Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 143/314 | < Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >

• Connect a 2.5" (laptop hard disk) SATA hard disk to Desktop PC

  - by Lawliet

  Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) I bought a all-in-one Modex-to-SATA power adapter and SATA cable and I still don't know what to do. I have read various forums and a lot of people are stating that it's perfectly ok, but some are scaring me that by connecting it so, it fried their hard disk. And some also mentioned cutting the yellow 12V wire if I'm planning to use Modex-to-SATA power. Thanks in advance

  Read the article

• Forward a port with modem (with built-in but disabled router) + a separate router

  - by Youn

  I have a Motorola SBG6580 that is a modem and a wireless router in one. However, the wireless router part was bad so I disabled it and got a separate wireless router. I can go into the configuration pages of both the modem and the router now, and I'm confused as to which device needs to be configured for port-forwarding. I have a raspberry pi that I want to set up as a webserver. Do I configure the router, the modem, or both? Right now, the SBG6580's 1st LAN is connected to the wireless router's WAN, and the internet is working well. Note that the SBG6580 only has 4 ports, and I'm assuming they're LAN,as they are not labeled.

  Read the article

• Firewall software that can block access to certain applications on certain internet connections

  - by webmasters

  I have two internet connections, a LAN and a 3G modem on a Windows 7 machine. The LAN is connected to a Edimax router which is conneted to the ISP (with their own modem). Now, the Edimax router is set to auto assign IP adresses in the range: 168.192.2.100 and 192.168.2.200 I wanted to block internet explorer to access the LAN. I entered my AVG firewall, selected iexplorer and added a "block" rule which blocked all ports, TCP and UDP protocols for the above IP range. The problem is it did not work, not matter what rules I have tried. Can you recommend a firewall that can easily accomplish this? Ty

  Read the article

• How do you change your Airport or Ethernet MAC address in Mac OS X 10.6?

  - by Dave Gallagher

  I have a MacBook Pro and would like to set a custom MAC address for either my Airport WiFi card, or Ethernet port. In older versions of Mac OS X, you could do it like this: $ sudo ifconfig en0 ether 00:11:22:33:44:55 // Ethernet $ sudo ifconfig en1 lladdr AA:BB:CC:DD:EE:FF // Airport For it to work on Airport, you'd have to power it on (e.g. $ sudo ifconfig en1 up), ensure it's not connected to any wireless network, and execute the command. I'm aware such a change won't propagate across reboots. Unfortunately, this doesn't work on Mac OS X 10.6.6 anymore. Apple appears to have removed the functionality (the command fails silently). Does anyone have any idea how to do it? Thanks for any help you can offer! :)

  Read the article

• Monitor HTTP usage on network from Linux free

  - by David

  I manage a small office network. I am looking to start monitoring/logging internet usage (website requests) for each user on a small network. All the windows clients are running through a switch to a BT router. I also have a linux (centos) machine which is connected as a client to the BT router as well. Is there any free software I can install on the linux box (or my own machine) to allow me to log and monitor websites requested by users kind of like browser history. Ideally, something that would collect each client's browser history in 1 place. Thanks

  Read the article

• Encryption of OS X to Windows SMB traffic and password

  - by Brian

  I connected to a Windows Server 2008 R2 shared folder from a Mac OS X Mountain Lion computer over the Internet using this command: mount -t smbfs //user@server/path/to/share local_folder Is traffic encrypted by default? What settings do I look at (if any) to know whether it was encrypted? If it wasn't encrypted, what's the easiest way to encrypt it? Was the password I typed at the command line encrypted? Update: sysadmin1138 has addressed the password question. Does anyone know how I can tell if the traffic itself is being encrypted?

  Read the article

• change ip address verizon fios [closed]

  - by John Smith

  One well documented way to change a dynamically assigned ip address is to log into the router configuration settings and change the mac address , disconnect the router and modem, and to turn it all back on. This actually worked with a basic modem connected by ethernet directly to a laptop, spoofing laptop mac address, with a cable internet provider. Now this question is specific to fiber optic internet providers who bundle with tv and internet (verizon fios, comcast xfinity). Verizon fios installation comes with an actiontec router, and there is a built in way to clone the mac address in the router configuration settings. What will happen if the mac address changes from what verizon installed it as? Will they get angry and disconnect service? Will other services other than internet stop working (tv or phone)?

  Read the article

• Web Deploy to IIS7 fails with 401 (Unauthorized)

  - by Trex

  we have IIS7 running on Windows Web Server 2008 R2 and it's set up to support Web Deploy. It worked fine when we used the default Administrator account. We recently disabled this account (for security reasons) and are now trying to deploy using another account which is member of the Administrators group, but the deploy fails with 401 (Unauthorized). More specifically, it says: Connected to '<IP>' using Web Deployment Agent Service, but could not authorize. Make sure you are an admin on '<IP>'. The remote server returned an error: (401) Unauthorized. Anybody has any ideas why this is happening? Thanks. Trex

  Read the article

• Cisco asa 5505 locks up / unresponsive

  - by Chris

  We have a cisco asa 5505 that's new (in service for about 2 months) running 7.2(4) software. Every day around 10a it locks up for approx 10 minutes. We're monitoring it via snmp with stg, and snmp doesn't respond during that time. There's no output in the 'show crash' output. Internet connectivity is also dropped. Wondering if anyone else has seen this and what the fix might be. Currently we're looking at upgrading software, but will need memory upgrade for that. We've forced the speed and duplex on the internal and external interfaces, but the problem is still occurring. It's connected on the internal lan to a netgear 724 gige switch.

  Read the article

• Remote Desktop settings not being applied for user

  - by Anthony K

  We have a number of Win 2003 servers for which we have Remote Desktop enabled. Each user has their profile edited so that they can only connect for 2 hours maximum and have 30 minutes idle time, after which they are disconnected and the session closed. On one server however, the administrator account does not have the maximum session limit working. We can stay connected for days if we want. Originally this was how it was setup, and we later changed the profile for all users so that there are limits. We have rebooted the server a couple of times since, and the Management Console shows the limits. If we are idle for too long we are disconnected. Other users are having all the limits observed. Any suggestions?

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• ffserver - streaming problem transcodation for input

  - by zozo

  Good day to all. I have a little problem. I'm trying to stream something from a cam to a server and then forward to... somewhere (it will be a site or something). On the computer that I have the cam connected to I use vlc to stream it to the server and there I try to get the stream as an input for a ffserver. The problem is that ffserver doesn't detect the input (regardless of the protocol I use (udp, rtp, etc.)). I suspect a transcoding problem or something like that but I can't find any documentation about that so... Does any1 know what transcodation I should use? Thank you for help and have a great day.

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• Is it possible to shutdown a remote computer running Windows 7 via Telnet?

  - by Ryan Shripat

  I've successfully connected to my Windows 7 desktop over wifi via Telnet from an XP Home netbook. To login, I use the following command: telnet -l "win7desktop\win7user" win7desktop win7user in this case is an Administrator on win7desktop and is also a member of the Telnet Clients Group. The problem I have is that when I attempt to shut down win7desktop by issuing the following command: shutdown /s ...at the Telnet prompt, I get an Access Denied error: Access is denied.(5) Is it possible to shutdown a remote computer running Windows 7 via Telnet? If so, what do I need to do to get around the Access is denied error?

  Read the article

• Why would the boot screen be displayed on the external monitor?

  - by hegearon

  Why would the boot screen be displayed on the external monitor? This is not really a problem, I'd just like to know the reason behind this. If I boot without an external monitor both the BIOS settings and the boot screen are displayed on the built-in LCD monitor. However, when I boot with a monitor attached, the boot screen and the BIOS settings are displayed on the external monitor. There isn't any setting available regarding this in the BIOS setup (as opposed to my Thinkpad T42 where there is an option regarding this). System specification ASUS K53SV laptop DELL IN2030M monitor (connected via VGA) Windows 7 Enterprise SP1 64bit

  Read the article

• Static Routes and the Routing Table

  - by TheD

  This is very much a learning question if someone would be happy to explain a couple of concepts. My question is - the default routing table that exists in, in my case, a default Windows 7 install, what do each of the routes in the table do? Here is a screenshot: The 10.128.4.0 is just a route I've added while messing. I understand from a question I posted on Superuser the first route is just a default route that will route all traffic for any IP to my default gateway on my Interface in use. But what about the others? And how would the routing table handle a machine with multiple NIC's, perhaps connected to two different networks, or maybe even two NIC's on the same network so a VM can have a physical Network card instead of each VM sharing the hosts. Thanks!

  Read the article

• Reputable web based ssh client? [closed]

  - by Doug T.

  I'm connected to a coffee shop's wireless network right now, and I suspected I'd be able to use my laptop and ssh somewhere. Unlucky me they seem to be blocking everything but web traffic (my testing seems to show everything but port 80 is working, can't ping, ftp, etc). I googled "web based ssh clients" however I have reservations about entering my login credentials on any Joe Schmoe's web app. I was wondering if anyone has had any experience with any reputable web based ssh clients? If so could you please point me at one that I could trust?

  Read the article

• Does using a single cable to connect two switches create a bottleneck?

  - by Nick

  I realise this may be a stupid question for some, but it's something I've always wondered about. Let's say we have two gigabit switches and all of the devices on the network are also gigabit. If 10 computers connected to switch A need to transfer large amounts of data to a server on Switch B (at the same time), is the maximum transfer speed of each connection limited by the bandwidth of the connection between the two switches? In other words, would each computer only be able to transfer at a speed of one gigabit divided by the 10 machines trying to use the "bridge" between switches? If so, are there any workarounds so that every device can use it's maximum speed from point to point?

  Read the article

• Graphics card failure, anything I could try...

  - by ILMV

  My gaming PC has decided to die, it's not the first time but usually a quick ATX reset brings it back to life. Today it didn't. I disconnect all unessasary devices so I've only got the case button / LED cables, GPU, CPU, RAM and power connected, the computer still didn't turn on. I've not got a speaker on my motherboard so found a spare one I have for testing and when the machine starts up I get one long beep and two short beeps from my Award BIOS, which apparently means a video card error. I change it with the GPU from another machine and all works well. Q: So I have a faulty graphics card (an nVidia 8800GT OC), is there anything I can try to resurect it?

  Read the article

• VPN Server Problem

  - by vikas-2007bajaj

  Hi, I have Configure VPN Server for Online share Trading. I have so many VPN Clients in my VPN Server. Sometimes my VPN Clients disconnected from Systems but it shows in system tray i.e. connected but we are not able to access my application on the server.Then I disabled my Local area connection on client machine but it doesn't effect until I restart my System again.Firstly I want to know Task Manager Service for my VPN Client & how this problem can be remove.Waiting for reply. Thanks, Vikas Bajaj

  Read the article

• s3fs: how to force remount on errors?

  - by Alexander Gladysh

  I use s3fs 1.33 on Ubuntu 9.10. Regularily it gives me errors like this: rsync: writefd_unbuffered failed to write 4 bytes to socket [sender]: Broken pipe (32) rsync: close failed on "/mnt/s3/mybucket/filename": Software caused connection abort (103) rsync error: error in file IO (code 11) at receiver.c(731) [receiver=3.0.6] rsync: connection unexpectedly closed (86 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(600) [sender=3.0.6] Any attempt to work with mounted directory after that gives this error: Transport endpoint is not connected To get rid of this, I have to remount. Is there a way to force a remount automatically?

  Read the article

• MIDI Over Networking on OSX: Lots of beachballing

  - by Yar

  I have 4 computers connected to a Wifi router (with no Internet uplink). Whenever we enter the Network interface for Audio/Midi preferences in ANY of the computers, the Mac beachballs and then finally finds its way. Occasionally, however, one of the computers fails to receive the MIDI information that was destined for it via the Network MIDI interface. Changing to all wired connections does NOT help. Adding Internet uplink DOES help and the problem is resolved. This makes no sense to me as the computers can access each other just fine with or without the Internet uplink. Any ideas? [NOTE: I'll update the question if people correct my terminology, or feel free to do that if you have the rights].

  Read the article

• SQL Server 2005 Agent running SSIS job can't find file path

  - by alimack

  Basically I'm trying to run a functioning SSIS job (created in BIDS) under the SQL Server Agent - it reads a set of Excel spreadsheets and dumps the results into a table. The problem I'm having is getting the SSA to read the file path, the relevant part of the error is: "0x80004005 Description: "'N:\Assets Property & Facilities Management\Monthly Absence.xls' is not a valid path. Make sure that the path name is spelled correctly and that you are connected to the server on which the file resides." I've tried using UNC paths (\servername\ share) but the BIDS rewrites the paths to standard file paths (c:\directory\filename), I've also tried a proxy which runs this step under an Admin account. I've also tried changing the path to UNC on the SSIS job on the server. Also I'm forcing it to use the 32 bit DTEXEC, so it's not that either Always get the same error, do I need to re-create the job from scratch?

  Read the article

• Windows 7 USB power lose after a few seconds / minutes

  - by Stefan Dunn

  My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

  Read the article

• how can make transparent proxy on more than one port?

  - by ermya

  i want to make transparent proxy with linux ( centos) , i want all incoming connection on port 1000 - 2000 on eth0 forward to eth1 on port 1000 - 2000 in transparent mode i have 2 server 1- linux ( proxy server) 2- windows i want protect my windows server with my linux server firewall also i must make transparent proxy with my linux server linux server have 2 interface one for public network an another for private network connected to windows server so all incoming connection must connect to the linux server (at eth0 public network) first and after checking , must forward to the windows server on private network (with linux interface eth1 ) i can use squid for making transparent proxy but i dont know how i must config the squid for multi port because i want listen in more than 1000 ports for example from port 1000 to 2000 anyone know how can i do ?

  Read the article

< Previous Page | 139 140 141 142 143 144 145 146 147 148 149 150  | Next Page >