Search Results

Search found 11707 results on 469 pages for 'boot failure'.

Page 111/469 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

  • Identifying the cause of my DNS failure (domain not propagating)

    - by thejartender
    I have set up a DNS server with the help of two helpful tutorials: http://linuxconfig.org/linux-dns-server-bind-configuration http://ulyssesonline.com/2007/11/07/how-to-setup-a-dns-server-in-ubuntu/ I am using: Ubuntu Bind9 and had issues I tried negating on my own thanks to a question I posted here earlier that pointed out my mistake of using rfc 1918 addresses in my previous SOA record: $TTL 3D @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. $TTL 600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.10.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I read the ranges that are used under rfc 1918 and modified my routers resource pool to assign LAN devices IP(s) within the 30.0.0.0 range and now modified my SOA to: $TTL 600 @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 30.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 30.0.0.42 gw IN A 30.0.0.138 www IN CNAME thejarbar.org. $TTL600 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.30.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. I can ping my nameserverver ns.thejarbar.organd it gives me the correct isp IP address, but my domain never seems to propagate to my nameserver. I have searched for a concise tutorial that covers setting up a DNS with a nameserver that hosts (my) or the site. I am fully aware that this is not recommended and am using this for my learning purposes. Getting to the question, due to the lack of information in tutorials I looked at (nothing about rfc 1918 and no example of swapping these with ISP IP) is my router modification going to help me as it does not seem to be. I have also tried as recommended using my ISP IP instead of the values I posted. My site never propagated to my nameserver. What could be causing this? I have run dig thejarbar.org @88.89.190.171 and get an authorative response. Can anyone assist me with the final steps I may be missing here?

    Read the article

  • Mac failing (failed?) hard drive - is all hope lost?

    - by Daniel
    It's a 500 GB Seagate laptop hard drive that came with my Macbook Pro. Apple partition format. Already replaced and now have it external, connected via SATA/USB adapter. Trying to get just a few files that I worked on while out of town when it crashed (and thus did not have my time machine backup drive). Drive will not mount, but OS X Disk Utility detects it and can read the capacity, model number, and even the name of the partition, which leads me to believe all hope may not be lost. Failed attempts so far: Disk Utility verify+repair says drive cannot be repaired and that I should back up immediately (lovely) Disk Warrior says it cannot rebuild the directory due to hardware failure Data Rescue quick & deep scans immediately failed PhotoRec says "error reading sector" for every sector (at least for the few minutes I let it run before closing it to explore other options) What else can I try here? Again, I'm just looking for a few, small files (python scripts to be specific) - not a full recovery.

    Read the article

  • Galera install failure on Fedora 18

    - by ehime
    I've been trying to reinstall MariaDB and have been encountering multiple issues, $ yum install Mariadb-Galera-server Error: Package: MariaDB-Galera-server-5.5.29-1.i386 (mariadb) Requires: galera Available: galera-23.2.4-1.rhel5.i386 (mariadb) galera galera = 23.2.4-1.rhel5 You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest there is a requirement that libssl.so.6 and libcrypto.ssl.6 are installed, these DO show up in my /lib64 and /lib though as linked items. /usr/lib -rwxr-xr-x 1 root root 1356700 Nov 23 2010 libcrypto.so.0.9.8e lrwxrwxrwx 1 root root 19 Jun 28 12:03 libcrypto.so.6 -> libcrypto.so.0.9.8e -rwxr-xr-x. 1 root root 394272 Mar 18 14:22 libssl.so.1.0.1e lrwxrwxrwx 1 root root 16 Jun 28 12:03 libssl.so.6 -> libssl.so.0.9.8e /usr/lib64 -rwxr-xr-x 1 root root 1849680 Mar 18 14:21 libcrypto.so.1.0.1e lrwxrwxrwx 1 root root 26 Jun 28 11:54 libcrypto.so.6 -> /lib64/libcrypto.so.1.0.1e -rwxr-xr-x 1 root root 421712 Mar 18 14:21 libssl.so.1.0.1e lrwxrwxrwx 1 root root 23 Jun 28 11:54 libssl.so.6 -> /lib64/libssl.so.1.0.1e So the deps SHOULD be met, trying to $ yum install galera returns this Resolving Dependencies --> Running transaction check ---> Package galera.i386 0:23.2.4-1.rhel5 will be installed --> Restarting Dependency Resolution with new changes. --> Running transaction check ---> Package galera.i386 0:23.2.4-1.rhel5 will be installed --> Finished Dependency Resolution No errors? but no install either .... ? lets try wget and rpm'ing the package instead I guess? $ wget https://launchpad.net/galera/2.x/23.2.4/+download/galera-23.2.4-1.rhel5.x86_64.rpm $ rpm -ivh galera-23.2.4-1.rhel5.x86_64.rpm This issues the dreaded error: Failed dependencies: libcrypto.so.6()(64bit) is needed by galera-23.2.4-1.rhel5.x86_64 libssl.so.6()(64bit) is needed by galera-23.2.4-1.rhel5.x86_64 But we saw above these packages are here =( Whats going on?? Is openssl not installed? $ yum install openssl Loaded plugins: langpacks, presto, refresh-packagekit Package 1:openssl-1.0.1e-4.fc18.x86_64 already installed and latest version Nothing to do Its there.... ??? wth Fedora?

    Read the article

  • Doesn't boot after installing fglrx for ati 5650

    - by elivanja
    Hi, I'm a complete noob here, I recently bought an HP 3161 with an ATI 5650 hd card, when I installed 10.04 LTS everything was working fine until I was prompted to activate proprietary driver fglrx, after I did this I couldn't reboot (not even in recovery mode) until I reinstalled 10.04, what can I do? I would appreciate any help since I haven't been able to find anyone with the same problem, thanks.

    Read the article

  • Would hybrid drive work after SSD failure

    - by lulalala
    Hybrid hard drive combines SSD with traditional hard drives. I know that SSD can fail much often than traditional hard drives. So I want to ask that, when the SSD part of the hybrid drive fails, would I still be able to use the traditional hard drive? If it won't work like that, then I will consider add-in SATA cards instead, as it delegates risk much better. EDIT: I guess it differs from model to model, so if yes what models would work. (I am evaluating Seagate DX for now)

    Read the article

  • How to ensure nvidia_current module loads during boot

    - by Aras
    I am running Ubuntu 12.10 on an Asus G75V laptop with nvidia gforce GTX 660M. I first run 12.04 on this machine and was able to install nvidia_current drivers from swat ppa: sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current This worked in 12.04 and after rebooting the machine my graphics where working properly. After upgrade to 12.10 however, the machine boots into a low resolution desktop which I can not really interact with. I suspect this is due to the driver not being loaded properly. To fix this, I have to switch to ctrl+alt+F1 session and manually load the nvidia_current module and restart the desktop manager: sudo modprobe nvidia_current sudo service lightdm restart Now everything works fine again. However, I would like not to have to do this every time I reboot the machine. I also dont want to hack an script to do this on load. Basically, if things are setup currectly, the nvidia_current driver which is installed should load. How can I make sure nvidia_current driver module loads properly when system starts?

    Read the article

  • Laptop powering off after 10 mins or so

    - by Jack
    I have no OS installed, and I am trying to use a linux boot disc. However it is not a linux problem....if I just leave the computer on at the no operating system found message, it still turns off. I thought maybe it was overheating, but I am 90% sure that is not the problem. What else could cause this? I should have mentioned, it's a laptop.

    Read the article

  • How to start vnc server on-demand (not on boot)

    - by QRohlf
    I have a vps which has the basic xfce environment & tightvncserver installed. I would like to have tightvncserver automatically start whenever I initiate a connection to the port it runs on (in my case, 5901). I've seen posts about using inetd or xinetd to do this, but I've also seen lots of posts saying that (x)inetd is not included in Ubuntu for a reason, and that it's a bad idea to use it. Anyways, I'm looking for a way to auto-start tightvncserver whenever there's an incoming connection to port 5901, preferably with as few dependencies as possible

    Read the article

  • Drive stopped working on windows server 2003 and I receive a "controller error"

    - by Durden81
    I can access the server in safe mode. I have a Proliant 360 Hp server with Windows server 2003 R2. The event viewer is completely filled up with this error: the driver detected a controller error on Device\Harddisk3\DR3 I individuated the drive affected. It is drive H that is a secondary non mirrored drive. When I access anything on that drive I receive: "the request could not be performed because of an I/O device error" What should I do? Is this just a driver issue or a hard drive failure? Please give me a quick help as my websites are offline due to this. Any suggestion is welcome!

    Read the article

  • (monit) What does failure "Changed" mean

    - by bresc
    Hi, I installed monit on my server and tried to monitor nginx. check process nginx with pidfile /var/run/nginx.pid start program = "/etc/init.d/nginx start" stop program = "/etc/init.d/nginx stop" group server And I get Process 'nginx' status Changed monitoring status monitored data collected Wed Mar 24 00:37:49 2010 What does "Changed" mean? I couldn't find anything. Thx

    Read the article

  • Ubuntu does not boot after bad shutdown

    - by Molly Gibson
    I recently swapped from Windows7 to Ubuntu 11.10 due to problems with my Windows. Ubuntu worked great for a few days with no problem, This morning I ran out of battery and the laptop shut down. I rebooted it and now it just displays an error message ( black screen with coding commands) it doesn't even go onto the purple screen anymore. Any help on this would be much appreciated.. Ps: would installing Ubuntu again make any difference?

    Read the article

  • Computer powering off after 10 mins or so

    - by Jack
    I have no OS installed, and I am trying to use a linux boot disc. However it is not a linux problem....if I just leave the computer on at the no operating system found message, it still turns off. I thought maybe it was overheating, but I am 90% sure that is not the problem. What else could cause this?

    Read the article

  • TrueCrypt System Favorite Volume doesn't mount automatically on boot

    - by Anders Hovgaard
    I've encrypted my system partition using TrueCrypt and I've read that I can mount my encrypted data partition (TrueCrypt volume) on boot by making it a "System Favorite" and giving it the same password as the system partition. However it doesn't work and I have to mount it manually every time. See this example. I've tried enabling "Cache pre-boot authentication password in driver memory (for mounting of non-system volumes)" in System - Settings, but that didn't change anything either. Any ideas?

    Read the article

  • MySQL fault linked to windows shutdown failure?

    - by Roy
    As far as i understand my computer is experiencing a strange coincidence (hopefully it isn't and somebody can enlighten me). Basically i shut down my laptop (Windows 7) (at 17.20, today, to be precise) successfully (and so also did XAMPP and its included components). However upon starting my laptop up again in the last hour i noticed that the MySQL module service in my xampp control panel was not coming on (just a big red tick; incidentally everything else was working fine). Now, i had the exact same problem about two weeks ago, whereby i just reinstalled xampp and got it working again. But rather than doing this straight away i thought i would just restart my laptop first. However it won't restart (or shut down first) to be precise now. I can remember Windows wasn't shutting down properly the last time it happened (about two weeks ago). Just wondered if this coincidence pointed to any specific diagnostic as regards the problem with MYSQL? If so i would appreciate greatly any help. Otherwise sorry for wasting your time.

    Read the article

  • raid 0 failure, drives look fine

    - by Alan
    Hello, after a lovely blue screen my vista 64 machine decided to reconfigure one of my drives to no longer be part of my raid volume. So now my raid fails as it only has one member disk. This happened to me about 6 months ago and I just changed the disk in question back to a raid disk and all was well. However I cant seem to find that option in my bios or raid config anymore :( Any help would be appreciated

    Read the article

  • Freeze on Boot WindowsXP

    - by kyle
    Ok first off I know I should have Windows 7 but i don't Its a really old computer and i'm not sure if it can run the latest OS of ubuntu but i'm trying any whay so here are my specs or what i could have gathered from the computer(viruses are every where and most of the drivers are gone) Specs OS WindowsXP(it isn't letting me know which one that is blocked) Graphics card(can't access device manger it is blocked also) graphics card is 2003-2004 era though ram 512mb last time i checked USB(Drivers Gone) Wireless Card(Drivers Gone) Lan Card(Drivers Gone) Audio(Drivers Gone) CD Drive (it runs and works but i can't check its properties that's blocked to) Computer Dell Inspiron 600m Good News I have the Driver CD for everything Bad News I Don't have the OS CD I know the Computer is trash but i want to flash it anyway and just install linux(ubuntu) The second problem is it doesn't even want to load the CD all the way it is just stuck at the Ubuntu Screen with all the bubbles orange and if i resart it just does it again. any help would be nice. EDIT: okay i tried the first comment and it said i need a firmware file from http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware the firmware is b43/ucode5.fw, b43-open/ucode5.fw is there any other way of installing this firmware without being in the Ubuntu because what I have read is I need to be in Ubuntu to do this... Thanks for all the help you are giving me i have read your comments but i don't want to wait another two hours downloading that if i can get it working on this...

    Read the article

  • ADFS http login failure not re-requesting credentials

    - by Devnull
    We have ADFS working with HTTP (401) login. If a user types their password incorrectly, ADFS barfs and requires that the browser be closed, rather than asking the user for to attempt to log in again. Reprompting for user credentials is the typical behavior with other web servers (even IIS). This appears to be an artifact of setting the HTTP session, but other HTTP-login applications dont behave this way. We are having additional issues now because some users are saving that password, and its causing them account lockouts because the browsers do not realize they need to update saved credentials. Anyone know of a workaround? Wed rather not enable forms login if possible.

    Read the article

  • USB keyboard hit and miss as to whether it will work on boot-up

    - by user208745
    I am new to Ubuntu. Have installed 12.04 on a slave drive while I migrate. Usually booting into Ubuntu goes without a hitch but recently I often find I am unable to use the keyboard, and log-in using the on-screen KB. Sometimes if I remove the USB jack & re-connect it will start working again but not always. I do have an old PS/2 KB which I am using at the moment but.......has anyone any ideas on how to get the USB KB reliably connected? Thanks Dave

    Read the article

  • Windows virtual machince asks for a CD on boot

    - by poorni
    I have a Ubuntu Server 11.04 and I have created three virtual machines on separate PC with: Ubuntu Desktop Windows XP Windows 7 After completing the installation process, when I restart my server or for booting it for next time, Ubuntu desktop boots correctly but both the Windows OSes asks for a CD (that means any Windows OS variant CD), then it starts booting. Can any one resolve this problem?

    Read the article

  • Unreliable resume from suspend?

    - by dsimcha
    My desktop PC (home-built) resumes from suspend somewhat unreliably. I'd say that it resumes successfully about 85-90% of the time and hangs with a blank screen 5-10% of the time. As far as I can tell, the success or failure of the resume is completely random. I doubt it's a software problem because I triple boot Windows 7, Windows XP and Ubuntu and it's similar under all 3 operating systems. If it matters, my system is overclocked, though other than the resume-from-suspend issue, it's definitely rock stable. What are some of the obvious suspects that would cause random, sporadic failures to resume from suspend?

    Read the article

  • Kernel panic on boot up with 13.10 live-USB

    - by Muhammad Emad
    I am a new user for Ubuntu. I downloaded 13.10 yesterday and made a bootable USB with universal USB installer on my Lenovo IdeaPad Z580 laptop which is now using UEFI; everything appeared OK. When I booted from the LiveUSB I got the choices of trying or installing Ubuntu but both of them keep giving me these error: [ 1.929082] kernel panic-not syncing vfs unable to mount root fs on unknown-block (0.0) Please tell me what is going wrong?

    Read the article

  • dual boot ubuntu installation mishap

    - by user590849
    I have Windows 7 pc ,where i had 2 partitions, a c drive for my system files and a d drive for my data. I decided to install ubuntu 11.10 a couple of days ago and thought of install it in a separate partition of its own. So i made a separate Linux partition of 30GB. I downloaded ubuntu on my usb stick and installed. During the installation process i was asked where to install ubuntu so i opened up a screen that was similar to this one There were six partitions present ( I had made only 3 partition via windows). Their names were totally different from the ones that i had given in windows. So i selected a drive which had the same size as my Linux partition that i had made in windows ( no other partition had the same size). I clicked on install now and got an error message saying that "There was no root folder set". I set the newly made partition as my root folder and clicked install now. Now out of the 6 partitions that were created 3 were logical ( i had only created 3 partitions in windows). As soon as i clicked install now, the system asked me where i wanted to put my "swap space". I selected one of the logical drives and hit install. Ubuntu successfully installed on my system and at the end it asked me to reboot. I did and got the following error message: "missing operating system". I was shocked. I tried my windows recovery disk ( that i had gotten when i had purchased my laptop) and there i went into startup repair. In the startup repair option i was not able to locate windows. The system asked me to click the "Load drivers" button to load the drivers to my harddrive where windows was installed, but i could not locate any drivers to my harddrive. I tried this several times but to no success. I panicked and installed ubuntu, now this time click "ok" at every step( not worrying about the partition and all). The os installed correctly and i am now able to access my harddrive. NO data within the c drive is lost. All the windows system files are intact. I wish to recover my windows installation. How do i go about it? Thank you in advance. I do not want to format my computer and install windows again.

    Read the article

  • HP server delayed boot

    - by jjrab
    I'm currently using HP Proliant DL120 G5 servers running VMWare ESXi 4 to run server VM's. They are connecting to an iSCSI SAN for the shared storage. I'd like to implement a delayed boot of these hosts servers so that they don't boot up and try to connect to the SAN before the SAN is ready for connections after a power failure. Does anyone know of a good way to do this?

    Read the article

  • Problem accessing MICROSOFT##SSEE database (Error: 18456, Severity: 14, State: 16.)

    - by Philipp Schmid
    After an unexpected server shutdown due to a power failure, I can no longer connect to the internal windows database MICROSOFT##SSEE which is hosting Central Admin for my SBS 2008 server. The log shows: Error: 18456, Severity: 14, State: 16. Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. [CLIENT: <named pipe>] I've tried to connect using the SQL Management studio (connecting to .pipemssql$microsoft##sseesqlquery) but no luck. The SQL Server Configuration Manager doesn't show a entry for 'Protocols for MICROSOFT##SSEE' (but shows it for 2 other database hosted on the same SQL server 2005 Express edition. I have tried to restore the master.ldf and mastlog.log files from a backup, but the issue persists.

    Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >