Search Results

Search found 5845 results on 234 pages for 'commit protocol'.

Page 119/234 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126 | Next Page >

How to enable Jetty to support cometd/reverse ajax while let it listen to port 80?

- by janetsmith

Hi, I would like to use cometd / reverse ajax capability of Jetty 7. I tried to configure it so it listen to port 80, instead of 8080. However, according to http://jetty.mortbay.org/jetty5/faq/faq%5Fs%5F200-General%5Ft%5Fapache.html , Apache can be configured as a HTTP/1.1 proxy to pass selected request to the Jetty using the HTTP/1.1 protocol. This is simple to configure and use, but current versions of the apache mod_proxy do not support persistent connections. As far as I know, the reverse ajax in jetty is depending on continuation (I guess it is persistent connection). So how to let jetty support reverse ajax, while coexist with apache server? Thanks.

Read the article
Updating Cisco VPN config to add vpnc support

- by Igor Kuzmitshov

I have a Cisco 1841 configured for VPN connections of two types: Peer-to-peer for partners' routers (IPsec) — using different crypto isakmp key and crypto map with set peer, set transform-set, match address for every peer (same map name, different priorities). That crypto map name is added to the WAN interface. Client access (PPTP) — using vpdn-group with accept-dialin protocol pptp. Now, a new partner wants to connect using vpnc client. The latter needs IPSec ID (group name) and IPSec secret in addition to username and password. I guess that IPSec secret is pre-shared key that can be specified in crypto isakmp key on Cisco. But I could not find any VPN tutorials involving groups. Hence, my questions: How to add IPSec ID (group name) and IPSec secret on Cisco router for vpnc connections? Should I add a new crypto map matching all addresses as well? Is it possible to add this configuration without breaking the existing setup? Thank you.

Read the article
Gitweb showing opposite colors for added and removed text

- by Maddy

Hi, I have installed gitweb in our servers. And it started showing the branches and the commit diffs. But the syntax highlighting is opposite particularly for added and removed text. Supposed added text should be in green and removed text should be red. But I am seeing an opposite one. I can hack gitweb.css to get my job done. But felt like knowing why such issue is happening? And what might be the proper fix. (if any one knows good themes for gitweb? please mention)

Read the article
How can I limit the upload/download bandwidth on my CentOS server?

- by Dan Nestor

How can I limit the upload and download bandwidth on my CentOS server? This is a box with a single interface, eth0. Ideally, I would like a command-line solution (I've been trying to use tc), something that I could easily switch on and off in a script. So far I've been trying to do something like tc filter add dev eth0 protocol ip prio 50 u32 police rate 100kbit burst 10240 drop but I'm obviously missing a lot of knowledge and information. Can somebody help with a quick one-liner? Many thanks, Dan

Read the article
Difference between tcp recv buffer and tcp receive window size?

- by pradeepchhetri

The command shows the tcp receive buffer size in bytes. $ cat /proc/sys/net/ipv4/tcp_rmem 4096 87380 4001344 where the three values signifies the min, default and max values respectively. Then I tried to find the tcp window size using tcpdump command. $ sudo tcpdump -n -i eth0 'tcp[tcpflags] & (tcp-syn|tcp-ack) == tcp-syn and port 80 and host google.com' tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 16:15:41.465037 IP 172.16.31.141.51614 > 74.125.236.73.80: Flags [S], seq 3661804272, win 14600, options [mss 1460,sackOK,TS val 4452053 ecr 0,nop,wscale 6], length 0 I got the window size to be 14600 which is 10 times the size of MSS. Can anyone please tell me the relationship between the two.

Read the article
W2k8 RC1: Windows Media Servers (WMS) as proxy

- by da_didi

(fullquote from stackoverflow.com/questions/2690788/w2k8-rc1-windows-media-servers-wms-as-proxy/2690791#2690791) I will have one streaming-server (W2k8, unknown streaming protocol [rtsp, mss, http]) and half dozen streaming-servers as proxies to save bandwidth. I have read the documentation and installed the modules, but I am unsure how I have to configure the proxy's according to http://technet.microsoft.com/de-de/library/ee126142(en-us,WS.10).aspx - as a proxy or reverse proxy and how I minimize the bandwidth needs between origin server and proxy's. What is the best way to realize my setup? Any short how-tos? How can I announce all players to use the proxy? Route all rtsp/mms/http-requests through my proxy? Announce the proxy with DHCP-releases? Thanks!

Read the article
iptables rule to submit packets matching a specific negative rule

- by Aditya Sehgal

I am using netfilter_queue to pick up certain packets from the kernel and do some processing on them. To, the netfilter queue, I need all packets from a particular source except UDP packets with src port 2152 & dst port 2152. I try to add the iptable rule as iptables -A OUTPUT ! s 192.168.0.3 ! -p udp ! --sport 2905 ! --dport 2905 -j NFQUEUE --queue-num 0 iptables throw up an error of Invalid Argument. Querying dmesg, I see the following error print ip_tables: udp match: only valid for protocol 17 I have tried the following variation with the same error thrown. iptables -A OUTPUT ! s 192.168.0.3 ! -p udp --sport 2905 --dport 2905 -j NFQUEUE --queue-num 0 Can you please advise on the correct usage of the iptables command for my case.

Read the article
Mantaining Wordpress website with subversion

- by Geries

I want to setup a website using wordpress, which we can modified locally and then via subversion commit the site and make it public. This means to installing new plugins, changing the content, testing updates of wordpress to see if they work with the theme, etc. The idea is to control the development on the site, in case we need to keep track of the dev or roll back, because of unexpected bugs in a the plugins, theme, etc. I've read this article in codex, however I'm not sure how this is done when, we want to include the content and changes on the options of worpdress and plugins (which is in the mysql). Thanks

Read the article
Transfer files using ssh

- by zozo

Good day to all. I am using ssh (winSCP) to transfer some files from a server to my workstation. The problem is that at some files I get disconnected. Always same files. I am the owner of the directory so I guess the file permissions is not a problem. (Also I set the permissions to 777). Is there a size limit or something like that? Thank you for your time. Protocol is SFTP, server is 32bit machine. Files are 100MB tops. Added: Worked with filezilla using ftp. This temporarily fix the problem but is not exactly a solution since maybe next time I won't have root access to create a ftp account

Read the article
How to supply parameters in URI schema?

- by abhishekgarg

I just started working with URI schema and successfully created one in Windows and Linux as well, but I am not able to parse any parameters to it. In Linux I am trying to open a file "test.py" in gedit, so for schema part I used these commands: gconftool -2 -t string /desktop/gnome/url-handlers/geditapp/command "gedit %s" gconftool -2 -t bool/desktop/gnome/url-handlers/geditapp/enabled true This is creating the URI protocol and I'm able to open the application with the Web-browser, but its not taking the parameters for the file I want to open, so I'm using the following command: <a href="geditapp:/opt/test/myfile.py">open</a> Which opens the gedit but without the file. Can someone please help me with this?

Read the article
2 x Netgear GS724T (Dual GBIC) trunking issue

- by Arthor

I have the following: Netgear GS724T (Firmware Version V1.0.3_35, Protocol Version - 2.001.002) 4 x Indineon ISFP GBR/FC Settings STP Function - Enabled Fast Link - Enabled Trunking port 23,24, (21,22 - RJ45 cables, but not connected.) I have connected both switches via 2 fiber cables and want to use trunking. The problem I am having. Sometimes I get a an issue when none of the switches cannot talk with each other, nor the devices, sometime they can. The problem is irregular and no patten can be determined The statistics shows that when the switches does not work, they have RX errors If I remove one to the GBIC connections, then everything works as normal.] Question Does anyone have a solution for this please? Thanks

Read the article
Allow HTTPS cookies but not HTTP?

- by Ken

I want to allow cookies for a domain but only over HTTPS -- not cookies from the same domain that come from HTTP. For example, I don't want any http://www.google.com cookies, but I do want to allow https://www.google.com cookies (because Calendars are there). Is there a way to do this? Does the goal even make sense? In Chrome, it only allows domain names, not URLs, to be added to the cookie exception list. In Firefox, it allows a protocol, but it only records the domain name, and if you click "Allow" or "Deny", it changes the same entry in the list.

Read the article
MySql service stops under 2008 r2 x64

- by volody

I have installed MySql 5.5 server under windows 2008r2 x64 Apparently I can see that MySql service stops even if is configured to start automatically What can I do to find out why this is happening? MySql database is used as backend of ASP.Net web site Is it possible that web site was not active for a while and system stop mysql service? Update: It was mysql-5.5.7-rc-winx64. I could be an issue with this version (release candidate). Now I am trying to install mysql-5.5.8-winx64 And I have an issue with configuring MySql to work using name pipes I did uncheck use of TCP/IP protocol and configuration wizard just hangs Update: I have found workaround. It is required to configure MySql to use TCP/IP first, then reconfigure to use named pipes It looks like this link also has some information about the possible problems How should I diagnose ERROR 1045 during MySQL installation?

Read the article
IPTables masquerading with one NIC

- by Tuinslak

Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

Read the article
Suppress EXT3-fs warning on mount

- by STM

I am familiar with output suppress on Unix machines, ie: cat /file/that/doesnt/exist > /dev/null 2>& However I can't seem to suppress the output of mount when an ext3 filesystem is mounted for the nth time, and it recommends an fsck. As it happens, fscks are run regularly by another machine, so these warning messages are needlessly interrupting the flow of output to my pretty bash script. These are the errors: # mount -t ext3 /dev/sda1 /mnt > /dev/null 2>& kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. Can anyone shed some light on this? I'm clearly blocking both fd's, but somehow output is still getting through. This is GNU Bash v2.05a

Read the article
What is Light Peak

- by Jonathan.

I've heard this a lot recently, todo with Apple and Intel. Some says it's a protocol, others say it's fibre optic, and others say it's copper. One source even said it was a "wireless wire". Apparently it can carry data, but not video streams, surely the cable can't know the difference between 1s and 0s representing data, and 1s and 0s representing video streams. Or it will replace all the wires we currently have except power, another place said it is for inside laptops. Those are just examples so I haven't given any sources, I just want to know what on Earth Light Peak is?

Read the article
TFS2010 - Correctly setting up Host Header

- by Keith Barrows

We have a TFS2010 install on a Win2008R2 Server running IIS7. I've created a host header for TFS and want to use that instead of machineName:8080. I am getting weird behavior from it now. Every other time I log in I get: TF31002: Unable to connect to this Team Foundation Server: http://web2/tfs. Team Foundation Server Url: http://web2/tfs. Possible reasons for failure include: - The name, port number, or protocol for the Team Foundation Server is incorrect. - The Team Foundation Server is offline. - The password has expired or is incorrect. Technical information (for administrator): The request failed with HTTP status 404: Not Found. I force a reconnect and voila - there it is. Also, connecting to the web site rarely works but connecting via VS2010 works 50% of the time. What do i need to change to stabilize this?

Read the article
Automatizing the backup of my databases and files with cron

- by Patrick

hi, I want to automatize the backup of my databases and files with cron. Should I add the following lines to crontab ? mysqldump -u root -pPASSWORD database_name | gzip > /home/backup/database_`date +\%m-\%d-\%Y`.sql.gz svn commit -m "Committing the working copy containing the database dump" 1) First of all, is this a good approach ? 2) It is not clear how to specify the repository and the working copy with svn" 3) How can I run svn only when the mysqldump is done and not before ? Avoiding conflicts Any other tip ? thanks

Read the article
AS2 Server Software Costs

- by CandyCo

We're currently using Cleo LexiCom as our server software for receiving EDI transmissions via the AS2 protocol. We have 7 trading partners per year, and this runs us about $800/year for support from Cleo. We need to expand from 7 trading partners to 10 or so, and Cleo charges roughly $600 per new host, plus an expanded yearly support fee. My question(s) are: Does anyone know of a cheaper developer of AS2 server software, and perhaps one that doesn't charge per new host? Does anyone have any clue why we are being charged an upfront fee for new hosts, and if this is a standard practice for AS2 software providers? It seems really odd that we are required to pay upfront costs for this. I could completely understand an increase in the yearly support, however.

Read the article
traffic shaping for certain (local) users

- by JMW

Hello, i'm using ubuntu 10.10 i've a local backup user called "backup". :) i would like to give this user just a bandwidth of 1Mbit. No matter which software wants to connect to the network. this solution doesn't work: iptables -t mangle -A OUTPUT -p tcp -m owner --uid-owner 1001 -j MARK --set-mark 12 iptables -t mangle -A POSTROUTING -p tcp -m owner --uid-owner 1001 -j MARK --set-mark 12 tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 2 htb default 1 tc filter add dev eth0 parent 2: protocol ip pref 2 handle 50 fw classid 2:6 tc class add dev eth0 parent 2: classid 2:6 htb rate 10Kbit ceil 1Mbit tc qdisc show dev eth0 tc class show dev eth0 tc filter show dev eth0 does anyone know how to do it? thanks a lot in advance

Read the article
GDM login screen is not displayed with VNC

- by niboshi

Hi, I set up VNC server with xinetd. Also configured GDM so that XDMCP is enabled. VNC connection seems okay, but GDM login screen is not shown. Instead I can only see old bare X screen (gray meshed background and X-shaped mouse pointer), which I can't do any interaction with it. What can I do to fix the problem? No log is written below /var/log/. Server distribution: Ubuntu marverick /etc/xinetd.d/vnc is like below: service vnc1024 { disable = no socket_type = stream protocol = tcp wait = no user = nobody server = /usr/bin/Xvnc server_args = -inetd -query localhost -geometry 1024x768 -depth 24 -once securitytypes=none port = 12345 } /etc/gdm/custom.conf: [daemon] [security] DisallowTCP=false [xdmcp] Enable=true [gui] [greeter] [chooser] [debug] [servers] /etc/services is also configured. Thanks

Read the article
Monit can't detect MySQL, but I can

- by Matchu

Monit is configured to watch MySQL on localhost at port 3306. check process mysqld with pidfile /var/lib/mysql/li175-241.pid start program = "/etc/init.d/mysql start" stop program = "/etc/init.d/mysql stop" if failed port 3306 protocol mysql then restart if 5 restarts within 5 cycles then timeout My application, which is configured to connect to MySQL via localhost:3306, is running just fine and can access the database. I can even use MySQL Query Browser to connect to the database remotely via port 3306. The port is totally open and possible to connect to. Therefore, I'm pretty darn certain that it's running. However, running monit -v reveals that Monit cannot detect MySQL on that port. 'mysqld' failed, cannot open a connection to INET[localhost:3306] via TCP This happens consistently, until Monit decides not to track MySQL anymore, as configured. How can I begin to troubleshoot this issue?

Read the article
Netboot Intel Macs without BSDP

- by notpeter

I have a netboot setup with DeployStudio that works great in my lab, but doesn't work on our main network. After some digging, I believe it's because our network admins are filtering BSDP (Boot Service Discovery Protocol) on our subnet at the switch level. Is it possible to hard code which server my clients (early 2007 iMac Core2Duos) should boot from without relying on BSDP? Perhaps relevant details: I do not have control over switch configs or DHCP settings. Client and server are running 10.6 Snow Leopard. The clients see the netboot server advertising itself in the 'Startup Disk' system preferences pane, but when I go to netboot it just leaves me with a flashing globe.

Read the article
Automatically updating routing table on server

- by bramp

I have a LAN with three routers on it, one connected to the Internet, one VPN router connected to a few remote sites, and a final route connected to a private network (using BGP to get prefix advertisements). On the same LAN I have multiple Linux servers which needs access to the networks behind each router. I have achieved this by configuring static routes on the server, pointing the different network prefixes to the correct router. This has worked well, but every time we connect to a new remote VPN, we have to change all the servers to be aware that the network is now accessible via the VPN, and not via the default Internet route. What I want is a way to automatically update the routes on all of the servers, when the route is added to a routers. Now, I could install Quagga or something similar on all the servers to receive router advertisements, but that seems like overkill. So my question is what is the easiest/simpliest way to update the routing tables on the server automatically, and what protocol is best suited for this purpose. thanks

Read the article
Debian wheezy keyboard shortcut for both opening and closing a terminal

- by Peter

I recently installed tilda and I would like to open it and close with the same keyboard shortcut. I wrote little something in bash that closes tilda if it is open and opens tilda when there is no such a process in ps -ef. It looks like this: a=ps -ef | fgrep -i tilda | cut -d' ' -f4 | head -1;if [ $a ] ; then kill $a; else tilda; fi It seems to be working (at least partially) when I commit this in terminal, but when I assign this command to specific keyboard shortcut (for example alt+1) it does nothing. Any suggestions? btw. is it possible to assign this shortcut for button '`' like in Quake?

Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126 | Next Page >