Search Results

Search found 86974 results on 3479 pages for 'visualsvn server'.

Page 1239/3479 | < Previous Page | 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246  | Next Page >

• Unable to access Windows share

  - by mbnoimi

  I've installed Alfresco 4.2.d under Ubuntu 12.04 LTS; Everything done fine except I can't access it from Windows share although I got the link from Alfresco explorer which is: file:///%5C%5CECSA%5CAlfresco%5CSites%5Cswsdp%5CdocumentLibrary%5CAgency%20Files%5CImages%5Ccoins.JPG I tried to access it from: \\ECSA but I failed too so I made a ping (192.168.0.70 is server IP) then I got: C:\Users\user>ping 192.168.0.70 Pinging 192.168.0.70 with 32 bytes of data: Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Reply from 192.168.0.70: bytes=32 time<1ms TTL=64 Ping statistics for 192.168.0.70: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\Users\user>ping ECSA Ping request could not find host ECSA. Please check the name and try C:\Users\user> Some logs of what's going on: C:\Users\user>net view ECSA System error 1707 has occurred. The network address is invalid. C:\Users\user>nbtstat -a 192.168.0.70 Local Area Connection: Node IpAddress: [192.168.0.84] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- ECSA <20> UNIQUE Registered ECSA <00> UNIQUE Registered WORKGROUP <00> GROUP Registered MAC Address = 00-00-00-00-00-00 C:\Users\user> CIFS Server Configuration in file-servers.properties ### CIFS Server Configuration - file-servers.properties ### cifs.enabled=true cifs.serverName=${localname}A cifs.domain= cifs.broadcast=255.255.255.255 cifs.bindto=192.168.0.70 cifs.ipv6.enabled=false cifs.hostannounce=true cifs.disableNIO=false cifs.disableNativeCode=false cifs.sessionTimeout=900 cifs.maximumVirtualCircuitsPerSession=16 cifs.tcpipSMB.port=445 cifs.netBIOSSMB.sessionPort=139 cifs.netBIOSSMB.namePort=137 cifs.netBIOSSMB.datagramPort=138 cifs.WINS.autoDetectEnabled=true cifs.WINS.primary=192.168.0.70 cifs.WINS.secondary=192.168.0.1 cifs.sessionDebug= cifs.pseudoFiles.enabled=true cifs.pseudoFiles.explorerURL.enabled=true cifs.pseudoFiles.explorerURL.fileName=__Alfresco.url cifs.pseudoFiles.shareURL.enabled=false cifs.pseudoFiles.shareURL.fileName=__Share.url How can I fix this issue?

  Read the article

• Two hosting providers running simultaneously... possible / not possible? good practice / unnecessary?

  - by user29600

  For the sake of their reputation, I won't mention the names. But I'll just use: Business I worked for previously - ABC Web Dev Hosting company they used - XYZ Hosting I recently found out that XYZ Hosting had some sort of incident where they ended up losing a lot of their client's data - including ABC Web Dev's. ABC Web Dev was able to recover some of their customer's websites, after pulling them from their local development computers and putting them up on another hosting provider. They ended up losing a lot of clients because of it and their reputation ruined. I'm starting my own web dev company and I don't want to run into this same issue. I'm planning on using Rackspace but, although they are a great company, according to wikipedia they still have had downtime in their past. I thought it might be a good idea to try to run two providers at once, to ensure that if anything happened in one the websites would still be live because of the other. I know the websites would have to be pulling from one server at all times, but if there's a way to redirect requests to the second server if the first one is down that would solve my issue. As a note, we will have a staging environment setup locally which will allow for quick recovery if a provider did have any issues, however I'd like to avoid any downtime at all if possible. So my questions are: Has anyone tried running two providers simultaneously? Would this be considered good practice or am I going too far? Is there really any way to run two simultaneously where one server acts as a backup?

  Read the article

• Openfiler iSCSI performance

  - by Justin

  Hoping someone can point me in the right direction with some iSCSI performance issues I'm having. I'm running Openfiler 2.99 on an older ProLiant DL360 G5. Dual Xeon processor, 6GB ECC RAM, Intel Gigabit Server NIC, SAS controller with and 3 10K SAS drives in a RAID 5. When I run a simple write test from the box directly the performance is very good: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 4.64468 s, 226 MB/s So I created a LUN, attached it to another box I have running ESXi 5.1 (Core i7 2600k, 16GB RAM, Intel Gigabit Server NIC) and created a new datastore. Once I created the datastore I was able to create and start a VM running CentOS with 2GB of RAM and 16GB of disk space. The OS installed fine and I'm able to use it but when I ran the same test inside the VM I get dramatically different results: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 26.8786 s, 39.0 MB/s [root@localhost ~]# Both servers have brand new Intel Server NIC's and I have Jumbo Frames enabled on the switch, the openfiler box as well as the VMKernel adapter on the ESXi box. I can confirm this is set up properly by using the vmkping command from the ESXi host: ~ # vmkping 10.0.0.1 -s 9000 PING 10.0.0.1 (10.0.0.1): 9000 data bytes 9008 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.533 ms 9008 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.736 ms 9008 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.570 ms The only thing I haven't tried as far as networking goes is bonding two interfaces together. I'm open to trying that down the road but for now I am trying to keep things simple. I know this is a pretty modest setup and I'm not expecting top notch performance but I would like to see 90-100MB/s. Any ideas?

  Read the article

• How can I automatically restart Apache and Varnish if can't fetch a file?

  - by Tyler

  I need to restart Apache and Varnish and email some logs when the script can't fetch robots.txt but I am getting an error ./healthcheck: 43 [[: not found My server is Ubuntu 12.04 64-bit #!/bin/sh # Check if can fetch robots.txt if not then restart Apache and Varnish # Send last few lines of logs with date via email PATH=/bin:/usr/bin THEDIR=/tmp/web-server-health [email protected] mkdir -p $THEDIR if ( wget --timeout=30 -q -P $THEDIR http://website.com/robots.txt ) then # we are up touch ~/.apache-was-up else # down! but if it was down already, don't keep spamming if [[ -f ~/.apache-was-up ]] then # write a nice e-mail echo -n "Web server down at " > $THEDIR/mail date >> $THEDIR/mail echo >> $THEDIR/mail echo "Apache Log:" >> $THEDIR/mail tail -n 30 /var/log/apache2/error.log >> $THEDIR/mail echo >> $THEDIR/mail echo "AUTH Log:" >> $THEDIR/mail tail -n 30 /var/log/auth.log >> $THEDIR/mail echo >> $THEDIR/mail # kick apache echo "Now kicking apache..." >> $THEDIR/mail /etc/init.d/varnish stop >> $THEDIR/mail 2>&1 killall -9 varnishd >> $THEDIR/mail 2>&1 /etc/init.d/varnish start >> $THEDIR/mail 2>&1 /etc/init.d/apache2 stop >> $THEDIR/mail 2>&1 killall -9 apache2 >> $THEDIR/mail 2>&1 /etc/init.d/apache2 start >> $THEDIR/mail 2>&1 # prepare the mail echo >> $THEDIR/mail echo "Good luck troubleshooting!" >> $THEDIR/mail # send the mail sendemail -o message-content-type=html -f [email protected] -t $EMAIL -u ALARM -m < $THEDIR/mail rm ~/.apache-was-up fi fi rm -rf $THEDIR

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast (Corvallis, OR) to the east coast (NY, NY). However, I am seeing some disturbing latency numbers from my location (Berkeley, CA) to the NYC host. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: Berkeley to NYC server: 215 ms latency, 46ms transfer time, 261ms total Berkeley to Corvallis server: 114ms latency, 41ms transfer time, 155ms total some URLs if you want to try yourself: http://careers.stackoverflow.com/content/cso/img/logo.png (NY, NY) http://serverfault.com/cache/logo.png (Corvallis, OR) It makes sense that Corvallis, OR is geographically closer to Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only went up 10%, yet the latency went up ten times as much! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... http://serverfault.com/questions/63531/does-routing-distance-affect-performance-significantly http://serverfault.com/questions/61719/how-does-geography-affect-network-latency http://serverfault.com/questions/6210/latency-in-internet-connections-from-europe-to-usa ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• Can't get SSH public key authentication to work

  - by Trey Parkman

  My server is running CentOS 5.3. I'm on a Mac running Leopard. I don't know which is responsible for this: I can log on to my server just fine via password authentication. I've gone through all of the steps for setting up PKA (as described at http://www.centos.org/docs/5/html/Deployment_Guide-en-US/s1-ssh-beyondshell.html), but when I use SSH, it refuses to even attempt publickey verification. Using the command ssh -vvv user@host (where -vvv cranks up verbosity to the maximum level) I get the following relevant output: debug2: key: /Users/me/.ssh/id_dsa (0x123456) debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug3: start over, passed a different list publickey,gssapi-with-mic,password debug3: preferred keyboard-interactive,password debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password followed by a prompt for my password. If I try to force the issue with ssh -vvv -o PreferredAuthentications=publickey user@host I get debug2: key: /Users/me/.ssh/id_dsa (0x123456) debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug3: start over, passed a different list publickey,gssapi-with-mic,password debug3: preferred publickey debug3: authmethod_lookup publickey debug3: No more authentication methods to try. So, even though the server says it accepts the publickey authentication method, and my SSH client insists on it, I'm rebutted. (Note the conspicuous absence of an "Offering public key:" line above.) Any suggestions?

  Read the article

• Can't make virtual host working

  - by sica07

  I have to create a virtual host on a server which, previously hosted a single website (domain name). Now I'm trying to add a second domain on this server (using the same nameserver). What I've done so far: Initially there was no virtual host so I've made one for the second domain: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /var/www/bla ServerName www.blabla.com ServerAlias blabla.com <Directory /var/www/blabla> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> Because nothing happend, I changed the DocumentRoot of the apache server to /var/www (initially was the root document of the first website -/var/www/html) and created a virtual host for the first domain too: <VirtualHost *:80> DocumentRoot /var/www/html ServerName www.first.com ServerAlias first.com <Directory /var/www/html> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> In this case, first.com is working ok, but bla.com not. When I ping blabla.com I get the "unkown host" response. What am I doing wrong? Do I have to modify something in the DNS settings too? Thank you.

  Read the article

• Sendmail delivering locally instead of to MTA in MX record

  - by CreativeNotice

  Ok, so I've got a box named websrv1.mydomain.com. It's a web server running ubuntu, apache2, sendmail, etc. My email is outsourced to a third party. So in my DNS I've got MX set to mx.thirdparty.net. I've no reason to accept incoming mail on my web server, every email should be sent to the third party. This works correctly accept with sending mail from the webserver (aka via cron or console). So from my web server, if I send an email to [email protected], it just disappears. No errors, nothing in dead.letter, nothing. I can send to any other address with no issues. If I send to [email protected] it's delivered locally which is fine. 1) Doing an nslookup shows the mx record is correct. 2) Running /mx mydomain.com from sendmail -bt returns the correct result. 3) Running sendmail -bv [email protected] returns: sudo sendmail -bv [email protected] [email protected]... deliverable: mailer esmtp, host mydomain.com., user [email protected] 4) Running 3,0 [email protected], returns: 3,0 [email protected] canonify input: me @ mydomain . com Canonify2 input: me Canonify2 returns: me canonify returns: me parse input: me Parse0 input: me Parse0 returns: me Parse1 input: me MailerToTriple input: me MailerToTriple returns: me Parse1 returns: $# esmtp $@ mydomain . com . $: me parse returns: $# esmtp $@ mydomain . com . $: me So I'm at a loss. Sendmail seems to see the mx record, but it's not using it.

  Read the article

• How To Remove Bottleneck with Squid Caching Proxy

  - by Volomike

  I'm more of a LAMP web developer trying to help the sysop. When I joined a project, I inherited some old PHP spaghetti code. Some of that code is that it goes out to a third-party website (let's call it thirdparty.com) and pulls down content with an HTTP-GET request. Unfortunately, the way the code is designed, it needs to do this several times a minute. When we looked at the bottlenecks on the server with 'netstat -a', we saw that connections to thirdparty.com were constantly running when this content would be plenty fine to be gathered once a day. What I need to know is if the Squid Proxy Caching Server is the solution we need? I'm guessing that this might let us have it pretend to be thirdparty.com on the network. If the web server needs to query thirdparty.com, it hits Squid instead. Squid can then determine whether it needs to supply content from cache or if it needs to go to thirdparty.com for fresh content. Is this the solution we need? And second, is this easily configured and only to cache thirdparty.com requests?

  Read the article

• ZFS - Impact of L2ARC cache device failure (Nexenta)

  - by ewwhite

  I have an HP ProLiant DL380 G7 server running as a NexentaStor storage unit. The server has 36GB RAM, 2 LSI 9211-8i SAS controllers (no SAS expanders), 2 SAS system drives, 12 SAS data drives, a hot-spare disk, an Intel X25-M L2ARC cache and a DDRdrive PCI ZIL accelerator. This system serves NFS to multiple VMWare hosts. I also have about 90-100GB of deduplicated data on the array. I've had two incidents where performance tanked suddenly, leaving the VM guests and Nexenta SSH/Web consoles inaccessible and requiring a full reboot of the array to restore functionality. In both cases, it was the Intel X-25M L2ARC SSD that failed or was "offlined". NexentaStor failed to alert me on the cache failure, however the general ZFS FMA alert was visible on the (unresponsive) console screen. The zpool status output showed: pool: vol1 state: ONLINE scan: scrub repaired 0 in 0h57m with 0 errors on Sat May 21 05:57:27 2011 config: NAME STATE READ WRITE CKSUM vol1 ONLINE 0 0 0 mirror-0 ONLINE 0 0 0 c8t5000C50031B94409d0 ONLINE 0 0 0 c9t5000C50031BBFE25d0 ONLINE 0 0 0 mirror-1 ONLINE 0 0 0 c10t5000C50031D158FDd0 ONLINE 0 0 0 c11t5000C5002C823045d0 ONLINE 0 0 0 mirror-2 ONLINE 0 0 0 c12t5000C50031D91AD1d0 ONLINE 0 0 0 c2t5000C50031D911B9d0 ONLINE 0 0 0 mirror-3 ONLINE 0 0 0 c13t5000C50031BC293Dd0 ONLINE 0 0 0 c14t5000C50031BD208Dd0 ONLINE 0 0 0 mirror-4 ONLINE 0 0 0 c15t5000C50031BBF6F5d0 ONLINE 0 0 0 c16t5000C50031D8CFADd0 ONLINE 0 0 0 mirror-5 ONLINE 0 0 0 c17t5000C50031BC0E01d0 ONLINE 0 0 0 c18t5000C5002C7CCE41d0 ONLINE 0 0 0 logs c19t0d0 ONLINE 0 0 0 cache c6t5001517959467B45d0 FAULTED 2 542 0 too many errors spares c7t5000C50031CB43D9d0 AVAIL errors: No known data errors This did not trigger any alerts from within Nexenta. I was under the impression that an L2ARC failure would not impact the system. But in this case, it surely was the culprit. I've never seen any recommendations to RAID L2ARC. Removing the bad SSD entirely from the server got me back running, but I'm concerned about the impact of the device failure (and maybe the lack of notification from NexentaStor as well). Edit - What's the current best-choice SSD for L2ARC cache applications these days?

  Read the article

• PHP unable to load dynamic library... but it is loaded. WTF?

  - by Josh

  I have a CentOS 5.4 server with Apache 2.2.3, mod_fastcgi and PHP 5.2.11. Everything is working great, server is a production server and I've had no complaints. When I was looking in PHP's error log to diagnose a problem with a specific page, I saw the following periodically repeated over and over: [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 I am very confused because APC is loaded, I can see it in the output of phpinfo(). And by the look of these error messages nothing should be working at all. Yet sites seem to be running fine. How can I track down the source of this error?

  Read the article

• Basic IP address structure

  - by dannymcc

  We currently have a few servers, around 30-40 workstations and 16 phones. Each device has a static IP address. As an example the standard settings for a new workstation is; IP: 192.168.1.XXX Subnet: 255.255.255.0 Gateway: 192.168.1.99 DNS: 192.168.1.50 As I am slowly exploring new server OS's and virtualisation etc. I am getting close to wanting a wider range of IP addresses. What I would like to do is seperate the devices by IP as follows: Servers 192.168.1.XXX Workstations 192.168.2.XXX Printers 192.168.3.XXX Phones 192.168.4.XXX VM's 192.168.5.XXX Is this a bad idea, or is this a common way of doing things? My biggest concern is the phones and subnet masks. The phones are managed by our provider although I have access to the server that runs them. Would I need to change the subnet mask to 255.255.0.0 on all devices? Or only those that change? For example, the phones don't need to connect to any other devices other than other phones and the phone server. So if I have the phones on 192.168.1.XXX with a subnet mask of 255.255.255.0 and then moved everything I had complete ownership/control of to 192.168.X.XXX with a new subnet mask of 255.255.0.0. Would that work?

  Read the article

• ESXI 5.1 - Unable to trunk to cisco switch

  - by Lance

  I have configured my esxi host vSwitch1 to use the secondary NIC on my VMware host. On vSwitch1 configuration I have set the VLAN to 4095 which specifies to allow all VLANs. If my cisco switch port configuration is set to an access port my server can ping the vlan interface on the switch. If my cisco switch port configuration is set to a trunk, whilst it stays UP UP and CDP information is available, I lose my ping from VMware VM server to the local vlan interface on the switch and I lose any server connectivity to my network. Switch NIC teaming policy to Route based on originating virtual port ID Configuration based on: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1006628 interface GigabitEthernet0/42 description Host Port switchport trunk encapsulation dot1q switchport trunk allowed vlan 18,220 switchport mode trunk switchport nonegotiate spanning-tree portfast trunk end Output from ESXI CLI esxcfg-vswitch -l: ~ # esxcfg-vswitch -l Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch0 128 5 128 1500 vmnic0 PortGroup Name VLAN ID Used Ports Uplinks VM Network 4095 1 vmnic0 Management Network 4095 1 vmnic0 Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch1 128 4 128 1500 vmnic1 PortGroup Name VLAN ID Used Ports Uplinks VM Network 2 4095 1 vmnic1 Any tips welcome!!!

  Read the article

• iSCSI, failover and XenServer

  - by jemmille

  I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

  Read the article

• client flips between internal and external IP addresses??

  - by jmiller-miramontes

  I have what seems like a not-particularly-complicated home network, all things considered: a DSL line comes in to a modem/router, which goes off to a switch, which supports a bunch of machines. My machines live in a 192.168.0.x address space; however, I'm running some public servers on the network, so I have a block of 8 (5, really) static IP addresses that are mapped to the servers by the router. The non-servers get 192.168.0.x addresses via NAT; some machines have static addresses and some get addresses from DHCP. Locally, I'm running a DNS server (named) to map between the domain names and the 192.168 address space. Somewhat messy, but everything basically works. Except: One of my local non-server clients occasionally switches from its internal address to its external address. That is, if I check the logs of a website I'm running internally, the hits coming from this client sometimes show up with the internal 192.168 address, and sometimes with the external (216.103...) address. It will flip back and forth for no apparent reason, without my doing anything. This can be a problem in terms of how the clients interact with the way I have some of the clients' SSH systems configured (e.g., allowing access from the internal network but not the external network), but it also Just Seems Wrong. I will confess that I'm kinda skating on the very edge of my networking competence here, but I can't for the life of me figure out what's going on. If it helps, the client in question is running Mac OS X / 10.6; its address is statically assigned, is not one of the five externally-accessible addresses, and gets its DNS from (first) the internal DNS server and (second) my ISP's DNS servers. I can't swear that none of the other NAT clients are also showing this problem; the one I'm dealing with is my everyday machine, so this is where I run into it. Does anybody out there have any advice? This is driving me crazy...

  Read the article

• Integration of SharePoint 2010 with TFS2010

  - by Kabir Rao

  We have performed following steps as of now- Install TFS2010 10.0.30319.1 (RTM) on Windows Server 2008 R2 Enterprise(app tier) SQL 2008 SP1 with Cumulative update 2 on Windows Server 2008 R2 Enterprise(data tier) Reporting Service is installed on app tier. After this installation worked fine we installed SharePoint 2010 on app tier. After installation we followed http://blogs.msdn.com/b/team_foundation/archive/2010/03/06/configuring-sharepoint-server-2010-beta-for-dashboard-compatibility-with-tfs-2010-beta2-rc.aspx for configuration. We are not able to perform the last step described in the link as following error occured- TF249063: The following Web service is not available: http://apptier:31254/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. The underlying error is: The remote server returned an error: (404) Not Found.. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://apptier:31254. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. We have also noticed that Document Folder in Team project also have red x. Please help. Thanks upfront.

  Read the article

• PHP running too slow, always showing "504 Gateway Time-out"

  - by komase

  PHP running too slow, always showing "504 Gateway Time-out" My server spec: Dual core ATOM 330 CPU 2GB RAM Use nginx with PHP in fastcgi use eaccelerator CPU 74.3%id RAM used: 350MB of 2GB I have lots of sites in my server, with cron running every minutes all time, even on some minutes, double or triple cron running at same time. All my sites cron is heavy, usually the cron running more than one minutes. my nginx.conf has become too big until nginx refuse to start because too many sites in it. it has been solved by increasing server_names_hash_max_size. Im planning to add more sites in my server Now, opening my website always showing 504 Gateway Time-out. I have tested many eaccelerator and PHP setting, but this 504 Gateway Time-out still happen. the 504 Gateway Time-out will dissappeared when cron is disabled I have no idea: is this because not enough processor power? And what should I do? upgrade my processor? --------added this is top for my CPU just now: Cpu(s): 17.5%us, 3.8%sy, 0.1%ni, 71.6%id, 6.9%wa, 0.1%hi, 0.1%si, 0.0%st

  Read the article

• IIS7 Compression CSS files only compressed when dynamic compression is enabled

  - by Paul

  If anyone can help it would be appreciated. I would like to enable compression for static files within IIS7 (for the sake of simplicity I'll just refer to static css files for the time being). The problem I'm getting is that css files are only compressed when both dynamic and static compression is enabled in IIS for the website. What I really want to achieve is css compression (static file) whilst leaving the dynamic (aspx) pages as uncompressed for the time being (to avoid unnecessary CPU load). I am puzzled as to why just leaving 'static compression' enabled causes css files to be returned uncompressed. My applicationHost.config file has not be altered and looks like this: <httpCompression directory="%SystemDrive%\inetpub\temp\IIS Temporary Compressed Files"> <scheme name="gzip" dll="%Windir%\system32\inetsrv\gzip.dll" /> <staticTypes> <add mimeType="text/*" enabled="true" /> <add mimeType="message/*" enabled="true" /> <add mimeType="application/javascript" enabled="true" /> <add mimeType="*/*" enabled="false" /> </staticTypes> <dynamicTypes> <add mimeType="text/*" enabled="true" /> <add mimeType="message/*" enabled="true" /> <add mimeType="application/x-javascript" enabled="true" /> <add mimeType="*/*" enabled="false" /> </dynamicTypes> </httpCompression> The server-wide compression setting within IIS is set to 'Dynamic Disabled' and 'Static Enabled' from the Server Features Compression page. The web-site compression setting (Server Sites MyWebsite Features Compression) is where I am enabling and disabling dynamic compression as detailed above. Any help would be really help me get unstuck on this. Thanks

  Read the article

• Configuring vsftpd with nginx on Ubuntu 12.04 LTS

  - by arby

  I've attempted to configure a nginx / vsftpd server on Ubuntu 12.04 LTS (via amazon ec2) a couple times now, but I seem to keep making a mistake along the way. Currently, when I try to connect to my ftp server it takes a minute or so before it connects. Then when I issue a command, they all timeout with an operation failed error. Aside from these issues, I'm not completely confident with the file ownership & permissions or the configuration / settings. So, I think it's best if I just re-install and re-configure correctly. I believe the nginx installation comes with a default user of www-data:www-data and web root directory ownership by root:root. Vsftpd, however, needs to have a user created with the same group as the nginx user (www-data), and the same home directory as the nginx server (/usr/share/nginx/www), with g+w chmod permissions granted on that directory. The vsftpd.conf file should disable anonymous logins and enable local logins, file writing, and chroot local users. In my previous config, I had /bin/false set for the ftp user's shell and pam_shells.so disabled. I also had local_umask set to 0027. So, starting with a fresh ec2 instance, I've got: sudo apt-get install vsftpd sudo apt-get install nginx For the firewall I issued the command (not sure if necessary): sudo ufw allow ftp Which commands / config is recommended from here? I only need 1 ftp user that I can use to login with my ftp client to modify the single nginx web domain, which will need php & sql for WordPress.

  Read the article

• Cannot push to GitHub from Amazon EC2 Linux instance

  - by Eli

  Having the worst luck push files to a repo from EC2 to GitHub. I have my ssh key setup and added to Github. Here are the results of ssh -v [email protected] OpenSSH_5.3p1, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /root/.ssh/identity type -1 debug1: identity file /root/.ssh/id_rsa type 1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5github2 debug1: match: OpenSSH_5.1p1 Debian-5github2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'github.com' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug1: Offering public key: /root/.ssh/id_rsa debug1: Remote: Forced command: gerve eliperelman 81:5f:8a:b2:42:6d:4e:8c:2d:ba:9a:8a:2b:9e:1a:90 debug1: Remote: Port forwarding disabled. debug1: Remote: X11 forwarding disabled. debug1: Remote: Agent forwarding disabled. debug1: Remote: Pty allocation disabled. debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: Trying private key: /root/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey).

  Read the article

• Alternatives to Splunk?

  - by MichaelGG

  I'm pretty impressed with Splunk, especially version 4. Pretty graphs, alerting (Enterprise only), and fast, accurate, searching. It's a great product. However, the cost just way too high to consider for full production use for our company. All we really need is to be able to index different logs in a central place, and have reasonable searching on that. Having alerts based on a saved search is also really nice. We don't really go beyond that. In fact, our biggest usage has been in deploying new applications. Everything gets logged via log4net to either the Event log on Windows or a text file on Linux. Splunk makes it pretty easy to quickly search across those to make sure all the parts of the app are working ok -- that's saved us tons of time versus hunting down individual logging sources. What alternatives exist in this market? I have a sinking feeling Splunk's pricing is so high because they have the best product by far, and they know it. We want the server to run on Windows. I'd be open to a split model, using one product for general logs (collect via syslog/Snare), and a dedicated product for our custom apps (like Log4Net Dashboard). Would using a simple syslog server such as Kiwi, sent to SQL Server (perhaps with fulltext enabled) work? I'd hope the cost should be well under 5 figures, USD. (And yes, I know, we're cheap. We're a startup with little money, and BizSpark takes care of all our MS licensing.) Edit: I should add, we have about 10 physical servers, 20 VMs, and a couple firewalls and switches. 90% is Windows.

  Read the article

• Send mail on event log error trigger safe check frequency

  - by Zeb Rawnsley

  I want to use powershell to alert me when an error occurs in the event viewer on my new Win2k12 Standard Server, I was thinking I could have the script execute every 10mins but don't want to put any strain on the server just for event log checking, here is the powershell script I want to use: $SystemErrors = Get-EventLog System | Where-Object { $_.EntryType -eq "Error" } If ($SystemErrors.Length -gt 0) { Send-MailMessage -To "[email protected]" -From $env:COMPUTERNAME + @company.co.nz" -Subject $env:COMPUTERNAME + " System Errors" -SmtpServer "smtp.company.co.nz" -Priority High } What is a safe frequency I can run this script at without hurting my server? Hardware: Intel Xeon E5410 @ 2.33GHz x2 32GB RAM 3x 7200RPM S-ATA 1TB (2x RAID1) Edit: With the help of Mathias R. Jessen's answer, I ended up attaching an event to the application & system log with the following script: Param( [string]$LogName ) $ComputerName = $env:COMPUTERNAME; $To = "[email protected]" $From = $ComputerName + "@company.co.nz"; $Subject = $ComputerName + " " + $LogName + " Error"; $SmtpServer = "smtp.company.co.nz"; $AppErrorEvent = Get-EventLog $LogName -Newest 1 | Where-Object { $_.EntryType -eq "Error" }; If ($AppErrorEvent.Length -eq 1) { $AppErrorEventString = $AppErrorEvent | Format-List | Out-String; Send-MailMessage -To $To -From $From -Subject $Subject -Body $AppErrorEventString -SmtpServer $SmtpServer -Priority High; };

  Read the article

• Setting Up VirtualHosts for a local RubyOnRails Application

  - by chris Frisina

  I want to set up a VirtualHost so that when I type the project name in the address bar, it goes to the home page of the project. httpd-vhosts.conf files in both XAMPP configuration and apache configuration: <VirtualHost project> ServerAdmin [email protected] ServerName project DocumentRoot /Users/path/to/project/public <Directory "/Users/path/to/project/public"> Options Includes FollowSymLinks AllowOverride All Order deny,allow Allow from all </Directory> RewriteEngine On RewriteOptions inherit </VirtualHost> I have also tried with the path directly to the project folder, and not the public folder of the project. the httpd.conf of XAMPP and apache : # Virtual hosts Include /Applications/XAMPP/etc/extra/httpd-vhosts.conf the /etc/hosts file: 127.0.0.1 other1 127.0.0.1 other2 127.0.0.1 project I have tried : 127.0.0.1 project 127.0.0.1:3000 project 127.0.0.1 project:3000 I have also restarted the rails server and the XAMPP server many times after changes. I have it working so that the project:3000/ works, but how do I get it so that I dont have to specify the port number? Notes: All other VHosts are working well. Rails 3.2.8 (willing to change) Ruby 1.9.3 WEBrick server

  Read the article

• FTP on Linux "Failed to retrieve directory listing" not firewall issue

  - by Jaka Prasnikar

  I've got an VPS in germany running Debian X64. I have very strange issue. I have ISPConfig CP installed using proftpd and I can not connect to FTP by any means. Few hours ago I've had installed DirectAdmin on CentOS same VPS and same issue. Simply when I connect to FTP server I get these: Status: Resolving address of web02.defikon.com Status: Connecting to 130.255.190.71:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 12:15. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER default1 Response: 331 User default1 OK. Password required Command: PASS ****** Response: 230-User default1 has group access to: client0 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Error: Connection timed out Error: Failed to retrieve directory listing I even tried telnet localhost 21 and the same happends. Once I issue command "LIST" I get time out. I've tried every thing and I can't get this to work =( Please help ! P.S.: iptables is turned off.

  Read the article

• Browser sends http request with RANGE

  - by nute

  I have a local testing environment in a Fedora virtual machine. Strangely, resources (css and js files) don't seem to work. Looking at Firebug, I see that the browser sends the HTTP request with "Range bytes=0-". The server responds with either an empty 200OK or an empty 206 Partial Content. Here is an example: Response Headers Date Mon, 23 Nov 2009 23:33:26 GMT Server Apache/2.2.13 (Fedora) Last-Modified Thu, 19 Nov 2009 22:58:55 GMT Etag "18-3aec-478c14dbee138" Accept-Ranges bytes Content-Length 15084 Content-Range bytes 0-15083/15084 Connection close Content-Type text/css Request Headers Host fedora.test User-Agent Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091105 Fedora/3.5.5-1.fc11 Firefox/3.5.5 Accept text/css,*/*;q=0.1 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://fedora.test/pictures/ Cookie __utma=26341546.1613992749.1258504422.1258569125.1258752550.4; __utmz=26341546.1258504422.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); PHPSESSID=tqf8jfmc77qihe97rl4tmhq685 Range bytes=0- If-Range "18-3aec-478c14dbee138" I don't know if the browser is sending the wrong request, or if it's the server that is doing this. Request made to the outside (such as google analytics) are working fine. This is running in Fedora 11 in VirtualBox. Apache. PHP. The files are being served through the "shared folders" feature of VirtualBox (could it be related?). No error logs could help me.

  Read the article

< Previous Page | 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246  | Next Page >