Search Results

Search found 72757 results on 2911 pages for 'load time'.

Page 133/2911 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • Unable to connect to server after a certain amount of time

    - by Troy
    I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

    Read the article

  • Hearing a clicking noise from soundcard all the time

    - by Mehrdad
    I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

    Read the article

  • Snow Leopard takes a long time to connect to Windows/Samba server

    - by hood
    We run a very heterogeneous network here: There is some XP, Vista, 7, Leopard, Snow Leopard clients, and Windows 2003 (one remaining legacy app), 2008, and Linux servers. The main file server runs Ubuntu Linux and has been added to the Windows Domain and has been used for many years; SBS 2008 is the PDC (the 2003 and 2008 are on the domain also). In Leopard there were no problems at all authenticating to the file servers. We've upgraded one of the Leopard iMacs to Snow Leopard, though the same problem occurs in a new MBP which came with the newer OS as well as a clean install on another iMac. It does not matter whether connected through wired or wireless. In the Finder when clicking on the server - whether on first boot or after it is connected - it will display "Connecting..." for up to a few minutes before either generally working (if username/password in keychain) or displaying "Connection Failed" - at which time clicking "Connect As" and typing in the username/password will take some more time and eventually work. Sometimes it will display "Connecting..." indefinitely. (I've left it as long as 15 minutes before trying something else) Accessing shares on the the 2003 and SBS servers have the problem (so I don't think it's a Samba server issue). The Server 2008 Standard is connecting instantly at the moment. Accessing the share through an alias/stacks doesn't have this problem. Leopard and Windows clients still have no problem. I've searched Google but hasn't yielded any working result. How do I get rid of this delay?

    Read the article

  • Perfmon % Processor Time vs. task manager's CPU usage

    - by nat
    I'm new to using Perfmon and performance monitoring in general (so go easy on me please ;) I know that Perfmon doesn't have anything exactly like Task Manager's CPU usage display, but I'm trying to figure out how to monitor user's CPU usage via Perfmon in a similar way, and trying to understand the measurements (or how to convert the numbers to get a similar understanding) For example, if in Task Manager, a particular user is consistently using more than 5% CPU, I would want to contact the user about it. I learn best by example, so here is exactly what I'm trying to do, with a specific example: This is for a 32-bit Dual Quad Core Windows 2003 web server (8 CPUs), there are many web sites on the server, each running within their own application pool/worker process ID. Through other research here I learned of a registry change that I made so that the PID shows up with the w3wp process so I can easily identify the site later by cross-referencing it. I set up a counter with the following settings: Process -> % Processor Time -> all instances Here is an example. Say I'm interested in "black line" user in this graph below, as his process is spiking quite high compared to all the other users: (I wasn't allowed to post the image as I'm a new user on this site.. I've uploaded the image to:) http://i35.tinypic.com/106yn8k.jpg So... using this as an example, I see that they have an AVERAGE % PROCESSOR TIME of 23.264 , and have spiked as high as 103.124 So what exactly does this 23.264 number mean to me? Is it similar to an average of Task Manager's CPU reading for this user? Or, since this server has 8 CPUs, should I divide this number by 8? (23.264/8 = 2.9% AVERAGE CPU LOAD?) Thanks in advance.

    Read the article

  • Could not load type 'Default.DataMatch' in DataMatch.aspx file

    - by salvationishere
    I am developing a C# VS 2008 / SQL Server 2008 website, but now I am getting the above error when I build it. I included the Default.aspx, Default.aspx.cs, DataMatch.aspx, and DataMatch.aspx.cs files below. What do I need to do to fix this? Default.aspx: <%@ Page Language="C#" MasterPageFile="~/Site.master" AutoEventWireup="true" CodeFile="Default.aspx.cs" Inherits="_Default" Title="Untitled Page" %> ... DataMatch.aspx: <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="DataMatch.aspx.cs" Inherits="_Default.DataMatch" %> ... Default.aspx.cs: using System; using System.Collections; using System.Configuration; using System.Data; using System.Linq; using System.Web; using System.Web.Security; using System.Web.UI; using System.Web.UI.HtmlControls; using System.Web.UI.WebControls; using System.Web.UI.WebControls.WebParts; using System.Xml.Linq; using System.Collections.Generic; using System.IO; using System.Drawing; using System.ComponentModel; using System.Data.SqlClient; using ADONET_namespace; using System.Security.Principal; //using System.Windows; public partial class _Default : System.Web.UI.Page //namespace AddFileToSQL { //protected System.Web.UI.HtmlControls.HtmlInputFile uploadFile; //protected System.Web.UI.HtmlControls.HtmlInputButton btnOWrite; //protected System.Web.UI.HtmlControls.HtmlInputButton btnAppend; protected System.Web.UI.WebControls.Label Label1; protected static string inputfile = ""; public static string targettable; public static string selection; // Number of controls added to view state protected int default_NumberOfControls { get { if (ViewState["default_NumberOfControls"] != null) { return (int)ViewState["default_NumberOfControls"]; } else { return 0; } } set { ViewState["default_NumberOfControls"] = value; } } protected void uploadFile_onclick(object sender, EventArgs e) { } protected void Load_GridData() { //GridView1.DataSource = ADONET_methods.DisplaySchemaTables(); //GridView1.DataBind(); } protected void btnOWrite_Click(object sender, EventArgs e) { if (uploadFile.PostedFile.ContentLength > 0) { feedbackLabel.Text = "You do not have sufficient access to overwrite table records."; } else { feedbackLabel.Text = "This file does not contain any data."; } } protected void btnAppend_Click(object sender, EventArgs e) { string fullpath = Page.Request.PhysicalApplicationPath; string path = uploadFile.PostedFile.FileName; if (File.Exists(path)) { // Create a file to write to. try { StreamReader sr = new StreamReader(path); string s = ""; while (sr.Peek() > 0) s = sr.ReadLine(); sr.Close(); } catch (IOException exc) { Console.WriteLine(exc.Message + "Cannot open file."); return; } } if (uploadFile.PostedFile.ContentLength > 0) { inputfile = System.IO.File.ReadAllText(path); Session["Message"] = inputfile; Response.Redirect("DataMatch.aspx"); } else { feedbackLabel.Text = "This file does not contain any data."; } } protected void Page_Load(object sender, EventArgs e) { if (Request.IsAuthenticated) { WelcomeBackMessage.Text = "Welcome back, " + User.Identity.Name + "!"; // Reference the CustomPrincipal / CustomIdentity CustomIdentity ident = User.Identity as CustomIdentity; if (ident != null) WelcomeBackMessage.Text += string.Format(" You are the {0} of {1}.", ident.Title, ident.CompanyName); AuthenticatedMessagePanel.Visible = true; AnonymousMessagePanel.Visible = false; if (!Page.IsPostBack) { Load_GridData(); } } else { AuthenticatedMessagePanel.Visible = false; AnonymousMessagePanel.Visible = true; } } protected void GridView1_SelectedIndexChanged(object sender, EventArgs e) { GridViewRow row = GridView1.SelectedRow; targettable = row.Cells[2].Text; } } DataMatch.aspx.cs: using System; using System.Collections; using System.Collections.Generic; using System.Data; using System.Data.SqlClient; using System.Diagnostics; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; using ADONET_namespace; //using MatrixApp; //namespace AddFileToSQL //{ public partial class DataMatch : AddFileToSQL._Default { protected System.Web.UI.WebControls.PlaceHolder phTextBoxes; protected System.Web.UI.WebControls.PlaceHolder phDropDownLists; protected System.Web.UI.WebControls.Button btnAnotherRequest; protected System.Web.UI.WebControls.Panel pnlCreateData; protected System.Web.UI.WebControls.Literal lTextData; protected System.Web.UI.WebControls.Panel pnlDisplayData; protected static string inputfile2; static string[] headers = null; static string[] data = null; static string[] data2 = null; static DataTable myInputFile = new DataTable("MyInputFile"); static string[] myUserSelections; static bool restart = false; private DropDownList[] newcol; int @temp = 0; string @tempS = ""; string @tempT = ""; // a Property that manages a counter stored in ViewState protected int NumberOfControls { get { return (int)ViewState["NumControls"]; } set { ViewState["NumControls"] = value; } } private Hashtable ddl_ht { get { return (Hashtable)ViewState["ddl_ht"]; } set { ViewState["ddl_ht"] = value; } } // Page Load private void Page_Load(object sender, System.EventArgs e) { if (!Page.IsPostBack) { ddl_ht = new Hashtable(); this.NumberOfControls = 0; } } // This data comes from input file private void PopulateFileInputTable() { myInputFile.Columns.Clear(); string strInput, newrow; string[] oneRow; DataColumn myDataColumn; DataRow myDataRow; int result, numRows; //Read the input file strInput = Session["Message"].ToString(); data = strInput.Split('\r'); //Headers headers = data[0].Split('|'); //Data for (int i = 0; i < data.Length; i++) { newrow = data[i].TrimStart('\n'); data[i] = newrow; } result = String.Compare(data[data.Length - 1], ""); numRows = data.Length; if (result == 0) { numRows = numRows - 1; } data2 = new string[numRows]; for (int a = 0, b = 0; a < numRows; a++, b++) { data2[b] = data[a]; } // Create columns for (int col = 0; col < headers.Length; col++) { @temp = (col + 1); @tempS = @temp.ToString(); @tempT = "@col"+ @temp.ToString(); myDataColumn = new DataColumn(); myDataColumn.DataType = Type.GetType("System.String"); myDataColumn.ColumnName = headers[col]; myInputFile.Columns.Add(myDataColumn); ddl_ht.Add(@tempT, headers[col]); } // Create new DataRow objects and add to DataTable. for (int r = 0; r < numRows - 1; r++) { oneRow = data2[r + 1].Split('|'); myDataRow = myInputFile.NewRow(); for (int c = 0; c < headers.Length; c++) { myDataRow[c] = oneRow[c]; } myInputFile.Rows.Add(myDataRow); } NumberOfControls = headers.Length; myUserSelections = new string[NumberOfControls]; } //Create display panel private void CreateDisplayPanel() { btnSubmit.Style.Add("top", "auto"); btnSubmit.Style.Add("left", "auto"); btnSubmit.Style.Add("position", "absolute"); btnSubmit.Style.Add("top", "200px"); btnSubmit.Style.Add("left", "400px"); newcol = CreateDropDownLists(); for (int counter = 0; counter < NumberOfControls; counter++) { pnlDisplayData.Controls.Add(newcol[counter]); pnlDisplayData.Controls.Add(new LiteralControl("<br><br><br>")); pnlDisplayData.Visible = true; pnlDisplayData.FindControl(newcol[counter].ID); } } //Recreate display panel private void RecreateDisplayPanel() { btnSubmit.Style.Add("top", "auto"); btnSubmit.Style.Add("left", "auto"); btnSubmit.Style.Add("position", "absolute"); btnSubmit.Style.Add("top", "200px"); btnSubmit.Style.Add("left", "400px"); newcol = RecreateDropDownLists(); for (int counter = 0; counter < NumberOfControls; counter++) { pnlDisplayData.Controls.Add(newcol[counter]); pnlDisplayData.Controls.Add(new LiteralControl("<br><br><br>")); pnlDisplayData.Visible = true; pnlDisplayData.FindControl(newcol[counter].ID); } } // Add DropDownList Control to Placeholder private DropDownList[] CreateDropDownLists() { DropDownList[] dropDowns = new DropDownList[NumberOfControls]; for (int counter = 0; counter < NumberOfControls; counter++) { DropDownList ddl = new DropDownList(); SqlDataReader dr2 = ADONET_methods.DisplayTableColumns(targettable); ddl.ID = "DropDownListID" + counter.ToString(); int NumControls = targettable.Length; DataTable dt = new DataTable(); dt.Load(dr2); ddl.DataValueField = "COLUMN_NAME"; ddl.DataTextField = "COLUMN_NAME"; ddl.DataSource = dt; ddl.SelectedIndexChanged += new EventHandler(ddlList_SelectedIndexChanged); ddl.DataBind(); ddl.AutoPostBack = true; ddl.EnableViewState = true; //Preserves View State info on Postbacks dr2.Close(); ddl.Items.Add("IGNORE"); dropDowns[counter] = ddl; } return dropDowns; } protected void ddlList_SelectedIndexChanged(object sender, EventArgs e) { DropDownList ddl = (DropDownList)sender; string ID = ddl.ID; } // Add TextBoxes Control to Placeholder private DropDownList[] RecreateDropDownLists() { DropDownList[] dropDowns = new DropDownList[NumberOfControls]; for (int counter = 0; counter < NumberOfControls; counter++) { DropDownList ddl = new DropDownList(); SqlDataReader dr2 = ADONET_methods.DisplayTableColumns(targettable); ddl.ID = "DropDownListID" + counter.ToString(); int NumControls = targettable.Length; DataTable dt = new DataTable(); dt.Load(dr2); ddl.DataValueField = "COLUMN_NAME"; ddl.DataTextField = "COLUMN_NAME"; ddl.DataSource = dt; ddl.SelectedIndexChanged += new EventHandler(ddlList_SelectedIndexChanged); ddl.DataBind(); ddl.AutoPostBack = true; ddl.EnableViewState = false; //Preserves View State info on Postbacks dr2.Close(); ddl.Items.Add("IGNORE"); dropDowns[counter] = ddl; } return dropDowns; } private void CreateLabels() { for (int counter = 0; counter < NumberOfControls; counter++) { Label lbl = new Label(); lbl.ID = "Label" + counter.ToString(); lbl.Text = headers[counter]; lbl.Style["position"] = "absolute"; lbl.Style["top"] = 60 * counter + 10 + "px"; lbl.Style["left"] = 250 + "px"; pnlDisplayData.Controls.Add(lbl); pnlDisplayData.Controls.Add(new LiteralControl("<br><br><br>")); } } // Add TextBoxes Control to Placeholder private void RecreateLabels() { for (int counter = 0; counter < NumberOfControls; counter++) { Label lbl = new Label(); lbl.ID = "Label" + counter.ToString(); lbl.Text = headers[counter]; lbl.Style["position"] = "absolute"; lbl.Style["top"] = 60 * counter + 10 + "px"; lbl.Style["left"] = 250 + "px"; pnlDisplayData.Controls.Add(lbl); pnlDisplayData.Controls.Add(new LiteralControl("<br><br><br>")); } } // Create TextBoxes and DropDownList data here on postback. protected override void CreateChildControls() { // create the child controls if the server control does not contains child controls this.EnsureChildControls(); // Creates a new ControlCollection. this.CreateControlCollection(); // Here we are recreating controls to persist the ViewState on every post back if (Page.IsPostBack) { RecreateDisplayPanel(); RecreateLabels(); } // Create these conrols when asp.net page is created else { PopulateFileInputTable(); CreateDisplayPanel(); CreateLabels(); } // Prevent dropdownlists and labels from being created again. if (restart == false) { this.ChildControlsCreated = true; } else if (restart == true) { this.ChildControlsCreated = false; } } private void AppendRecords() { switch (targettable) { case "ContactType": for (int r = 0; r < myInputFile.Rows.Count; r++) { resultLabel.Text = ADONET_methods.AppendDataCT(myInputFile.Rows[r], ddl_ht); } break; case "Contact": for (int r = 0; r < myInputFile.Rows.Count; r++) { resultLabel.Text = ADONET_methods.AppendDataC(myInputFile.Rows[r], ddl_ht); } break; case "AddressType": for (int r = 0; r < myInputFile.Rows.Count; r++) { resultLabel.Text = ADONET_methods.AppendDataAT(myInputFile.Rows[r], ddl_ht); } break; default: resultLabel.Text = "You do not have access to modify this table. Please select a different target table and try again."; restart = true; break; //throw new ArgumentOutOfRangeException("targettable type", targettable); } } // Read all the data from TextBoxes and DropDownLists protected void btnSubmit_Click(object sender, System.EventArgs e) { //int cnt = FindOccurence("DropDownListID"); AppendRecords(); pnlDisplayData.Visible = false; btnSubmit.Visible = false; resultLabel.Attributes.Add("style", "align:center"); btnSubmit.Style.Add("top", "auto"); btnSubmit.Style.Add("left", "auto"); btnSubmit.Style.Add("position", "absolute"); int bSubmitPosition = NumberOfControls; btnSubmit.Style.Add("top", System.Convert.ToString(bSubmitPosition)+"px"); resultLabel.Visible = true; Instructions.Visible = false; if (restart == true) { CreateChildControls(); } } private int FindOccurence(string substr) { string reqstr = Request.Form.ToString(); return ((reqstr.Length - reqstr.Replace(substr, "").Length) / substr.Length); } #region Web Form Designer generated code override protected void OnInit(EventArgs e) { // // CODEGEN: This call is required by the ASP.NET Web Form Designer. // InitializeComponent(); base.OnInit(e); } /// <summary> /// Required method for Designer support - do not modify /// the contents of this method with the code editor. /// </summary> private void InitializeComponent() { } #endregion } //}

    Read the article

  • Openswan + xl2tpd connections time out after a while

    - by Halfgaar
    I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

    Read the article

  • HTTP downloads stop after some time, resuming is not possible

    - by cdauth
    When I try to download a file via HTTP, the downloads sometimes stop after around 30 MB. The download rates goes down to 0 B/s and no data keeps coming. When I stop the download and resume again, the download still hangs. But when I redownload it from byte 0 again, everything works fine up to 30 MB when it stops again. Sometimes, after some hours, it just works again without problems. The position in the file when the download stops is variable, but most of the time it is around 30–35 MB. As a download manager I use wget. The same behaviour happens though using curl and other download managers. The error occurs independently of the server I download from. I have also observed this error on other Linux computers in my network. All computers on my network run Gentoo Linux on x86. All internet connections on my network go through a server on my network which runs a transparent Squid proxy on port 80. That server is connected to a router, which is a Speedport W 700V by Deutsche Telekom AG. That router is connected to the internet using ADSL, with 448 kbit/s down speed and 96 kbit/s up speed. I am almost sure that my transparent proxy is not the problem. I turned that off without resolving the issue. I also connected to the router directly via WLAN without resolving the issue. I also tried to download over another port via HTTP. Furthermore, I tried to download the file using IPv6 with a gateway6 tunnel from my computer, which resulted in exactly the same problem. Now the strange thing is that everything works fine using FTP and HTTPS (also with wget on the same computer). Even more strange: when I resume the download that hanged over HTTP using FTP or HTTPS, download a few bytes that way, stop wget and then resume again using HTTP, it loads data again! But after a few MB, it may stop again. Unfortunately, files downloaded that way are always broken (the MD5 sum is not correct), so at some point, there must have been bogus data. I tried searching for HTML error messages in the downloaded file, but grep -i html does not find anything. (I cannot think of a way to search for GZIP-compressed HTML error messages in the file, so I did not try that.) I tried using strace on wget when it failed to resume a download, you can find the entire output on pastebin. The important lines are repeated every second: clock_gettime(CLOCK_MONOTONIC, {326102, 62176435}) = 0 ) = 1 write(2, "78% [++++++++++++++++++++++++++++"..., 19578% [+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ] 110,683,685 --.-K/s ) = 195 select(4, [3], NULL, NULL, {0, 949999}) = 0 (Timeout) I have absolutely no idea what could be the reason of this problem. It seems like whatever causes the issue speaks HTTP. It seems to speak HTTP that intelligently that it even regognises it in an IPv6-over-IPv4 tunnel. But what could that be and why does it only happen sometimes? The other possibility would be that there is a problem on my computer that is the same on other Gentoo Linux computers as well. Has anyone ever had such a problem? What could be the reason and where do I have to continue investigating to find out more about the issue? Update: I have just run into the problem again and tried to resume the download over the router’s WLAN, and this time it worked. Maybe I did something wrong during my last tests with the WLAN. Now maybe my transparent proxy server is in fact the problem. It is a very basic Squid proxy server that does not cache anything. Maybe the fact is interesting that a second Squid proxy runs on the same computer on another port. Update: A download hung again and this time I turned off all firewall settings and stopped all proxy servers. I failed to resume the download from my network server, which is directly connected to the router. So my proxy server definitely is not the cause the problem. I will try to upgrade the firmware of my router now, although I do not have admin access to it. I will see what I can do.

    Read the article

  • Problems deploying MVC2 - Could not load type 'System.Web.Mvc.UrlParameter'

    - by Evgeny
    Hi Everyone, I have problems deploying MVC2 application to my hosting. It shows the following error: Could not load type 'System.Web.Mvc.UrlParameter' from assembly 'System.Web.Mvc, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35'. It looks like it does not understand the new "optional URL parameters" feature of MVC2. This is just a simple test application I created with "New Project" wizard in VWD 2008. It works ok localy both in IIS and Visual Studio web servers. MVC1 web sites are working ok on the hosting server. I've contacted the hosting support and they installed MVC2 but the problem still exists. The web site is working in ASP.NET 2.0 integrated pipeline mode. Does anyone know why it is happening? Thank you!

    Read the article

  • Parser Error Message: Could not load type 'TestMvcApplication.MvcApplication'

    - by Riaan Engelbrecht
    I am getting the following error on one of our production servers. Not sure why it is working on the DEV server? Parser Error Description: An error occurred during the parsing of a resource required to service this request. Please review the following specific parse error details and modify your source file appropriately. Parser Error Message: Could not load type 'TestMvcApplication.MvcApplication'. Source Error: Line 1: <%@ Application Codebehind="Global.asax.cs" Inherits="TestMvcApplication.MvcApplication" Language="C#" % Source File: /global.asax Line: 1 Not sure if anybody came across this error before and how it was solved, but I have reached the end. Any help would be appreciated. I also need to mention that this is the published code, so all is compiled. Can there be something wrong with my compiler settings?

    Read the article

  • jquery .live on load event

    - by bandhunt
    I need a way to use the jquery .live() function to act on elements that are loaded via ajax. For instance a div is loaded via ajax .load() <div id="mydiv"></div> Normally I do .live() with a click event, but I need to know how to tell the dom that this new div has loaded without any explicit actions/events from the user. This code doesn't work, but I want to do something like this: mydiv = $("#mydiv"); mydiv.live("mydiv.length > 0", function() { // do something }); The "mydiv.length" being a substitue for the typical "click" or other event.

    Read the article

  • How to eager load in WCF Ria Services/Linq2SQLDomainModel

    - by Aggelos Mpimpoudis
    I have a databound grid at my view (XAML) and the Itemsource points to a ReportsCollection. The Reports entity has three primitives and some complex types. These three are shown as expected at datagrid. Additionally the Reports entity has a property of type Store. When loading Reports via GetReports domain method, I quickly figure out that only primitives are returned and not the whole graph of some depth. So, as I wanted to load the Store property too, I made this alteration at my domain service: public IQueryable<Report> GetReports() { return this.ObjectContext.Reports.Include("Store"); } From what I see at the immediate window, store is loaded as expected, but when returned to client is still pruned. How can this be fixed? Thank you!

    Read the article

  • ruby1.9.1 - sqlite3 problem on ubuntu 9.10 x64 (no such file to load -- sqlite3)

    - by doriath
    Hi, I have problem with sqlite3, because it is not working. irb(main):001:0> require 'sqlite3' LoadError: no such file to load -- sqlite3 from (irb):1:in `require' from (irb):1 from /usr/bin/irb:12:in `<main>' I have installed following packages: sudo apt-get install ruby1.9.1-full sudo apt-get install rubygems1.9.1 sudo gem update --system sudo apt-get install sqlite3 libsqlite3-dev sudo gem install sqlite3-ruby sudo apt-get install libopenssl-ruby1.9.1 The applications has following versions: $ ruby --version ruby 1.9.1p243 (2009-07-16 revision 24175) [x86_64-linux] $ sqlite3 --version 3.6.16 $ gem --version 1.3.6 and $ gem list --local *** LOCAL GEMS *** actionmailer (2.3.5) actionpack (2.3.5) activerecord (2.3.5) activeresource (2.3.5) activesupport (2.3.5) ffi (0.6.2) rack (1.0.1) rails (2.3.5) rake (0.8.7) rubygems-update (1.3.6) sqlite3-ruby (1.2.5) What have I missed?

    Read the article

  • How to load a UIView from a NIB?

    - by Winder
    I have been using UIViewControllers and initWithNibName with much success, basically using them as a convenient way to design the view with Interface Builder. Unfortunately I have built a hierarchy of views before noticing this line in the UIViewController documentation: Note: You should not use view controllers to manage views that fill only a part of their window My question is this: Having a very simple NIB that only has a UIView in addition to the default First Responder and Owning Object, what is the simplest way to load the UIView into my code? I have not been able to get loadNibNamed:owner:options: to work at this point, but suspect the answer will involve it somehow.

    Read the article

  • How to set focus to a textbox on page load event

    - by Kalpana
    I am trying to set focus to the text box on page load event. I tried many solutions by referring the element id, but couldn't able to focus the element. Later when I inspect the element using firebug I found for the same element the id changes in different execution. I am looking for the simplest solution using javascript or jquery to achieve this <h:form id="form"> <rich:dataTable value="#{books}" var="book"> <ui:repeat value="#{authors}" var="author"> <h:inputText value="#{author.name}"/> </ui:repeat> </rich:dataTable> </h:form>

    Read the article

  • Load application context problem in Maven managed spring-test TestNg

    - by joejax
    I try to setup a project with spring-test using TestNg in Maven. The code is like: @ContextConfiguration(locations={"test-context.xml"}) public class AppTest extends AbstractTestNGSpringContextTests { @Test public void testApp() { assert true; } } A test-context.xml simply defined a bean: <bean id="app" class="org.sonatype.mavenbook.simple.App"/> I got error for Failed to load ApplicationContext when running mvn test from command line, seems it cannot find the test-context.xml file; however, I can get it run correctly inside Eclipse (with TestNg plugin). So, test-context.xml is under src/test/resources/, how do I indicate this in the pom.xml so that 'mvn test' command will work? Thanks, UPDATE: Thanks for the reply. Cannot load context file error was caused by I moved the file arround in different location since I though the classpath was the problem. Now I found the context file seems loaded from the Maven output, but the test is failed: Running TestSuite May 25, 2010 9:55:13 AM org.springframework.beans.factory.xml.XmlBeanDefinitionReader loadBeanDefinitions INFO: Loading XML bean definitions from class path resource [test-context.xml] May 25, 2010 9:55:13 AM org.springframework.context.support.AbstractApplicationContext prepareRefresh INFO: Refreshing org.springframework.context.support.GenericApplicationContext@171bbc9: display name [org.springframework.context.support.GenericApplicationContext@171bbc9]; startup date [Tue May 25 09:55:13 PDT 2010]; root of context hierarchy May 25, 2010 9:55:13 AM org.springframework.context.support.AbstractApplicationContext obtainFreshBeanFactory INFO: Bean factory for application context [org.springframework.context.support.GenericApplicationContext@171bbc9]: org.springframework.beans.factory.support.DefaultListableBeanFactory@1df8b99 May 25, 2010 9:55:13 AM org.springframework.beans.factory.support.DefaultListableBeanFactory preInstantiateSingletons INFO: Pre-instantiating singletons in org.springframework.beans.factory.support.DefaultListableBeanFactory@1df8b99: defining beans [app,org.springframework.context.annotation.internalCommonAnnotationProcessor,org.springframework.context.annotation.internalAutowiredAnnotationProcessor,org.springframework.context.annotation.internalRequiredAnnotationProcessor]; root of factory hierarchy Tests run: 3, Failures: 2, Errors: 0, Skipped: 1, Time elapsed: 0.63 sec If I use spring-test version 3.0.2.RELEASE, the error becomes: org.springframework.test.context.testng.AbstractTestNGSpringContextTests.springTestContextPrepareTestInstance() is depending on nonexistent method null Here is the structure of the project: simple |-- pom.xml `-- src |-- main | `-- java `-- test |-- java `-- resources |-- test-context.xml `-- testng.xml testng.xml: <suite name="Suite" parallel="false"> <test name="Test"> <classes> <class name="org.sonatype.mavenbook.simple.AppTest"/> </classes> </test> </suite> test-context.xml: <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.0.xsd" default-lazy-init="true"> <bean id="app" class="org.sonatype.mavenbook.simple.App"/> </beans> In the pom.xml, I add testng, spring, and spring-test artifacts, and plugin: <dependency> <groupId>org.testng</groupId> <artifactId>testng</artifactId> <version>5.1</version> <classifier>jdk15</classifier> <scope>test</scope> </dependency> <dependency> <groupId>org.springframework</groupId> <artifactId>spring</artifactId> <version>2.5.6</version> </dependency> <dependency> <groupId>org.springframework</groupId> <artifactId>spring-test</artifactId> <version>2.5.6</version> <scope>test</scope> </dependency> <build> <finalName>simple</finalName> <plugins> <plugin> <artifactId>maven-compiler-plugin</artifactId> <configuration> <source>1.6</source> <target>1.6</target> </configuration> </plugin> <plugin> <groupId>org.apache.maven.plugins</groupId> <artifactId>maven-surefire-plugin</artifactId> <configuration> <suiteXmlFiles> <suiteXmlFile>src/test/resources/testng.xml</suiteXmlFile> </suiteXmlFiles> </configuration> </plugin> </plugins> Basically, I replaced 'A Simple Maven Project' Junit with TestNg, hope it works.

    Read the article

  • Java web start - Unable to load resource

    - by CD
    Hi all, I've got a jar that loads great with java web starter when I browse through the IP address of the server. Once I try the server name instead I get the following exception: com.sun.deploy.net.FailedDownloadException: Unable to load resource: at com.sun.deploy.net.DownloadEngine.actionDownload(Unknown Source) at com.sun.deploy.net.DownloadEngine.getCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResourceCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResourceCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResource(Unknown Source) at com.sun.javaws.LaunchDownload$DownloadTask.call(Unknown Source) at java.util.concurrent.FutureTask$Sync.innerRun(Unknown Source) at java.util.concurrent.FutureTask.run(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Any idea what should I look for?

    Read the article

  • Load CoreData objects' string property into UIPickerView

    - by OscarTheGrouch
    Hello Currently I have an entity named "Events" in a CoreData app. "Events" has one string property named "eventName". In the -(void)viewDidLoad I am trying to Fetch all the "Events" objects and load their "eventName" by alphabetical order into a UIPickerView. The ultimate end goal is through the use of a textField, buttons and the pickerView being add new objects in and remove unwanted objects out. Basically turning the UIPickerView into a UITableView. Currently I am able to save objects to the CoreData store, but am not able to pull them/their properties out into the UIPickerView. I am willing and able to share the project source code to anyone who wants it, or is willing to look at it to help out. thanks Chris

    Read the article

  • Load NSImage into QPixmap or QImage

    - by Thomi
    I have an NSImage pointer from a platform SDK, and I need to load it into Qt's QImage class. To make things easier, I can create a QImage from a CGImageRef by using QPixmap as an intermediate format, like this: CGImageRef myImage = // ... get a CGImageRef somehow. QImage img = QPixmap::fromMacCGImageRef(myImage).toImage(); However, I cannot find a way to convert from an NSImage to a CGImageRef. Several other people have had the same problem, but I have yet to find a solution. There is the CGImageForProposedRect method, but I can't seem to get it to work. I'm currently trying this (img is my NSImage ptr): CGImageRef ir = [img CGImageFirProposedRect:0:0:0]; Any ideas?

    Read the article

  • midl.exe cannot load mscorlib.tlb

    - by Akash
    I'm trying to use midl to turn an idl file into a tlb. However, when I try I get this warning: warning MIDL2015: failed to load tlb in importlib : mscorlib.tlb and I then get a subsequent error: error MIDL2337 : unsatisfied forward declaration : _Object..... I'm certain that the error is due to the first warning. I've tried the same command on a different machine and it succeeds, so I know that the idl file is correct. I've tried uninstalling the .NET framework and reinstalling it in the hope that that would fix things, but it had no effect. So my question is, what do I need to fix on my machine to allow midl to locate mscorlib.tlb once more?

    Read the article

  • ASP.NET Load unmanaged dll from bin folder

    - by Quandary
    Question: I use an embedded Firebird database in ASP.NET. Now, Firebird has a .NET wrapper around native dlls. The problem is, with the .NET compilation and execution process, the dlls get shadow copied to a temporary folder. Unfortunately, only the .NET dlls, and not the native dll. See http://msdn.microsoft.com/en-us/library/ms366723.aspx for details. Now, this makes it necessary to put the unmanaged dll somewhere into the system32 directory (or any other directory in the path environment variable). Now, I want to change the wrapper/native dll (opensource), so it loads the dll also if they are only in the bin folder. Now, my problem is, how can I, in .NET, load an unmanaged dll from an absolute path ? The absolute path is determined at runtime, not at compile-time...

    Read the article

  • Dynamically load nib for iPhone/iPad within view controller

    - by qui
    Hello I have converted an iPhone application using the wizard like thing in XCode into a universal app. It builds fine but obviously looks a bit rubbish in some areas :) I need to load nibs according to which device is being used. I dont wish to create my view controllers using initWithNib as I already have code to create the controllers with some data (initWithMyLovelyData) which doesnt do anything to do with nib loading. I know to find out the device you use UI_USER_INTERFACE_IDIOT() so I tried overriding the initWithNibName within the actual view controllers themselves, assuming they get called internally somehow. But it's not working as I guess I am unsure of the syntax. I have tried if(ipad..) self = [super initWithNibName:@"MyIpadNib" bundle:nibBundleOrNil]; And that doesnt work :/ EDIT - I know I have massively edited this, made my question a bit more specific after doing some more research - apologies!

    Read the article

  • Assembly Microsoft.Xna.Framework.dll does not load

    - by jbsnorro
    When trying to load Microsoft.Xna.Framework.dll from any project, it throws a FileNotFoundException. The specified module could not be found. (Exception from HRESULT: 0x8007007E), with no innerException. Even the simple code like the following throws that exception: static void Main(string[] args) { Assembly.LoadFile(@"C:\Microsoft.Xna.Framework.dll"); } I run XP x64, but I've set the platform in the configuration manager to x86, because I know it shouldn't(doesn't) work on x64 or Any CPU. I've manually added the dll file to GAC, but that didn't solve the problem. I have also tried the M$ Assembly Binding Log Viewer to see if those logs had any useful information, but they didn't. Everything, the loading etc, was a success according to them. Any suggestions? please?

    Read the article

  • Issit possible to load a UIVIewcontroller from uiview of another UIViewController

    - by chako89
    Guys, need your advise here. I have: an UIViewController A UIView B: I added subview which is a UIView to the UIViewController A an UIViewController C What I did is: in UIViewController A's viewDidLoad's method, I call this: UIView *subviewB = [[Subview alloc] initWithFrame:CGRectMake(0, 0, 1024, 768)]; [subviewB subviewBMethod]; // [self.view addSubview:rsubviewB]; SubviewBMethod code is to create an view, inside this view have a button. Once this button is clicked, it will change to UIViewController C. I tried this: [self presentModalViewController:self.UIViewControllerC animated:YES]; And I got this error message: warning: incompatible Objective-C types 'struct UIViewControllerC *', expected 'struct UIViewController *' when passing argument 1 of 'presentModalViewController:animated:' from distinct Objective-C type When I run the app, it terminates immediately when I click the button, I opened the console bug, there is no any error message. My method must be wrong, thus my question is: Issit possible to load a UIVIewcontroller from uiview of another UIViewController? If: Yes: How to do it? No: What should I do? THank you =)

    Read the article

  • Could not load file or assembly

    - by sldevelop
    Hi guys, I'm tring to create a generic collection of dynamic type at runtime of Silverlight application. My code: Type listType = Type.GetType("System.Collections.ObjectModel.ObservableCollection`1[[" + type.AssemblyQualifiedName + "]], System.Windows, Version=2.0.5.0, Culture=neutral, PublicKeyToken=7cec85d7bea7798e", true); type - is variable of Type type. That Type is creating at runtime. At that code line I've got error: Could not load file or assembly ', Version=0.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. The system cannot find the file specified. How can I resolve that error?

    Read the article

  • How can resolve Error: "Could not load type 'Microsoft.SharePoint.WebControls.SPGridView" SharePoin

    - by ricky roy
    Following error comes when creating a WebPart In sharePoint 2010 Server. Web Part Error: Unhandled exception was thrown by the user code wrapper's Execute method in the partial trust app domain: System.Web.HttpUnhandledException: Exception of type 'System.Web.HttpUnhandledException' was thrown. --- System.TypeLoadException: Could not load type 'Microsoft.SharePoint.WebControls.SPGridView' from assembly 'Microsoft.SharePoint, Version=14.900.0.0, Culture=neutral, PublicKeyToken=71e9bce111e9429c'. at ListMenuSample.ListMenuSample.ListMenuSample.CreateChildControls() at System.Web.UI.Control.EnsureChildControls() at System.Web.UI.Control.PreRenderRecursiveInternal() at System.Web.UI.Control.PreRenderRecursiveInternal() at System.Web.UI.Control.PreRenderRecursiveInternal() at System.Web.UI.Control.PreRenderRecursiveInternal() at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) --- End of inner exception stack trace --- at System.Web.UI.Page.HandleError(Exception e) at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) at System.Web.UI.Page.ProcessRequest(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) at System.Web.UI.Page.ProcessRequest() at System.Web.UI.Page.ProcessRequest(HttpContext context) at Microsoft.SharePoint.UserCode.SPUserCodeWebPartWrapper.ExecuteHttpRequest(SPUserCodeWebPartHttpRequestContext webPartExecutionContext, SPUserCodeWebPartHttpResponse httpRequestResponse) at Microsoft.SharePoint.UserCode.SPUserCodeWebPartWrapper.Execute(SPUserCodeExecutionContext executionContext) at Microsoft.SharePoint.UserCode.SPUserCodeApplicationHostAppDomainRef.Execute(Type userCodeWrapperType, SPUserCodeCachedAssemblyGroup userAssemblyGroup, Guid siteCollectionId, Byte[] binaryUserCodeToken, Byte[] proxyOperationToken, SPUserCodeExecutionContext executionContext) Thanks & Regards, Basant

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >