Search Results

Search found 5564 results on 223 pages for 'multi gpu'.

Page 136/223 | < Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >

• Is the exhaust fan necessary?

  - by Borek

  On my new PC, the component making the most noise is the rear exhaust fan on my case (it is the only exhaust fan in my PC). I tried to disconnect it and watched temperatures in SpeedFan and CPU was usually at about 35C, peaking to about 50C when the system was under load - this doesn't look too bad. So I'm considering that I'll leave the exhaust fan disconnected permanently after which the computer is very quiet - the only noise-making components are Arctic Cooling Freezer 7 Pro Rev.2 (CPU fan) and PSU fan (Enermax Pro 82+), both being quiet enough as far as I can tell. (My GPU has a passive cooler.) Also, those 2 components are moving parts so will provide some air flow in the case and, even better, PSU fan sucks the air out of the case so it kind of is an exhaust fan in itself. Does anyone run with the exhaust fan disconnected? You don't have to tell me that it's always better to have more air flow than less, I know that, but the noise is also a consideration for me and temperatures around 40C should be fine shouldn't they? (I might also consider getting a quieter case fan but I'm specifically interested in your opinion on the no exhaust fan scenario.)

  Read the article

• How can I stop Flash from leaving full-screen mode when it loses focus due to a mouse-click in the o

  - by therefromhere

  On a multi-monitor system, if I'm viewing a full-screen video in Flash on one monitor, clicking the mouse on the other monitor causes Flash to leave full-screen mode and revert to normal size. What's the easiest way of preventing this that works on my version of Flash? My system is Flash 10 (10.0.12.36), in Firefox 3.5 on Windows Vista 64, but I think it affects all current versions. This is very annoying behaviour, but unfortunately, according to this bug report response it seem to be a security feature, rather than a bug: We understand that many users would like fullscreen on one monitor and to be able to interact with your OS on another monitor. However, due to security requirements, we require that Flash and Browser must be the current focus of your OS.

  Read the article

• Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

  - by Patrick

  While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

  Read the article

• Rolling Back Microsoft CRM during testing

  - by npeterson

  Process related question: Currently we have a multi-tenant installation of MS CRM 4.0 on three servers, Dev, Test, and Live. We are actively working on customizing one of the tenants, but the others are static. During user testing, we often find it necessary to 'start fresh' in one of the tenants. Is it better to try and delete out the changes from the tenant (created accounts, leads, etc), or just revert the database to a backup from before the testing started? Is there compelling reasons why bulk delete is not advisable for MSCRM or that reverting the database frequently could cause issue?

  Read the article

• Debian: What are these files in /sys/devices/pci0000:00/ for?

  - by muhuk

  I am running Debian Squeeze on an MSI M670 laptop. I have these following files on my root drive, each 256MB: file:///sys/devices/pci0000:00/0000:00:05.0/resource1 file:///sys/devices/pci0000:00/0000:00:05.0/resource1_wc Here is my lspci output: muhuk@debian:~$ lspci 00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51 [GeForce Go 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: nVidia Corporation MCP51 PMU (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 04:04.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 04:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 04:04.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 04:09.0 Network controller: RaLink RT2561/RT61 rev B 802.11g I am speculating these have something to do with the shared RAM my GPU is using. But why a file on disk? And why two of them?

  Read the article

• My Computer hangs for a few minutes just after startup, and then is fine.

  - by EvilChookie

  So I just built myself a reasonably beefy computer, and I installed Windows 7 on it. However, I start the machine up each morning and within a few minutes, the computer will semi hang. That is the mouse is responsive, and most of the time I can open task manager, or a new tab in Chrome. Occasionally windows will be labelled as 'Not responding'. Then, the machine will get over it's problem, and will be nice and quick until I turn it off. Here's my specs: CPU: AMD Phenom-II X4 955 Black (Quad Core, 3.2ghz) RAM: 4GB of DDR3 1300 MOBO: ASUS M4A785T-M (Latest BIOS) HARD DRIVES: 2x1TB Western Digital Caviar Blacks in RAID-0. OS: Windows 7 Ultimate x64. GPU: ASUS GT240 1GB. I believe this issue relates to the RAID array, as I didn't have the lockup problem before I created the array. I purchased a second drive and reformatted after creating a RAID array, since the single drive was a little on the pokey side (compared to the rest of the computer). What I have tried: Updated Raid Drivers Malware checks Windows Updates Unecessary Services CPU and Disk activity appears to be low (via Resource Monitor) No strange errors in the error log. Any thoughts?

  Read the article

• Troubleshooting: Monitor never turns on, system fans running, DVD-ROM does not open.

  - by Wesley

  Hi all, Here are my specs beforehand: ECS P4VXASD2+ (V5.0) motherboard FSB 533MHz Intel Pentium 4 2.40A GHz Prescott Socket 478 2x 256MB PC2100 DDR RAM, 2x 256MB PC133 SDRAM CoolMax 350W PSU DVD-ROM - will edit with brand & model 128MB ATi Radeon 9800 Pro AGP No hard drive So, I just put those parts together today and I tried to power it up, with the monitor connected to the Radeon 9800 in the AGP slot (mobo does not have VGA port). After turning it on, the CPU fan, graphics fan and system fan go on. However, the monitor remains in standby mode, despite being plugged in. Also, after pushing the button on the DVD-ROM drive, it does not open. I've used the DVD-ROM drive before with absolutely no issues. The graphics card was slightly buggy when I put it on another machine, which was left outside in winter weather for 3 months. (Still that computer's integrated graphics worked fine.) CMOS battery was replaced and jumpers are all set correctly. Now, I'm wondering whether the motherboard, CPU, PSU or GPU is the problem. What can I do to test which part is the problem? Just to clarify, I don't have a hard drive, so I usually boot Ubuntu from the disc drive. Anyways, thanks in advance!

  Read the article

• Xorg input devices fail without udev

  - by Sampo

  What I am trying to do: Launch Xorg server without udev device manager. What I have tried to do: Make sure that /dev/ has all required nodes, such as /dev/input/*. Make sure that all required kernel modules are loaded. Launch Xorg. What happens: Xorg starts up as excepted. Xorg loads correct GPU driver and sets right screen resolution. Xorg blocks all input devices (keyboard, mouse), Alt+F[1-12] does not work (can't go back to tty1). Unraw'ing keyboard to take its control from X removes blocking and after unraw I can Alt+F1 back to tty1. Xorg still does not handle any input. Why I think that it should work: Same configuration works well if udev is loaded. Loading udev does not add or modify /dev/ contents, all nodes stays same. My main question is: How to make Xorg input devices work without udev? Any additional information about how Xorg really uses/detects/grabs keyboard would be helpful. And any additional information about what udev really does (other than populating /dev/) would also be helpful.

  Read the article

• Nagios Check_hpjd giving me problems!

  - by Mister IT Guru

  When I run the following [root@host plugins]# ./check_hpjd -H printer1.mydomain.com : Timeout from host printer1.mydomain.com I have Net-snmp installed on my system, I noted that i didn't have net-snmp-utils installed, and then I was able to run [root@host plugins]# snmpwalk -Os -c public -v 1 printer1.mydomain.com system sysDescr.0 = STRING: HP ETHERNET MULTI-ENVIRONMENT sysObjectID.0 = OID: enterprises.11.2.3.9.1 sysUpTimeInstance = Timeticks: (325408663) 37 days, 15:54:46.63 sysContact.0 = STRING: sysName.0 = STRING: printer1 sysLocation.0 = STRING: sysServices.0 = INTEGER: 72 So I know that the printer is working as expected, (as far as SNMP is concerned). But when I run [root@host plugins]# ./check_hpjd -H printer1.mydomain.com -C public Error in packet () I get this error - From what I've tried so far, I know my host can communicate via SNMP, I know the printer responds via SNMP, so I guess I'm left to look at the plug-in, which I will be checking up on. I'm new to SNMP, I am investigating this with my good friend Google search, but I am on a learning curve here, so please forgive my questions if they sound stupid,

  Read the article

• Tooltips shadow stuck on desktop

  - by faulty

  I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. Turn of aero Hibernate Switch main display to external display and switch back. Change resolution Edit(heavyd): Here is a screenshot from my machine.

  Read the article

• Screen Flickering: Hardware or Software?

  - by Wesley

  I have a Samsung N120 netbook (upgraded to 2GB DDR2 RAM) and there has been a screen flickering issue for some time now. However, I have not been able to accurately determine whether it is a software or hardware issue. Here are some of the symptoms: The flicker is white-colored and shows up as vertical lines. Flickering or not, there may be occasionally some random blue patterns (no image distortion) The screen tends to flicker more when the screen is not tilted back all the way. When tilting the screen back and forth, the screen will usually flicker. Some images on the screen may randomly distort without full-on flickering. The screen will flicker only on certain websites, but not on others. A certain part of a webpage may constantly be distorted randomly, even when scrolling. While flickering, the mouse will not move though I'm moving my finger along the touchpad. A connected external monitor does not have any problems. The flickering is completely random and does not seem to follow any CPU/GPU usage trends. Flickering usually gets worse when the screen brightness is turned higher. There will be flickering on battery and while plugged in. Search up "Samsung N120 - Screen Flickering" on YouTube for an idea of what the flickering looks like. However, there is no visible distortions and the flickering seems to stop when the screen has dimmed. Since the problems started, I tried formatting and using Windows 7, then formatted again and went back to Windows XP. The screen was also replaced sometime during this past summer. The uninstallation of the Samsung Battery Manager (on the original install of XP) seemed to reduce the flicker partially, but eventually got worse. So, what could possibly be the problem?

  Read the article

• nVidia Driver - Laptop is forced as one of my monitors

  - by vaccano

  I am trying to get my nVidia Driver to correctly configure my multi-monitor setup. I have my laptop in a docking station and two monitors hooked up to it. I had an old driver that this worked correctly with. However, that driver was causing a lot of "Deferred Procedure Calls" so I upgraded to a newer driver. But now I am forced to use my Laptop monitor as one of my monitors. Here is the image in the nVida Control Panel: As you can see, both monitors are recognized, but the only options available are to use one of them with the Laptop Display. Any Ideas? I am running Windows XP (latest updates), I have an nVidia Quadro 1500M. I have tried several different driver versions and all the new ones have this issue.

  Read the article

• Modern monitor technologies - need to find a new monitor

  - by Michal Minicki

  I'm preparing to change my old LCD monitor for a new one. I have an old NEC 20WGX2 Pro based on an IPS panel. I'm looking for a screen that gives good color output but is very good at gaming at the same time (since it is its primary service). I tend to switch monitors between my different computers at home so it has to be multi purpose, hence IPS technology before. Now, where can I read on newest monitor technologies so I can make an informed decision? I need to find a best fit for myself and I have a very outdated knowledge at the moment. So any hints are greatly appreciated, be it info on technologies, web sources, links to other questions, etc.

  Read the article

• In what way does non-"full n-key rollover" hinder fast typists?

  - by Michael Kjörling

  Wikipedia claims (although the latter claim does not cite a source) that: High-end keyboards that provide full n-key rollover typically do so via a PS/2 interface as the USB mode most often used by operating systems has a maximum of only six keys plus modifiers that can be pressed at the same time.[4] This hinders fast typists, ... In what way would the system being able to recognize only six non-modifier keys at once hinder a fast typist? I consider myself a relatively fast typist and I usually press one key, plus modifiers, at once; I can't imagine any real-life situation in which the system only recognizing six non-modifier keys being pressed at once has been a limiting factor in my keyboard usage. (Multi-stroke keyboard shortcuts as used by high-end software like Visual Studio, Emacs and the like are a different matter.) Note that I am not really interested in answers centered around multiplayer computer games; I'm looking for answers that give reasons that would be relevant to typists, somehow supporting the statement made on Wikipedia.

  Read the article

• Should I Use PHP as FastCGI?

  - by Synetech inc.

  Hi, I am running an Apache webserver on my Windows machine. It is not generally a public server (most of the little bit of traffic comes from the machine itself, and most of the public traffic comes from crawlers). Basically, it is mostly just for use as a test-bed, development system. I have read about how running PHP as FastCGI is better (ie faster and more stable) than as an Apache module. However, I really don’t like the idea of multiple PHP.exe processes (I don’t like that Apache has two processes and I’m not even too thrilled with Chromium’s multi-process model). So I’m wondering if it would be worthwhile to change PHP to FastCGI for this scenario. If it is, how would I configure it? Pretty much all of the information I have seen has been either for non-Windows or for IIS. As I said, I’m running Windows+Apache. Thanks a lot.

  Read the article

• Why do my download speeds drastically vary during a download?

  - by J. Anthony Carter

  I watch the download speed rise and fall like waves in a storm. At night, during low bandwidth usage I have achieve speeds as high as 3.23 M/sec but the watch them decline to 250 K/sec. and then climb back up. Over and over. During the day my best is around 1.67 M/sec with lows into the 65 K/sec. On top of this, why does a download need to slow down when approaching the end of the download? It's not like a multi-hundred ton train needing to decrease speed as it approaches the station.

  Read the article

• Linux: How to break a large file into smaller files?

  - by Runcible

  I have a giant file (20 gigs) sitting on my source machine and I need to transfer it to my target machine. For the purposes of this question, let's assume that I do not have network connectivity between the two machines. I need to break this file into a series of smaller files, write the smaller files to DVD(s), then re-assemble everything on the target machine. Both source and destination machines are Linux boxes. Is there a way to accomplish this using tar? I have a feeling that I need to use the --multi-volume parameter. What are my options? I need to be able to specify the size of the volume files, in order to make sure that each one will fit onto a single DVD. Thanks!

  Read the article

• small light laptop with docking station that has a PCI(e) slot

  - by laramichaels

  Hi everyone, I am looking for a new laptop/netbook and I have two simple requirements: must be small (10-12in screen) and light (<=3-3.5pounds); must work with a dock into which I can put a PCI or PCI Express card. Basically, I have no performance requirements. Discontinued or low-end are fine. All I want is something easy to carry that when at work I can use a PCI/PCI Express card with to do multi-head. Eg, if an Acer Aspire 1410 fitted the second requirement I would by one in a blink. The only solution with which I am acquainted are Thinkpads that can go into the Thinkpad Advanced Dock. Do other laptop (or netbook brands) also offer the possibility of using Although this is not a "requirement" per se, I would rather hear about options that would not involve buying the latest-greatest-+$2k model... : ) Thank you for any advice! ~lara

  Read the article

• Problems with merge replication

  - by jess

  Hi, We are developing a multi-user desktop application with users located in different countries. The platform is - .net 3.5, SQL Server 2008, WinForms. Now, my client has used the help of a DBA who has implemented merge replication. To facilitate replication, we made all our primary keys as GUID. Now, we are facing these issues with replication - subscribers expiration sometimes stops replication and we have found no clean way to re-add every change to db schema requires to poll the whole data all over again! This seems to be strange, what could be the problem here? Also, sometimes we have duplicate keys, and that too stops replication I am sure these issues can be resolved. Maybe, we have not gone the right way to implement. Can you suggest how to go about implementing. Or, is the above information enough to diagnose the problem?

  Read the article

• Getting Dell E6320 with I7 to work with 3 monitors at 1920x1080p x 3

  - by MadBoy

  I want to buy Dell E6320 which comes with Intel Core I7-2620M (2.70GHz, 4MB cache, Dual Core) with Intel HD Graphics 3000. Laptop will come with docking station. I want to connect 3 monitors to that docking station so that working at home would give me some additional boost. Docking station will allow me to connect only 2 monitors so I'm looking at following other options: Matrox TRIPLEHEAD2GO DIGITAL Edition or TRIPLEHEAD2GO DP Edition. But reading Matrox Support Page intel GPU can't run the highest resolution with 3 monitors connected, it even gets worse since it seems monitors would have to be able to work at 50hz. Also I'm not sure but it seems that Matrox doesn't split the monitors as 3 separate monitors but simply as one big space (which is a bit opposite to what I need) Buy 2 or maybe just 1 USB based monitor but it would also mean having 1 or 2 different monitors then the main one, unless I buy 3 USB based monitors which would mean more money to spend. Also I found only couple of models and most of them require USB 3.0 and no other cables to plug in (nice but costly - couldn't find decent monitor with only USB for sending signal and having power connected normally) . But docking station has only one USB 3.0 port. Can I use hub and still get it to work? Find some converters from Digital to USB (I think DisplayLink does some?) Buy different laptop but what kind? I need it to be I7, small (13"), fast and lightweight. At same time it requires docking station that I can use at home to connect 3 external monitors. Some other suggested solution... Edit: I need 3 monitors for work in terms of coding in Visual Studio or having word/excel/outlook open. Nothing fancy. Maybe some movie once in a while.

  Read the article

• Computer freezes for 2+ seconds, mouse still moves

  - by xsaero00

  I have this problem on my workstation. The computer would effectively freeze for 2-5 seconds for no apparent reason, then continue as normal. While frozen the mouse would still be movable, but only on one of screens in my multi-screen setup. What can be the likely cause. System: CPU: i7-920 Memory: 12G of Patriot DDR3, 6 modules OS: SLED 11, Suse Linux Enterprise Desktop, using Gnome Main board: Asus P6T Video: two Nvidia 9500GT connected to three displays I am using memory at recommended settings of 8-8-8-1333. It has an XMP profile. Th CPU is a bit overclocked to 3.3 GHz, but my cooling more than allows for it. I ran the computer with all overclocks off and lower memory speed but the issue was still there. Any ideas? Where should I start looking?

  Read the article

• Triple Boot - With storage partition

  - by art

  I'm new to the multi-boot world, as i used to rely on virtualizing for running linux. Recently i moved to Dual booting Windows 7 and Ubuntu, with a storage partition for all my files where both operating systems could access them. Is it possible, to have 1 partition for 7, another for XP, another for Ubuntu, and a separate partition where the OS's can access my files? so 4 partitions on my hdd. and if there's a better way to go about this (or if its not possible), please let me know! thanks

  Read the article

• Samsung laptop randomly shuts down

  - by Dmatig

  I've rewritten this question because it turned into an indecipherable mess. I have a Samsung R560 laptop that is overheating, and shutting itself down under load consistantly. Thank you quickcel for reccomending me Speedfan to monitor my temps. Here they are (Load / Idle): (Ignore "Temp1 and Temp2", whatever sensors they are they'd always random, pretty sure they're broke). The load temperature is after just 5 minites of playing Fallout 3 - another 5 minutes and it (the GPU - 9600M GS) consistantly breaches the mid 90's then shuts down, so it's hard to get a good picture of it. I'm looking for some solution or way to decrease these temperatures, because they seem far too high even idle. I've tried: Opening up the case and clearing of all dust with compressed air. Updating drivers for my Graphics card Have purchased and am using a notebook cooler I don't want to: Undervolt / underclock (defeats the point of having a more expensive card) Use lower power / performance settings (again, i might as well have bought something cheaper) Is there anything else i can try (software or inexpensive hardware) that can help me fix this? Has anybody had a Samsung laptop and knows if this can be sorted under my warranty, and the turnaround time of sending it off (UK?)(it has always ran hotter than it should, but now at 6 months old is getting hot enough to power off)

  Read the article

• '0' inserted when cross-referencing numbered equations in MSWord 2007

  - by Jyotirmoy Bhattacharya

  I am inserting numbered equations using tables and multi-level lists as described in http://blogs.msdn.com/b/microsoft_office_word/archive/2006/10/20/equation-numbering.aspx I want to cross-reference the equations in my text. To do so I go to Insert-Cross reference and among the "Numbered Items" I pick the equation I wish to refer to. The problem is that if I pick the "Insert reference to" as "Paragraph number" a zero is always inserted into my text. The surprising thing is that the hyperlink in the cross-reference points to the correct equation. Also if I choose "Insert reference to" as "Page number" then the correct page numbers are inserted and they are correctly updated too.

  Read the article

• DBD::mysql gives mysql_init not found

  - by highBandWidth

  I have to install a non-admin copy of mysql and perl module DBD::mysql in my home directory. I installed mysql in ~/software/db/mysql and this works since I can start and stop the server and go to the mysql prompt. Then, I downloaded the perl module and installed it using perl Makefile.PL PREFIX=~/myperl/ LIB=~/myperl/lib/lib64/perl5/ --mysql_config=/my_home/software/db/mysql/bin/mysql_config --libs=/myhome/software/db/mysql/lib/libmysqlclient.a make make install I did this to use the statically linked mysql client library. perl -MDBD::mysql -e 1 gives no errors. However, when I actually try to use the module, I get /usr/bin/perl: symbol lookup error: /myhome/myperl/lib/lib64/perl5/x86_64-linux-thread-multi/auto/DBD/mysql/mysql.so: undefined symbol: mysql_init

  Read the article

< Previous Page | 132 133 134 135 136 137 138 139 140 141 142 143  | Next Page >