Search Results

Search found 7845 results on 314 pages for 'connected'.

Page 159/314 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• something is downloading in background Linux

  - by wisdom

  My laptop boots normally to Linux -LinuxMint- and immediately I like to open gnome-system-monitor but the shock is that something is downloading(the problem has been out 2 days ago) and nothing I run yet ! I did iftop in terminal but nothing strange -a screen shot provided-, also I tried nethogs which showed nothing at all. The more complicated when I reboot and same problem is there so I can't browse/surf Internet, no one connected to my network can browse any more it's absorbing the stream horribly! After many reboots it will go to normal state(no background downloading). But really I can't figure out the problem going behind the scene ! Any suggestion,any help would be appreciated...thanks

  Read the article

• How to establish SIP connection, when SIP-proxy is required?

  - by LA_

  I have Asterisk/1.8.13.1 Asterisk GUI-version : SVN--r Yes, quite old one, but I can not update it since this is installed on my Synology NAS. NAS is connected to internet thru router Asus RT-N16. I should use the following data to connect to the server: Auth name – 7499952XXXX User name/User ID/Display Name – nickname Authorization user name - [email protected] Domain - sip.beeline.ru SIP proxy server - msk.sip.beeline.ru I've also found the following string: [email protected]:password:[email protected]@msk.sip.beeline.ru:5060/7499952XXXX I've tested the parameters on my PC thru X-Lite and it works well (so, assume there is no any problem with the router, no need to do anything with router's NAS settings). But since I am quite new to Asterisk, I can not understand where to input all these data. Asterisk GUI doesn't have fields for proxy: Can somebody please help me with step-by-step instruction? Thank you in advance!

  Read the article

• Monitor Bonded Interface for Disconnection

  - by bradlis7

  I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

  Read the article

• iPhone always assigned wrong ip

  - by Ashley Ray

  for some reason most of the time my iPhone connects to the home network the ip address seems wrongly assigned as it 'loses connection' even even with strong reception. If I change the ip address to a static from 168.2.10 to 168.2.15 works fine until it appears to renew back to the prior. I am using a power-plug extender from the modem to router. Then have a laptop Printer playstation tv and another iPhone that always connect fine. The modem also has a crappy wireless which I haven't connected any devices to. I'm sure the forum will have a simple answer!

  Read the article

• Detecting damage done by virus

  - by user38471

  This morning after I went to college, a virus infected my PC without any user interaction at my end. When I came home my computer was completely frozen and infected with lots of trojans. I have not typed anything important since returning so keys cannot be logged. However I want to know exactly when my computer crashed from the time of infection to see what could potentially be done remotely by a hacker. The virus my pc was diagnosed with was "fakespypro" on a fully updated Windows 7 installation with firewall enabled. My computer was connected to an internal dorm room network, so probably that has had to do something with it. Any further information about how I could backtrace this virus infection or ways to discover what data might be stolen would be greatly appreciated.

  Read the article

• Vmware Workstation Development Server on Laptop

  - by Koobz

  I'm running an Ubuntu guest OS on my Windows 7 laptop. Currently, I have it set up for bridged networking. The guest is os is configured for a static ip of 192.168.1.115, which depending on the network I'm connected to, may not be available. When I want to view my development work I hit that up in my web browser. I'm really looking for the following scenario: 1) My guest OS ip address stays constant. 2) I can access my guest os even if I don't have an internet connection, or a lan/router. 3) I can share files with my guest/host. How does one accomplish this using VMware Workstation?

  Read the article

• Bind dns server in Solaris 10 and win xp clients

  - by stevecomptech

  Hi, Added this in zone db file, i am running solaris 10 _ldap._tcp.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.mydomain.com. SRV 0 0 88 dc.mydomain.com. _ldap._tcp.dc._msdcs.mydomain.com. SRV 0 0 389 dc.mydomain.com. _kerberos._tcp.dc._msdcs.mydomain.com. SRV 0 0 88 host.mydomain.com. Now i get this error when i try to join win xp to the domain The query was for the SRV record for _ldap._tcp.dc._msdcs.mydomain.com The following domain controllers were identified by the query: host.mydomain.com Common causes of this error include: Host (A) records that map the name of the domain controller to its IP addresses are missing or contain incorrect addresses. Domain controllers registered in DNS are not connected to the network or are not running. What do i need to change in order my win xp join the domain

  Read the article

• Printer Brother DCP-110C Linux 64-bit drivers

  - by Ondra Žižka

  Hi, I need 64-bit Linux driver for DCP-110C (for Ubuntu 10.04 64-bit) I found only 32-bit here. http://welcome.solutions.brother.com/bsc/public_s/id/linux/en/index.html I've tried to follow those instructions. During the installation, I got this: ondra@ondra-doma:~/Downloads$ sudo dpkg -i --force-all dcp110clpr-1.0.2-1.i386.deb dpkg: warning: overriding problem because --force enabled: package architecture (i386) does not match system (amd64) (Reading database ... 257283 files and directories currently installed.) Preparing to replace dcp110clpr 1.0.2-1 (using dcp110clpr-1.0.2-1.i386.deb) ... Unpacking replacement dcp110clpr ... Setting up dcp110clpr (1.0.2-1) ... ln: creating symbolic link `/usr/lib/libbrcompij2.so.1.0': File exists ln: creating symbolic link `/usr/lib/libbrcompij2.so.1': File exists ln: creating symbolic link `/usr/lib/libbrcompij2.so': File exists After installation, the printer is listed at the cups server, but does not work (no command has any effect on printer (which is, of course, on and connected)). Anyone has found some working solution? Thanks, Ondra

  Read the article

• Can't ping other machines in my network

  - by judahgabriel

  I've got 3 machines on my network, all running Windows 7. None of them can ping each other, can't see each other on the network, can't see shares, can't remote desktop, can't see any homegroups. They are all on the same workgroup. They are all connected to the same wireless, WPA2 secured network. They all worked together nicely until I added a password to my wireless network. After that, and after reconnecting all the machines to the password-protected network, they can't see each other. Any ideas what could be wrong?

  Read the article

• Connecting to Google SMTP with Konica Minolta Printers

  - by VictorKilo

  I have spent the better portion of two days trying to get a number of Bizhub MFCs to connect to Google's SMTP service. Our company recently switched from an exchange server, which handled SMTP requests to Gmail. We have 20 branches each with different MFCs. I was able to get the Cannons connected, but the Konicas are giving me major problems. The three models that are giving me issues are the C203, C250 and the C280. I have used the following: smtp.gmail.com port 465 Gmail Username/Pass aspmx.l.google.com port 25 no authentication aspmx.l.google.com port 25 Gmail Username/Pass None of these methods are working despite the fact that all of those have worked on different makes/models. Any help would be greatly appreciated, I'm at my whit's end.

  Read the article

• PHP failing to connect to GMail via IMAP [Edited!!]

  - by Alexander

  I have some php code that I'm trying to use to connect to gmail using imap. Here's the code: $hostname = '{imap.gmail.com:993/imap/ssl/novalidate-cert}INBOX'; $tmp_username = 'username'; $tmp_password = 'password'; $inbox = imap_open($hostname, $username, $password) or die(imap_last_error()); And I get this error output everytime i try to connect: Warning: imap_open() [function.imap-open]: Couldn't open stream {imap.gmail.com:993/imap/ssl/novalidate-cert}INBOX in /var/www/PHP/EmailScript.php on line 14 Login aborted I dont understand what could be wrong!! I've heard of people having SSL errors but this doesnt seem to be one of those. Please please please help me!!!!! Edit: When trying to connect to imap.gmail.com through telnet-ssl i get the following output: Trying 74.125.155.109... Connected to gmail-imap.l.google.com. Escape character is '^]'. And Nothign else happens

  Read the article

• Internet access only works after turning off and on the local connection

  - by AgentFire

  Every time I turn on the computer, it has no internet access. The network card is connected to a router which broadcasts the internet all over the office LAN. Once I turn off and then on the local connection (or network card), the internet access works. Rebooting and logging out/in again does not help. Only the turning off and on the network card gives me internet access. Why is that? How do I fix it?

  Read the article

• Can't ping self

  - by Paddy

  I have a wireless internet connection setup on my Mac. (v10.5.6) Am connected to the internet and everything is running smoothly. I recently discovered a quirky behaviour while setting up apache web server. When i typed in my dynamic ip (http://117.254.149.11/) in the webbrowser to visit my site pages it just timed out. In terminal i tried pinging localhost and it worked. $ ping localhost PING localhost (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.063 ms 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.056 ms 64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.044 ms But if i pinged my ip it would just time out. $ ping 117.254.149.11 PING 117.254.149.11 (117.254.149.11): 56 data bytes ^C --- 117.254.149.11 ping statistics --- 10 packets transmitted, 0 packets received, 100% packet loss Pinging any other site works though. I am completely stumped. Any help would be greatly appreciated.

  Read the article

• How much packet loss is normal?

  - by Fabian

  I started monitoring our network using SmokePing. Users occasionally complain about bad network connections, but the problems went away after some minutes usually. I now wanted to get some more quantitative information about those problems. SmokePing regularly pings servers inside our network, in a connected network and outside hosts. I only have a limited amount of control over our internal network and none at all for the connection to the outside and to the second network. I now see quite often (2-4 times a day) that packets to the second network and the outside are dropped. Most of the times it is 1-2 packets out of 20, sometimes more. Inside our internal network no packets are dropped. Is this an expected amount of packet loss, or does it indicate that something is wrong? I'm mainly wondering if I should bother the university IT department about it, or if I should just accept it as it is.

  Read the article

• Same SCSI drive appears multiple times on the controller list

  - by ohad

  Hi, I have an Adaptec AHA-2940UW SCSI adapter, to which I connected a single Atlas 10K III drive (and nothing more). When my computer loads up, the pre-OS Adaptec screen shows (I believe this is called the POST screen), where I can see the Atlas drive listed many times (i.e. with ID0, ID1, ... ID5, ID7, ID8,...,ID15 [ID6 is the adapter itself]) Using the same HD on an Adaptec AHA-2940UB the disk only shows once Since my OS hasn't been installed yet, I'm not sure if this is a problem (I would guess it is), and if so - how to solve it. Termination and multiple LUNs come mind, but the cable provides termination and I don't see why a hard drive would request multiple LUNs, especially considering it is not jumpered at all, and multuple LUN support is disabled in the Adaptec controller BIOS (via the SCSISelect utility) Thank you

  Read the article

• How to correctly set up iWARP? Preferably on loopback

  - by ajdecon

  iWARP is a protocol for doing remote direct memory access (RDMA) on top of TCP/IP, so that it can work with Ethernet and other network types as opposed to Infiniband. It works with many of the standard IB interfaces - the IB verbs, for example - so it's all pretty transparent. I'm doing some IB-verbs programming (mostly for the sake of learning about how they work better), and it'd be wonderfully convenient for me if I could use iWARP to do RDMA over my loopback interface, so that I could test some of my code without getting on our IB-connected cluster. :-) But I cannot figure out how to get a "local development environment" set up: there are no tutorials I'm aware of for even setting up iWARP from scratch on a server or a network interface. Can anyone give me a tutorial or point me in the right direction? Environment is Fedora 16 running in VirtualBox.

  Read the article

• Iptables mark incoming packet - vpn routing

  - by Tom

  I have connected my home to my workplace for out of house backup reasons through openvpn. The connection is working nicely. At work I have 5 fixed IP addresses. Now I would like to assign one of these IP addresses to be forwarded to my home machine. I have confirmed packet arrival at my home machine with tcpdump. The problem is that my default route at home is NOT the tun0 (naturally), but eth0 to my own ISP. So I created a separate routing table to route my tun0 packets back to where they belong, but do not how to mark the incoming packet which arrive through tun0 with iptables, so I can drive them back. I do not want any port restrictions, but only what comes from tun0 should leave through tun0 thanks tom

  Read the article

• is it possible for a router to provide different gateway?

  - by Hao

  i have tp-link wireless router 192.168.10.188, i was can make it function as DHCP provider(range 192.168.10.100 to 192.168.10.109). the only thing that i cannot make it work as intended, is for it to provide different gateway (192.168.10.1), the computers that obtain IP from that router properly get everything(dynamic IP and dns IP), but there is no function on that router to provide different gateway, the computers always get the router's address(192.168.10.188) as gateway. is there a router that can provide different gateway other than its own address? or the question should be, is the dhcp of a router can provide different gateway other than its own address? note: i cannot make the wireless router address as 192.168.10.1, we have main router(non-wireless, address is 192.168.10.1) that is connected directly to internet

  Read the article

• No sound through DisplayPort

  - by Chris Koknat

  I'm trying to connect my Elitebook 8440p laptop to my Samsung HDTV. The laptop does not have a HDMI connection, but it does have DisplayPort. I bought a DisplayPort-to-HDMI adapter here http://www.amazon.com/gp/product/B002CSRFD8/ref=oss_product, and connected it with a 3' HDMI cable. The video shows up fine, but there is no audio. DisplayPort, HDMI, and the adapter all support audio. I contacted HP tech support, who told me to update my sound drivers. I installed the driver and rebooted. Supposedly, I should see a "HD Audio" tab. No luck, even after installing the driver again and rebooting. HP closed the case. I'm using XP Pro.

  Read the article

• MSTSC Not working, disconnects shortly after connecting

  - by F4r-20

  I'm currently having a problem connecting remotely to a server. It is a brand new build Windows 2008 R2, remote users are enabled. I'm trying to connect from a Windows 7 machine. Everytime I remotely connect to the server it will stay connected for a matter of seconds (maybe 3-5) and then disconnect and I get the standard old cannot connect and list of reasons it could be. Then I cannot connect again and get this prompt until I restart the server. As soon as it's finished restarting, it happens all over again. The network and hardware configuration between the two machines is completely reliable. Does anybody know what else I could try? Thanks.

  Read the article

• xrander detect only one display

  - by cupakob

  Hi all, i have a problem, to get a picture on my tv over VGA (and also over S-Video to SCART). I've tried it first over xorg, but without success. After that i tried xrand, but xrander detect only my laptop display, here the output bufka [~] $ xrandr -q Screen 0: minimum 1680 x 1050, current 1680 x 1050, maximum 1680 x 1050 default connected 1680x1050+0+0 0mm x 0mm 1680x1050 50.0* 51.0 52.0 Any suggestions, how to solve the problem? My video card is Nvidia Geforce 8600M GT, TV is LG M227WPD and OS Ubuntu Lucid...

  Read the article

• How to reuse backup on Time Machine on Snow Leopard after a logic board change, after choosing wrong

  - by kmiffy

  After my logic board was replaced, I connected my laptop back to my network, and Time Machine gave me a popup, as shown on this thread: http://superuser.com/questions/78068/recycle-time-machine-for-new-machine/78264#78264 I misread the question and clicked on "Create New Backup" when I should have clicked on "Reuse Backup" to connect to my old backup file. How can I trigger that popup again? Turning Time Machine on and off does not work, and the instructions on forums to fix via terminal doesn't work because snow leopard is missing the fsaclctl command (and I'm also not familiar with terminal commands.) Thanks.

  Read the article

• RDP over VPN only

  - by shiva

  I know this question has been asked many a times here. But i want to gain certain perspective here. I have enabled VPN on certain systems and then can access remote system using rdp. However they can access the remote system without rdp as well. Is this because all these systems are in same lan group? How can i ensure that rdp works only when connected to vpn? I am looking at one vpn system and people should log into that system and then connect to vpn and then access remote system using rdp. I know that this can be achieved but i am not sure how to go about it. please guide me

  Read the article

• Problem with blue-sceens

  - by Oystein

  Hi I have a problem with my computer. I get bluescreens a lot. I get different bluescreen-codes everytime, and this happens randomly. This can happen when I boot my computer, when I'm surfing on the internett, when I'm away from the computer and are logged out... I tried to disconnect everything that was connected to my computer, beside the monitor. That didn't help. I have reinstalled Windows, changed memory, changed video card, but nothing of this helped, I still get bluescreens. I guess the problem here is the mothercard, CPU or HDD. But I want your opinion before I order anything new to my computer. Can you tell me what the problem is?

  Read the article

• Routing table change to access Internet over mifi

  - by Randall Blake

  I have two networks at home. One uses a Verizon mifi wireless on 192.168.1.1. The other uses a dlink router on 192.168.0.1. I have one laptop with two nics, one wireless and one not. The wireless nic connects to the mifi. The Ethernet nic connects to the dlink router. It's ip is 192.168.0.2. I also have a laptop with only one nic connected to the dlink on 192.168.0.3. I want to connect laptop 2 to the Internet. Can I do that by adding an entry to the routing table so that destination 0.0.0.0 routes to 192.168.0.2? If I do that, will laptop 1 "know" that it should route traffic from 192.168.0.3 to 192.168.1.1? Thanks for any assistance.

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >