Search Results

Search found 10207 results on 409 pages for 'ethernet switch'.

Page 109/409 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

  • Slow write speeds on new Gigabit home file server

    - by Ryan Holder
    So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

    Read the article

  • Is there DBus command to set position of KDE panel?

    - by Liss
    I have single vertical KDE panel. When I switch from single monitor X screen back to triple monitor X screen (with xrandr) my KDE panel ends up on the right edge of middle monitor, instead of right edge of right monitor. Also, many windows are in wrong place after the switch, but I have a script which restores geometry of all windows (as is used to be in triple monitor state before I switched to single monitor mode), so this is not a problem. Unfortunately, it does not work for KDE panel - it stays in the wrong place. I guess I need to use DBus to restore KDE panel position (programmatically move it to right edge of right screen), I tried googling, but it seems it is not very well documented. Is there DBus command to set position of KDE panel?

    Read the article

  • Find and raise a window in KDE4 with shortcut

    - by Andre_112
    Hi all! I was wondering about a possibility to find and raise some window in KDE4 with shortcut. Currently in KDE 4.4 there is a possibility to switch to window from krunner (Alt-F2). Say, I have an open konsole widow somewhere and to switch to it, I can Alt-F2, write konsole and choose konsole window I need from the list. This is great, but too much typing. I would like to have a keyboard shortcut to do the same. Maybe some DBUS magic can do that? Any ideas? Thaks! Andre

    Read the article

  • zero downtime during database scheme upgrade on SQL 2008

    - by eject
    I have web application on IIS7 with SQL server 2008 as RDBMS. Need get 0 downtime during future upgrades of ASP.NET code and DB schema as well. I need to get right scenario for this. I have 2 web servers and 2 sql servers and one http load balancer whcih allows to switch web backend server for web requests. Main goal is to make 1st web server and DB server up and running, update code and db schema on 2nd server and then switch all the requests to 2nd server and then main problem - how to copy data from 1st database 2nd (which was changed during upgrade).

    Read the article

  • esx 4 - c7000 - cisco 3020

    - by gdavid
    I have 4 blades with esx 4 installed in a HP c7000 enclosure. They have 6 cisco 3020 for hp switches in the backend. The plan was to use 2 switches for iSCSI traffic and the other 4 for data traffic. I am having a problem trunking the switches to our existing environment. The documentation i keep finding online has commands/features that are not available on the 3020 switch. Does anyone have this setup anywhere? I am looking to do Virtual Switch Tagging (VST) so i can control the machines vlan via the port groups. The only time any configuration worked for us was when our network team placed the command switchport native vlan x this setup only allowed vlan x to pass traffic and only when the port group was in vlan 0. Ideas? thanks for any help. -GD

    Read the article

  • Is it possible to use multi keyboards with multi keyboard layouts simultaneously?

    - by mono
    Considering to switch to dvorak layout, but this terminal is used by multi users as the same user account. It is unacceptable to ask all people to switch layout, plus it is hard to use dvorak layout with a keyboard qwerty-ly labeled. But there are spare (USB,qwerty) keyboards, so if I plug another keyboard in and be able to use multi layouts on different psyical keyboard simultaneously (I will rearrange letters on keys), the problem get solved. solution for either windows or linux is fine. anyway thanks all.

    Read the article

  • Connecting guest OS to host os internet connection hyper-v

    - by autrevo
    Hyper-V internal switch and VM OS interfacing with Guest OS and IP Cofiguration When configuring hyper-v internal switch, Apart from physical lan adapter (say adapter 1), I see another LAN adapter (say adapter 2) added in host os. And we already have one virtual lan adapter in guest os, (say adapter 3) . adapter 1 is connected to internet with defaulty gateway say, 192.168.0.254 and uses class C IP. By con configuring adapter 2 and 3, I need to acheive two purpose - Access internet in guest os. seemlessly share files & folders between guest and host OS. Please, suggest, What is the best way to configure IP of these three adapters ?

    Read the article

  • Does a single LACP channel over multiple switches increase redundancy?

    - by Sirch
    I am curious for opinions, findings, or evidence that having multiple interfaces bonded using LACP to ports in multiple switches can increase redundancy. Previously bonded interfaces have always been to a single switch, with a redundant channel to another port. Without getting into vendor specifics, my thought is that as this is a single LACP, the likelihood that an event or change could lead to a wide service outage. Without having the spare equipment or time to test this single channel over diverse switches, could anyone with a greater networking knowledge than myself, tell me if there a network side event that would bring down the network connectivity to a server that had created a bonded interface to two ports on separate switches? Does the use of bonded ethernet channels across multiple switches (that we are advised that we can use) from the server, provide both improved throughput (unquestionably), and improved redundancy (uncertain). Could/would network events such as switch failure, port migration, patching, recovery, etc, cause the channel for both server network interfaces to be unavailable? Thanks in advance.

    Read the article

  • How do I stop someone from saturating my line & wasting CPU cycles

    - by JoshRibs
    My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

    Read the article

  • Windows 7 ipv4 autoconfiguration - cannot connect to internet

    - by GuiccoPiano
    I get my internet connection from a guy (lets call him my service provider henceforth). He gives internet connections to many students here in my hostel. My PC gets a private IP through his DHCP server. Now, when I switch on my WiFi, my PC gets a private IP as it should and I can connect to the internet just fine. But now when I connect my LAN cable, my PC gets some "Autoconfiguration IPv4 address" 169.254.110.154(Preferred) and I cannot connect to the internet. Here is the ipconfig /all output for ethernet port: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8059 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : <<MAC DISPLAYED HERE>> DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5054:a347:7d06:6e9a%11(Preferred) Autoconfiguration IPv4 Address. . : 169.254.110.154(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 285222078 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-50-AC-68-54-42-49-EE-52-16 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled I also tried: Start a command prompt as admin. Run "netsh winsock reset" Run "netsh interface ipv4 reset" Run "netsh interface ipv6 reset" Restart your computer. All this does not work. Any idea to solve the problem?

    Read the article

  • How to block all multicast traffic travelling through a Cisco Catalyst 3750

    - by TrueDuality
    Something changed today. I can't seem to track down what, but one of our 3750s decided that it was going to forward all the multicast traffic it saw from the ghost server across every VLAN it has. I've tried writing a simple access group that consists of the following: access-list 100 deny ip any 224.0.0.10 0.0.0.255 access-list 100 permit ip any any I apparently mistakenly assumed that once applied to an interface that it would block all of the multicast traffic on that interface regardless of VLAN. I do not want any multicast traffic flowing through this particular switch to any VLAN or even to stay on the same VLAN beyond this switch. Does anyone have any ideas?

    Read the article

  • Can a Linux system crash cause network issues?

    - by Supratik
    I have a Ubuntu box in my network which crashed, all the system connected to the switch in which the Ubuntu system was connected started giving problem. I removed that system from the network, since that was the last change I made in my network and everything was fine. So, to confirm this I again connected the system back to the network and the same network outage happened. When I checked the links it was fine. When I rebooted the problematic system and again connected back to the network switch everything started working. I think possibly the crash of the Ubuntu system could have caused this outage. Is there any possibility that a kernel crash can cause network issues?

    Read the article

  • solaris + why cant ping to default getway

    - by yael
    I have Solaris machine with IP 10.10.10.100 and default getway 10.10.10.1 and subnet 255.255.255.0 remark - solaris machine connected to cisco switch via cross cable and from switch to my laptop I configure my laptop to connect to my Solaris machine so my laptop IP is 10.10.10.1 and subnet 255.255.255.0 but something not clearly I have ssh connection from my laptop to my Solaris machine ( I mean I in my solaris machine ) but from Solaris machine I can do ping to 10.10.10.1 ? ( how it can be ??? ) please advice why?

    Read the article

  • Computer hangs on start-up, but re-start always works

    - by user10604
    I press the power switch; the fans start whirring; then precisely nothing happens. The monitor lights (I have two monitors) blink to indicate that they aren't receiving any signal - no BIOS splash screen, nothing. This scenario occurs about 80 percent of the time, the other 20 percent being normal starts. Noticing that the computer has not started properly, I press the power switch for four seconds to turn the computer off, and then I press it again to start the computer for the second time. It always starts normally the second time. Always. The power supply is a 750W from SilverStone. The motherboard is a Gigabyte P55A-UD3P. The video card is an Asus EN9800GT. There's 8 GB of RAM. I don't know what other information might be pertinent. Help!

    Read the article

  • How to open a program on particular desktop?

    - by Vi
    When I start GUI program, it's window appears appears on currently active desktop (essentially, on random desktop). How to make it to appear on the specified desktop? For example, at startup I want certain programs to be started and distributed to desktops. I've already set up config file of openbox to force some programs to always start on specific desktop. Ideally it should be like: start_on_desktop 1 gnome-terminal --tab -e program1 --tab -e program2 start_on_desktop 2 gnome-terminal --tab -e program3 --tab -e program4 start_on_desktop 3 firefox It should be able to start the same program on other desktop. Also dislike when I start program while being on desktop X then switch to desktop Y and SUDDENLY a program which should be on X appears on Y. When I start lots of programs on and switch often between desktops they end up being in chaos and I need to collect them together and redistribute sanely. Also I want the first initial gnome-terminal to be on desktop 3, but I also want subsequent gnome-terminals to be on the desktop where I pressed the keystroke (also configured in openbox) that launches gnome-terminal.

    Read the article

  • Wireshark does not see interfaces (winXP)

    - by bua
    Short story: Wireshark is working....on my winXP-32b ... usage .... Long long time later Wireshark does not work It can't find any usefull interface (just VPN) ipconfig /all Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1490 Dual Band WLAN Mini-Card Physical Address. . . . . . . . . : SOME VALID MAC Ethernet adapter eth0: Connection-specific DNS Suffix . : xxxx Description . . . . . . . . . . . : Broadcom 440x 10/100 Integrated Controller Physical Address. . . . . . . . . : SOME VALID MAC Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.12.68 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168..... ..... Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Fortinet virtual adapter Physical Address. . . . . . . . . : SOME VALID MAC Following steps didn't help: Several Wireshark re-installation Several LIBPCAP re installation SP3 for winXP Any ideas welcome.

    Read the article

  • Should I go along with my choice of web hosting company or still search?

    - by Devner
    Hi all, I have been searching for a good website hosting company that can offer me all the services that I need for hosting my PHP & MySQL based website. Now this is a community based website and users will be able to upload pictures, etc. The hosting company that I have in mind, currently lets me do everything... let me use mail(), supports CRON jobs, etc. Of course they are charging about $6/month. Now the only problem with this company is that they have a limit of 50,000 files that can exist within the hosting account at any time. This kind of contradicts their frontpage ad of "UNLIMITED SPACE" on their website. Apart from this, I know of no other reason why I should not go with this hosting company. But my issue is that 50,000 file limit is what I cannot live with, once the users increase in significant number and the files they upload, exceed 50,000 in number. Now since this is a dynamic website and also includes sensitive issues like payments, etc. I am not sure if I should go ahead with this company as I am just starting out and then later switch over to a better hosting company which does not limit me with 50,000 files. If I need to switch over once I host with this company, I will need to take backups of all the files located in my account (jpg, zip, etc.), then upload them to the new host. I am not aware of any tools that can help me in this process. Can you please mention if you know any? I can go ahead with the other companies right now, but their cost is double/triple of the current price and they all sport less features than my current choice. If I pay more, then they are ready to accommodate my higher demands. Unfortunately, the company that I am willing to go with now, does NOT have any other higher/better plans that I can switch to. So that's the really really bad part. So my question(s): Since I am starting out with my website and since the scope of users initially is going to be less/small, should I go ahead with the current choice and then once the demand increases, switch over to a better provider? If yes, how can I transfer my database, especially the jpg files, etc. to the new provider? I don't even know the tools required to backup and restore to another host. (I don't like this idea but still..) Should I go ahead and pay more right now and go with better providers (without knowing if the website is going to do really that well) just for saving myself the trouble of having to take a backup of the 50,000 files and upload to a new host from an old host and just start paying double/triple the price without even knowing if I would receive back the returns as I expected? Backup and Restore in such a bulky numbers is something that I have never done before and hence I am stuck here trying to decide what to do. The price per month is also a considerable factor in my decision. All these web hosting companies say one common thing: It is customers responsibility to backup and restore data and they are not liable for any loss. So no matter what hosting company that I would like to go with, they ask me to take backup via FTP so that I can restore them whenever I want (& it seems to be safer to have the files locally with me). Some are providing tools for backup and some are not and I am not sure how much their backup tools can be trusted considering the disclaimers they have. I have never backed-up and restored 50,000 files from one web host to another, so please, all you experienced people out there, leave your comments and let me know your suggestions so that I can decide. I have spent 2 days fighting with myself trying to decide what to do and finally concluded that this is a double-edged sword and I can't arrive at a satisfactory final decision without involving others suggestions. I believe that someone must be out there who may have had such troublesome decision to make. So all your suggestions to help me make my decision are appreciated. Thank you all.

    Read the article

  • Network based on Netgear FVS318 extremely slow

    - by Fentible
    A network I maintain uses an FVS318 as a router, with a separate switch. Communication within the network is slow. Out to the internet is even slower. As it stands there is one patch from the FVS to the switch and no other devices directly connected to the FVS because any that are run so slowly they might as well not be connected to the network. Swapping in a bog-standard home router dramatically increases network speed, but that's not a viable solution because some of the enterprise features of the FVS are required. There are quite a few complaints about this on the Netgear forum, but Netgear support have not been forthcoming with any help - so I turn to you all: any ideas?

    Read the article

  • How to open a program on particular desktop?

    - by Vi.
    When I start GUI program, it's window appears appears on currently active desktop (essentially, on random desktop). How to make it to appear on the specified desktop? For example, at startup I want certain programs to be started and distributed to desktops. I've already set up config file of openbox to force some programs to always start on specific desktop. Ideally it should be like: start_on_desktop 1 gnome-terminal --tab -e program1 --tab -e program2 start_on_desktop 2 gnome-terminal --tab -e program3 --tab -e program4 start_on_desktop 3 firefox It should be able to start the same program on other desktop. Also dislike when I start program while being on desktop X then switch to desktop Y and SUDDENLY a program which should be on X appears on Y. When I start lots of programs on and switch often between desktops they end up being in chaos and I need to collect them together and redistribute sanely. Also I want the first initial gnome-terminal to be on desktop 3, but I also want subsequent gnome-terminals to be on the desktop where I pressed the keystroke (also configured in openbox) that launches gnome-terminal.

    Read the article

  • Cisco: changing VTP mode server/client to transparent

    - by J. Smith
    I have around 40 L2 switches (2960, 3560, 3500, 3750) running in VTP client mode and one L3 switch (6500) running in VTP server mode, all connected together. I would like to switch everything in VTP transparent mode without any interruption of service. I've already test on a poc version with 3 switches (Catalyst 2950, 3560 and 3750). Using serial and SSH connection, it is seems working but i'm not sure it is enough representative compare to the real network. Knowing that the VTP Pruning is enabled, I am wondering what would be the best procedure to proceed the changement. I've read that we could lost connection by keeping it enabled. Should I change the server or clients first? Is it important to change the VTP domain and VTP Pruning parameters?

    Read the article

  • The sound freezes while listening to music

    - by Scott
    I have bought an sound card - Sound Blaster X-FI Surround 5.1 PRO and while I'm listening to the music, after few minutes or even hours (it does happends randomly) the sound dissapears and I have to go settings: Playing Devices - Advanced and switch the Default Format (sampling frequency) and switch from the `16-bits, 48000 Hz (DVD Quality) to any other from the list (16-bits, 96000 Hz or 24-bits, 48000 Hz or 24-bits 96000 Hz). I have been trying to set all of the above options, but for all of them the sound freezes after listening to music. It is getting annoying and I hope its the settings fault and not my sound card. I got my drivers installed from the attached CD and I'm running Windows 7 HP 64 bits. If anyone would try to help me, I would really appreciate this.

    Read the article

  • Linux server failover

    - by Lukasz
    I have two Linux servers (CentOS6) - both are identically configured connected to the same switch with a direct link between them. I only have one external IP that is assigned to eth0 on both servers (connected to the internet switch) with the interface shutdown on server 2. How can I failover to server 2 if server 1 dies - as stated they are linked directly so they can check for availability of each other via ping/tcp/udp. I toyed with Heartbeat but the documentation seems to be non-existent - not sure how to bring up an interface and start some services if the other server dies.

    Read the article

  • Unauthorized computer use via keyboard or remote access?

    - by brydaverambo
    I’m suspecting my computer is being used when I’m not at home. This is happening either physically or remotely. My wireless switch is off. Is there any way possible to detect and/or monitor activity without purchasing software? My settings are being changed as well as passwords (Bios PW was changed and I cannot access Bios settings). I connect via the network cable. Is it possible for someone (in range) to connect to my laptop even if the wireless switch is off? This is a Dell Inspiron 1720 with the WLAN 1395 card. Here’s the kicker. When I try to download freeware for monitoring activity, I am not allowed to do this! ????

    Read the article

  • Trying to launch old game using wine

    - by rhon
    I'm using wine 1.5.11 on Archlinux, and I try to launch this old game : http://www.cnetfrance.fr/telecharger/waterboy-11006056s.htm?download=1 The problem is that I always get a "Run-time error '13' : Type mismatch" when I try to launch it. I've tried to switch oleaut.dll and ole32.dll to "native", and switch to "Windows 98" mode using winecfg, and then I had this error : err:module:import_dll Library ole32.dll (which is needed by L"Z:\\games\\WaterBoy\\MSVBVM50.DLL") not found err:module:import_dll Library OLEAUT32.dll (which is needed by L"Z:\\games\\WaterBoy\\MSVBVM50.DLL") not found err:module:import_dll Library MSVBVM50.DLL (which is needed by L"Z:\\games\\WaterBoy\\WaterBoy.exe") not found err:module:LdrInitializeThunk Main exe initialization for L"Z:\\games\\WaterBoy\\WaterBoy.exe" failed, status c0000135 I've installed vb5runtime using winetricks, but it didn't help. Am I doing something wrong ?

    Read the article

  • Remote Desktop connection breaks the wireless connection

    - by Michal Talaga
    When I connect to my Windows 8 Professional machine via Remote Desktop (RDP) I almost always get my WiFi connection broken. The setup: T61P Lenovo Laptop + W8 at home Wireless Router with NAT forwards connections to that machine Windows 7 laptop at work connecting to the home laptop When I connect, very often I get to login and suddenly connection is lost and I cannot reconnect again. When I get home I find my WiFi connection is still connected to the Access Point but does not function. Can't even ping the router. What is strange is that disabling wireless with the hardware switch and enabling it again doesn't help. The only way to make it works again: - Reboot - Disable wifi with hardware switch AND disable the network card in Device Manager, then enable both I did not have this problem on the very same laptop when it was running Windows 7. Any hint how can I find where the problem is?

    Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >