Monthly Archives

Articles indexed in April 2012

Page 7/252 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• RAID6 mdraid -> LVM -> EXT4 root with GRUB2?

  - by Rotonen

  2012-03-31 Debian Wheezy daily build in VirtualBox 4.1.2, 6 disk devices. My steps to reproduce so far: Setup one partition, using the entire disk, as a physical volume for RAID, per disk Setup a single RAID6 mdraid array out of all of those Use the resulting md0 as the only physical volume for the volume group Setup your logical volumes, filesystems and mount points as you wish Install your system Both / and /boot will be in this stack. I've chosen EXT4 as my filesystem for this setup. I can get as far as GRUB2 rescue console, which can see the mdraid, the volume group and the LVM logical volumes (all named appropriately on all levels) on it, but I cannot ls the filesystem contents of any of those and I cannot boot from them. As far as I can see from the documentation the version of GRUB2 shipped there should handle all of this gracefully. http://packages.debian.org/wheezy/grub-pc (1.99-17 at the time of writing.) It is loading the ext2, raid, raid6rec, dosmbr (this one is in the list of modules once per disk) and lvm modules according to the generated grub.cfg file. Also it is defining the list of modules to be loaded twice in the generated grub.cfg file and according to quick Googling around this seems to be the norm and OK for GRUB2. How to get further by getting GRUB2 to actually be able to read the content of the filesystems and boot the system? What am I wrong about in my assumptions of functionality here? EDIT (2012-04-01) My generated grub.cfg: http://pastie.org/3708436 It seems it first makes my /usr logical volume the root and that might be source of the failure? A grub-mkconfig bug? Or is it supposed to get access to stuff from /usr before / and /boot? /boot is on / for me - no separate boot logical volume.

  Read the article

• How to either completely remove SQL Server 2008 R2 Installation or repair it?

  - by Nico

  I've installed MSSQL server correctly, then I took some wrong turns and I'm now left in a pretty undesirable state. I wanted to change the server instance to another drive, so I uninstalled SQL server and all of it's features from the Programs and Features control panel. Now when I tried to install a new instance, I got a few errors, but it still installed most of them: Then I tried to run a repair, which I figured would fix things, but it throws an exception about not being able to read something from the CD (tried more than once always the same exception) Error 1316.A network error occurred while attempting to read from the file R:\1033_ENU_LP\x64\setup\SSCERuntime_x86-enu.msi , and it fails to repair a few of the features: And I don't have the server instance installed either. So I'm left with no MSSQLMS, no server instance, and no happiness. What would be the best course of action here?

  Read the article

• APC UPS replace battery light and apcupsd reporting "replace battery"

  - by mgjk

  We have an APC Smart UPS 1500. The "Replace Battery" light is on, and apcupsd reports: Emergency! Batteries have failed on UPS xxxx. Change them NOW However, from this article, http://sturgeon.apcc.com/kbasewb2.nsf/for+external/f39c4312fcaf7b948525679a005ebb78?OpenDocument it seems that it's not so clear that the UPS battery needs to be replaced. Stranger, according to the information on the UPS, an 11 minute runtime at 42.9% load running at 27.7V isn't so bad. Any thoughts about what to try next? We're a non-profit, money is an object. It would be a shame to replace a battery with a year or so left in it. # apcaccess status APC : 001,041,1017 DATE : Thu Mar 29 13:01:41 EDT 2012 HOSTNAME : oreilly2 VERSION : 3.14.6 (16 May 2009) debian UPSNAME : xxxx CABLE : Custom Cable Smart MODEL : Smart-UPS 1500 UPSMODE : Stand Alone STARTTIME: Thu Mar 29 12:57:30 EDT 2012 STATUS : ONLINE LINEV : 112.3 Volts LOADPCT : 42.9 Percent Load Capacity BCHARGE : 100.0 Percent TIMELEFT : 11.0 Minutes MBATTCHG : 5 Percent MINTIMEL : 3 Minutes MAXTIME : 0 Seconds OUTPUTV : 112.3 Volts SENSE : High DWAKE : -01 Seconds DSHUTD : 090 Seconds LOTRANS : 106.0 Volts HITRANS : 127.0 Volts RETPCT : 000.0 Percent ITEMP : 23.8 C Internal ALARMDEL : Always BATTV : 27.7 Volts LINEFREQ : 60.0 Hz LASTXFER : No transfers since turnon NUMXFERS : 0 TONBATT : 0 seconds CUMONBATT: 0 seconds XOFFBATT : N/A SELFTEST : NO STATFLAG : 0x07000008 Status Flag SERIALNO : AS0603298896 BATTDATE : 2006-01-14 NOMOUTV : 120 Volts NOMBATTV : 24.0 Volts FIRMWARE : 601.3.D USB FW:1.5 APCMODEL : Smart-UPS 1500 END APC : Thu Mar 29 13:02:12 EDT 2012 Error when running upstest You are using a SMART cable type, so I'm entering SMART test mode mode.type = USB_UPS Setting up the port ... Hello, this is the apcupsd Cable Test program. This part of apctest is for testing Smart UPSes. Please select the function you want to perform. 1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit Select function number: 2 First ensure that we have a good link and that the UPS is functionning normally. Simulating UPSlinkCheck ... YWrote: Y Got: getline failed. Apparently the link is not up. Giving up.

  Read the article

• Software Raid 10 on VirtualBox?

  - by user791022

  I want to learn how to use Software Raid 10, is it possible to use VirtualBox by adding four storage images? This is my plan: 4x 100mb partitions (1 on each drive) configured as a raid 1 for /boot in ext3. Then with the remaining space on each drive, setup a software raid partition and configure it to to LVM and raid 10. In the LVM, set up a 4gb swap partition and the remaining space as the root partition ( / ) as ext3.

  Read the article

• Permissions nightmare - tried all I know

  - by Ben

  Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

  Read the article

• Oracle Database Recovery Problem

  - by Palani

  I am very new to Oracle, and trying to restore a oracle 8i database on win 2000 server. I have one week old database backup (backup taken with exp command), and i want to restore it now. Now I am unable to login through sqlplus (got shutdown in progress error) I have a backup and i want to restore it, but oracle is not starting at all, and 'imp' command is failing. I started sqlplus / as sysdba and following is the log of what i am trying to do. Can some one guide me further. SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> shutdown immediate; ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup mount; ORACLE instance started. Total System Global Area 143423516 bytes Fixed Size 75804 bytes Variable Size 58105856 bytes Database Buffers 85164032 bytes Redo Buffers 77824 bytes Database mounted. SQL> alter database open; alter database open * ERROR at line 1: ORA-01589: must use RESETLOGS or NORESETLOGS option for database open SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01245: offline file 1 will be lost if RESETLOGS is done ORA-01110: data file 1: 'C:\ORACLE\ORADATA\ABCD\SYSTEM01.DBF'

  Read the article

• FreeBSD rc.d script doesn't work when starting up

  - by kastermester

  I am trying to write a rc.d script to startup the fastcgi-mono-server4 on FreeBSD when the computer starts up - in order to run it with nginx. The script works when I execute it while being logged in on the server - but when booting I get the following message: eval: -applications=192.168.50.133:/:/usr/local/www/nginx: not found The script looks as follows: #!/bin/sh # PROVIDE: monofcgid # REQUIRE: LOGIN nginx # KEYWORD: shutdown . /etc/rc.subr name="monofcgid" rcvar="monofcgid_enable" stop_cmd="${name}_stop" start_cmd="${name}_start" start_precmd="${name}_prestart" start_postcmd="${name}_poststart" stop_postcmd="${name}_poststop" command=$(which fastcgi-mono-server4) apps="192.168.50.133:/:/usr/local/www/nginx" pidfile="/var/run/${name}.pid" monofcgid_prestart() { if [ -f $pidfile ]; then echo "monofcgid is already running." exit 0 fi } monofcgid_start() { echo "Starting monofcgid." ${command} -applications=${apps} -socket=tcp:127.0.0.1:9000 & } monofcgid_poststart() { MONOSERVER_PID=$(ps ax | grep mono/4.0/fastcgi-m | grep -v grep | awk '{print $1}') if [ -f $pidfile ]; then rm $pidfile fi if [ -n $MONOSERVER_PID ]; then echo $MONOSERVER_PID > $pidfile fi } monofcgid_stop() { if [ -f $pidfile ]; then echo "Stopping monofcgid." kill $(cat $pidfile) echo "Stopped monofcgid." else echo "monofcgid is not running." exit 0 fi } monofcgid_poststop() { rm $pidfile } load_rc_config $name run_rc_command "$1" In case it is not already super clear, I am fairly new to both FreeBSD and sh scripts, so I'm kind of prepared for some obvious little detail I overlooked. I would very much like to know exactly why this is failing and how to solve it, but also if anyone has a better way of accomplishing this, then I am all open to ideas.

  Read the article

• Recommended Free DNS hosting for my webserve on a dynamic IP? [closed]

  - by JSchwartz

  I have finished a webserver project (for school) and the professor wants to be able to "test it" from home whenever he is free - this means I need to provide his with the URL to my webserver (which is fine). The only issue is that my IP-Address is dynamic (changes almost everyday) and I would rather not have to email him everytime - nor do I want him to try when it isn't working ... So I was looking into alternative solutions like DNS hosting (I hope that is the right terminology), so I could provide something static for him to connect to ... problem is I have never done this before... Are there any recommeneded free ones? Does Google or someone provide something good? I found http://www.no-ip.com/ which seems like it does what I want... Any feedback would be appreciated. Thanks,

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• Dealing with employees that use Hotspots? [closed]

  - by javasocute

  Recently a consultant revealed to me and my superiors that a particular department in my company had a tremendous decline in productivity over the past year. This department happened to mostly work with laptops and tablets and thus had wireless. Our barracuda did not display any vast amounts of internet entertainment and so I was initially puzzled by his statement. However he explained that more and more employees are using "hotspots" that when not broadcasted, become invisible to our network. So basically these people could connect to hotspots and watch youtube all day and we would never know it. The consultant also said that this was becoming an issue for many companies. So my question is, how can I detect invisible hotspots? I was browsing google and there are several different programs that can scan for such access points. But I am hoping to get a recommendation from the serverfault community. Thank you.

  Read the article

• How large administrators team should be? [closed]

  - by Artyom

  I'm trying to find an answer about how many server administrators/technicians are required to run a server farm with 7/24 availability of let's 10, 100, 1000 Linux servers? Are there any studies for this? Edit I was not expected this question to be closed. There are lots of studies about for example software development where from "lines of code" you can approximate the software development cost (COCOMO), so I was searching for something similar in administration. Note, I'm 100% understand that it is not a straightforward or easy to answer question, but it is a real question...

  Read the article

• Recover NTFS data from a ZFS pool that was exposed as an iSCSI target

  - by David

  This was me being stupid and the data is by no means critical and is now a learning experience first, time saver second. I set up a 100GB iSCSI target via the bare bone instructions in napp-it. It's a volume LU. I then had my Windows 7 machine connect to the iSCSI target, formatted it to NTFS, and tested the performance of it with some large iso file transfers. I then unmapped the drive, reconnected to the target, and was forced to format to NTFS again. It was then I realized the files I had transferred only existed on the iSCSI target. I threw a little fit and then went about my business. When I was cleaning up my experiment I noticed in this screen: http://imgur.com/1xlcu.jpg That is my experimental target tank/iSCSI and it still has a lot of data in it. Assuming my isos are still in this pool how would I go about recovering them? While writing this I used GetDataBackup for NTFS from www.runtime.org. And while it found two previous NTFS partitions there was no data.

  Read the article

• How do I determine if my server is AMT capable for remotely turning on or rebooting a frozen computer

  - by RDK45

  I just finished reading the subject post (http://superuser.com/questions/319859/remotely-turning-on-or-rebooting-a-frozen-computer) and have further questions. I very interested in remote access to my server, in particular restarting it when it is in a stalled or blue-screen state.. How can I determine if my server is AMT enabled? It has a GIGABYTE GA-Z68MA-D2H-B3 Motherboard and Intel Core i5-2500K CPU. Thanks....RDK45

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• Computer crashes and freezes a lot

  - by Gigili

  My computer crashes like it freezes sometimes but sometimes it jumps to a black screen which I can do nothing about other than restart. I tested if it has anything to do with the programs I normally run or with the ones I installed, but it's a long time I have the problem and I think it also happened in the beginning that I bought this computer. To make sure, I normally run skype and Spiral Knights and some animation softwares like Flash. The specs are: Nvidia geforce gtx 560 evga Asus p8H67-m evo motherboard 16 gb ram Intel i7 What can I do about it? What issue is more probable to cause the problem?

  Read the article

• Custom resolution - Windows 7 - no drivers

  - by Vytautas Butkus

  I'm having some problems with my VGA card. When I enable my VGA drivers and boot windows up they crash and I get message that the problem occured with atimdag.sys drivers or smth like that. I'm gettin BSOD all the time, unless I go to control panel and I disable drivers manually. I can live with disabled drivers just fine(I'm already used to it in quite some time) but the annoying problem is my display resolution. I can not set my res to anything higher than 1024x768. I was wondering if it's possible to change resolution to my native displays resolution without drivers? I've been trying to find something that would work w/o drivers, but with no luck(I've found many of solutions how to do it with working drivers, but as you know I can not enable my drivers). So please, maybe someone could help me and tell me how to set custom resolution?

  Read the article

• Adeos's role w.r.t Linux

  - by Anisha Kaul

  The event pipeline The fundamental Adeos structure one must keep in mind is the chain of client domains asking for event control. A domain is a kernelbased software component which can ask the Adeos layer to be notified of: · Every incoming external interrupt, or autogenerated virtual interrupt; · Every system call issued by Linux applications, · Other system events triggered by the kernel code (e.g. Linux task switching, signal notification, Linux task exits etc.). From: Life with Adeos: http://www.xenomai.org/documentation/xenomai-2.4/pdf/Life-with-Adeos-rev-B.pdf Question: Adeos is supposed to be between the hardware and the Linux kernel, I can understand about Adeos telling the Linux about hardware interrupts but Why should Adeos know about the "system call" issued by Linux?

  Read the article

• Windows 7: Wi-Fi connection drops intermittently - only returns after "Troubleshoot connection" resets the adapter

  - by sleske

  On our laptop (running Windows 7) the Wi-Fi connection drops intermittently. Symptoms: Connectivity is suddenly lost, and the "signal strenght" indicator in the tray shows zero strength and a yellow "star" symbol. What happens then: The problem does not resolve itself by just waiting. If I click on the tray icon, the "Windows network diagnostics" wizard pops up and tells me that there is a networking problem (duh). If I click on the "repair" button (not sure about the wording), the wizard works for a while, then reports that it has reset the network adapter. Then Wi-Fi works again. While the above procedure has worked every time so far, it is very annoying. It takes 10-20s to repair the connection, and in the meantime downloads, video streams etc. may have been aborted. Some more details: The problem occurs without any apparent regularity, but usually a few minutes after powerup (though not every time). It happens frequently enough to be annoying. It is unlikely to be a router problem - another laptop running at the same time usually has no Wi-Fi problems. I am at a loss about what to try to troubleshoot this. Any ideas? Computer: Acer Aspire 7739Z. Wi-Fi card: Atheros AR5B125

  Read the article

• Internet Explorer 9 send page by email grayed out

  - by catester

  Internet Explorer 9 in Windows 7 Home Premium 64-bit has the items Send Page by email and Send link by email grayed out. The default email client is Windows Live Mail 2011. I have used the "Set Default" dialogs to do that. Everything else recognizes Windows Live Mail 2011 as the default, including Firefox 4. I have duplicated this problem on two computers here. I have changed the default email program to Mozilla Thunderbird on one of the computers, and IE9 won't let me Send Page by email or Send link by email there, either. Has anyone gotten this to work? Firefox is my default browser, but sometimes I have to use IE9.

  Read the article

• Citrix ICA Client on Mac shift key doesn't work as expected

  - by brianegge

  When I'm connected to a Windows XP computer from my Mac OS X 10.6 using the Citrix ICA Client, it seems that the shift key only works for the first letter typed after pressing shift. In order to type multiple uppercase letters, like ICA, I must either press caps lock, or press and release shift before each character. I've tried switching between standard and enhanced keyboard, as well as the 'Send Special Keys Unchanged' option, but none of these seem to affect the issue. The problem doesn't occur when I switch from the Citrix window to a regular Mac window.

  Read the article

• Multiple monitors with MAC latop/PC: how to switch output?

  - by Dane Jung

  I have two monitors, a PC that uses both of them, and a MAC laptop. The dilemma in my mind is how to keep the two monitor state in the PC active, while still being able to switch one monitor to the laptop's output. Is this even possible? I figure as soon as output is switched, my PC will detect a monitor has been unplugged, and will switch to a one-monitor state. The ideal would be to have a switch that switches from the PC two monitor output state to one where one monitor is being used by the MAC. Thanks for any help, Dane

  Read the article

• Suspend only works once after full power cycle with ASUS P7P55D-E Pro

  - by John Chadwick

  This one is strange. I can't seem to get suspend working more than once per power cycle. When I say "power cycle," I mean the only way to get one proper suspend is to cut power from the power supply and boot back up cold. After the proper suspend, I get a failed suspend, and after all reboots or cold boots until power is cut, suspends fail. I'm using an ASUS P7P55D-E Pro with a Sandy Bridge Core i7, running on Ubuntu Precise repositories and UEFI. I'm running Nouveau from repository (And Gallium3d compiled from git, but that does not come into this since I can avoid OpenGL and it still happens the same way) with a GTX 285 (nv50.) I had to build a custom kernel (3.3) in order for ACPI 5.0 to be supported and make suspend work at all. I compiled it using the latest Ubuntu kernel's config file with the additional entries set to the default options. All packages are up to date. I know these are relatively exotic settings, but I'm hoping maybe I can get some help anyways. The behavior when suspend fails is strange. Upon a proper suspend, all fans turn off and the only led left on, the power led, is blinking. Upon a failed suspend, 1. USB power remains. 2. The power led stays on solid. 3. All fans seem to still be on. 4. I can hear what I believe is the primary harddrive shutting off. 5. Despite USB power remaining, the USB powered keyboard does not respond to anything, and the indicator leds on it shut off. Pressing the power button does nothing, and of course I have not to date found a way to wake it up. When trouble shooting the first round of issues I got with suspend not too long ago, I ended up building a list of modules to disable upon sleeping. Here's my config file for them: In /etc/pm/config.d/01modules: SUSPEND_MODULES="uhci_hd ehci_hd button" All of my other pm configuration files are stock. In case it's any help, here are my relevant BIOS settings. Thanks.

  Read the article

• Mac OS X Lion (10.7) Drive Encryption

  - by Skoota

  My iMac has two drives (a 256 GB solid-state drive, and regular 2 TB hard drive). The Mac OS X Lion system is installed on the solid-state drive and, like many other users, I have moved my user profile folder onto the secondary 2 TB drive. However, as you may be aware, FileVault 2 on Mac OS X Lion (10.7) only encrypts the system drive. This leaves my data drive (containing my user profile folder, with all of my data) unencrypted. I am aware that work arounds for this issue exist (such as https://github.com/jridgewell/Unlock) but I am not happy with the results since they involve decrypting the data drive on startup using a LaunchDaemon (before any users have logged into the computer) essentially meaning that any user who logs onto the computer will see the unencrypted drive. I would like a method which will only unencrypted the data when an authorised user logs into the computer. As such, is there a way to do one of the following? Encrypt the entire data drive and only decrypt the drive when an authorised user logs into the computer. This would be equivalent behaviour to the Lion FileVault 2 feature, but on a secondary drive rather than the system drive. Encrypt only the user profile folder on the data drive, and only decrypt the folder when the user logs into the computer. This would be equivalent to the behaviour of FileVault 1 on previous versions of Mac OS X? I am happy to pay for a commercial third-party product that provides the required feature(s), but I have not yet been able to find one. Thanks in advance for any assistance.

  Read the article

• How can I see a visual overlay of shortcut keys I've pressed?

  - by lyricsboy

  I've seen several screencasts (recorded on Mac OS X) which show a nice little "toast" indicating which shortcut key is being pressed by the screencaster, typically in the middle of the screen. Is this a feature of the screencasting software? Is there an app that does this that stands alone? I regularly do presentations for programming classes, and I want a way to show my audience what shortcuts I'm activating.

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >