out option can be seen in the screenshot below. The results of iwconfig for my system are as follows, lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. Also I tried to do the following, sudo ifconfig wlan0 up but I got an error as below, SIOCSIFFLAGS: Operation not possible due to RF-kill Also the result of sudo rfkill list all for my system is as follows, 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no How do I fix this problem? Thanku!

  Read the article

• solve a partition misalignment?

  - by learner

  I have a new Dell XPS laptop which had Windows 7 installed in it. It also had a default extra partition for "Dell Utility". I installed Ubuntu in it on an Extended Partition along with windows and specified the logical partitions myself (for /,/home and swap). Now when I open Disk Utility , it shows this "Partition misaligned by 512 bytes" error for the Dell Utility partition and "Partition misaligned by 1024 bytes" for the entire Extended partition where Ubuntu is installed. Deleting the extended partition and re-installing Ubuntu may solve the problem of misalignment in the extended partition. But how about the Dell Utility partition? If I re-install Windows 7 Dell Utility wouldn't be a part of the re-install. So that may not solve it either. How do I fix this? Note: The extended partition I made contains an NTFS logical partition for holding data accessible by both OSes(basically a personal data partition). EDIT: I deleted all my Ubuntu partitions and re-installed Ubuntu like before,this time making them partitions with GParted via LiveCD. Now the only problem is that there is a misalignment in the Dell Utility partition. The other misalignment got fixed. Now how do I get rid of that issue?

  Read the article

• Cinnamon install problem ubuntu 12.04

  - by Kin.

  I was following the How do I install the Cinnamon Desktop?, but when i install, it like this locahost@locahost:~$ sudo apt-get install cinnamon Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: cinnamon : Depends: libgjs0- E: Unable to correct problems, you have held broken packages. How can i install the libgjs0- package?

  Read the article

• Ubutnu 12.04 mdadm inactive

  - by user32274

  For a while now, my RAID 5 has ceased to work. Everytime I tried "madm --detail /dev/md127", its states all the drive and drive info, but that two of the drives have been removed. After some restarts, doing the same thing, i am getting /dev/md127 does not appear to be active. When I go into DiskUtil, I can see all 6 Hard Drives healthy and present, and i can see the Raid 5 at the bottom under Multi-disk Devices. However, the Raid says 0.0kb, and is not active. Please help and let me know how to proceed from here. I would really like to avoid rebuilding the RAID, especially because all 6 drives seem to be healthy and present. Thanks so much.

  Read the article

• Downloading error "Could not retrieve the required disk image "

  - by Freed Ahmad

  When I try to download Ubuntu 12.04 using the Windows installer (Wubi) through a proxy server which requires proxy authentication, after I choose the Ubuntu installation size, username and password, when I click the Install button, I get this error: An error occurred: Could not retrieve the required disk image files For more information, please see the log file: c:\users\(myusername)\appdata\local\temp\wubi-12.04-rev266.log The log file says: proxy authentication error How can I solve this problem?

  Read the article

• Does anyone use 12.04 with HD 6950?

  - by Midori

  Back when I first tried to switch from Windows to Ubuntu (6-7 months ago) I had several graphics related problems. The VGA was overheating, graphic glitches, video playing issues, slow/choppy window movements etc. After 2-3 reinstalls, hours of playing with different drivers/settings I decided to return to Windows :\ Now I want to give it another shot. But before I start to format, partitioning, backup and other time consuming stuff I wanted to ask if anyone using the 12.04 with HD 6950. Can I utilize the full potential of it, or the drivers are still not good enough? I know that Linux isn't meant to play games in the first place, but the games I playing (SC2, BLC, HoN, DotA 2) are working with wine as far as I know (or aren't?) and I can't find any reason not to switch from Windows if I can utilize the full potential of my config in Ubuntu. So anyone who got experiences with this VGA in Ubuntu please reply. Thanks in advance :)

  Read the article

• Wireless not working with an Atheros AR9285

  - by Neeraj

  I recently installed Ubuntu 12.04 and found my wireless card is not detected by OS. I tired to detect it by network manager but still it is not get output of the required command: toor@Linux:~$ sudo lshw -class network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:9e:22:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=124.123.227.84 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:44 memory:f2400000-f243ffff ioport:2000(size=128) *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f2500000-f250ffff and toor@Linux:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no Please let me know what more info is required to resolve it.

  Read the article

• How to get Cinnamon working in Virtualbox?

  - by kavoura

  I installed Ubuntu 11.10 (32-bit) in VirtualBox 4.1.8. I wanted to install Cinnamon, so I did and I have the option to choose it from the login screen, as well as GNOME options. If I choose Ubuntu I get Unity, which works fine. GNOME also works. But when I choose Cinnamon, the screen goes black and nothing responds and I have to reset the virtual machine. I have already installed Ubuntu 11.10 (64-bit) onto the PC in a separate partition (currently running 10.10 but trying out 11.10) and in that Cinnamon works perfectly. In VirtualBox I have 3D settings enabled and gave the virtual machine 128 MB graphics RAM, and 1024 MB system RAM. What settings should I change or what should I do to get Cinnamon working in Ubuntu in VirtualBox? I have also tried doing it in LinuxMint 12, but I get the same problem, just a black screen when selecting Cinnamon. So are Cinnamon and VirtualBox incompatible?

  Read the article

• How do I prevent the Sleep button from locking the screen

  - by elmicha

  My keyboard has a Sleep button. I defined a shortcut in System Settings, Keyboard Shortcuts own settings (or similar), so that the Sleep buttons runs a script. That works. But since my upgrade to Oneiric, something also locks the screen (in the same way the screen is locked when I press Ctrl+Alt+L). Can I disable that behaviour? What's the name of that lock screen? I tried hiding gnome-screensaver and /etc/acpi/ and I looked in gconf-editor /apps/gnome-power-manager/buttons. I didn't find anything related in dconf-editor.

  Read the article

• Mount encrypted volumes from command line?

  - by cha

  If I have an encrypted external disk (or an internal disk that is not in fstab), I see an entry for it in Nautilus -- with an entry like "X GB Encrypted Volume". I can click on this volume, and am prompted for a password to decrypt and mount the device. But how do I do this from the command line? This wiki page, and other docs I can find, only refer to GUI methods of decrypting the device; but this won't do in the context of headless servers or SSH logins. Is there a simple way to get devices to mount to automatic locations in "/media" just like they would with the GUI? (I'm not asking about encrypted home directories -- I'm aware of ecryptfs-mount-private. This question is about additional encrypted volumes.)

  Read the article

• What does the SEO market look like? [closed]

  - by TheEconomist

  I'm an economist (aspiring economist, if we are being technical) and my curiousity has been recently piqued by search engine optimization services. I had the following questions. 1) What industries most widely use search engine optimization services? 2) Is it small business or big firms that use SEO services typically? 3) What is SEO pricing typically dependent upon and how much is it on average? 4) Do SEO services really increase traffic? Is there a dataset I can get a hold of for this sort of thing? I am not looking for answers to the questions necessarily. Although answers would help, a nudge in the right direction is more than sufficient, and greatly appreciated. Thank you!

  Read the article

• Tracking Outgoing Links With Google Analytics Events

  - by the_archer

  I've been trying to track clicks on external links on my website using the events tracking method. So I've got my Google Analytics code setup before body ends as shown below (note: quotes have been entitied by blogger, but it works fine): <script type='text/javascript'> var _gaq = _gaq || []; _gaq.push([&#39;_setAccount&#39;, &#39;UA-XXXXXXX-X#39;]); _gaq.push([&#39;_trackPageview&#39;]); (function() { var ga = document.createElement(&#39;script&#39;); ga.type = &#39;text/javascript&#39;; ga.async = true; ga.src = (&#39;https:&#39; == document.location.protocol ? &#39;https://ssl&#39; : &#39;http://www&#39;) + &#39;.google-analytics.com/ga.js&#39;; var s = document.getElementsByTagName(&#39;script&#39;)[0]; s.parentNode.insertBefore(ga, s); })(); </script> Now I wanted to track a link on the addthis.com follow widget. So there is a link of the type below to which following instructions from here I added the onclick event. <a addthis:url='http://feeds.feedburner.com/myfeedburnerlurl' onClick="_gaq.push(['_trackEvent', 'Subscription Clicks', 'RSS']);" class='addthis_button_rss_follow'/> I clicked on it a couple of times, left it for over a day now, but nothing shows up in google analytics events. It just says zero events. Here's a screenshot of the events page on GA: Could anybody help me? Am I doing anything wrong?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >