Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 158/370 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Kickstart: ifcfg-eth0 file genorated by kickstart when install from network but from initrd when install form USB

  - by dooffas

  When I install Fedora 19 with a kickstart file and via network, the generated ifcfg-eth0 file is genorated by the kickstart: # Generated by parse-kickstart However if I use the same kickstart file and install via a USB stick, the ifcfg file is generated by initrd. # Generated by dracut initrd The line in the kickstart file to set the network settings is as follows: network --device=eth0 --bootproto=dhcp --hostname=SOMEHOSTNAME Is there away to keep network device settings set in the kickstart file when not installing via network?

  Read the article

• How to create a separated network to customers only?

  - by Valter Henrique

  I work in a company where we have a network ethernet and wi-fi, we would like to create a network where our customers could access our network but don't have access to our computer network. This access would be internet only, nothing more. The customers will not see our computers and the files that we share in our network. I have two routers, how can I do this ? A Cisco Linksys Wireless-N Broadband Router WRT160N V3 and a Netgear Wireless G Router WGR614 v9 and about firewalls there´s only windows firewalls in each computer by default.

  Read the article

• Killing CLOSE_WAIT sockets without killing parent process on Linux

  - by Alex Neth

  Tomcat is leaving me with CLOSE_WAIT sockets which ultimately saturate the maximum number of connections. I've tried many methods in my client and server code to get rid of these to no avail, including closing connections, calling System.gc(), etc. Now I'm trying to find a way to simply time these out quickly in the OS. I've got conntrack working, but am not sure how to use that to kill these connections. I've also set /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_close_wait to 1, which of course is too low but the connections persist. Is there a way to kill these zombie sockets? Running Ubuntu.

  Read the article

• Why is my connection to Playstation Network so unreliable? [closed]

  - by jammus

  Hello friends. I'm 28 and my girlfriend is 24. Our home internet connection is pretty reliable, it's almost always up and can get fairly high download speeds. However, my experience with the Playstation Network is pretty frustrating. I'm always getting kicked off or getting quite high latency. Are there any tips or tricks that you might help my on-line gaming run more smoothly? I'm using a wireless connection for the PS3, is this likely to affect things?

  Read the article

• What is error 324? Is it related to Google Chrome? Or Verizon Webmail?

  - by Jason Rhodes

  My in-laws are having trouble with signing into their Verizon Webmail account at webmail.verizon.net, only when they are on their wireless network. When they try to log in from wireless they get "Error 324" in the browser, in both Google Chrome and Internet Explorer 8. But they can access any other site, and they can get on their Verizon email when they plug in directly to the browser. Why is this?

  Read the article

• Copying between 2 network devices

  - by Dave Rook

  My network has 3 devices - 1 PC and 2 other network devices (which could be PC, NAS, external hard drive etc) If I want to copy data from one network device to another network device from my PC (using the copy and paste method (i.e right click a file, select copy and then right click into the destination folder and click paste) and therefore not using any tools that could be built into the network devices for such a transaction), does the data get routed via my PC or use my systems resources?

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• TTL and traceroute showing different values for same domain

  - by Cray XT3

  y am i getting two different output for tracert and ping. Ping Result showing total hops of 20 and tracert showing 8. default ttl value on my linux machine 64,icmp echo reply ttl value 44. 64-44=20 but tracert is showing only 8 hops. What can be the reason? If tracert is implemented using ttl then why am i getting different values for same domain.no matter how many times i tried. Fo google and google services,ttl value and tracrt are same,but for other domains its different.

  Read the article

• Traceroute to IP address fails, but traceroute to domain name with same IP address is okay. Why?

  - by tomo

  When I traceroute to this IP (108.162.198.181) it stops after 1 hop. But tracerouting to a domain (www.gomodule.com) with the same IP shows 9 hops ending in that target. traceroute to www.gomodule.com (108.162.198.81), 64 hops max, 52 byte packets 1 192.168.1.1 (192.168.1.1) 131.667 ms 48.532 ms 48.837 ms 2 118.69.255.124 (118.69.255.124) 91.521 ms 79.177 ms 30.679 ms 3 42.117.11.225 (42.117.11.225) 30.270 ms 32.091 ms 29.698 ms 4 118.69.253.213 (118.69.253.213) 32.234 ms 118.69.253.237 (118.69.253.237) 70.667 ms 118.69.253.213 (118.69.253.213) 82.440 ms 5 118.69.253.245 (118.69.253.245) 64.554 ms 80.277 ms 130.224 ms 6 118.69.251.205 (118.69.251.205) 65.635 ms 118.69.249.78 (118.69.249.78) 133.234 ms 118.69.251.205 (118.69.251.205) 224.111 ms 7 118.69.251.249 (118.69.251.249) 156.679 ms 111.965 ms 64.165 ms 8 cloudflare1-rge.hkix.net (202.40.160.246) 64.102 ms 64.498 ms 74.581 ms 9 108.162.198.81 (108.162.198.81) 66.873 ms 67.426 ms 69.054 ms -vs- traceroute to 108.162.198.181 (108.162.198.181), 64 hops max, 52 byte packets 1 192.168.1.1 (192.168.1.1) 96.588 ms 3.003 ms 4.976 ms 2 118.69.255.124 (118.69.255.124) 45.223 ms 31.449 ms 31.225 ms 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * ...

  Read the article

• Standards for documenting/designing infrastructure

  - by Paul

  We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

  Read the article

• Why is network utilization so low

  - by dean20007

  My network utilization in windows never seems to get above 1%. This seems absolutely tiny, does anyone know why it is so low and if there is anyway to increase it(or if it indeed does need increased) FYI: I use a D-LINK USB wireless adaptor

  Read the article

• Windows XP does not list WPA wireless networks

  - by Tomalak

  What can be the reason that Windows XP does not show WPA-encrypted wireless networks? The laptop I have problems with is an older model (Toshiba Satellite Pro 6100) with Windows XP SP3 on it, fresh install. The wireless network card in it is an Agere product that lists as "Toshiba Wireless LAN Mini PCI Card". The networks showed up perfectly before I first tried to connect to one (it was set to WPA2). The connection failed (the card supports WPA only), then something must have happend and Windows hides these networks now. A manually configured WPA setup via Windows' own wizard works, I'm using it right now. The network just won't show up in the list of available network on its own. I suspect that XP incorrectly set a flag somewhere that this network card does not support WPA. Is there such a flag, and if so, how can I change it back?

  Read the article

• SCP command Clarification

  - by david.colais

  I'm using the scp commands to pull some files from the remote server and one variation of the command is not working. I have 2 files names one.xml and two.xml in a remote server and I'm pulling these two files into the current dir using the following command: scp [email protected]:/student/class/Intermediate/one.xml . scp [email protected]:/student/class/Intermediate/two.xml . The above command works fine but if I use wildcards to pull all the xml files in a single shot as shown below it returns scp: No match. scp [email protected]:/student/class/Intermediate/*.xml . Why is it working if I pull the files individually and not working if I try to pull using wildcards.

  Read the article

• Wireless Network Question?

  - by wifi

  Will the D-Link - Xtreme N Wireless-N Gigabit Router work with my AR5009 802.11 a/g/n WiFi Adapter?

  Read the article

• TCP video streaming: TCP throughput(rate) and RTT

  - by misteryes

  we know that a rough estimation of TCP rate is: WINDOW/RTT, where WINDOW is the min(CWIN, RWIN), CWIN is the congestion window size of the sender, while RWIN is the receiving window. nowadays, the encoding rate of videos may be 1000KB/s(8000kbit/s), if RTT is 500ms, it needs the window size to be 2000KB. But we know that usually the receiving window size is below 64KB, there is a big gap. so if RTT is too large, TCP streaming is not possible? Is my understanding right? thanks!

  Read the article

• Once VPN connection is done, how do I proceed reaching the other side address space?

  - by sports

  I'm using Windows Azure and I created a VPN Site To Site, configured like this: My virtual network: My address space: 10.2.0.0/16 (65531) Subnet1: 10.2.1.0/24 (251) Subnet2: 10.2.2.0/24 (251) Gateway: 10.2.3.0/29 (3) My public gateway IP: 137.135.x.z (I wont show x and z for security reasons) This public gateway uses, as you can see, 5 IPs on subnet1 and 5 IPs on subnet2, and 5 IPs on the gateway "Their" virtual network (in azure this would be a "Local network") Their address space: 172.60.100.67/32, 172.60.100.68/32, 172.60.100.69/32 Their device public IP: x.x.x.x (ommited for security reasons) Notice their address space are 3 IPs So: the VPN is "in green" (in Azure is showing up green, literally, like these two are connected) and now my question is: How do I proceed to reach their address space? I've tried creating a virtual machine (Windows Server 2008, but it could be an Ubuntu) on "my" virtual network and it is automatically "placed" on subnet1 or subnet2. So it gets the IP 10.2.1.0 (valid example), I can't choose to place the virtual machine in the gateway address space. How do I "reach" any of the IPs 172.60.100.67, 172.60.100.68, 172.60.100.69 ? In other words: How can I telnet any of these IPs? or ping? or see them in my network? Please provide me answers for Windows Server 2008 or for an Ubuntu. I'm open to create any virtual machine.

  Read the article

• Wireless bridge between two prolink adsl modem/router

  - by MyName

  Allright, so i've got 2 prolink hurricane h5004n. Its a broadband adsl modem and router. My Pc is connected to the first one via ethernet. What i want to do is a wireless bridge to make the 2 routers "talk". I've tried hooking up the dsl cable (as they are modems) in both to try but when one disconnects as the other connects. I don't really know about the configurations to be done of all the DCHP or RIP and NAT forwarding stuffs. (i'm just writing what i saw) In short i want the second router to act as a wifi repeater but i don't see any repeater option and i also do not want to connect them via ethernet. So is it possible to do something? Apart from buying another repeater i don't want to spend anymore i'm done :S

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• setting up my own name server

  - by mmokh

  I'm in the process of setting up my own name servers using BIND9, however I want to visualize the name server setup in relation to registrars and other name servers. Say I have a domain www.mydomain.com I setup my 2 name servers: ns1.mydomain.com - 192.168.0.1 ns2.mydomain.com - 192.168.0.2 1) How does the world know that my name servers are now at ns1.mydomain and ns2.mydomain. I read about setting up glue records at my registrar. Could you please elaborate on this, i.e. once i setup these glue records, can I now use my name servers in NS records for any other domain? For e.g. NS records for www.otherdomain.com - ns1.mydomain.com/ns2.mydomain.com 2) Given I setup the glue records as mentioned above, do I "have to" update mydomain.com NS records to point to my name servers? Can I keep mydomain.com NS records pointing to my registrars name servers, however use ns1.mydomain.com/ns2.mydomain.com as name servers for any other domain I own? Thanks

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• Mounting any Windows share from OS X 10.7.5 suddenly stopped working

  - by user2169619

  I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

  Read the article

• Conferences to go to 2011 Edition

  - by Zypher

  It's that time of year to start thinking about what conferences we want to beg,plead,borrow and steal to get to go to this year. We all like a good conference, but are generally limited in the funds available to go to them - if we are provided any - so we need to be at least a little picky. What are the conferences that you are really excited about this year, and what tracks do you think will be the most beneficial to a sysadmin?

  Read the article

• Windows 7 Automatically Connecting To Unsecured Wireless Networks On Startup

  - by Xtend

  Most of the questions on this topic related to folks connecting to somebody else's wireless network when their own was available and could remedy the situation by going to their connections and unchecking the "connect automatically" box. See this: " Avoid automatically connecting to wireless network on windows 7 " as an example. In my situation, I've noticed that Win 7 will automatically connect to any unsecured wifi network - even if I have never connected to it in the past. If I am traveling and boot Win 7, it will start and connect to what appears to be the best signaled unsecured network without prompting me for confirmation (note: in the above link, "Naveen" seems to have same problem). Obviously, that is a security concern to me. Further, when I open "Network and Sharing" and "Manage wireless networks" the network is not displayed (probably because I labelled it a public network). Again, these are new, never connected with before, wireless networks. I always promptly disconnect from them but don't want to have to be on constant guard for an auto connection to a malicious network. This began about a month ago, as I recall, Win 7 did not behave like this in the past, I didn't monkey with wifi settings, and don't use a 3rd party connection manager. I did have to download some internet security certificates for army website access but I don't think that should mess with network settings. Any ideas how I can tell Win7 cease automatically connecting to networks or, at least, to prompt me for a confirmation before connecting?

  Read the article

• Blocked connections passing through firewall. What is wrong?

  - by Kiranu

  In our company we have a small business router (Cisco RV082) on which we are using its standard configuration (block all incoming traffic). We also have an SMTP relay configured (using WS2008R2) so that our internal applications can send email through google apps (which requires authentication). The thing is that the server was being used to send spam. We fixed the problem by only allowing the server to relay email from our internal IP address range (10.0.0.0/16). My concern is that there was a way by which external IPs connected to the network and that underlying problem has not been fixed, but I cannot imagine how these machines connected. Any thoughts?

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >