Search Results

Search found 8185 results on 328 pages for 'transfer encoding'.

Page 163/328 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Large file copy from NFS to local disk performance drop

  - by Bernhard

  I'm trying to copy a 200GB file from an NFS mount to a local disk. The local disk is an XFS filesystem on a LVM on top of a RAID 5 system (hardware RAID controler). I'm using rsync to monitor the transfer speed. At the beginning the IO speed is about 200MB/s, stable for the first 18GB. But then the performance drops by a factor of 10-20 and never recovers to the initial rate. Sometimes it reaches about 50-100MB/s but just for a few seconds and then the process seems to hang for a bit. At the same time all file-stat operations on the target filesystem are blocking for a long time (minutes). Also interrupting the copy process blocks for several minutes, a sub-sequent delete of the partly copied file takes also several minutes. Any ideas what could be causing this?

  Read the article

• help building a PC that can image a dozen hard drives simultaneously

  - by Bigbio2002

  Not sure if this belongs on here or SuperUser, but here goes... I'm trying to figure out how to make a mass hard drive imaging PC out of COTS parts. A dedicated imaging device can do 10 drives at a time, but costs several thousand dollars. So far, I'm thinking to use several 3-port PCI-E Firewire cards, and use some kind of Firewire-to-IDE adapter to connect the drives themselves. The "software" would consist of scripting diskpart, or some other imaging utility. The problem is that I can't seem to find any sort of adapter. I could use standard external hard drive bays, but then I'd have a dozen power cables that I need to plug in. Ugly, messy, and inefficient. I picked Firewire over USB not only for better transfer speeds, but also because FW can deliver power over the bus (and could theoretically power a hard drive). Does anyone have any input on this?

  Read the article

• How to tell if you are connected to Wireless B, G or N?

  - by Raheel Khan

  I am using Windows 7 on all wired desktops and wireless laptops in my home network. I recently upgraded my Ethernet switch to Gigabit and instantly noticed an increase in throughput in wired devices. I also bought a Wireless-N WAP but with degredation in wireless file transfer speeds. I have been told that a number of reasons could affect wireless speeds including which WAP is used, how many wireless devices are connected, which security mode is used, etc. However, that remains irrelevant to my question. Each of my laptops claim to support Wireless-N but I cannot seem to figure out how to determine if the laptops are truly running Wireless-N or are connected to the WAP through some sort of mixed-mode. I do not have control of the WAP device so cannot tell what mode it is running in. Is there a way to tell which mode is being used and what the throughput is for each connected device without having access to the WAP interface?

  Read the article

• Emails intended as HTML are received as plain text

  - by Jeremy

  I'm regularly receiving emails from a well-known public website that read as plain text without carriage breaks or effective hyperlinks. My email client is Thunderbird. Thunderbird helpsite doesn't display an answer. And I'm reluctant to complain to the website if the problem is at my end. Message source for headers includes this: Content-Type: multipart/alternative; boundary=--boundary_9338_03b8c925-816e-4b55-95c4-b2593da7e5f6 The content in message source that follows the header is preceded by this: ----boundary_9338_03b8c925-816e-4b55-95c4-b2593da7e5f6 Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: base64 The content itself in message source reads typically like this: PCFkb2N0eXBlIGh0bWwgcHVibGljICItLy9XM0MvL0RURCBIVE1MIDQuMCBUcmFuc2l0aW9u YWwvL0VOIj4NCg0KDQo8aHRtbD4NCjxoZWFkPg0KPG1ldGEgaHR0cC1lcXVpdj0iQ29udGVu, etc.,etc. And, as I've said, the message in the viewing pane is unadulterated plain text. Can you tell me - where is it all going wrong? Thanks.

  Read the article

• vsFTPd and iptables - how to configure them in CentOS 5.5?

  - by Vincenzo

  I've installed vsFTPd in CentOS 5.5, on TWO servers, and added this rule to their iptable-s: -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j ACCEPT Looks like this is not enough, since when I'm trying to upload a file from one server to another, I'm getting this result (IP address is masked): # ftp 99.99.99.99 Connected to …com (99.99.99.99). 220 (vsFTPd 2.0.5) Name (99.99.99.99:root): vinny 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> ls 227 Entering Passive Mode (99,99,99,99,107,74) ftp: connect: No route to host I've found a few articles in the net about the second rule I have to add to iptables, but I didn't find the right syntax for it. Could you please help?

  Read the article

• SPF record doesn't work (not sure which DNS server to tweak)

  - by Ion

  Problem: Google (and perhaps others) marks our emails as SPF neutral. Let me give you some background about the setup: initially got a dedicated server (Hetzner) with Plesk installed to host a domain/web application, let's say: bigjaws.com. Plesk automatically creates a DNS zone for it with some records for the various services it provides out of the box, e.g. webmail.bigjaws.com as a CNAME to bigjaws.com to provide Horde/whatever, etc. Let me point out four relevant of these records (where XXX.XXX.XXX.158 is our dedicated IP): bigjaws.com. A XXX.XXX.XXX.158 mail.bigjaws.com. A XXX.XXX.XXX.158 bigjaws.com MX (10) mail.bigjaws.com. bigjaws.com. TXT v=spf1 +a +mx -all The above records are not(?) valid anymore though, because after using this dedicated server for a while, our site got bigger and bigger so we decided to move our operations over to AWS (EC2, RDS, ELB, etc), but we retained the mail functionality as is, i.e. emails from [email protected] are sent by connecting to our dedicated server where Plesk takes care of things. This was decided in order not to setup anything from scratch. Of course for all DNS-related things we now use Route53. In Route53 I have the following records: mail.schoox.com. A XXX.XXX.XXX.158 bigjaws.com. MX (10) mail.bigjaws.com bigjaws.com. SPF "v=spf1 +ip4:XXX.XXX.XXX.158 +mx ~all" From my understanding of SPF, the SPF status should have been passed: I designate that all email being sent by bigjaws.com from XXX.XXX.XXX.158 are valid/not spam (I added +mx there but I'm not sure if needed). When a mail server receives an email, doesn't it lookup the SPF record of the domain and checks against the IP it got the email from? Checking with spfquery: root@box:~# spfquery -ip XXX.XXX.XXX.158 -sender [email protected] -rcpt-to [email protected] StartError Context: Failed to query MAIL-FROM ErrorCode: (2) Could not find a valid SPF record Error: No DNS data for 'bigjaws.com'. EndError noneneutral Please see http://www.openspf.org/Why?id=employee1%40bigjaws.com&ip=XXX.XXX.XXX.158&receiver=spfquery : Reason: default spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com Received-SPF: neutral (spfquery: XXX.XXX.XXX.158 is neither permitted nor denied by domain of bigjaws.com) client-ip=XXX.XXX.XXX.158; [email protected]; If I go to the address listed above (openspf.org) it tells me that the message should have been accepted(!): spfquery rejected a message that claimed an envelope sender address of [email protected]. spfquery received a message from static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) that claimed an envelope sender address of [email protected]. The domain bigjaws.com has authorized static.158.XXX.XXX.XXX.clients.your-server.de (XXX.XXX.XXX.158) to send mail on its behalf, so the message should have been accepted. It is impossible for us to say why it was rejected. What should I do? If the problem persists, contact the bigjaws.com postmaster. Also, here are some headers from an email sent by one of our [email protected] addresses to a gmail.com address (by the way, bigjaws.de listed in the "Received: from" field was the initial domain hosted on the dedicated server before adding the .com one -- both are still listed as separate subscriptions under Plesk). Delivered-To: [email protected] Received: by 10.14.177.70 with SMTP id c46csp289656eem; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) X-Received: by 10.14.102.66 with SMTP id c42mr306186eeg.47.1382515860386; Wed, 23 Oct 2013 01:11:00 -0700 (PDT) Return-Path: <[email protected]> Received: from bigjaws.de (static.158.XXX.XXX.XXX.clients.your-server.de. [XXX.XXX.XXX.158]) by mx.google.com with ESMTPS id l4si19438578eew.161.2013.10.23.01.10.59 for <[email protected]> (version=TLSv1 cipher=RC4-SHA bits=128/128); Wed, 23 Oct 2013 01:10:59 -0700 (PDT) Received-SPF: neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=XXX.XXX.XXX.158; Authentication-Results: mx.google.com; spf=neutral (google.com: XXX.XXX.XXX.158 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] DomainKey-Signature: a=rsa-sha1; q=dns; c=nofws; s=default; d=bigjaws.com; b=WwRAS0WKjp9lO17iMluYPXOHzqRcOueiQT4rPdvy3WFf0QzoXiy6rLfxU/Ra53jL1vlPbwlLNa5gjoJBi7ZwKfUcvs3s02hJI7b3ozl0fEgJtTPKoCfnwl4bLPbtXNFu; h=Received:Received:Message-ID:Date:From:User-Agent:MIME-Version:To:Subject:Content-Type:Content-Transfer-Encoding; Received: (qmail 22722 invoked from network); 23 Oct 2013 10:10:59 +0200 Received: from hostname.static.ISP.com (HELO ?192.168.1.60?) (YYY.YYY.ISP.IP) by static.158.XXX.XXX.XXX.clients.your-server.de. with ESMTPSA (DHE-RSA-AES256-SHA encrypted, authenticated); 23 Oct 2013 10:10:59 +0200 Message-ID: <[email protected]> Date: Wed, 23 Oct 2013 11:11:00 +0300 From: BigJaws Employee <[email protected]> User-Agent: Mozilla/5.0 (Windows NT 6.2; WOW64; rv:24.0) Gecko/20100101 Thunderbird/24.0.1 MIME-Version: 1.0 To: [email protected] Subject: test SPF Content-Type: text/plain; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit test SPF Any ideas why SPF is not working correctly? Also, are there any DNS settings that are not needed anymore and create a problem?

  Read the article

• What's wrong with this vcl config for varnish-cache as load balancer?

  - by dabito

  I have the current configurations active on my default.vcl varnish file on the machine that balances the load for other two machines (the other two machines also have varnish active). My intention is to have this server do only the load balancing and the other machines do the processing and also their own caching. My problem is that even with the config testing (not even a stress test or anything, just a few requests a minute) I get the guru meditation error and have to restart varnish. This is the default.vcl for the load balancing server: backend vader { .host = "app1.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } backend malgus { .host = "app2.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } director dooku round-robin { { .backend = vader; } { .backend = malgus; } } sub vcl_recv { if (req.http.host ~ "^balancer.server.com$") { set req.backend = dooku; } } Am I doing something wrong or missing something? EDIT: This is varnishlog's output: 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839995 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839998 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840001 1.0 0 Backend_health - malgus Still sick 4--X--- 0 3 5 0.000000 3.846876 0 Backend_health - vader Still sick 4--X--- 0 3 5 0.000000 3.839194 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840004 1.0 14 SessionOpen c 10.150.7.151 38272 :80 14 ReqStart c 10.150.7.151 38272 458200540 14 RxRequest c GET 14 RxURL c / 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c / 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:44 GMT 14 TxHeader c X-Varnish: 458200540 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200540 1345840004.916415691 1345840004.965190172 0.020933390 0.048741817 0.000032663 14 SessionClose c error 14 StatSess c 10.150.7.151 38272 0 1 1 0 1 0 256 418 14 SessionOpen c 10.150.7.151 38273 :80 14 ReqStart c 10.150.7.151 38273 458200541 14 RxRequest c GET 14 RxURL c /favicon.ico 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c Accept: */* 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c /favicon.ico 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:45 GMT 14 TxHeader c X-Varnish: 458200541 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200541 1345840005.226389885 1345840005.226457834 0.000026941 0.000043154 0.000024796 14 SessionClose c error 14 StatSess c 10.150.7.151 38273 0 1 1 0 1 0 256 418

  Read the article

• TFTP PUT Failing Across Hosts

  - by Jason

  I have a TFTP server installed on a CentOS host. /etc/xinetd.d/tftp: service tftp { disable = no socket_type = dgram protocol = udp wait = yes user = root server = /usr/sbin/in.tftpd server_args = -c -s /var/lib/tftpboot per_source = 11 cps = 100 2 flags = IPv4 } If I try to PUT a file from a remote host to the host running the TFTP server, I get Transfer Timed Out - however, it does create the file in /var/lib/tftpboot but the file is empty. If I tftp from the tftp server to itself (localhost) and PUT a file, it works fine. I have verified that SELinux is disabled and IPTables are turned off. I can connect from the remote hosts with no issue - just seems to be the PUT I have issue with: [root@SVR01 TEST]# tftp 10.100.2.15 tftp> status Connected to 10.100.2.15. Mode: netascii Verbose: off Tracing: off Literal: off Rexmt-interval: 5 seconds, Max-timeout: 25 seconds tftp>

  Read the article

• Linux QoS: bulk data transmission during idle times

  - by syneticon-dj

  How would I do a QoS setup where a certain low-priority data stream would get up to X Mbps of bandwidth, but only if the current total bandwidth (of all streams/classes) on this interface does not exceed X? At the same time, other data streams / classes must not be limited to X. The use case is an ISP billing the traffic by calculating the bandwidth average over 5 minute intervals and billing the maximum. I would like to keep the maximum usage to a minimum (i.e. quench the bulk transfer during interface busy times) but get the data through during idle/low traffic times. Looking at the frequently used classful schedulers CBQ, HTB and HSFC I cannot see a straightforward way to accomplish this.

  Read the article

• How can I copy the output from a remote command into the local clipboard?

  - by cwd

  I use iTerm2 as my terminal client in Mac OS X. On the local system I can use pbcopy and pbpaste to transfer data between the system clipboard and the terminal, but of course this doesn't work when you're ssh'ed to another machine. Is there some way which I can take the result of a command and copy it to the clipboard automatically? Perhaps an applescript to grab the text on the iTerm windows, then get the next to last line? For instance, if I wanted to copy the current working directory: I run pwd, then use the mouse to select the text, and then press command + c. Is there any better / faster / automatic way of doing this? I'm not looking for a bulletproof solution that would work for every command (eg: might not work when there is a huge scrollback) - I'm just looking for something to make this task that I do quite often a little less tedious. Update I'm looking into using screen to do this, but I'm still not sure if it is possible.

  Read the article

• What's the easiest way to allow Exchange 2003 remote (no MSO client) users check their Mailbox size?

  - by Myrddin Emrys

  We are migrating from Exchange 2003 with no quota settings to Exchange 2010 with limited mailbox sizes. We are trying to get users to clean their mailboxes prior to the move to reduce the transfer load, as well as to comply with new quotas on the 2010 system. But many users access their mail through webmail only. I cannot see a way for users to access their mail store size in this manner. Has anyone else run into this problem? Is there a good way to easily let users check their own mailbox size? The only thing I've come up with as a workaround is a report that IT generates and mail-merge it out to users daily with their current mailbox size. This is cumbersome and time consuming compared to a way for them to check their own mailbox size however.

  Read the article

• Amazon EC2- micro-instance vs single small/medium instance

  - by shashankaholic

  I have a chat application using stack of Openfire, Tomcat6 and MySQL. Currently, i have installed all these servers on single Linux micro-instance(613 MB memory). Even in low user base 10-20 i am encountering CPU overload which is quite obvious here. As, i am new to Amazon EC2 can somebody suggest me how to scale up my architecture according to traffic use? should i use separate micro instances for every app server(openfire,mysql,tomcat6) should i use single small or medium instance for whole server stack. Some factors in context: high reliance on MYSQL high memory usage due to file transfer web-application interacting with other Amazon service like S3,SES

  Read the article

• Amazon EC2- many micro-instances vs single small/medium instance

  - by shashankaholic

  I have a chat application using stack of Openfire, Tomcat6 and MySQL. Currently, i have installed all these servers on single Linux micro-instance(613 MB memory). Even in low user base 10-20 i am encountering CPU overload which is quite obvious here. As, i am new to Amazon EC2 can somebody suggest me how to scale up my architecture according to traffic use? should i use separate micro instances for every app server(openfire,mysql,tomcat6) should i use single small or medium instance for whole server stack. Some factors in context: high reliance on MYSQL high memory usage due to file transfer web-application interacting with other Amazon service like S3,SES

  Read the article

• How to use symbolic links in windows server 2008R2 across the network (mklink)

  - by server info

  I have One Server (Srv1) which holds data with file shares and the storage is full. Now I have second Server (Srv2) which has alot more space. No I would like to transfer all the data von Serv1 to Serv2 and have links to the new destination. I found mklink very useful here but unfortunately it does not work over the network. Which also points the docu out. People heavily rely on the path's so it would be helpful if somone has a pointer for me... how to handle symbolic links a cross the network with Windows Servers. I am running Windows Server 2008. Thanks for any help

  Read the article

• How can I format a USB drive as FAT from a MacBook Pro?

  - by Edward Tanguay

  I plugged in a 250GB USB hard drive into my MacBook Pro and want to format it in FAT so I can transfer files back and forth between a windows machine. (My windows7 machine only formats in exFAT which my Snow Leopard 2.6.4 doesn't support until I do the update). So I want to format it on the mac. but when I right click on the drive, it gives me the options to eject, copy, but not to format. I can go into Disk Utilities, click on Partition, but the only option is the "Mac Journaled format". How can I Format my USB drive as FAT from my MacBook Pro?

  Read the article

• How to connect a remote IP Phone to our VOIP Network?

  - by Mistiry

  We have an IP phone system in our office, and about 8 VoIP phones running on the system. We have a remote worker, who is literally states away. We'd like to connect his phone to our VoIP network, so that he has a business phone and an extension to which we could transfer calls. I was thinking, although I don't know for sure, that a pair of Cisco routers could be used in some way to make this work. I imagine a VPN solution, where I have one router connected to the phone network and the other router connected to the remote phone. Then have a site-to-site VPN set up so that the remote router... And that's where I'm stuck. I know the remote router will need to use the DHCP server of the phone system. I've never set up something like this, so I am seeking the help of the community here. What is the best way to get this remote VoIP phone RELIABLY connected to our internal VoIP network?

  Read the article

• How To Create An FTP User That Has Permission To EVERYTHING

  - by Serg

  I've spent the last two hours trying to create an FTP user so I can transfer some files over to my Wordpress blog folder. /var/www/sergiotapia.me I'm using vsftpd and Ubuntu 12.04 for my FTP server and I've read tons of documentation, none of which seem to work. I still cannot log in with the FTP user, let alone test if I even have the read/write file permissions. Can a Linux guru here, help me out with a small step by step? I'm comfortable with the terminal and nano, so that's not an issue - I'll SSH into my box. Just tell me what to do and what commands to run. Specifically, this user needs to have read and write access to the /var/ folder and anything within it. I want to have 1 user that can do whatever the heck he wants on my Ubuntu 12.04 VPS machine.

  Read the article

• Corrupted file, hard drive test?

  - by all-R

  Hi guys, I'm currently on a macbook with a 1TB external hard drive connected trough a USB hub wich is connected on my macbook. The problem is, my disk, wich is partitioned in 2 (one HFS+ and one NTFS) keeps getting corrupted, recently it was my HFS+ partition, I could not repair it using the Apple's Disk utility, but was able to backup my files. Is it synonym that my hard drive is failing? Is it because of my USB hub? I also keep all my iTunes library on my external HD (HFS+ partition), and did a lot of transfer lately, adding files, removing etc. the last time, my partition got corrupted after a lot of deleted items. If anybody has an idea of what to check first, what could cause the problem, I would appreciate it :) Thanks!

  Read the article

• FTP upload stalls at same point every time on FileZilla

  - by John

  On two different FTP accounts, I am having problems uploading files. I can login and see the contents of the dir, and start an upload. Using Filezilla the transfer seems to always stall at either 0.9% or 1.2% (always those two numbers) and may simply hang, or keep restarting and then again stop at the same point. WindowsXP FTP is not great but I get similar types of problems there... it starts uploading and after a short while I get a timeout error. FTP used to work fine, and I don't know if it's these accounts in particular (both have the same service provider although purchased on opposite sides of the world) or if "FTP is broken on my PC"... can that even happen?!

  Read the article

• 550 operation not permitted using FTP

  - by monkey_boys

  I'm using FTP to manage some files on a site I run but keep seeing this (truncated) error log: Command: DELE calendarpermission.php Response: 550 calendarpermission.php: Operation not permitted [...] Command: DELE button_down.gif Response: 550 button_down.gif: Operation not permitted Command: CWD /domains/example.com/public_html/admincp Response: 250 CWD command successful Command: PWD Response: 257 "/domains/example.com/public_html/admincp" is the current directory Command: RMD control_examples Response: 550 control_examples: Operation not permitted Command: CWD /domains/example.com/public_html Response: 250 CWD command successful Command: PWD Response: 257 "/domains/example.com/public_html" is the current directory Command: RMD admincp Response: 550 admincp: Operation not permitted Status: Retrieving directory listing... Command: PASV Response: 227 Entering Passive Mode (122,155,5,50,138,244). Command: MLSD Response: 150 Opening ASCII mode data connection for MLSD Response: 226 Transfer complete Status: Directory listing successful Status: Set permissions of '/domains/example.com/public_html/admincp' to '777' Command: SITE CHMOD 777 admincp Response: 550 CHMOD 777 admincp: Operation not permitted What do I do to solve this?

  Read the article

• Can I take a HDD in Raid1 and plug it straight into a different machine?

  - by jacko

  I would assume that I can just take my HDD out of my NAS (in raid1 mirror) and plug it into another enclosure and have it work off the bat but I'd like to make sure... Any ideas? Edit: My current setup is a Netgear ReadyNAS in (hardware) raid1. I'm hoping to replace this with a home theatre type PC (possibly running Ubuntu), and would like to migrate my data without having to do a bulk transfer over my network between the 2 machines. Can anyone confirm the case for the Netgear ReadyNAS?

  Read the article

• teamviewer display is slow to refresh

  - by brunoais

  I'm using teamviewer from time to time to connect my portable computer with my desktop computer when I need to check on something (personal use). One of the main things I've been noticing is that it is quite slow transfering the screen updates that keep happening. This happens more frequently when I'm moving full windows or when I open a window or when watching a small movie clip. I've tested the lowest maximum p2p speed I ever got in the last week between both and it is the desktop's upload speed of 6MB/s with the ping of 40ms (usually ~15 ms). With this I was expecting to have very sharp image and fast transfer speeds which is not what is happening. Just to clarify, both computer's individual core's CPU is not reaching its peak (25%) while teamviewer is active, so the encryption and decryption is not the cause. Why my connection between both computers so slow?

  Read the article

• Throttling apache downloads selectively

  - by Synchro

  I have a linux box running Debian Sarge (old I know) and apache 2.0.54. It serves two kinds of files - regular web pages and small images, and a lot of large podcast mp3s. The podcast downloads swamp the connection and make the rest of the site unresponsive, so I'm looking to throttle the data transfer rate (not the request rate) of just the podcasts. I've set up haproxy using this technique which does what it says it will, but solves a different problem - even only 5 simultaneous podcast downloads is enough to saturate the link. In a perfect world, haproxy would support per-connection throttling, but it doesn't. So far I've looked at mod_bw (won't compile for me, seems unsupported), mod_cband (unsupported, widely reported as problematic) and iptables using tc. The iptables approach would allow me to throttle things, but would not be at all selective, slowing down everything on the server, not just the podcasts, so would just move the bottleneck without changing overall behaviour. Ideas?

  Read the article

• Transferring videos from Sony Video Camera to PC via USB connection

  - by Mehper C. Palavuzlar

  I have a Sony video camera (DCR-TRV340e) and loads of video tapes that I like to transfer to my PC. The camera has USB connection and I've loaded its driver with no problems. Which video software do you recommend me to use? I want to have my videos in XviD format with maximum 1 GB for a 1 hour film. How much time does it take to do that for a 1 hour film? Should I use USB connection or another type of connection? Detailed information about connection and software settings would be highly appreciated.

  Read the article

• How do I analyze an Apache Bench result?

  - by Alan Hoffmeister

  I need some help with analyzing a log from Apache Bench: Benchmarking texteli.com (be patient) Completed 100 requests Completed 200 requests Completed 300 requests Completed 400 requests Completed 500 requests Completed 600 requests Completed 700 requests Completed 800 requests Completed 900 requests Completed 1000 requests Finished 1000 requests Server Software: Server Hostname: texteli.com Server Port: 80 Document Path: /4f84b59c557eb79321000dfa Document Length: 13400 bytes Concurrency Level: 200 Time taken for tests: 37.030 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 13524000 bytes HTML transferred: 13400000 bytes Requests per second: 27.01 [#/sec] (mean) Time per request: 7406.024 [ms] (mean) Time per request: 37.030 [ms] (mean, across all concurrent requests) Transfer rate: 356.66 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 27 37 19.5 34 319 Processing: 80 6273 1673.7 6907 8987 Waiting: 47 3436 2085.2 3345 8856 Total: 115 6310 1675.8 6940 9022 Percentage of the requests served within a certain time (ms) 50% 6940 66% 6968 75% 6988 80% 7007 90% 7025 95% 7078 98% 8410 99% 8876 100% 9022 (longest request) What this results can tell me? Isn't 27 rps too slow?

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >