Search Results

Search found 345 results on 14 pages for 'duplex'.

Page 10/14 | < Previous Page | 6 7 8 9 10 11 12 13 14 | Next Page >

Solaris 10 invalid ARP requests from 0.0.0.0? Link up/down every hour or 2

- by JWD

The guys at the data center where I'm hosting a server running Solaris 10 are telling me that my server is making a lot of invalid arp requests. This is an example of a portion of what was sent to me from the logs (with Mac addresses and IP addresses changed). [mymacaddress]/0.0.0.0/0000.0000.0000/[myipaddress]/[Datestamp]) It's being logged every hour. I don't see anything in the arp tables (arp -a) or routing tables (netstat -r) and I don't see anything relating to 0.0.0.0 when snoping the arp requests. The only place I see any reference to 0.0.0.0 is if I do netstat -a for the SCTP SCTP: Local Address Remote Address Swind Send-Q Rwind Recv-Q StrsI/O State ------------------------------- ------------------------------- ------ ------ ------ ------ ------- ----------- 0.0.0.0 0.0.0.0 0 0 102400 0 32/32 CLOSED But not really sure what that means. Doesn't seem like I can disable SCTP. There are some tunable SCTP parameters but it's not something I'm familiar with. Do I have to add changes to /etc/system? Looks like sctp_heartbeat_interval might be what I need to change? If it makes any difference, I have a few solaris zones running on this server, each with their own IP address on a virtual interface. eth0:0, eth0:1, etc. Does anyone have any idea what might be causing this and how to stop it? I think the switch I'm connected to doesn't like it and momentarily drops the connection. Is there anyway to at least block those requests using ipfilter or something else? Update: This was happening more frequently but now it seems to be happening roughly every hour or every two hours. It's not consistent. I tried setting setting the link speed and duplex to match the switch port and that seemed to make it stop happening for a few hours but then it started again.

Read the article
Why does my Intel Tolapai network chip not transmit packets?

- by Hanno Fietz

I'm trying to deploy an embedded system (NISE 110 by Nexcom) based on the Intel EP80579 (Tolapai) chip. Tolapai apparently integrates controllers for Ethernet etc. on a single chip (Intel homepage). The machine can't get a network connection. Diagnosis as far as I could manage: Drivers drivers from Intel compiled and installed without problems (version 1.0.3-144). Kernel version and Linux distribution (CentOS 5.2, 2.6.18) match the driver's installation instructions. drivers are loaded and show up in lsmod (module names are gcu and iegbe) interfaces eth0 and eth1 show up in ifconfig ifconfig I can bring up the interfaces with fixed IP pinging the interface locally works ifconfig shows flag UP but not RUNNING Link ethtool shows "Link detected: no", "Speed: unknown (65536)" and "Duplex: unknown (255)" Link LED is on on the other side of the cable, ethtool shows "Link detected: yes" and reports a speed of 1000 Mbps, which has allegedly been auto-neogotiated with the problematic device. Network traffic analysis the device does not reply on ARP, ICMP echo or anything else (iptables is down) when trying to send ICMP or DHCP requests, they never reach the other end activity LED is off on the device, on at the other end. I tried the following without any effect: Different cables (2 straight, one crossed), I get the link LED lit up on each. Three different devices on the other end (one PC, one netbook, one router) Fixed ARP table entries on both sides Connecting both network ports of the machine with each other, won't ping through the cable, but will ping locally. Tried straight and crossed cables for that.

Read the article
Problems with 5.1 digital out on Ubuntu 12.04

- by user895319

I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

Read the article
Gigabit LAN not working on ASUS M2N-MX

- by chmod

Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

Read the article
Arch Linux: eth0 no carrier - network fails at boot

- by user905686

The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

Read the article
No sound Ubuntu 10.10 (have SB Live! card)

- by Chris Frazier

I am new to Linux/Ubuntu and I just installed 10.10 on my Dell Desktop PC that was running Windows XP. The PC is about 5-6 years old and the sound card it has is a SoundBlaster Live! card. The Sound Preferences recognizes the card as [SB Live! Value] EMU10k1X. It is currently set to Analog Stereo Duplex. I tried multiple other sound configurations and nothing works. No sound but some clicks come out of the speakers. I ran the system test and during the audio tests the same thing happened, just clicks and pops. I tried to play some music with Rhythmbox and when it tries to play a track it tries for several seconds and then just closes itself, or sometimes just doesn't play. I ran a check for drivers, but the only driver it found to install was for my nVidia video card. It did not show any drivers for the sound card. Does anyone have any idea what I need to do to get the sound to work?

Read the article
Ubuntu 10.04 network manager issues

- by Shark

I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

Read the article
Backtrack, Wi-Fi not working

- by hradecek

I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

Read the article
Buying an old laser printer -- what will need to be replaced?

- by marienbad

Hi all -- as you can see I'm new. I do IT and wiring for a small local shop but I never deal with printers. I do a LOT of printing, and I'd like to stop spending as much money on it. On my local CL, there is an HP 8100DN (duplex network) printer for a very good price (and the toner is a quarter-cent per page). It has printed 200,000 pages and I don't yet know anything else about it. The model was released in 1999. So my questions: What are the parts that tend to need service on laser printers? On ebay, I see fusers, rollers, DC power boards, and motors. What would you expect to replace soon at 200,000 pages? Are there any good "tests" to find out if certain parts are near failure? Do you have anything to say about the HP 8100 specifically? The bottom line for me is that if there's any chance of repairs costing more than $100, it's not worth it for me.

Read the article
Network Sniffing and Hubs

- by Chris_K

This will likely seem naive to the experts... but it has been on my mind lately. For years I've been using ntop and a cheap 4 port hub to sniff client networks to determine who's doing what -- and how much. Great way to see what's going on when they call and say "Geeze, the network seems really slow today." No need to bring in a managed switch (or access the existing one) and no need to configure spanning or mirroring. I just drop in the hub inline where I want to measure. Lately I noticed it is just about impossible to buy a real honest-to-goodness hub anymore. While looking for a new one, I had someone tell me that I should be sure to get a full-duplex hub or I'd only be seeing half the traffic when I monitor. Really? I've been using a crusty old Netgear DS104 all this time. No clue if it is half or FD. Have I really been understating my measurements? I'm just not bright enough about the physical layer to really know... Side note: Just ordered a Dualcomm Ethernet Switch TAP as a hub replacement. Seems like a nifty gadget. Any notes or tips about it would be welcome in the comments :-)

Read the article
How to define nodes from a Hiera file in Puppet?

- by Pigueiras

I am using puppet and the puppet network device management module and I am trying to build my custom type. In the built-in type for the routers configuration, you can specify a list of nodes and then the configuration inside that node: node "c2950.domain.com" { Interface { duplex => auto, speed => auto } interface { "FastEthernet 0/1": description => "--> to end-user workstation", mode => access, native_vlan => 1000 # [...] More configuration } What I am trying to do, is to move the manifest declaration of the nodes and the configuration of my custom type to a Hiera file like this one: nodes: - node1 - node2 config_device: node1: custom_parameter: "whatever1" node2: custom_parameter: "whatever2" And then in the manifest iterate over the hiera file creating the nodes with the configuration of each node with something like (I am taking as reference this question in serverfault): class my_class { $nodes = hiera_array('nodes') define hash_extract() { $conf_hash = hiera_hash("config_device") $custom_paramter = $conf_hash[$name] ## TRICK lies in $name variable node $name { my_custom_device { $name: custom_parameter => $device_conf['custom_parameter'] } } } hash_extract{$pdu_names: } } } But for this solution I have two problems, I can not define a node inside a define and I can not parameterize a node name. So, is there any way to declare nodes from a Hiera file with their configuration inside?

Read the article
Two cisco gigabit switches refuse to link to each other. Any idea why?

- by Prody

I have 3 Linksys SR2024 switches which are basically non-managed 24 port Gbit + 2 miniGBIC. I now had to add another switch to the network, and my provider didn't have the SR2024 switch anymore, so I got the Cisco SLM2024 which was a bit more expensive. It's pretty much the same thing but with management (that I don't need). So I've connected the SLM2024 to a SR2024 via Cat6 cable, and for some strange reason, I get no link. If I connect any machine with a Gbit NIC to both switches, it links with 1Gbit autonegotiated. If I connect the SLM2024 to a non-Gbit switch (I have a cheap 4port ASUS switch), it will link just fine on 100Mbit full duplex. Since the SLM2024 has management, I've tried to see if something is misconfigured on it's side, but it's not, it advertises 1Gbit and lower. (hence the machines connecting succesfully at 1Gbit). Since the SR2024 that I'm trying to connect it to also connects successfully with another SR2024 and other Gbit machines, it means that it advertises Gbit too. But for some reason when I link the SR2024 to the SLM2024 I get no link. Please note that I've properly tested the wire. Does anyone have any idea what's wrong?

Read the article
Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

- by user94217

I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

Read the article
Can't connect to wi-fi hotspot in Ubuntu 11.10

- by ht3t

I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

Read the article
PC hangs and reboots from time to time

- by Bevor

Hello, I have a very strange problem: Since I have my new PC, I have always had problems with it. From time to time the computer freezes for some seconds and suddendly reboots by itself. I've had this problem since Ubuntu 9.10. The same with 10.04 and 10.10. That's why I don't think it's a software failure because the problem persist too long. It doesn't have anything to do with what I'm doing at this time. Sometimes I listen to music, sometimes I only use Firefox, sometimes I'm running 2 or 3 VMs, sometimes I watch DVD. So it's not isolatable. I could freeze once a day or once a week. I put the PC to the vendor twice(!). The first time they changed my power supply but the problem persisted. The second time they told me that they made some heavy performance tests 50 hours long but they didn't find anything. (How can that be that I have daily freezes with normal usage). The vendor didn't check the hard discs because they used their own disc with Windows. (So they never checked the Linux installation). Yesterday I made some intensive hard disc scans with "SMART" but no errors were found. I ran memtest for 3 times but no errors found. I already had this problem in my old flat, so I doubt that I has something to do with current fluctuation. I already tried another electrical socket and changed to connector strip but the problem persists. At the moment I removed 2 of the RAMs (2x 2GB). In all I have 6GB, 2x2GB and 2x1GB. Could this difference maybe be a problem? Here is a list of my components. I hope that anybody find something I didn't think about yet. And here a list of my components: 1x AMD Phenom II X4 965 Black Edition, 3,4Ghz, Quad Core, S-AM3, Boxed 2x DDR3-RAM 2048MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x DDR3-RAM 1024MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x SATA II Seagate Barracuda 7200.12, 1TB 32MB Cache = RAID 1 1x DVD ROM SATA LG DH16NSR, 16x/52x 1x DVD-+R/-+RW SATA LG GH-22NS50 1x Cardreader 18in1 1x PCI-E 2.0 GeForce GTS 250, Retail, 1024MB 1x Power Supply ATX 400 Watt, CHIEFTEC APS-400S, 80 Plus 1x Network card PCI Intel PRO/1000GT 10/100/1000 MBit 1x Mainboard Socket-AM3 ASUS M4A79XTD EVO, ATX lshw: description: Desktop Computer product: System Product Name vendor: System manufacturer version: System Version serial: System Serial Number width: 64 bits capabilities: smbios-2.5 dmi-2.5 vsyscall64 vsyscall32 configuration: boot=normal chassis=desktop uuid=80E4001E-8C00-002C-AA59-E0CB4EBAC29A *-core description: Motherboard product: M4A79XTD EVO vendor: ASUSTeK Computer INC. physical id: 0 version: Rev X.0X serial: MT709CK11101196 slot: To Be Filled By O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 0704 (11/25/2009) size: 64KiB capacity: 960KiB capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification *-cpu description: CPU product: AMD Phenom(tm) II X4 965 Processor vendor: Advanced Micro Devices [AMD] physical id: 4 bus info: cpu@0 version: AMD Phenom(tm) II X4 965 Processor serial: To Be Filled By O.E.M. slot: AM3 size: 800MHz capacity: 3400MHz width: 64 bits clock: 200MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp x86-64 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 512KiB capacity: 512KiB capabilities: pipeline-burst internal varies data *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 2MiB capacity: 2MiB capabilities: pipeline-burst internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: pipeline-burst internal varies unified *-memory description: System Memory physical id: 36 slot: System board or motherboard size: 2GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber00 vendor: Manufacturer00 physical id: 0 serial: SerNum00 slot: DIMM0 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber01 vendor: Manufacturer01 physical id: 1 serial: SerNum01 slot: DIMM1 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: DIMM [empty] product: ModulePartNumber02 vendor: Manufacturer02 physical id: 2 serial: SerNum02 slot: DIMM2 *-bank:3 description: DIMM [empty] product: ModulePartNumber03 vendor: Manufacturer03 physical id: 3 serial: SerNum03 slot: DIMM3 *-pci:0 description: Host bridge product: RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part vendor: ATI Technologies Inc physical id: 100 bus info: pci@0000:00:00.0 version: 00 width: 32 bits clock: 66MHz *-pci:0 description: PCI bridge product: RD790 PCI to PCI bridge (external gfx0 port A) vendor: ATI Technologies Inc physical id: 2 bus info: pci@0000:00:02.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:a000(size=4096) memory:f8000000-fbbfffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ac00(size=128) memory:fbbe0000-fbbfffff *-pci:1 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port C) vendor: ATI Technologies Inc physical id: 6 bus info: pci@0000:00:06.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:b000(size=4096) memory:fbc00000-fbcfffff ioport:f6f00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: e0:cb:4e:ba:c2:9a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:45 ioport:b800(size=256) memory:f6fff000-f6ffffff memory:f6ff8000-f6ffbfff memory:fbcf0000-fbcfffff *-pci:2 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port D) vendor: ATI Technologies Inc physical id: 7 bus info: pci@0000:00:07.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:c000(size=4096) memory:fbd00000-fbdfffff *-firewire description: FireWire (IEEE 1394) product: VT6315 Series Firewire Controller vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:03:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress ohci bus_master cap_list configuration: driver=firewire_ohci latency=0 resources: irq:19 memory:fbdff800-fbdfffff ioport:c800(size=256) *-pci:3 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port E) vendor: ATI Technologies Inc physical id: 9 bus info: pci@0000:00:09.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:d000(size=4096) memory:fbe00000-fbefffff *-ide description: IDE interface product: 88SE6121 SATA II Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 version: b2 width: 32 bits clock: 33MHz capabilities: ide pm msi pciexpress bus_master cap_list configuration: driver=pata_marvell latency=0 resources: irq:17 ioport:dc00(size=8) ioport:d880(size=4) ioport:d800(size=8) ioport:d480(size=4) ioport:d400(size=16) memory:fbeffc00-fbefffff *-storage description: SATA controller product: SB700/SB800 SATA Controller [IDE mode] vendor: ATI Technologies Inc physical id: 11 bus info: pci@0000:00:11.0 logical name: scsi0 logical name: scsi2 version: 00 width: 32 bits clock: 66MHz capabilities: storage msi ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=64 resources: irq:44 ioport:9000(size=8) ioport:8000(size=4) ioport:7000(size=8) ioport:6000(size=4) ioport:5000(size=16) memory:f7fffc00-f7ffffff *-disk:0 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: CC38 serial: 9VP3WD9Z size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@0:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@0:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-disk:1 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/sdb version: CC38 serial: 9VP3SCPF size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@2:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@2:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@2:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@2:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-usb:0 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 12 bus info: pci@0000:00:12.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffd000-f7ffdfff *-usb:1 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 12.1 bus info: pci@0000:00:12.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffe000-f7ffefff *-usb:2 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 12.2 bus info: pci@0000:00:12.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:17 memory:f7fff800-f7fff8ff *-usb:3 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 13 bus info: pci@0000:00:13.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffb000-f7ffbfff *-usb:4 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 13.1 bus info: pci@0000:00:13.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffc000-f7ffcfff *-usb:5 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 13.2 bus info: pci@0000:00:13.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:19 memory:f7fff400-f7fff4ff *-serial UNCLAIMED description: SMBus product: SBx00 SMBus Controller vendor: ATI Technologies Inc physical id: 14 bus info: pci@0000:00:14.0 version: 3c width: 32 bits clock: 66MHz capabilities: ht cap_list configuration: latency=0 *-ide description: IDE interface product: SB700/SB800 IDE Controller vendor: ATI Technologies Inc physical id: 14.1 bus info: pci@0000:00:14.1 logical name: scsi5 version: 00 width: 32 bits clock: 66MHz capabilities: ide msi bus_master cap_list emulated configuration: driver=pata_atiixp latency=64 resources: irq:16 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:ff00(size=16) *-cdrom:0 description: DVD reader product: DVDROM DH16NS30 vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom1 logical name: /dev/dvd1 logical name: /dev/scd0 logical name: /dev/sr0 version: 1.00 capabilities: removable audio dvd configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@5:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: ATI Technologies Inc physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=64 resources: irq:16 memory:f7ff4000-f7ff7fff *-isa description: ISA bridge product: SB700/SB800 LPC host controller vendor: ATI Technologies Inc physical id: 14.3 bus info: pci@0000:00:14.3 version: 00 width: 32 bits clock: 66MHz capabilities: isa bus_master configuration: latency=0 *-pci:4 description: PCI bridge product: SBx00 PCI to PCI Bridge vendor: ATI Technologies Inc physical id: 14.4 bus info: pci@0000:00:14.4 version: 00 width: 32 bits clock: 66MHz capabilities: pci subtractive_decode bus_master resources: ioport:e000(size=4096) memory:fbf00000-fbffffff *-network description: Ethernet interface product: 82541PI Gigabit Ethernet Controller vendor: Intel Corporation physical id: 5 bus info: pci@0000:05:05.0 logical name: eth1 version: 05 serial: 00:1b:21:56:f3:60 size: 100MB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k6-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=64 link=yes mingnt=255 multicast=yes port=twisted pair speed=100MB/s resources: irq:20 memory:fbfe0000-fbffffff memory:fbfc0000-fbfdffff ioport:ec00(size=64) memory:fbfa0000-fbfbffff *-usb:6 description: USB Controller product: SB700/SB800 USB OHCI2 Controller vendor: ATI Technologies Inc physical id: 14.5 bus info: pci@0000:00:14.5 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffa000-f7ffafff *-pci:1 description: Host bridge product: Family 10h Processor HyperTransport Configuration vendor: Advanced Micro Devices [AMD] physical id: 101 bus info: pci@0000:00:18.0 version: 00 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Family 10h Processor Address Map vendor: Advanced Micro Devices [AMD] physical id: 102 bus info: pci@0000:00:18.1 version: 00 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Family 10h Processor DRAM Controller vendor: Advanced Micro Devices [AMD] physical id: 103 bus info: pci@0000:00:18.2 version: 00 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Family 10h Processor Miscellaneous Control vendor: Advanced Micro Devices [AMD] physical id: 104 bus info: pci@0000:00:18.3 version: 00 width: 32 bits clock: 33MHz configuration: driver=k10temp resources: irq:0 *-pci:5 description: Host bridge product: Family 10h Processor Link Control vendor: Advanced Micro Devices [AMD] physical id: 105 bus info: pci@0000:00:18.4 version: 00 width: 32 bits clock: 33MHz *-scsi physical id: 1 bus info: usb@2:3 logical name: scsi8 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@8:0.0.0 logical name: /dev/sdc *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@8:0.0.1 logical name: /dev/sdd *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@8:0.0.2 logical name: /dev/sde *-disk:3 description: SCSI Disk physical id: 0.0.3 bus info: scsi@8:0.0.3 logical name: /dev/sdf *-network DISABLED description: Ethernet interface physical id: 1 logical name: vboxnet0 serial: 0a:00:27:00:00:00 capabilities: ethernet physical configuration: broadcast=yes multicast=yes

Read the article
Tuxedo 11gR1 Client Server Affinity

- by todd.little

One of the major new features in Oracle Tuxedo 11gR1 is the ability to define an affinity between clients and servers. In previous releases of Tuxedo, the only way to ensure that multiple requests from a client went to the same server was to establish a conversation with tpconnect() and then use tpsend() and tprecv(). Although this works it has some drawbacks. First for single-threaded servers, the server is tied up for the entire duration of the conversation and cannot service other clients, an obvious scalability issue. I believe the more significant drawback is that the application programmer has to switch from the simple request/response model provided by tpcall() to the half duplex tpsend() and tprecv() calls used with conversations. Switching between the two typically requires a fair amount of redesign and recoding. The Client Server Affinity feature in Tuxedo 11gR1 allows by way of configuration an application to define affinities that can exist between clients and servers. This is done in the *SERVICES section of the UBBCONFIG file. Using new parameters for services defined in the *SERVICES section, customers can determine when an affinity session is created or deleted, the scope of the affinity, and whether requests can be routed outside the affinity scope. The AFFINITYSCOPE parameter can be MACHINE, GROUP, or SERVER, meaning that while the affinity session is in place, all requests from the client will be routed to the same MACHINE, GROUP, or SERVER. The creation and deletion of affinity is defined by the SESSIONROLE parameter and a service can be defined as either BEGIN, END, or NONE, where BEGIN starts an affinity session, END deletes the affinity session, and NONE does not impact the affinity session. Finally customers can define how strictly they want the affinity scope adhered to using the AFFINITYSTRICT parameter. If set to MANDATORY, all requests made during an affinity session will be routed to a server in the affinity scope. Thus if the affinity scope is SERVER, all subsequent tpcall() requests will be sent to the same server the affinity scope was established with. If the server doesn't offer that service, even though other servers do offer the service, the call will fail with TPNOENT. Setting AFFINITYSTRICT to PRECEDENT tells Tuxedo to try and route the request to a server in the affinity scope, but if that's not possible, then Tuxedo can try to route the request to servers out of scope. All of this begs the question, why? Why have this feature? There many uses for this capability, but the most common is when there is state that is maintained in a server, group of servers, or in a machine and subsequent requests from a client must be routed to where that state is maintained. This might be something as simple as a database cursor maintained by a server on behalf of a client. Alternatively it might be that the server has a connection to an external system and subsequent requests need to go back to the server that has that connection. A more sophisticated case is where a group of servers maintains some sort of cache in shared memory and subsequent requests need to be routed to where the cache is maintained. Although this last case might be able to be handled by data dependent routing, using client server affinity allows the cache to be partitioned dynamically instead of statically.

Read the article
Networking- Wireless and Wired not working

- by JJ White

So everything in Ubuntu has been working great until networking stopped working. I've spent the better part of two days scouring for a fix with no luck. Here is my info...your help would so be appreciated. grep -i eth /var/log/syslog | tail Sep 25 16:31:59 jj-laptop NetworkManager[970]: <info> (eth0): cleaning up... Sep 25 16:31:59 jj-laptop NetworkManager[970]: <info> (eth0): taking down device. Sep 25 16:31:59 jj-laptop kernel: [23403.998837] sky2 0000:02:00.0: eth0: disabling interface Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): now managed Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): bringing up device. Sep 25 16:35:54 jj-laptop kernel: [23413.629424] sky2 0000:02:00.0: eth0: enabling interface Sep 25 16:35:54 jj-laptop kernel: [23413.635703] ADDRCONF(NETDEV_UP): eth0: link is not ready Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): preparing device. Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): deactivating device (reason 'managed') [2] and then ifconfig -a eth0 Link encap:Ethernet HWaddr 00:17:42:14:e9:e1 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:4605 errors:0 dropped:0 overruns:0 frame:0 TX packets:287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:315161 (315.1 KB) TX bytes:63680 (63.6 KB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13018 errors:0 dropped:0 overruns:0 frame:0 TX packets:13018 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:880484 (880.4 KB) TX bytes:880484 (880.4 KB) wlan0 Link encap:Ethernet HWaddr 00:13:02:d0:ee:13 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) also iwconfig lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. and of course sudo lshw -C network *-network description: Ethernet interface product: 88E8055 PCI-E Gigabit Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 12 serial: 00:17:42:14:e9:e1 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A latency=0 link=no multicast=yes port=twisted pair speed=1Gbit/s resources: irq:44 memory:f0000000-f0003fff ioport:2000(size=256) memory:c0a00000-c0a1ffff *-network DISABLED description: Wireless interface product: PRO/Wireless 3945ABG [Golan] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 02 serial: 00:13:02:d0:ee:13 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl3945 driverversion=3.2.0-31-generic firmware=15.32.2.9 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:45 memory:c0100000-c0100fff last but not least lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 dm_crypt 22528 0 rfcomm 38139 0 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 bluetooth 158438 10 rfcomm,bnep binfmt_misc 17292 1 snd_hda_codec_idt 60251 1 pcmcia 39791 0 joydev 17393 0 snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 yenta_socket 27428 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event pcmcia_rsrc 18367 1 yenta_socket wacom_w8001 12906 0 irda 185517 0 arc4 12473 2 iwl3945 73111 0 iwl_legacy 71134 1 iwl3945 mac80211 436455 2 iwl3945,iwl_legacy cfg80211 178679 3 iwl3945,iwl_legacy,mac80211 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq dm_multipath 22710 0 pcmcia_core 21511 3 pcmcia,yenta_socket,pcmcia_rsrc psmouse 96619 0 apanel 12718 0 serport 12808 1 serio_raw 13027 0 crc_ccitt 12595 1 irda mac_hid 13077 0 snd 62064 15 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_t imer,snd_seq_device input_polldev 13648 1 apanel soundcore 14635 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm lp 17455 0 fujitsu_laptop 18504 0 parport 40930 3 parport_pc,ppdev,lp dm_raid45 76451 0 xor 25987 1 dm_raid45 dm_mirror 21822 0 dm_region_hash 16065 1 dm_mirror dm_log 18193 3 dm_raid45,dm_mirror,dm_region_hash sdhci_pci 18324 0 sdhci 28241 1 sdhci_pci sky2 49545 0 i915 414939 3 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915

Read the article
A Forming Repository of Script Samples for Automating Windows Server 2012 and Windows 8

- by Jialiang

Compared with Windows Server 2008/R2 that provides about 230 cmdlets, Windows Server 2012 beats that by a factor of over 10 shipping ~ 2,430 cmdlets. You can automate almost every aspect of the server. The new PowerShell 3.0, like Windows Server 2012, has a ton of new features. In this automation script-centric move, Microsoft All-In-One Script Framework (AIOSF) is ready to support IT Pros with many new services and offerings coming this year. We sincerely hope that the IT community will benefit from the effort. Here is the first one among our new services and offerings: The team is preparing a large set of Windows 8 / Windows Server 2012 script samples based on frequently asked IT tasks that we collect in TechNet forums and support calls to Microsoft. Because the script topics come from frequently asked IT tasks, we hope that these script samples can be helpful to many IT Pros worldwide. With the General Availability of Windows Server 2012, we release the first three Windows Server 2012 / Windows 8 script samples today. Get Network Adapter Properties in Windows Server 2012 and Windows 8 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/Get-Network-Adapter-37c5a913 Description: This script could be used to get network adapter properties and advanced properties in Windows Server 2012 and Windows 8. It combines the outputs of Get-NetAdapter and Get-NetAdapterAdvancedProperty. It can generate a report of network adapter configuration settings. Use Scenarios: In a real world, IT Administrators are required to check the configuration of network adapters after the deployment of new servers. One typical example is the duplex setting of network adapters. Also, IT administrators need to maintain a server list which contains network adapter configuration settings in a regular basis. Before Windows Server 2012, IT administrators often feel difficulties to handle these tasks. Acknowledgement: Thanks Greg Gu from AIOSF for collecting this script topic, and writing the script sample. Thanks James Adams (Microsoft Premier Field Engineer) for reviewing the script sample and ensuring its quality. How to batch create virtual machines in Windows Server 2012 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/How-to-batch-create-9efd1811 Description: This PowerShell Script illustrates how to batch create multiple virtual machines based on comma delimited file by using PowerShell 3.0 in Windows Server 2012. Use Scenarios: IT admin requires to batch creating virtual machines in Windows Server 2012, although they can use few commands due to the lack of programming knowledge. Although it’s a set of Hyper-V command-lets within Windows PowerShell, IT Admins are reluctant to use them except simple a command which is widely used. Acknowledgement: Thanks Anders Wang from AIOSF for collecting this script topic and writing the script sample. Thanks Christopher Norris for reviewing the script sample and ensuring its quality before publishing. Remove Windows Store Apps in Windows 8 (PowerShell) http://gallery.technet.microsoft.com/scriptcenter/Remove-Windows-Store-Apps-a00ef4a4 Description: This script can be used to remove multiple Windows Store Apps from a user account in Windows 8. It provides a list of installed Windows Store applications. You can specify the application IDs, and remove them all at once. Use Scenarios: 1. In Windows 8, you can remove a single Windows Store App by right-clicking the tile in the Start menu and choosing the uninstall command. However, no command is provided for removing multiple Windows Store Apps all at once. If you want to do so, you can use this script sample. 2. Sometimes Windows Store Apps may crash in Windows 8. Even though you can successfully uninstall and reinstall the App, the application may still crash after the reinstallation. In this situation, you can use this example script to remove these Windows Store Apps cleanly. Acknowledgement: Thanks Edward Qi from AIOSF for collecting the script idea and composing the script sample. Thanks James Adams (Microsoft Premier Field Engineer) for reviewing the script sample and ensuring its quality. This is just the beginning, and more and more script samples are coming. You can follow our blog (http://blogs.technet.com/b/onescript) to get the latest customer-driven script samples for Windows Server 2012 and Windows 8.

Read the article
SPARC T5-4 LDoms for RAC and WebLogic Clusters

- by Jeff Taylor-Oracle

I wanted to use two Oracle SPARC T5-4 servers to simultaneously host both Oracle RAC and a WebLogic Server Cluster. I chose to use Oracle VM Server for SPARC to create a cluster like this: There are plenty of trade offs and decisions that need to be made, for example: Rather than configuring the system by hand, you might want to use an Oracle SuperCluster T5-8 My configuration is similar to jsavit's: Availability Best Practices - Example configuring a T5-8 but I chose to ignore some of the advice. Maybe I should have included an alternate service domain, but I decided that I already had enough redundancy Both Oracle SPARC T5-4 servers were to be configured like this: Cntl 0.25 4 64GB App LDom 2.75 CPU's 44 cores 704 GB DB LDom One CPU 16 cores 256 GB The systems started with everything in the primary domain: # ldm list NAME STATE FLAGS CONS VCPU MEMORY UTIL NORM UPTIME primary active -n-c-- UART 512 1023G 0.0% 0.0% 11m # ldm list-spconfig factory-default [current] primary # ldm list -o core,memory,physio NAME primary CORE CID CPUSET 0 (0, 1, 2, 3, 4, 5, 6, 7) 1 (8, 9, 10, 11, 12, 13, 14, 15) 2 (16, 17, 18, 19, 20, 21, 22, 23) -- SNIP 62 (496, 497, 498, 499, 500, 501, 502, 503) 63 (504, 505, 506, 507, 508, 509, 510, 511) MEMORY RA PA SIZE 0x30000000 0x30000000 255G 0x80000000000 0x80000000000 256G 0x100000000000 0x100000000000 256G 0x180000000000 0x180000000000 256G # Give this memory block to the DB LDom IO DEVICE PSEUDONYM OPTIONS pci@300 pci_0 pci@340 pci_1 pci@380 pci_2 pci@3c0 pci_3 pci@400 pci_4 pci@440 pci_5 pci@480 pci_6 pci@4c0 pci_7 pci@300/pci@1/pci@0/pci@6 /SYS/RCSA/PCIE1 pci@300/pci@1/pci@0/pci@c /SYS/RCSA/PCIE2 pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0 pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0 pci@340/pci@1/pci@0/pci@6 /SYS/RCSA/PCIE3 pci@340/pci@1/pci@0/pci@c /SYS/RCSA/PCIE4 pci@380/pci@1/pci@0/pci@a /SYS/RCSA/PCIE9 pci@380/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE10 pci@3c0/pci@1/pci@0/pci@e /SYS/RCSA/PCIE11 pci@3c0/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE12 pci@400/pci@1/pci@0/pci@e /SYS/RCSA/PCIE5 pci@400/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE6 pci@440/pci@1/pci@0/pci@e /SYS/RCSA/PCIE7 pci@440/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE8 pci@480/pci@1/pci@0/pci@a /SYS/RCSA/PCIE13 pci@480/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE14 pci@4c0/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE15 pci@4c0/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE16 pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1 pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2 Added an additional service processor configuration: # ldm add-spconfig split # ldm list-spconfig factory-default primary split [current] And removed many of the resources from the primary domain: # ldm start-reconf primary # ldm set-core 4 primary # ldm set-memory 32G primary # ldm rm-io pci@340 primary # ldm rm-io pci@380 primary # ldm rm-io pci@3c0 primary # ldm rm-io pci@400 primary # ldm rm-io pci@440 primary # ldm rm-io pci@480 primary # ldm rm-io pci@4c0 primary # init 6 Needed to add resources to the guest domains: # ldm add-domain db # ldm set-core cid=`seq -s"," 48 63` db # ldm add-memory mblock=0x180000000000:256G db # ldm add-io pci@480 db # ldm add-io pci@4c0 db # ldm add-domain app # ldm set-core 44 app # ldm set-memory 704G app # ldm add-io pci@340 app # ldm add-io pci@380 app # ldm add-io pci@3c0 app # ldm add-io pci@400 app # ldm add-io pci@440 app Needed to set up services: # ldm add-vds primary-vds0 primary # ldm add-vcc port-range=5000-5100 primary-vcc0 primary Needed to add a virtual network port for the WebLogic application domain: # ipadm NAME CLASS/TYPE STATE UNDER ADDR lo0 loopback ok -- -- lo0/v4 static ok -- ... lo0/v6 static ok -- ... net0 ip ok -- ... net0/v4 static ok -- xxx.xxx.xxx.xxx/24 net0/v6 addrconf ok -- .... net0/v6 addrconf ok -- ... net8 ip ok -- -- net8/v4 static ok -- ... # dladm show-phys LINK MEDIA STATE SPEED DUPLEX DEVICE net1 Ethernet unknown 0 unknown ixgbe1 net0 Ethernet up 1000 full ixgbe0 net8 Ethernet up 10 full usbecm2 # ldm add-vsw net-dev=net0 primary-vsw0 primary # ldm add-vnet vnet1 primary-vsw0 app Needed to add a virtual disk to the WebLogic application domain: # format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0t5000CCA02505F874d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB> /scsi_vhci/disk@g5000cca02505f874 /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD0/disk 1. c0t5000CCA02506C468d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB> /scsi_vhci/disk@g5000cca02506c468 /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD1/disk 2. c0t5000CCA025067E5Cd0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB> /scsi_vhci/disk@g5000cca025067e5c /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD2/disk 3. c0t5000CCA02506C258d0 <HITACHI-H106060SDSUN600G-A2B0-558.91GB> /scsi_vhci/disk@g5000cca02506c258 /dev/chassis/SPARC_T5-4.AK00084038/SYS/SASBP0/HDD3/disk Specify disk (enter its number): ^C # ldm add-vdsdev /dev/dsk/c0t5000CCA02506C468d0s2 HDD1@primary-vds0 # ldm add-vdisk HDD1 HDD1@primary-vds0 app Add some additional spice to the pot: # ldm set-variable auto-boot\\?=false db # ldm set-variable auto-boot\\?=false app # ldm set-var boot-device=HDD1 app Bind the logical domains: # ldm bind db # ldm bind app At the end of the process, the system is set up like this: # ldm list -o core,memory,physio NAME primary CORE CID CPUSET 0 (0, 1, 2, 3, 4, 5, 6, 7) 1 (8, 9, 10, 11, 12, 13, 14, 15) 2 (16, 17, 18, 19, 20, 21, 22, 23) 3 (24, 25, 26, 27, 28, 29, 30, 31) MEMORY RA PA SIZE 0x30000000 0x30000000 32G IO DEVICE PSEUDONYM OPTIONS pci@300 pci_0 pci@300/pci@1/pci@0/pci@6 /SYS/RCSA/PCIE1 pci@300/pci@1/pci@0/pci@c /SYS/RCSA/PCIE2 pci@300/pci@1/pci@0/pci@4/pci@0/pci@c /SYS/MB/SASHBA0 pci@300/pci@1/pci@0/pci@4/pci@0/pci@8 /SYS/RIO/NET0 ------------------------------------------------------------------------------ NAME app CORE CID CPUSET 4 (32, 33, 34, 35, 36, 37, 38, 39) 5 (40, 41, 42, 43, 44, 45, 46, 47) 6 (48, 49, 50, 51, 52, 53, 54, 55) 7 (56, 57, 58, 59, 60, 61, 62, 63) 8 (64, 65, 66, 67, 68, 69, 70, 71) 9 (72, 73, 74, 75, 76, 77, 78, 79) 10 (80, 81, 82, 83, 84, 85, 86, 87) 11 (88, 89, 90, 91, 92, 93, 94, 95) 12 (96, 97, 98, 99, 100, 101, 102, 103) 13 (104, 105, 106, 107, 108, 109, 110, 111) 14 (112, 113, 114, 115, 116, 117, 118, 119) 15 (120, 121, 122, 123, 124, 125, 126, 127) 16 (128, 129, 130, 131, 132, 133, 134, 135) 17 (136, 137, 138, 139, 140, 141, 142, 143) 18 (144, 145, 146, 147, 148, 149, 150, 151) 19 (152, 153, 154, 155, 156, 157, 158, 159) 20 (160, 161, 162, 163, 164, 165, 166, 167) 21 (168, 169, 170, 171, 172, 173, 174, 175) 22 (176, 177, 178, 179, 180, 181, 182, 183) 23 (184, 185, 186, 187, 188, 189, 190, 191) 24 (192, 193, 194, 195, 196, 197, 198, 199) 25 (200, 201, 202, 203, 204, 205, 206, 207) 26 (208, 209, 210, 211, 212, 213, 214, 215) 27 (216, 217, 218, 219, 220, 221, 222, 223) 28 (224, 225, 226, 227, 228, 229, 230, 231) 29 (232, 233, 234, 235, 236, 237, 238, 239) 30 (240, 241, 242, 243, 244, 245, 246, 247) 31 (248, 249, 250, 251, 252, 253, 254, 255) 32 (256, 257, 258, 259, 260, 261, 262, 263) 33 (264, 265, 266, 267, 268, 269, 270, 271) 34 (272, 273, 274, 275, 276, 277, 278, 279) 35 (280, 281, 282, 283, 284, 285, 286, 287) 36 (288, 289, 290, 291, 292, 293, 294, 295) 37 (296, 297, 298, 299, 300, 301, 302, 303) 38 (304, 305, 306, 307, 308, 309, 310, 311) 39 (312, 313, 314, 315, 316, 317, 318, 319) 40 (320, 321, 322, 323, 324, 325, 326, 327) 41 (328, 329, 330, 331, 332, 333, 334, 335) 42 (336, 337, 338, 339, 340, 341, 342, 343) 43 (344, 345, 346, 347, 348, 349, 350, 351) 44 (352, 353, 354, 355, 356, 357, 358, 359) 45 (360, 361, 362, 363, 364, 365, 366, 367) 46 (368, 369, 370, 371, 372, 373, 374, 375) 47 (376, 377, 378, 379, 380, 381, 382, 383) MEMORY RA PA SIZE 0x30000000 0x830000000 192G 0x4000000000 0x80000000000 256G 0x8080000000 0x100000000000 256G IO DEVICE PSEUDONYM OPTIONS pci@340 pci_1 pci@380 pci_2 pci@3c0 pci_3 pci@400 pci_4 pci@440 pci_5 pci@340/pci@1/pci@0/pci@6 /SYS/RCSA/PCIE3 pci@340/pci@1/pci@0/pci@c /SYS/RCSA/PCIE4 pci@380/pci@1/pci@0/pci@a /SYS/RCSA/PCIE9 pci@380/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE10 pci@3c0/pci@1/pci@0/pci@e /SYS/RCSA/PCIE11 pci@3c0/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE12 pci@400/pci@1/pci@0/pci@e /SYS/RCSA/PCIE5 pci@400/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE6 pci@440/pci@1/pci@0/pci@e /SYS/RCSA/PCIE7 pci@440/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE8 ------------------------------------------------------------------------------ NAME db CORE CID CPUSET 48 (384, 385, 386, 387, 388, 389, 390, 391) 49 (392, 393, 394, 395, 396, 397, 398, 399) 50 (400, 401, 402, 403, 404, 405, 406, 407) 51 (408, 409, 410, 411, 412, 413, 414, 415) 52 (416, 417, 418, 419, 420, 421, 422, 423) 53 (424, 425, 426, 427, 428, 429, 430, 431) 54 (432, 433, 434, 435, 436, 437, 438, 439) 55 (440, 441, 442, 443, 444, 445, 446, 447) 56 (448, 449, 450, 451, 452, 453, 454, 455) 57 (456, 457, 458, 459, 460, 461, 462, 463) 58 (464, 465, 466, 467, 468, 469, 470, 471) 59 (472, 473, 474, 475, 476, 477, 478, 479) 60 (480, 481, 482, 483, 484, 485, 486, 487) 61 (488, 489, 490, 491, 492, 493, 494, 495) 62 (496, 497, 498, 499, 500, 501, 502, 503) 63 (504, 505, 506, 507, 508, 509, 510, 511) MEMORY RA PA SIZE 0x80000000 0x180000000000 256G IO DEVICE PSEUDONYM OPTIONS pci@480 pci_6 pci@4c0 pci_7 pci@480/pci@1/pci@0/pci@a /SYS/RCSA/PCIE13 pci@480/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE14 pci@4c0/pci@1/pci@0/pci@8 /SYS/RCSA/PCIE15 pci@4c0/pci@1/pci@0/pci@4 /SYS/RCSA/PCIE16 pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c /SYS/MB/SASHBA1 pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4 /SYS/RIO/NET2 Start the domains: # ldm start app LDom app started # ldm start db LDom db started Make sure to start the vntsd service that was created, above. # svcs -a | grep ldo disabled 8:38:38 svc:/ldoms/vntsd:default online 8:38:58 svc:/ldoms/agents:default online 8:39:25 svc:/ldoms/ldmd:default # svcadm enable vntsd Now use the MAC address to configure the Solaris 11 Automated Installation. Database Logical Domain # telnet localhost 5000 {0} ok devalias screen /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@7/display@0 disk7 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p3 disk6 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p2 disk5 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p1 disk4 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0/disk@p0 scsi1 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@c/scsi@0 net3 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0,1 net2 /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0 virtual-console /virtual-devices/console@1 name aliases {0} ok boot net2 Boot device: /pci@4c0/pci@1/pci@0/pci@c/pci@0/pci@4/network@0 File and args: 1000 Mbps full duplex Link up Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx WLS Logical Domain # telnet localhost 5001 {0} ok devalias hdd1 /virtual-devices@100/channel-devices@200/disk@0 vnet1 /virtual-devices@100/channel-devices@200/network@0 net /virtual-devices@100/channel-devices@200/network@0 disk /virtual-devices@100/channel-devices@200/disk@0 virtual-console /virtual-devices/console@1 name aliases {0} ok boot net Boot device: /virtual-devices@100/channel-devices@200/network@0 File and args: Requesting Internet Address for xx:xx:xx:xx:xx:xx Requesting Internet Address for xx:xx:xx:xx:xx:xx Repeat the process for the second SPARC T5-4, install Solaris, RAC and WebLogic Cluster, and you are ready to go. Maybe buying a SuperCluster would have been easier.

Read the article
wifi hardware switch doesn't work on a Dell 1018

- by user42566

I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

Read the article
Errors when trying to compile the driver for the rtl8192su wireless adapter

- by Tom Brito

I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Read the article
Hardware wireless switch has no effect after suspend and 13.10 upgrade

- by blaineh

This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

Read the article
Dell 3721 Wifi problem Ubuntu 13.04

- by Sebastian

I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

Read the article
Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

- by zewone

I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe

Read the article
Wireless cycling between connected and disconnected

- by Tony Kilgore

My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

Read the article

Search Results

Search found 345 results on 14 pages for 'duplex'.

Page 10/14 | < Previous Page | 6 7 8 9 10 11 12 13 14 | Next Page >

- by JWD

- by Hanno Fietz

- by user895319

- by chmod

- by user905686

- by Chris Frazier

- by Shark

- by hradecek

- by marienbad

- by Chris_K

- by Pigueiras

- by Prody

- by user94217

- by ht3t

- by Bevor

- by todd.little

- by JJ White

- by Jialiang

- by Jeff Taylor-Oracle

- by user42566

- by Tom Brito

- by blaineh

- by Sebastian

- by zewone

- by Tony Kilgore

< Previous Page | 6 7 8 9 10 11 12 13 14 | Next Page >