Search Results

Search found 55134 results on 2206 pages for 'argument error'.

Page 1037/2206 | < Previous Page | 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044  | Next Page >

• Routing subnet over GRE tunnel

  - by eMgz

  Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

  Read the article

• Cannot Update Adobe Creative Suit

  - by Lynda

  I am attempting to check for updates using the Adobe Application Manager on Windows 8 and I get this error: The update server is not responding. The server might be offline temporarily, or the Internet or firewall settings may be incorrect. I have seen this error before on Windows 7 and remembered that I needed to disable the Microsoft Virtual WiFi Miniport Adapter. I navigated to the correct place but the Miniport Adapter was not there. After a bit of searching across several forums I saw a recommendation to change <logLevel>2</logLevel> to <logLevel>10</logLevel>. I attempted that and again it still did not work. I have also tried disabling my anti-virus protection and disabling Windows Firewall. Neither worked. I am not sure what else to try or do at this point. Are there any other recommendations to solve this issue? Notes: I am running Windows 8 Pro using the Creative Cloud Version of CS6. I check for updates by choosing Help Updates from within any Adobe Application I originally posted this question on the Adobe Forums and received no help there.

  Read the article

• Why can't I update Adobe Creative Suite?

  - by Lynda

  I am attempting to check for updates using the Adobe Application Manager on Windows 8 and I get this error: The update server is not responding. The server might be offline temporarily, or the Internet or firewall settings may be incorrect. I have seen this error before on Windows 7 and remembered that I needed to disable the Microsoft Virtual WiFi Miniport Adapter. I navigated to the correct place but the Miniport Adapter was not there. After a bit of searching across several forums I saw a recommendation to change <logLevel>2</logLevel> to <logLevel>10</logLevel>. I attempted that and again it still did not work. I have also tried disabling my anti-virus protection and disabling Windows Firewall. Neither worked. I am not sure what else to try or do at this point. Are there any other recommendations to solve this issue? Notes: I am running Windows 8 Pro using the Creative Cloud Version of CS6. I check for updates by choosing Help Updates from within any Adobe Application This issue was not present in Windows 7 before I upgraded to Windows 8 I originally posted this question on the Adobe Forums and received no help there.

  Read the article

• How can I trigger the creation of a new CLB file?

  - by Xperimental

  I'm currently having a problem with an application using COM running on Windows Vista. The application runs ok on one machine, but doesn't work on a similar configured machine. Both machines are virtual images originating from the same source image. While searching the registry for causes of this error, I came across the CLBVersion key in HKCR\CLSID which seems to have something to do with COM. The value of the key differs between the two machines (0x6 on the erroneous one, 0xc on the working one). Also there are files containing the same number in their filenames in the %SystemRoot\Registration directories of the machines. They are called R000000000006.clb and R00000000000c.clb respectively. I have already searched the windows event log for anything leading to the creation of those files (I have searched by the creation date of the files). Now a few questions regarding the registry keys and the files: Is it correct, that this is connected to COM? What is the function of the files? What causes the creation of a new "CLBVersion"? Is there a way for me to trigger the creation of a new CLB file? edit: I have now found out, that this has nothing to do with my application error. But I would still be interested in details about the registry key and the files. An installation of Visual Studio 2005 has brought the second machine to the same configuration (0xc in registry and file) as the other one.

  Read the article

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

• Tomcat6 getting crashed at regular intervals installed in Ubuntu

  - by Milesh Rout

  I have installed Tomcat6 in Ubuntu OS and when I run my web application the server gets crashed at regular intervals. I have tried a lot but not getting the solution. I have increased the memory upto 2048mb but still getting such error. Following is the error I am getting. Any help would be really appreciated. org.apache.tomcat.util.http.Parameters processParametersINFO: Invalid chunk starting at byte [312] and ending at byte [312] with a value of [null] ignoredException in thread "Timer-1" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#0" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#2" Exception in thread "com.mchange.v2.async.ThreadPoolAsynchronousRunner$PoolThread-#1" Exception in thread "Timer-2" Exception in thread "http-8080-4" Exception in thread "http-8080-8" Exception in thread "http-8080-17" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.StandardQueryCache.data" Exception in thread "org.hibernate.cache.UpdateTimestampsCache.data" Exception in thread "com.safenet.usermgmt.User.data" Exception in thread "http-8080-7" Exception in thread "http-8080-12" Exception in thread "http-8080-16" Exception in thread "http-8080-14" Exception in thread "http-8080-13" Exception in thread "http-8080-15" Exception in thread "http-8080-6" OpenJDK Client VM warning: Exception java.lang.OutOfMemoryError occurred dispatching signal SIGTERM to handler- the VM may need to be forcibly terminated

  Read the article

• How do I Install Intermediate Certificates (in AWS)?

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

  Read the article

• mod_rpaf with apache error_log

  - by Camden S.

  I'm using mod-rpaf with Apache 2.4 and it's working properly (showing the real client IP's) in my Apache access_log... but not in my error_log. My error log just shows the client IP address of the proxy server (my load balancer in this case) Here's an example of what I see in my error_log where 123.123.123.123 is the IP of my load balancer/proxy. == /usr/local/apache2/logs/error_log <== [Tue Jun 05 20:24:31.027525 2012] [access_compat:error] [pid 9145:tid 140485731845888] [client 123.123.123.123:20396] AH01797: client denied by server configuration: /wwwroot/private/secret.pdf The exact same request produces the following in my access_log where 456.456.456.456 is a real client IP (not the IP of the load balancer). 456.456.456.456 - - [05/Jun/2012:20:24:31 +0000] "GET /wwwroot/private/secret.pdf HTTP/1.1" 403 228 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.7; rv:12.0) Gecko/20100101 Firefox/12.0" Here's my httpd.conf entry: # RPAF LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 123.123.123.123 RPAFsethostname On RPAFheader X-Forwarded-For What do I need to do to get the real IP addresses showing in my Apache error_log?

  Read the article

• SSH multi-hop connections with netcat mode proxy

  - by aef

  Since OpenSSH 5.4 there is a new feature called natcat mode, which allows you to bind STDIN and STDOUT of local SSH client to a TCP port accessible through the remote SSH server. This mode is enabled by simply calling ssh -W [HOST]:[PORT] Theoretically this should be ideal for use in the ProxyCommand setting in per-host SSH configurations, which was previously often used with the nc (netcat) command. ProxyCommand allows you to configure a machine as proxy between you local machine and the target SSH server, for example if the target SSH server is hidden behind a firewall. The problem now is, that instead of working, it throws a cryptic error message in my face: Bad packet length 1397966893. Disconnecting: Packet corrupt Here is an excerpt from my ~/.ssh/config: Host * Protocol 2 ControlMaster auto ControlPath ~/.ssh/cm_socket/%r@%h:%p ControlPersist 4h Host proxy-host proxy-host.my-domain.tld HostName proxy-host.my-domain.tld ForwardAgent yes Host target-server target-server.my-domain.tld HostName target-server.my-domain.tld ProxyCommand ssh -W %h:%p proxy-host ForwardAgent yes As you can see here, I'm using the ControlMaster feature so I don't have to open more than one SSH connection per-host. The client machine I tested this with is an Ubuntu 11.10 (x86_64) and both proxy-host and target-server are Debian Wheezy Beta 3 (x86_64) machines. The error happens when I call ssh target-server. When I call it with the -v flag, here is what I get additionally: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /home/aef/.ssh/config debug1: Applying options for * debug1: Applying options for target-server.my-domain.tld debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: auto-mux: Trying existing master debug1: Control socket "/home/aef/.ssh/cm_socket/[email protected]:22" does not exist debug1: Executing proxy command: exec ssh -W target-server.my-domain.tld:22 proxy-host.my-domain.tld debug1: identity file /home/aef/.ssh/id_rsa type -1 debug1: identity file /home/aef/.ssh/id_rsa-cert type -1 debug1: identity file /home/aef/.ssh/id_dsa type -1 debug1: identity file /home/aef/.ssh/id_dsa-cert type -1 debug1: identity file /home/aef/.ssh/id_ecdsa type -1 debug1: identity file /home/aef/.ssh/id_ecdsa-cert type -1 debug1: permanently_drop_suid: 1000 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.0p1 Debian-3 debug1: match: OpenSSH_6.0p1 Debian-3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1 Debian-7ubuntu1 debug1: SSH2_MSG_KEXINIT sent Bad packet length 1397966893. Disconnecting: Packet corrupt

  Read the article

• Explorer.exe keeps crashing during log in

  - by asif

  I have got a weird problem. My windows 7 has two user accounts (both are administrator). I can log in to one account and do all sort of work. But whenever I try to log in to other account, it shows a blank screen and a messagebox pops up with "windows explorer has stopped working". The options available are: Close the program Check online for a solution and close the program The problem signature is as follows: Problem Event Name: InPageError Error Status Code: c000009c Faulting Media Type: 00000003 OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 1033 Additional Information 1: 0a9e Additional Information 2: 0a9e372d3b4ad19135b953a78882e789 Additional Information 3: 0a9e Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 If I press alt+ctrl+del and then select start task manager, it also crashes. I can not run any program using runas command (from good profile) too. The task manager and runas programs all show same problem signature. I read the similar question and followed all the steps, but no luck. Later, I viewed the event log and found that, explorer.exe could not access a file. I checked the location but the file is there. The actual message is: Windows cannot access the file C:\Users\testuser\AppData\Local\Microsoft\Windows\Caches\{AFBF9F1A-8EE8-4C77-AF34-C647E37CA0D9}.1.ver0x0000000000000020.db for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Windows Explorer because of this error. The question is, how can I resolve this issue? Should I just delete the file or replace it with another one to stop explorer.exe from crashing? offtopic: What is the content of this file and why it is necessary?

  Read the article

• Apache HTTPd FollowSymLinks path permission

  - by apast

  Hi, I'm configuring my development environment with a basic Apache HTTPd configuration. But, to avoid a often problem, I want to map my test URL to my development folder. I'm using Ubuntu. My development path is located under the following example path: /home/myusername/myworkspace/hptargetpath/src/pages Considering the following symbolic link mapping: #ls -l /opt/share/www/mydevelopmentrootpath: lrwxrwxrwx 1 root root 77 2011-02-13 18:53 /opt/share/www/mydevelopmentrootpath -> /home/myusername/myworkspace/hptargetpath/src/pages With this folder mapping, I configured Apache HTTPd with the following configuration: <VirtualHost *:*> ServerName local.server.com ServerAdmin [email protected] DirectoryIndex index.html DocumentRoot /opt/share/www/mydevelopmentrootpath <Directory /opt/share/www/mydevelopmentrootpath/ > Options +Indexes Options +FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> </VirtualHost> But, I'm receiving a 403 Forbidden error when I want to access index.html under the address http://local.server.com/index.html. 403 Forbidden You don't have permission to access /index.html on this server. On httpd debug log, I checked the following message: [Sun Feb 13 19:34:47 2011] [error] [client 127.0.1.1] Symbolic link not allowed or link target not accessible: /opt/share/www/mydevelopmentrootpath I'm thinking that this problem is been generated by some path permission. It's not a direct permission to directory, but some intermediate directory in the path. There's a directive on httpd core Options: SymLinksIfOwnerMatch The server will only follow symbolic links for which the target file or directory is owned by the same user id as the link. But, I tested it without effects. Somebody may help me? I think that it's a trivial configuration on development environment. Best regards, And Past

  Read the article

• MySQL password changed every other day in windows?

  - by PHP

  Every morning when I check server status,I will find MySQL's password is changed: mysql -uuser -ppassword will report ERROR 1045 (28000): Access denied for user 'user'@'localhost' (using password: YES) And then I restart server,and when it's up,MySQL will be back to normal. It has now become a routinely job. What can be the cause for this? How can I know what's exactly happening to MySQL? Here is the error log: 100122 10:11:16 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100122 10:11:16 InnoDB: Starting shutdown... 100122 10:11:18 InnoDB: Shutdown completed; log sequence number 0 22939338 100122 10:11:18 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100122 10:12:40 InnoDB: Started; log sequence number 0 22939338 100122 10:12:42 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100123 16:20:44 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100123 16:20:44 InnoDB: Starting shutdown... 100123 16:20:46 InnoDB: Shutdown completed; log sequence number 0 22939832 100123 16:20:46 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100123 16:22:09 InnoDB: Started; log sequence number 0 22939832 100123 16:22:11 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL) 100125 9:18:59 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Normal shutdown 100125 9:18:59 InnoDB: Starting shutdown... 100125 9:19:00 InnoDB: Shutdown completed; log sequence number 0 22941001 100125 9:19:00 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: Shutdown complete 100125 9:20:22 InnoDB: Started; log sequence number 0 22941001 100125 9:20:25 [Note] D:\MySQL\MySQL Server 5.0\bin\mysqld-nt: ready for connections. Version: '5.0.24-community-nt' socket: '' port: 3306 MySQL Community Edition (GPL)

  Read the article

• FastGate A20 Line And Himem.sys Issue With Updating BIOS

  - by Boris_yo

  I have been persistent with a thought to perform my first BIOS update ever through MS-DOS but have been postponing this task until today. Despite people telling me any bootable ISO will do it either through CD-ROM or RAMDRIVE, I am still having problems. First is the problem with CD-ROM driver trying to make it work with 4 driver files (cd1.SYS, cd2.SYS, cd3.SYS, cd4.SYS) as well as starting RAMDISK proved to be failure: CD-ROM XMS Allocation Error RAMDISK XMS Allocaton Error (X: and R: drives not working) This A20 line seemed to be the obstacle which then after a couple of searches pointed me to this article on Microsoft website. It seems that FastGate is the culprit which takes over A20 line and conflicts with himem.sys which should be handling it causing the driver to be unable to allocate memory resources. Albeit article suggests 2 workarounds which is disabling FastGate option or adding switch, I read that the former workaround could cause problems which involves later tinkering BIOS, disabling shadow copy etc. while the latter workaround can just hang system as stated in the link above. I assume it just hangs the boot process from image file though. Summing up the above, I am cautious and think it is risky to follow both workarounds because disabling FastGate or trying adding switch by trying available switches from 1-14 or 16, could crash the BIOS update process by itself. I could do this without the need for himem.sys with bootable USB thumbdrive by making it to be seen as USB-HDD, but some time ago I read that it is never a good idea to update BIOS from hard drive so even thought it is simulation, who knows... Maybe it will deactivate hard drive in the middle of the BIOS update process or even USB thumbdrive per se? One forum discussion was about updating BIOS and somebody suggested to not load himem.sys for some reason, but now that I think of it, what if BIOS update needs upper memory?

  Read the article

• Printing on Windows 8 with PDF viewer (Adobe Reader) from network

  - by Bongo

  i have a problem with the Adobe Reader 8, but the problem seems to be equally bad with other pdf viewers. Here is the configuration: My PDF viewer is located on network drive "Z:" which is the network adress \dgs-main\progs. I tried to start the adobe reader from here - \\dgs-main\progs\Adobe\Reader 8.0\Reader\AcroRd32.exe and open the PDF from here - C:\Users\ServiceDesk\AppData\Local\Temp\GeneratedPDF.pdf The problem is as follows, if i open the PDF with a local PDF viewer everything works fine and i can print the document. If i open the PDF with the Network PDF viewer then it opens, but printing is impossible. The error message states: "Unable to start print job. Is printer available?" As mentioned above, it works with a local pdf viewer. In both cases i use the same printer. The Printer is a network printer but even with a local printer it fails. The error occurs only on Windows 8 machines. On windows 7 it works fine. I Hope somebody can tell me what the problem is. Thanks in advance and have a fine day.

  Read the article

• Windows 7 won't boot from any bootloader except for Windows Boot Manager after partition resize

  - by user2468327

  I have a triple boot system on a single SSD: OSX, Windows 7, and Ubuntu. I use Chimera (basically another version of Chameleon) as my bootloader. Usually I can boot all 3 OSs without any issue, but after using GParted to make my Ubuntu partition 2 Gigs larger, Windows 7 throws me an error when trying to boot to it from either Chimera or Grub. The error is consistently: `0xc000000e can't find \Boot\BCD" (slightly paraphrased). However, I can still get into Windows by selecting Windows Boot Manager from the boot options in my BIOS. I've already tried several known fixes for similar issues, including bootrec /rebuildbcd (and variations), and BootRec.exe/fixMBR + BootRec.exe/fixBoot. I've also tried Chkdsk. At best this has made it so Windows 7 boots on its own by default (making me have to reinstall Chimera and change back my boot settings in the BIOS). At worst this made it so Windows won't boot period. Now I'm back full circle where I started. A detail that might be useful is that bootrec /rebuildbcd says that the number of found Windows installations is 0. I'm fairly certain that I don't have a hybrid MBR. Mainly because I have a UEFI BIOS, and with that, it appears each OS can support a GPT. So it would kind of pointless to have and deal with. I may be wrong though, I couldn't find any way of finding out for sure online. However, I know for sure that the version of Windows I have installed is the UEFI version, as well as every partition tool I've used to look at my boot drive tells me it's GPT. How do I get it back so I can boot Windows 7 through another bootloader so I don't have to manually select it in the BIOS? Preferably without a reinstall.

  Read the article

• Connecting to my home router web interface from work

  - by Joe

  Hi, I'm trying to connect to my home router web interface from work. I use dyndns, because I don't have a static IP at home, and it works perfectly from any other place except my workplace (update: I made a mistake, see edit below). When trying to access the web interface from work I get a "500 Server Error" with the code: SERVER_RESPONSE_RESET. I'm not trying to use any protocols such as remote desktop, I'm only trying to access the web interface. I can access any other web page from my workplace with no problems, and I think my router web interface is like any other web page, isn't it? I thought maybe my work place proxy blocks addresses of services like dyndns, so I also applied another trick. Since I have a web page on my own domain (say www.mydomain.com) which I can access from work, I tried adding a CNAME to my domain which is linked to the dyndns address (router.mydomain.com). This way if anyone enters the address router.mydomain.com from anywhere, they reach my home router web interface, and there's no way of knowing it's a dyndns address (or is there?). However, it still doesn't work from my workplace (I get the same error message). Any ides? Edit: I'm sorry to say I made a mistake earlier. I used to be able to access my home router web interface from my old workplace, and I thought it was still possible since I don't recall making any configuration changes. However, after reading the replies, I went over to my old workplace and checked, and it doesn't work from there either. I'm very sorry for giving out wrong and misleading information about my problem. So to summarize: my problem is that I can't access my home router web interface from anywhere.

  Read the article

• What is auto-mounting my media volume?

  - by user285277

  Something is repeatedly mounting my "media" share, doing something with it, then quietly un-mounting it with no notifications at the user level. from the little I can gleaned from the console messages below, I thought I'd managed to stop it, if not understand it last night when I followed instructions for deleting all traces of the Google Update Daemon. I've not been using any Google apps whatsoever, so I was surprised to see that in Console. What's more surprising, and perhaps a little distressing, is that the same thing occurred this evening, when the Google Daemon is long gone. I don't have that log because I can't recall precisely what time it occurred. I'll do a search and provide it if you wish, though. In the meantime, any help with this would be extremely appreciated. I've asked over at Apple Discussions but I think it might be a little deeper than those manning the boards this weekend are comfortable with. It's certainly beyond my meager skills. With apologies in advance if this is more lines thank you need. Please note that I've transformed the Google links a little because the forum here requires more reputation points before one can post more than two links. 12/27/13 10:47:31.000 PM kernel[0]: memorystatus_thread: idle exiting pid 53629 [distnoted] 12/27/13 10:48:10.433 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 0; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.434 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 1; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.950 PM com.apple.SecurityServer[17]: Session 103257 created 12/27/13 10:48:34.328 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 2; not stale; error: The file doesn’t exist. 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount: /Volumes/Media Archive-1, pid 53641 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount : succeeded on volume 0xffffff80d6355008 /Volumes/Media Archive-1 (error = 0, retval = 0) 12/27/13 10:49:32.000 PM kernel[0]: wlEvent: en0 en0 Link DOWN virtIf = 0 12/27/13 10:49:32.000 PM kernel[0]: AirPort: Link Down on en0. Reason 8 (Disassociated because station leaving). 12/27/13 10:49:32.000 PM kernel[0]: en0::IO80211Interface::postMessage bssid changed 12/27/13 10:49:33.681 PM configd[16]: network changed: v4(en0-:10.0.1.12) DNS- Proxy- SMB 12/27/13 10:49:33.697 PM configd[16]: network changed: DNS* Proxy 12/27/13 10:49:35.475 PM KernelEventAgent[57]: tid 00000000 received event(s) VQ_NOTRESP (1) 12/27/13 10:49:35.000 PM kernel[0]: ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0xffffff802176b4a0 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect started /Volumes/Media Archive-1 prevTrigger 0 currTrigger 1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: posting to KEA EINPROGRESS for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: Max reconnect time: 600 secs, Connect timeout: 15 secs for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 1 seconds and then try again 12/27/13 10:49:35.479 PM KernelEventAgent[57]: tid 00000000 type 'afpfs', mounted on '/Volumes/Media Archive-1', from '//Me@Capsule._afpovertcp._tcp.local/Media%20Archive', not responding 12/27/13 10:49:35.487 PM KernelEventAgent[57]: tid 00000000 found 1 filesystem(s) with problem(s) 12/27/13 10:49:36.692 PM com.bourgeoisbits.cloak.agent[14503]: NetworkProfile: (null), (null), (null) (Connected: NO, Airport: NO, Open: NO) [trusted] 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 2 seconds and then try again 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 4 seconds and then try again 12/27/13 10:49:41.000 PM kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=53662[GoogleSoftwareUp] clearing CS_VALID 12/27/13 10:49:42.102 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 2 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:42.113 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateProductID:] KSUpdateEngine updating product ID: "com.google.Keystone" 12/27/13 10:49:42.116 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 1 ticket(s). 12/27/13 10:49:42.121 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x531870 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x5302d0 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x534340 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:42.130 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x1a31a90 server=<KSOmahaServer:0x534340> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=1 activeTickets=1 rollCallTickets=1 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:42.292 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:42.296 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:42.299 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 8 seconds and then try again 12/27/13 10:49:43.152 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateAllProducts] KSUpdateEngine updating all installed products. 12/27/13 10:49:43.153 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 2 ticket(s). 12/27/13 10:49:43.158 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x18367a0 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x1837e10 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 >, <KSTicket:0x1834750 productID=com.google.talkplugin version=4.7.0.15362 xc=<KSPathExistenceChecker:0x1833890 path=/Library/Application Support/Google/GoogleTalkPlugin.app> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x52e930 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:43.159 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x53a210 server=<KSOmahaServer:0x52e930> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=2 activeTickets=1 rollCallTickets=2 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> <o:app appid="com.google.talkplugin" version="4.7.0.15362" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone, ... (2)) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:43.244 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:43.247 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:43.250 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:45.570 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 1 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 10 seconds and then try again 12/27/13 10:49:53.828 PM KernelEventAgent[57]: tid 00000000 unmounting 1 filesystems 12/27/13 10:49:53.000 PM kernel[0]: AFP_VFS afpfs_unmount: /Volumes/Media Archive-1, flags 524288, pid 57 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: get the reconnect token 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: GetReconnectToken failed 32 /Volumes/Media Archive-1 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_unmount : afpfs_DoReconnect sent signal for unmount to proceed 12/27/13 10:50:12.104 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon main] GoogleSoftwareUpdateDaemon inactive, shutdown. 12/27/13 10:50:29.396 PM Dock[93157]: no information back from LS about running process

  Read the article

• AD domain on web servers behind NAT - DNS issues?

  - by Ant

  I'm trying to setup an AD domain to manage the security between two Windows Server 2008 webservers that will sooner or later use NLB to balance website requests. I've hit a problem which I think is a simple solution and is down to DNS. My website domain is mydomain.com. The two servers are running behind a NAT firewall on the 10.0.0.0 IP range. I've setup the AD domain to be called ad.mydomain.com (as recommended by MS and a few other answers to questions on here). The second web server however doesn't want to join the domain, and gives an error pinning the problem on DNS - "ensure that the domain name is typed correctly" even though it queries the SRV record successfully and gets the correct DC back - dc.ad.mydomain.com. Doing a dcdiag /test:dns on the DC gives the Delegation error 'DNS Server dc.mydomain.com Missing glue A record'. I have a feeling I need to add something to the public DNS so that it in some way knows about ad.mydomain.com. Can anyone suggest whether I'm on the right track in adding something to the public DNS? Or whether it's something else? Many thanks

  Read the article

• how to setup .ssh directory inside an encrypted volume on Mac OSX and still have public key logins?

  - by Vitaly Kushner

  I have my .ssh directory inside an encrypted sparse image. i.e. ~/.ssh is a symlink to /Volumes/VolumeName/.ssh The problem is that when I try to ssh into that machine using a public key I see the following error message in /var/log/secure.log: Authentication refused: bad ownership or modes for directory /Volumes Any way to solve this in a clean way? Update: The permissions on ~/.ssh and authorized_keys are right: > ls -ld ~ drwxr-xr-x+ 77 vitaly staff 2618 Mar 16 08:22 /Users/vitaly/ > ls -l ~/.ssh lrwxr-xr-x 1 vitaly staff 22 Mar 15 23:48 /Users/vitaly/.ssh@ -> /Volumes/Astrails/.ssh > ls -ld /Volumes/Astrails/.ssh drwx------ 3 vitaly staff 646 Mar 15 23:46 /Volumes/Astrails/.ssh/ > ls -ld /Volumes/Astrails/ drwx--x--x@ 18 vitaly staff 1360 Jan 12 22:05 /Volumes/Astrails// > ls -ld /Volumes/ drwxrwxrwt@ 5 root admin 170 Mar 15 20:38 /Volumes// error message sats the problem is with /Volumes, but I don't see the problem. Yes it is o+w but it is also +t which should be ok but apparently isn't. The problem is I can't change /Volumes permissions (or rather shouldn't) but I do want public key login to work. First I thought of mounting the image on other place then /Volumes, but it is automaunted on login by standard OSX mounting. I asked about it here: How to change disk image's default mount directory on osx The only answer I got is "you can't" ;) I could hack my way around, by writing some shellscript that will manually mounting volume at a non-standard location but it would be a gross hack, I'm still looking for a cleaner way to do what I need.

  Read the article

• Trouble with backslash characters and rsyslog writing to postgres

  - by Flimzy

  I have rsyslog 4.6.4 configured to write mail logs to a PostgreSQL database. It all works fine, until the log message contains a backslash, as in this example: Jun 12 11:37:46 dc5 postfix/smtp[26475]: Vk0nYDKdH3sI: to=<[email protected], relay=----.---[---.---.---.---]:25, delay=1.5, delays=0.77/0.07/0.3/0.35, dsn=4.3.0, status=deferred (host ----.---[199.85.216.241] said: 451 4.3.0 Error writing to file d:\pmta\spool\B\00000414, status = ERROR_DISK_FULL in "DATA" (in reply to end of DATA command)) The above is the log entry, as written to /var/log/mail.log. It is correct. The trouble is that the backslash characters in the file name are interpreted as escapes when sent to the following SQL recipe: $template dcdb, "SELECT rsyslog_insert(('%timereported:::date-rfc3339%'::TIMESTAMPTZ)::TIMESTAMP,'%msg:::escape-cc%'::TEXT,'%syslogtag%'::VARCHAR)",STDSQL :syslogtag, startswith, "postfix" :ompgsql:/var/run/postgresql,dc,root,;dcdb As a result, the rsyslog_insert() stored procedure gets the following value for as msg: Vk0nYDKdH3sI: to=<[email protected], relay=----.---[---.---.---.---]:25, delay=1.5, delays=0.77/0.07/0.3/0.35, dsn=4.3.0, status=deferred (host ----.---[199.85.216.241] said: 451 4.3.0 Error writing to file d:pmtaspoolB The \p, \s, \B and \0 in the file name are interpreted by PostgreSQL as literal p, s, and B followed by a NULL character, thus early-terminating the string. This behavior can be easiily confirmed with: dc=# SELECT 'd:\pmta\spool\B\00000414'; ?column? -------------- d:pmtaspoolB (1 row) dc=# Is there a way to correct this problem? Is there a way I'm not finding in the rsyslog docs to turn \ into \\?

  Read the article

• Coffee spilled inside computer, damaged hard drive

  - by Harpreet

  Today coffee spilled over my table, and some of it (very less) reached the PC case placed under the table. I think little bit of it got inside the PC case through the front. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help!! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• SSL timeout on some sites, across all browsers, on Mac OS X Snow Leopard

  - by dansays

  For the past several weeks, I've been receiving "Error 7 (net::ERR_TIMED_OUT): The operation timed out" when I attempt to connect to either Twitter or Paypal via SSL. I get this specific error in Google Chrome, but the same problem occurs in both Safari and Firefox. Other sites work fine, and other computers on my network can access these two sites. I have no firewall settings that would prevent me from accessing these sites over port 443. I notice that both Twitter and Paypal both have "Verisign Class 3 Extended Validation SSL CA" certificates. It is unclear whether this is related to the problem. In an effort to troubleshoot, I attempted to open the test sites referenced on Verisign's root certificate support page, which worked fine. Just to be sure, I downloaded and installed the root package file and installed all included Verisign certificates. No joy. I feel like I've hit a dead end. Any ideas? Update the first: I also cannot connect to FedEx.com, who also has a Verisign Class 3 Extended Validation cert. Update the second: Aaaaaaand it fixed itself. I did nothing. Or, I did something that worked, but in a delayed fashion. Frustrating, but a win is a win. I'll take it.

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• Subdomains not working with virtual hosts on apache2 ubuntu

  - by cy834sh4rk

  I'm trying to set up a subdomain on my ec2 account but can't figure out what's going on. I've looked for a few hours and haven't been able to find an answer :-/ I'm trying to set up a subdomain using virtual hosts but no matter what I try the browser can't find the subdomain :-( I have the following vhosts files set up: apache2/sites-available/mysite (this site currently works) <VirtualHost *:80 ServerName mysite.com ServerAdmin webmaster@localhost DocumentRoot /home/sites/mysite <Directory /home/sites/mysite Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory ErrorLog ${APACHE_LOG_DIR}/mysite-error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/mysite-access.log combined </VirtualHost apache2/sites-available/red (this is the subdomain I'm trying to set up) <VirtualHost *:80 ServerName red.mysite.com ServerAdmin webmaster@localhost DocumentRoot /var/www/red <Directory /var/www/red Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory ErrorLog ${APACHE_LOG_DIR}/red-error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/red-access.log combined </VirtualHost Apache mod_rewrite is enabled. I've enabled both sites using a2ensite and I make sure I restart apache every time I make a change. /etc/hosts 127.0.0.1 localhost 127.0.0.1 mysite.com 127.0.0.1 red.mysite.com Any help would be appreciated. Thanks!

  Read the article

• How to Re-install an App that Shows up in the Appstore as 'Update' Instead of 'Buy App'

  - by Craig Reville

  So long story short: I dropped the wrong app into 'clean my mac' and I hit 'cancel' but it was too late by that point. I rebooted and appstore said it had an update, when I opened appstore it was showing an update for the app I just uninstalled. I tried clicking 'update' but it gives me an error saying it's unable to install after 'downloading'. When I try to go into 'purchased apps' it shows the app as uninstalled so I click 'install' and I get an error saying it's already installed. I'm running Lion OS X, latest version, updated, mac book pro is only a few months old. I tried searching through the entire system to remove all traces of the app, after rebooting appstore no longer shows the app and no longer shows the update but on the apps page it still says 'Update'. I tried reinstalling the app from desktop OUT of the appstore and again says the app is 'already installed'. So after reading more about lion I found an article that spoke about 'BundleID' being the thing that tells appstore what's installed and needing updating however I can't find the location of where the BundleID would be. Any thoughts? I've tried CCleaner, AppCleaner etc and none of them show the app, mainly because it is uninstalled. Update I've spoken to Apple Support who confirmed that there is a file in the system that connects separately to tell the system if there are updates available however they declined to inform me of any further details. Apple also referred me from technical support to iTunes App Store opposed to Mac App Store support and from there I have been referred to AppleCare who are currently 'investigating' this issue. Hopefully there will be a fix that's simple to implement for people having similar issues, this appears to be a more common issue than I previously thought.

  Read the article

< Previous Page | 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044  | Next Page >