Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 123/315 | < Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >

  • Vaio Laptop wireless connectivity loss after some minute

    - by Mehran Meidani
    I have a big problem with my laptop, My laptop loss it's connectivity to internet randomly! for Example sometimes it's ok up to 1h but usually the problem occurred after 5 min. When I run these command, i can continue working with internet : ipconfig /release ipconfig /renew If i turn wireless off and on, the problem don't solved I have another laptop (Macbook pro) and it doesn't have any problem I use Linksys E2000 as an wireless access point Model : Sony vaio sa21gx OS : Windows 7 SP1 Thank you for your help and sorry for my bad english :)

    Read the article

  • Network problems with Ubuntu on VMware

    - by svick
    I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

    Read the article

  • Troubleshoot dropped wireless connections

    - by Jack
    I was recently hired in the IT department of a small company (~180 users) and one of the issues that people have been complaining about is having their wi-fi connections drop during meetings. The company is using an HP ProCurve Wireless LAN with 10 APs and a controller unit located in the server room. I don't have any experience troubleshooting WLAN in a multi-AP environment, so I'm trying to at least gather information using free or cheap tools. I did a basic site survey using the free version of Ekahau HeatMapper and discovered the following in one of the conference rooms that has been a problem. The program picked up three access points (plus a bunch of others with much lower signals that were out of range): AP 1: SSID: "Unknown SSID" - Signal strength: -48 dBm - -40 dBm. Channel: 2 AP 2: SSID "CompanyMain" - Signal strength: -35 dBm or greater. Channel: 2. Security: WEP (This is the main SSID for the company's WLAN.) AP 3: SSID: "CompanyGuest" - Signal strength: -40 dBm - -35 dBm. Channel: 2. Security: WPA2 (This SSID is the company's "guest" WLAN, which was setup to allow Internet access, but prevent network access.) Is there anything that you see that is clearly a problem from the above? I'm assuming that the unknown SSID might be a big problem, and that it is an AP from a neighboring office that is causing interference. Does that seem likely? Also, regarding channel, should we try changing the channels of our APs to avoid interference with that unknown SSID? (Since everything seems to be on Channel 2?) Should our APs be on different channels? In other words, should the CompanyMain and CompanyGuest APs be on different channels? Finally, any recommendations for free/cheap tools to help me figure this out, and/or a good methodology to follow? Thanks in advance for any help. Jack

    Read the article

  • Windows Hosted Network Redirect to IIS

    - by rulestein
    I would like to setup a Windows 7 machine as a wifi hotspot that always redirects to the IIS web hosting on the same machine. I have the hotspot piece working with the built in hosted network of Widnows 7. The webhosting was easy enough with IIS. Now, how do I connect the 2? The idea is to have a standalone device that users will be able to connect to the wifi and any webpage they go to will redirect to the internal webpage. I only expect 1 or 2 users at a time and there won't be any internet access involved.

    Read the article

  • Wireless disconnects at random after upgrade to Ubuntu 10.4

    - by Daniel Elessedil Kjeserud
    After upgrading my home server from Ubuntu 8.10 to 10.4 my wireless seemingly drops out, even though my IRC client keeps it's connection to the servers, so it looks like the machine just stops taking wireless requests. A ping will give a me this Request timeout for icmp_seq 27 ping: sendto: Host is down After a while the machine just starts responding again, without any interaction from me. When the machine comes back, this is what dmesg gives me [ 18.296288] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.296350] wlan0: deauthenticating from 00:1b:63:22:a4:5f by local choice (reason=3) [ 18.296440] wlan0: direct probe to AP 00:1b:63:22:a4:5f (try 1) [ 18.298697] wlan0: direct probe responded [ 18.298706] wlan0: authenticate with AP 00:1b:63:22:a4:5f (try 1) [ 18.306836] wlan0: authenticated [ 18.306886] wlan0: associate with AP 00:1b:63:22:a4:5f (try 1) [ 18.309396] wlan0: RX AssocResp from 00:1b:63:22:a4:5f (capab=0x411 status=0 aid=2) [ 18.309402] wlan0: associated [ 18.310187] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 18.447742] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) [ 18.447748] apm: overridden by ACPI. [ 19.163282] padlock: VIA PadLock not detected. [ 28.352022] wlan0: no IPv6 routers present kjes@brin:~$ lspci 02:07.0 Network controller: RaLink RT2561/RT61 rev B 802.11g It's on a wireless network with WPA2, the machine worked without any problems on the same wireless network since Ubuntu 8.10 was the most resent version, and there have been no changes to my network recently. Even though the server drops out, everything else on the network keeps working like normal.

    Read the article

  • apache2 slow responding (debian)

    - by baloo
    I'm running an apache2 2.2.9 webserver with modpython and mpm_worker_module. The current config for the mpm is ServerLimit 32 StartServers 10 MaxClients 800 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 The server has 1G of ram and a 100Mbit connection. Checking netstat -na | grep ESTABLISHED | wc -l gives me a number between 50 - 60. The load is about 1.0 Every pageload is also cached by memcached. I can't see why the server is so slow in responding to new connections, sometimes droping them completely? Also tried disabling iptables to make sure it's not because of a full state table or something like that. The only thing in dmesg is a lot of spam about "TCP: Treason uncloaked!"

    Read the article

  • Suddenly blocked from a site

    - by Diego Romero
    Suddenly from a time to now I haven't been able to go to a site I used to go frequently for maintenance (Wordpress). I tried different browsers, restarting my laptop, clearing cache, history, cookies. Also did a ping to the site ip, go 4 packets send and 4 lost. This is a problem I think with only my laptop, since I've been able to go into the site from other devices in the same network. I have also tried connecting to the same site from a completely different network with the same problem. I really don't know what to do about this, any advices? PS: site hosted in wp engine if that has anything to do with this problem.

    Read the article

  • pptpd configuration

    - by Ian R.
    I would like a little help on configuring pptp so I can use my server as a vpn server since I have 10 ip's on it and I travel a lot so that would really help me and my partners. I managed to install everything needed but my vpn client fails to connect due to some reason that I cannot understand. I know there are 2 files in pptp that you're supposed to edit so I will post my 2 files here: /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 proxyarp nodefaultroute lock nobsdcomp /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip xx.158.177.231 remoteip xx.158.177.103,xx.158.177.116,xx.158.177.121,xx.158.177.124,xx.158.177.125,xx.158.177.131,xx.158.177.134,xx.158.177.139,xx.158.177.142,xx.158.177.145 interfaces file eth0 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.231 Bcast:xx.158.177.255 Mask:255.255.254.0 inet6 addr: xx80::216:3eff:fe51:31ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56352 errors:0 dropped:0 overruns:0 frame:0 TX packets:3xx15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4884030 (4.8 MB) TX bytes:6780974 (6.7 MB) Interrupt:16 eth0:1 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.103 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:2 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.116 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:3 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.121 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:4 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.124 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:5 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.125 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:6 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.131 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:7 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.134 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:8 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.139 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:9 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.142 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:10 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.145 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:286 (286.0 B) TX bytes:286 (286.0 B)

    Read the article

  • Why does changing the physical socket on your router cause delays?

    - by Josh Browning
    My question involves the delays involved with changing which physical socket your ethernet cable is connected to. I am aware that if you are connected to a router on a network and then change which physical socket on that router you are using you will gain very small additional delays initially. However I am curious as to what causes these delays. I originally thought it was to do with the infromation stored in the routing table and whether that was allocated to a specific socket on the router or not. Although, if your IP address is the same then I don't understand why there would be delays because I would of assumed that any information within the router was linked to an IP address rather than a physical socket.

    Read the article

  • Set 802.1Q tagged port on VLAN1 on Dell PowerConnect switch

    - by Javier
    I'm having big troubles when adding this Dell switch to my network. Here we use several VLANs to segment traffic. All switches (3com and DLink mostly) have configured the same VLANs, most ports are 'untagged' and belong to a single VLAN, except for the ports used to join together the switches (in a star topology), these ports belong to all VLANs and use 802.1Q tags. So far, it works really well. But on this new switch (a Dell PowerConnect 5448), the settings are very different (and confusing). I have configured the same VLANs, an the uplink ports are set in 'general' mode (supposed to be fully 802.1Q compliant), I can set the VLAN membership as 'T' on these ports for all VLANs except VLAN 1. It always stay as 'U' on VLAN 1. Any ideas?

    Read the article

  • Using multiple wifi connections simultaneously on Windows

    - by Salman A
    My office PC has a one wireless network card and there are three available wifi connections: primary, backup and backup of a backup (grin). Is it possible for me to use all three simultaneously. If this results in an increase in bandwidth that's well and good, but primary reason is every now and then one of the network fails and i have to switch back and forth between the available networks by disconnecting, viewing available networks and connecting to next one hoping its running. Do i need more than one network card or a software e.g. a proxy.

    Read the article

  • Using multiple wifi connections simultaneously on Windows

    - by Salman A
    My office PC has a one wireless network card and there are three available wifi connections: primary, backup and backup of a backup (grin). Is it possible for me to use all three simultaneously. If this results in an increase in bandwidth that's well and good, but primary reason is every now and then one of the network fails and i have to switch back and forth between the available networks by disconnecting, viewing available networks and connecting to next one hoping its running. Do i need more than one network card or a software e.g. a proxy.

    Read the article

  • Wireless Network Connection gets dropped at times under Windows 7

    - by n179911
    I have running Windows 7 on my hp laptop with 802.11n wifi adapter. Some times, I lost wireless internet connection. Under the 'Wireless Connection' when I click the notification area, it said 'my home network is 'connected'... But in the header 'currently Connected to' it said 'no internet access' instead of 'internet access' I can 'fix' my problem by going to the 'wireless connection' my home network, click 'disconnect' and then click 'connect'. And when it comes back up, it gets connected again. any idea how can i fix this problem? Thank you.

    Read the article

  • Downstream to server periodically dropping and spiking

    - by dauphic
    I have a server located in Canada. I'm experiencing that, when connecting from the south-eastern US (southern California, Arizona), I see my downstream on connections to this server periodically drop to 0 for 1-3 seconds, then spike in the next second and receive all of the data that should have been received during the drop off period. This doesn't happen in regular intervals, but it does happen often, usually once every 5-10 seconds. I've gotten trace routes from users with various ISPs and locations, but I'm not seeing any spikes or drop offs in response times, or any sort of packet loss. I'm guessing this is because ICMP is prioritized, though. It seems like a misbehaving router along the way, but I have no idea how to figure out where the problem lies (let alone if there's any way to work around it). Is there any way for me to diagnose this problem?

    Read the article

  • Ping server NETBIOS name returns wrong IP and "Destination host unreachable"

    - by music2myear
    Problem server is Windows 2008 R2 VM running on VMWare ESXi 4 host. Single network adapter manually assigned single IP address (192.168.1.11). When I ping the server from any other network computer, it returns 192.168.1.124 and "Destination host unreachable". Yesterday I found a second network adapter assigned to this server with an IP of 169.254... indicating it had no real valid IP. Using the MAC addresses I determined which adapter was not needed/not wanted, and removed it using VMWare systems. This is the network Printer Server and, understandably, nothing is printing right now. I've looked at the solutions here Why was my ping answered by a different IP address than the one pinged? and they aren't applicable to my situation for the following reasons: Output of arp -a on another computer returns the correct IP address (.1.11) assigned to the correct MAC address, the incorrect IP .1.124 is not listed, and the MAC of the network adapter I removed yesterday is not listed at all. I checked out the Microsoft KB article which listed pretty much my exact symptoms ( http://support.microsoft.com/kb/981953 ) and it says to check binding orders and look for hidden adapters. But there are no hidden adapters, and there is only one Network Adapter listed in the Binding Order list. Essentially, I can communicate from the server TO any other network device, but I cannot communicate from any other network device TO the server. Help! UPDATE: Solution found, see this solution for the details.

    Read the article

  • WIFI: iPhone/iPad getting much slower bandwidth than laptop

    - by Sam
    I just got cable internet installed (Comcast). It claims that my down speed should be 25mbit. Over wifi, I get close to that on my laptop, but only about 8 on average with my iPhone/iPad. I'm using testmy.net in the browser on all devices. I have an ARRIS / Motorola SurfBoard SB6141 DOCSIS 3.0 Cable Modem and a Medialink Wireless N Broadband Router. I read somewhere that disabling WMM and the firewall on the router would help (is this even a safe idea?). I've tried both, and neither seem to make much of a difference, if any at all (sidebar: I've noticed that my download speeds vary wildly with cable internet... on my laptop, I'll get 12 down, then 22 five minutes later. Is this typical for cable internet?).

    Read the article

  • network topology including many services

    - by mete
    I know this is yet another question on how to setup network but I hope you are not bored of such questions yet. The site is also an office, so it includes windows dc, windows ad, exchange, sql, file sharing, development app servers and other pcs. In addition to office (internal) things, there are both test and prod environments consisting of a web server-app server-sql stack. There is also ftp service open to public. I consider: dmz1 - web server - exchange edge - ftp dmz2 - app server - sql for app server internal - dc and ad - exchange hub and transport - internal file sharing - sql for internal use - app servers for internal use - pcs public - dmz1, only web, ftp and smtp public - dmz2 not possible public - internal not possible dmz1 - dmz2 is possible from web servers to app servers by using http or ajp dmz1 - internal is only possible for exchange, otherwise not possible dmz2 - internal not possible Does this sound ok ? Any other recommendations ? It will be configured using either MS ISA or Jupiter SSG. Thank you.

    Read the article

  • mail server administration

    - by kibs
    MY postfix does not show that it is listening to the smtp daemon getting mesaage below: The message WAS NOT relayed Reporting-MTA: dns; mail.mak.ac.ug Received-From-MTA: smtp; mail.mak.ac.ug ([127.0.0.1]) Arrival-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Original-Recipient: rfc822;[email protected] Final-Recipient: rfc822;[email protected] Action: failed Status: 5.4.0 Remote-MTA: dns; 127.0.0.1 Diagnostic-Code: smtp; 554 5.4.0 Error: too many hops Last-Attempt-Date: Wed, 19 May 2010 12:45:20 +0300 (EAT) Final-Log-ID: 23434-08/A38QHg8z+0r7 undeliverable mail MTA BLOCKED OUTPUT FROM lsof -i tcp:25 command master 3014 root 12u IPv4 9429 TCP *:smtp (LISTEN) (Postfix as a user is missing )

    Read the article

  • how to broadcast a PXE server like Trinity Rescue Kit

    - by Larry G. Wapnitsky
    I would like to set up a portable PXE server for diagnostic purposes. The issue is that I won't always have access to the DHCP server, or the router itself (sometimes a home router) doesn't have an easily accessible place to set the servername/file for broadcast. I know that Trinity Rescue Kit is able to broadcast its PXE server without its own DHCP server. Can anyone point me in the direction to set this up on my own (without Trinity)? Thanks.

    Read the article

  • open source solution to a gateway for a network of a housing cooperative of 150 people

    - by SirDinosaur
    i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

    Read the article

  • collectd:Monitoring server not showing clients

    - by Quintin Par
    I have setup a monitoring server with the following setup. <Plugin network> Listen "0.0.0.0" "25826" </Plugin> Now my clients are sending data to the monitoring server(verified through tcpdump). Even the collection folder shows that the data is being dumped /var/lib/collectd/rrd [ec2-user at x rrd]$ ll total 4 drwxr-xr-x 11 root root 4096 Nov 20 17:53 x-web-1.y.com [ec2-user at x rrd]$ I have also verified with find . -mmin 1 to see if its being constantly updated. [ec2-user@x rrd]$ find . -mmin 1 ./x-web-1.y.com/interface-eth0/if_errors.rrd ./x-web-1.y.com/interface-eth0/if_packets.rrd ./x-web-1.y.com/interface-eth0/if_octets.rrd ./x-web-1.y.com/disk-xvda1/disk_time.rrd ./x-web-1.y.com/disk-xvda1/disk_ops.rrd ./x-web-1.y.com/disk-xvda1/disk_octets.rrd ./x-web-1.y.com/disk-xvda1/disk_merged.rrd But when i look it up through collectd-web, I don't see the clients What might be wrong in my setup?

    Read the article

  • Ruckus wireless AP and Dell PowerConnect configuration problems

    - by DanielJay
    We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

    Read the article

< Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >