Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 148/391 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• configuring two network interfaces in ubuntu 10.04.1

  - by Bill Smith

  I have got two NICs configured on a VM - each is tied to a specific network, one is a DMZ, the other is an internal network. I want MySQL to listen on the internal network only and Apache on the DMZ listening for HTTP and HTTPS. But as soon as I add the second interface I run into trouble. I can hit HTTP on either interface, but can not hit 3306 on the internal network for MySQL. Here's the config... could someone sanity check this please? auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.153.24.230 netmask 255.255.255.240 network 10.153.24.224 broadcast 10.153.24.239 dns-nameservers 8.8.8.8 auto eth1 iface eth1 inet static address 10.153.24.195 netmask 255.255.255.224 gateway 10.153.24.193 broadcast 10.153.23.223

  Read the article

• Setup LAN to serve webpages and voip and access to the web site from inside LAN with domain name

  - by Mauricio Arias

  I'd like to know if it will work: I have my domain and I´m serving a webpage in a nginx to the internet, but if I type my domain in my laptop inside LAN I access to my modem/router configuration, I cannot access to the web server unless I type the IP address. I would like to add a Bind server after the modem/router - (port forward, ports 80 and 5060), if the request is www.mydomain.com bind should resolve the nginx IP address and serve it, and if it is a voip request should address to the voip server and if I'd like to access to the website from inside LAN I'd like to type mydomain.com. Could I do it with this configuration? Do I need something else? Thanks in advace!

  Read the article

• Configuring VLAN's on two HP procurve switches

  - by pan

  Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this ISP is coming through my internal network, I plan on using a new vlan called "airspeed" only for this ISP traffic. Up until now I've just been using the Default_vlan on both HP switches (4108 + 2524). So far I've been unable to ping from my laptop to the ISP modem both of which are on the new vlan 2 ("Airspeed"). No traffic needs to cross from vlan 2 to vlan 1 so I've left the ports as untagged. I've used the subnet provide from my ISP as the new vlan 2 subnet. Can anybody see what I'm doing wrong here? I've added the configuration of both switch below. Rough diagram: Microwave modem (Gateway IP 77.75.00.49) | HP 2524 switch (port 24) | HP 2524 switch fibre link | HP 4108GL switch fibre link | HP 4108GL switch (port D1) | Laptop configured with IP 77.75.00.50 (for testing but will be connected to firewall) And my 4108GL config: ; J4865A Configuration Editor; Created on release #G.07.21 hostname "HP ProCurve Switch 4108GL" cdp run module 1 type J4864A module 2 type J4862B module 3 type J4862B module 4 type J4862B ip default-gateway 128.1.146.50 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged A1-A3,B1-B24,C1-C24,D2-D24 ip address 128.1.146.203 255.255.0.0 no untagged D1 exit vlan 2 name "Airspeed" untagged D1 ip address 77.75.00.51 255.255.255.248 exit Finally my 2524 config: ; J4813A Configuration Editor; Created on release #F.04.08 hostname "HP ProCurve Switch 2524" cdp run ip default-gateway 0.0.0.0 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.51 "public" snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged 1-23,25-26 no untagged 24 ip address 128.1.146.204 255.255.0.0 exit vlan 2 name "Airspeed" untagged 24 ip address 77.75.00.51 255.255.255.248 exit no aaa port-access authenticator active

  Read the article

• connect two ESX hosts on private LAN

  - by maruti

  can a PC setup as W2K3 DC manage two ESX hosts connected to physical hub/switch? Services: DNS, DHCP, Domain distributed to host using a hub/switch. NIC2 on each host connected to switch/hub...spanning a virtual network inside each ESX host

  Read the article

• Multi-Boot through IPMI possible?

  - by yoursort

  Hi, I want to setup a cluster. On each machine Windows XP and Linux should be installed and the OS should be selectable by a boat loader (e.g. grub). All machines have IPMI cards. Is it possible when starting the machines over IPMI to also select the OS to boot? And how? Thanks!

  Read the article

• iSCSI connection timing out on ESX 3.5 against a NetApp storage appliance

  - by Jesse1973

  I get a timeout on iSCSI on different ESX hosts (3.5) at different times. It is puzzling, as both the ESX hosts as windows and other guests are experiencing timeouts. The iSCSI network is segregated on a private network. Here is an export of vmkiscsid.log from last night: 2010-02-10-12:30:38: iscsid: an InitiatorAlias= is required, but was not found in /etc/vmware/vmkiscsid/initiatorname.iscsi 2010-02-10-12:30:38: iscsid: LogLevel = 0 2010-02-10-12:30:38: iscsid: LogSync = 0 2010-02-10-12:30:42: iscsid: Login Success: iqn.1992-08.com.netapp:sn.101197719,default,192.168.73.2,3260,2001, 0x1 2010-02-10-12:30:42: iscsid: connection1:0 is operational now 2010-02-16-02:03:35: iscsid: Kernel reported iSCSI connection 1:0 error (1008) state (3) 2010-02-16-02:03:39: iscsid: connection1:0 is operational after recovery (2 attempts) 2010-02-16-04:02:27: iscsid: Kernel reported iSCSI connection 1:0 error (1008) state (3) 2010-02-16-04:02:32: iscsid: connection1:0 is operational after recovery (2 attempts) Should i edit the timeout value on the ESX host for iSCSI? This may work around the problem but will not solve it.

  Read the article

• How to install Archlinux on a acer emachines em350 ?

  - by zillion

  Do a 64 bits version will work better if the cpu is 64 bits capable ? Can I remove all added stuffs on Archbang or CTKArchLive to return to plain Archlinux with openbox that I can configure myself easily, so I can install Archlinux faster ? I tried and installed Arch properly but I need to install the broadcom bcm 4727 driver (b43,wl,sta,open source), which driver do I need and how can I install it by my usb on Archlinux CLI made with base, sudo and wireless_tools only ?

  Read the article

• Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

  - by Nick G

  I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

  Read the article

• Changing subnet-mask of class-c network host to 255.255.0.0

  - by Prashant Mandhare

  We have a existing class-c network with IP address range 11.22.33.44/24 (just for example). My domain controller has been configured within this subnet. So all servers within this subnet have subnet mask configured to 255.255.255.0. Now we have got a new subnet with IP address 11.22.88.99/24 (note that only last 2 octets have changed). I want all new hosts in this new subnet to join my existing DC. For this we have configured firewall properly so allow this. (so there is no issue with firewall). But initially I was not able to join hosts in new subnet in existing domain. Later I doubted on subnet mask used in domain controller (255.255.255.0) and for testing purpose I changed it to 255.255.0.0, it worked like charm, i was able to join subnet-2 hosts in subnet-1 domain. Now i am wondering whether it will be good practice to change subnet mask of a class-c network to 255.255.0.0? Can any issues arise due to this? Experts please provide your opinion.

  Read the article

• Check packet vlan tag using Tap virtual interface

  - by ankit

  Hi all, I am trying to learn how to implement virtual interfaces using the Tap driver. So far my understanding is that using the tap driver I can create a virtual interface and then have a userspace program attach to this interface to analyse the data coming into this device. Now what if I attach a cisco switch to my LAN interface using a TRUNK link, forward all the packets coming into the LAN interface to the virtual tap interface and then in my program attached to this interface do some coding to analyze the vlan tag in the packet and only allow certain vlans to be forwarded to the WAN interface ? Does this sound plausible or is there is flaw in my basic understanding ? Thanks for the help! ankit

  Read the article

• How can I set up multiple dynamic users to update a single network's dynamic IP

  - by d3vid

  On my home network we are allocated a dynamic IP. I want to configure ddclient (or an equivalent) to send IP updates to DNS-O-Matic/OpenDNS only when I am on my home network. I do not want to send IP updates when I'm on my office network. Can this be done? I am prepared to use different FLOSS software or a different free DNS service. Additionally, there are multiple users who may be on the home network or away on other networks. How can we configure ddclient on each machine so that whoever is on the home network updates the IP (i.e. so we don't have to rely on a particular machine being on the network to update the IP). OpenDNS support have said we can't simply install updater software on each machine.

  Read the article

• SQL instance through F5 BigIP VIP

  - by Sam

  We have a SQL 2008 instance Server01\instance02. The port is set to 1466. We've set up a VIP named Server1 Attempting to connect to Server1\instance02 does not work. Server1,1466 does work. We have ports 1433, 1434 and 1466 open. Can we configure this to be able to use the name without any changes to the SQL client. Thanks!!

  Read the article

• how to connect to wampserver from the other computer

  - by user28233

  I have two computers. with both windows 7 as os. One pc has wampserver installed how do I connect them so that the other one can access the database that is in the other pc. I have a hub that connects both physically but how do I set it up in the os?

  Read the article

• Setting up Windows 2008 with VPN and NAT

  - by Benson

  I have a Windows 2008 box set up with VPN, and that works quite well. NPS is used to validate the VPN clients, who are able to access the private address of the server, once connected. I can't for the life of me get NAT working for the VPN clients, though. I've added NAT as a routing protocol, and set the one on in the VPN address pool as private, and the other as public - but it still won't NAT connections when I add a route through the VPN server's IP on the client side (route add SomeInternetIp IpOfPrivateInterfaceOnServer). I know I can reach the server's private interface (which happens to be 10.2.2.1) with remote desktop client, so I can't think of any issues with the VPN.

  Read the article

• Cisco 837 not passing UDP traffic properly (was: DNS query problem)

  - by TessellatingHeckler

  We have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch - LAN. It has been fine for years, suddenly DNS resolution stopped working from the LAN to public DNS servers. No changes that I know of, so I can't revert anything. Current behaviour: DNS requests from the LAN using TCP show up in the oubound firewall log, in the Cisco debug log, in the dns-server-firewall, in tcpdump on the DNS server, the answer comes back, it works fine. DNS requests from the LAN using UDP show up in the outbound firewall log, in the Cisco debug log, but does NOT show in the dns-server-firewall, not in tcpdump on the DNS server, times out. DNS requests from the Cisco using UDP show up in the dns-server-firewall and in tcpdump on the DNS server, answer received, works fine. netcat connections to port 53 or a random port by TCP show up in the dns-server-firewall netcat connections to port 53 or a random port by UDP do not show up in the dns-server-firewall Summary: TCP seems fine throughought. UDP works from the Cisco over the ADSL, and it works from the LAN to the Cisco, but it doesn't seem to cross the Cisco 837 properly. Update: confirmed with netcat that any UDP traffic from the LAN is affected, not just traffic to port 53. Update: If I change the firewall's external IP to any other IP in the subnet, this starts working. When I put it back, it stops working. I now suspect it's an ISP issue (does that sound plausible?), and am removing the Cisco config.

  Read the article

• windows 7 no internet access

  - by Kyle

  Just did a fresh install of Windows 7, and the network and sharing center says no internet access. Disabling and enabling the adapter seems to fix the issue temporarily, but the internet stops working shortly after. I have installed the latest NIC drivers and have installed all Windows updates. I have also tried manually setting the ip/gateway/dns and running netsh int ip reset in an elevated command prompt. I am running Windows 7 Home Premium 64bit with a wired connection. I have searched for hours, but have found no working solutions. Does anyone have any ideas?

  Read the article

• Airport Extreme and Windows PC via regular LAN (not WIFI)

  - by Mr AJL

  So I got an airpoort extreme, and everything works beautifully on the mac, but my windows 7 PC which is connected via a regular ethernet cable can't see any network. The Win7 PC says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Thanks!

  Read the article

• iPod touch has extremely slow wifi, drops packets - only on my router

  - by mskfisher

  I just purchased an iPod Touch. I am having a lot of trouble with its speeds on my Tenda W311R, but it has no speed problems on my neighbor's Netgear router. It will connect and authenticate to my network, but the Speed Test app from speedtest.net shows rates near 20-50 kbps. If I run the speed test immediately after powering the iPod on, it will get speeds of 10-20 Mbps, like it should - but the speeds slow down to the kbps range abut 10-15 seconds afterward. I get the same behavior with encryption and without encryption, and regardless of N, G, or B compatibility settings in the router. I've tried rebooting the iPod and resetting the network settings, but it's still slow. I've tried pinging the iPod from another computer, and it shows about 40% packet loss: $ ping 192.168.0.111 PING 192.168.0.111 (192.168.0.111): 56 data bytes 64 bytes from 192.168.0.111: icmp_seq=0 ttl=64 time=14.188 ms 64 bytes from 192.168.0.111: icmp_seq=1 ttl=64 time=11.556 ms 64 bytes from 192.168.0.111: icmp_seq=2 ttl=64 time=5.675 ms 64 bytes from 192.168.0.111: icmp_seq=3 ttl=64 time=5.721 ms Request timeout for icmp_seq 4 64 bytes from 192.168.0.111: icmp_seq=5 ttl=64 time=6.491 ms Request timeout for icmp_seq 6 64 bytes from 192.168.0.111: icmp_seq=7 ttl=64 time=8.065 ms Request timeout for icmp_seq 8 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 64 bytes from 192.168.0.111: icmp_seq=11 ttl=64 time=9.605 ms Signal strength is good - I'm never more than 20 feet from my access point, and it exhibits the same behavior if I'm standing next to the router. It works just well enough to receive text, but videos don't work at all. App downloads are hit and miss. I've tweaked just about all of the settings I can see to tweak, and I'm at a loss. I have also been searching Google for the past three days, all to no avail. Any suggestions?

  Read the article

• VirtualBox guest responds to ping but all ports closed in nmap

  - by jeremyjjbrown

  I want to setup a test database on a vm for development purposes but I cannot connect to the server via the network. I've got Ubuntu 12.04vm installed on 12.04 host in Virtualbox 4.2.4 set to - Bridged network mode - Promiscuous Allow All When I try to ping the virtual guest from any network client I get the expected result. PING 192.168.1.209 (192.168.1.209) 56(84) bytes of data. 64 bytes from 192.168.1.209: icmp_req=1 ttl=64 time=0.427 ms ... Internet access inside the vm is normal But when I nmap it I get nothin! jeremy@bangkok:~$ nmap -sV -p 1-65535 192.168.1.209 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:39 CST Nmap scan report for jeremy (192.168.1.209) Host is up (0.0032s latency). All 65535 scanned ports on jeremy (192.168.1.209) are closed Service detection performed. Please report any incorrect results at http://nmap.org/submit/ Nmap done: 1 IP address (1 host up) scanned in 0.88 seconds ufw and iptables on VM... jeremy@jeremy:~$ sudo service ufw stop [sudo] password for jeremy: ufw stop/waiting jeremy@jeremy:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I have scanned around and have no reason to believe that my router is blocking internal ports. jeremy@bangkok:~$ nmap -v 192.168.1.2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-11-15 18:44 CST Initiating Ping Scan at 18:44 Scanning 192.168.1.2 [2 ports] Completed Ping Scan at 18:44, 0.00s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 18:44 Completed Parallel DNS resolution of 1 host. at 18:44, 0.03s elapsed Initiating Connect Scan at 18:44 Scanning 192.168.1.2 [1000 ports] Discovered open port 445/tcp on 192.168.1.2 Discovered open port 139/tcp on 192.168.1.2 Discovered open port 3306/tcp on 192.168.1.2 Discovered open port 80/tcp on 192.168.1.2 Discovered open port 111/tcp on 192.168.1.2 Discovered open port 53/tcp on 192.168.1.2 Discovered open port 5902/tcp on 192.168.1.2 Discovered open port 8090/tcp on 192.168.1.2 Discovered open port 6881/tcp on 192.168.1.2 Completed Connect Scan at 18:44, 0.02s elapsed (1000 total ports) Nmap scan report for 192.168.1.2 Host is up (0.0017s latency). Not shown: 991 closed ports PORT STATE SERVICE 53/tcp open domain 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 445/tcp open microsoft-ds 3306/tcp open mysql 5902/tcp open vnc-2 6881/tcp open bittorrent-tracker 8090/tcp open unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 0.08 seconds Answer... Turns out all of the ports were open to the network. I installed open ssh and confirmed it. Then I edited my db conf to listen to external IP's and all was well.

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• Permanently change IP address on SuSE 10

  - by Long Ngo

  I am trying to change IP address of a SuSE 10 machine that is running Tomcat. I need to create a shell script to do this so could not use YaST. As some sites suggested on my Google search, I edited the files in /etc/sysconfig/network/ifcfg-eth-* to change the IP address. After that, I restarted the network service by calling /etc/init.d/network restart. The network card restarting just fine. I, then, restarted tomcat web service. However, when I browsed the new IP address using browser, I got an "Request denied" message. Can anyone please tell me how I could do this? Thanks

  Read the article

• Unable to browse Server 2008R2 from XP clinets

  - by Dave M

  We have just deployed a Windows 2008R2 server in our Windows 2003 domain. XP clinets are unable to browse in "entire network" and find the new server. It can be accessed by entering \\servername and it can be pinged by name and IP address. Users access shares without issue. Netbios over TCP/IP is enabled. Computer browser is running on the Windows 2008R2 system. Turn on Network Discovery is enabled. These services were started as a result of an MS article Computer Browser DNS Client Function Discovery Resource Publication SSDP Discovery UPnP Device Hosts

  Read the article

• Best free (or cheap) ASP.NET based CMS for a club/association?

  - by marc_s

  I've been looking for a simple, intuitive ASP.NET based CMS to handle my club/association site. It should be based on ASP.NET so I can add some extra specific pages offer a membership system, e.g. I want to be able to define members which can e.g. comment posts, while anonymous users can only read (no active participation) have features like news, forums, blogs, picture gallery be simple and easy to use I've been looking at GraffitiCMS: so far my favorite, but it has no forum, and no membership system, and no future, it seems - no development whatsoever in over a year :-( Sitefinity: had extreme trouble even getting it installed, and when it's finally up and running, I find it overly complicated and not intuitive at all Umbraco: same problem - hard to install, hard to get up and running, the intro videos on their site are only available to paying subscribers (what's up with that deal???)..... DotNetNuke: seems like a major overkill Community Server: seems like a major overkill - and seems to be more and more commercial, only Any others I've missed that I should have definitely looked at ??

  Read the article

• HomeMade/DIY NAS solution

  - by MicTech

  Has anyone experience with building NAS (Network-attached storage) for home/small office using? What component would you recommend? Hardware CPU motherboard HDDs RAID controller etc. Software OS FTP HTTP etc.

  Read the article

• Clickonce applications being allowed through firewall

  - by DanielF

  The company I work for uses an application that is deployed through clickonce. This means that everytime they update said program the program regenerates in a new location ie: C:\Users\%username%\AppData\Local\Apps\2.0\89XCT43D.10T\WBZ8WE7L.927\trm8..tion_1ad39bb503bcb5df_0008.0005_14829906c9aa8611\%appname%.exe Recently the computers were updated to windows 7 machines and now everytime an update is pushed out the windows firewall see this as a new application and prompts the users to allow the program through the firewall. THis means I have to walk around to every computer and type in admin credentials. Does anyone know of a way to allow the application regardless of the path it is in? Google has not been very helpful so far.

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >