Search Results

Search found 93727 results on 3750 pages for 'code documentation'.

Page 1644/3750 | < Previous Page | 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651  | Next Page >

  • Netdom to restore machine secret

    - by icelava
    I have a number of virtual machines that have not been switched on for over a month, and some others which have been rolled back to an older state. They are members of a domain, and have expired their machine secrets; thus unable to authenticate with the domain any longer. Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server ldap/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Warning Event Source: LSASRV Event Category: SPNEGO (Negotiator) Event ID: 40960 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: The Security System detected an authentication error for the server cifs/iceland.icelava.home. The failure code from authentication protocol Kerberos was "The attempted logon is invalid. This is either due to a bad username or authentication information. (0xc000006d)". For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c000006d Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 3210 Date: 14/05/2009 Time: 10:24:54 AM User: N/A Computer: TFS2008WDATA Description: This computer could not authenticate with \\iceland.icelava.home, a Windows domain controller for domain ICELAVA, and therefore this computer might deny logon requests. This inability to authenticate might be caused by another computer on the same network using the same name or the password for this computer account is not recognized. If this message appears again, contact your system administrator. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: c0000022 So I try to use netdom to re-register the machine back to the domain C:\Documents and Settings\Administrator>netdom reset tfs2008wdata /domain:icelava /UserO:enterpriseadmin /PasswordO:mypassword Logon Failure: The target account name is incorrect. The command failed to complete successfully. But have not been successful. I wonder what else needs to be done?

    Read the article

  • Netgear WG311 v2 not identified on Windows 7

    - by iamrohitbanga
    I have a Netgear WG311 v2 wireless card. It was working fine on vista. Now I have installed Windows 7 and the device is not identified. Device Manager shows it as an Ethernet card. When I update the driver using the list provided with the Windows distribution. It shows it under Wireless devices in Device Manager but it says device cannot start code 10. Any idea on how to install it.

    Read the article

  • !! 0xc01a00d !! aka Vista won't boot

    - by Chris
    Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

    Read the article

  • Shell Script if else

    - by user34104
    #!/bin/bash echo "Int. a number" read num1 echo "Int. another numer" read num2 if ["$num1"="$num2"]; then echo "Equals" else echo "Dif" fi if["$num1"<0]; then echo "The number $num1 is negative" else if ["$num2"<0]; then echo "The number $num2 is negative" fi # this code is not working, i've something wrong when i see if the number is < 0. thanks

    Read the article

  • Email delivery error

    - by Tim
    I sent an email, but immediately got a reply saying: Final-Recipient: rfc822;[email protected] Action: failed Status: 5.0.0 (permanent failure) Diagnostic-Code: smtp; 5.1.2 - Bad destination host 'DNS Hard Error looking up smtpint.xxx.edu (MX): NXDomain' (delivery attempts: 0) I was wondering what this error report means, where in the delivery route the error happened, who should be contacted to solve this issue and how to solve it? Thanks and regards! I also appreciate if someone can explain a bit more about the mechanism behind the email delivery.

    Read the article

  • What does the filesystem give me?

    - by Alec
    I'm writing a specialised database. It currently sits atop of ext4, with one big file that it reads and writes to. I'm wondering whether it would be worth forgoing the filesystem and reading and writing directly to the device. I already use O_DIRECT, so as far as I can tell it wouldn't require much of a code change. What might the risks, advantages and disadvantages of forgoing the filesystem be? Is it likely to improve performance, or harm it?

    Read the article

  • Deploying Django App with Nginx, Apache, mod_wsgi

    - by JCWong
    I have a django app which can run locally using the standard development environment. I want to now move this to EC2 for production. The django documentation suggests running with apache and mod_wsgi, and using nginx for loading static files. I am running Ubuntu 12.04 on an Ec2 box. My Django app, "ddt", contains a subdirectory "apache" with ddt.wsgi import os, sys apache_configuration= os.path.dirname(__file__) project = os.path.dirname(apache_configuration) workspace = os.path.dirname(project) sys.path.append(workspace) sys.path.append('/usr/lib/python2.7/site-packages/django/') sys.path.append('/home/jeffrey/www/ddt/') os.environ['DJANGO_SETTINGS_MODULE'] = 'ddt.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler() I have mod_wsgi installed from apt. My apache/httpd.conf contains NameVirtualHost *:8080 WSGIScriptAlias / /home/jeffrey/www/ddt/apache/ddt.wsgi WSGIPythonPath /home/jeffrey/www/ddt <Directory /home/jeffrey/www/ddt/apache/> <Files ddt.wsgi> Order deny,allow Allow from all </Files> </Directory> Under apache2/sites-enabled <VirtualHost *:8080> ServerName www.mysite.com ServerAlias mysite.com <Directory /home/jeffrey/www/ddt/apache/> Order deny,allow Allow from all </Directory> LogLevel warn ErrorLog /home/jeffrey/www/ddt/logs/apache_error.log CustomLog /home/jeffrey/www/ddt/logs/apache_access.log combined WSGIDaemonProcess datadriventrading.com user=www-data group=www-data threads=25 WSGIProcessGroup datadriventrading.com WSGIScriptAlias / /home/jeffrey/www/ddt/apache/ddt.wsgi </VirtualHost> If I am correct, these 3 files above should correctly allow my django app to run on port 8080. I have the following nginx/proxy.conf file proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; Under nginx/sites-enabled server { listen 80; server_name www.mysite.com mysite.com; access_log /home/jeffrey/www/ddt/logs/nginx_access.log; error_log /home/jeffrey/www/ddt/logs/nginx_error.log; location / { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy.conf; } location /media/ { root /home/jeffrey/www/ddt/; } } If I am correct these two files should setup nginx to take requests on the HTTP port 80, but then direct requests to apache which is running the django app on port 8080. If i go to mysite.com, all I see is Welcome to Nginx! Any advice for how to debug this?

    Read the article

  • nginx - Redirect specific page paths to https while keeping everything else on http (in a single server call)?

    - by Kris Anderson
    From what I've gathered so far it's clear that running if statements in nginx should be avoided at all costs. Most of the examples I've found so far regarding specific page redirects involve multiple servers being used. But, isn't that a bit wasteful? I'm not sure, but I would think multiple servers to accomplish this would be somewhat slower then a single server when under heavy load. My current server call is this: server { listen 10.0.0.60:80; listen 10.0.0.60:443 default ssl; #other code } What I want to do is redirect certain http requests to https requests. For example, I want /login/ and /my-account/ to always be forced to use SSL. If you're on /help/ though, I want that served over the default http. Is there a way to accomplish this within a single server call? Or is there no downside to using 2 server calls to get this working? nginx seems to be under pretty active development and a lot of the older guides I've followed were from times when you couldn't listen to requests for port 80 and 443 within the same server call. But now that nginx has been updated to support that (I'm running 1.2.4), I'm wondering if there's a "best practice" way of handling this today. Any help would be greatly appreciated. EDIT: I did find this guide: http://redant.com.au/blog/manage-ssl-redirection-in-nginx-using-maps-and-save-the-universe/ and I updated my code as follows: map $uri $my_preferred_proto { default "http"; ~^/#/user/login "https"; } server { listen 10.0.0.60:80; ## listen for ipv4; this line is default and implied listen 10.0.0.60:443 default ssl; if ($my_preferred_proto = "none") { set $my_preferred_proto $scheme; } if ($my_preferred_proto != $scheme) { return 301 $my_preferred_proto://mysite.com$request_uri; } It's not working though. When I change the default to https everything is redirected to SSL so it does somewhat work. But the redirect of /#/user/login is not redirecting to HTTPS. Any ideas? Also, is this a good way to go about this?

    Read the article

  • VMWare tools not installing with an error

    - by JDS
    VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

    Read the article

  • Cannot reinstall Windows on Toughbook CF-19, OEM or upgrade issue?

    - by j03lar50n
    My Toughbook (CF-19) has a 'Windows Vista Business OEMAct, Panasonic' COA on the bottom of the unit. When I extracted the key before reformatting - it was a 'Windows XP Professional' Product Name and the Product ID code has 'OEM' in it...and I can confirm this upgrade was last OS installed (w/ Service Pack 3) - but there was the tablet functionality. This extracted product key isn't working with any version of Windows I try installing. XP Pro, XP Pro Tablet 2005 OEM, Tablet XP OEM. Any insights?

    Read the article

  • command to show the shell command prompt

    - by LinuxPenseur
    Hi, Is there a shell command to display the command prompt. I will explain what i want through the illustration below. When i execute script.sh, i should get the following output $sh script.sh $ /* command prompt and then print hi */ hi My script.sh is like this #! /bin/bash <command to display the shell command prompt> echo "hi" exit 0 what should the code that has to go in the place of angle brackets to get an output like above? Thanks

    Read the article

  • command to show the shell command prompt

    - by LinuxPenseur
    Hi, Is there a shell command to display the command prompt. I will explain what i want through the illustration below. When i execute script.sh, i should get the following output $sh script.sh $ /* command prompt and then print hi */ hi My script.sh is like this #! /bin/bash <command to display the shell command prompt> echo "hi" exit 0 what should the code that has to go in the place of angle brackets to get an output like above? Thanks

    Read the article

  • How can i recompile the python 2.7 with enable shared option

    - by user31
    I installed 2.7 with yum. But i didn't used enable shared option so i am not to run mod_wsgi with djnago. Now i want to recompile with enable shared option. Is there any esay way to do that Although mod_wsgi will still work when compiled against a version of Python which only provides a static library, you are highly encouraged to ensure that your Python installation has been configured and compiled with the '--enable-shared' option to enable the production and use of a shared library for Python. http://code.google.com/p/modwsgi/wiki/InstallationIssues

    Read the article

  • Ruby on rails gems and win 7

    - by cbrulak
    I have a networked home share (at work). This is my HOMEPATH,HOMESHARE,etc. When I installed the rails gem and other the .gems folder was created there (which is on a network drive) and consequently any code that needs a gem or a gem lookup is slow. And I'm wondering which environment variables need to be corrected. I've googled this but most results are dealing with cygwin so any ideas? Thanks

    Read the article

  • SFTP File Restrictions.

    - by The Rook
    Is it possible to use SFTP on Linux and restrict a user account to ONE directory such that no other directory listing can be obtained? Yes, I must use SFTP, FTP is only used by people that love getting hacked. For instance I want someone to modify files in /var/www/code/ but I don't want them to be able modify anything else. I don't even want them to see the contents /tmp/. (I will accept a "quick and dirty" solution, as long as it is secure.)

    Read the article

  • In Apache, how do I set up password protection?

    - by rphello101
    I'm attempting to set up a server using Apache. In the conf file, I inserted the code: <Directory /> Options FollowSymLinks AllowOverride AuthConfig AuthType Basic AuthName "Restricted Files" AuthBasicProvider file AuthUserFile C:\...\serverpass.txt Require user Admin </Directory> In order to try and get Apache to require a password. I created the username and password with htpasswd -c. When I got to localhost though, it doesn't prompt me for a username and password?

    Read the article

  • Microphones not working on Apple macbook Air 1,1 (Early 2008) under Linux

    - by jj_p
    I'm running Linux on an mba. I can't make the microphones (neither external nor internal) work. I test using alsamixer and arecord -d 5 test-mic.waw together with aplay test-mic.waw It seems there is a problem with kernel trying to decipher Apple (intentionally) corrupted 'bios', in particular the mic pins are wrongly assigned. As far as we are concerned here, is there any difference between using EFI and BIOS-compatibility mode? (see https://wiki.archlinux.org/index.php/MacBook where they claim to have everything working out of the box on mba1,1) A nice proposal would be to compile the latest Linux kernel and run hda-jack-retask to find the right configuration (in the case of Realtek codec, the missing things I'm supposed to check are either some vendor-specific COEF verbs, EAPD or GPIO setup.), and then come up with a kernel patch to address the issue. Since I'm not that familiar with this last part of the story, can anyone help me through this process? Some useful data: The output from alsa script run as root http://www.alsa-project.org/db/?f=adae8ebee1007043fe83414ac4972319e02255fa The command hda-jack-sense-test -a (with external mic in) Pin 0x14 (Internal Speaker): present = No Pin 0x15 (Green HP Out): present = Yes Pin 0x16 (Not connected): present = No Pin 0x17 (Not connected): present = No Pin 0x18 (Not connected): present = No Pin 0x19 (Not connected): present = No Pin 0x1a (Not connected): present = No Pin 0x1b (Not connected): present = No Pin 0x1c (Not connected): present = No Pin 0x1d (Not connected): present = No Pin 0x1e (Not connected): present = No Pin 0x1f (Not connected): present = No Most likely the chip is Realtek ALC885 (compare also ALC889A) http://guide-images.ifixit.net/igi/bBTSqaeK5JpQ1AWe.large , although at the moment alsa reads it as ALC889A Takashi Iwai's tutorial https://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio.txt Some people researched the original files from a running OS X installation on this same model (I think the relevant files are AppleHDA.kext/Contents/MacOS/AppleHDA AppleHDA.kext/Contents/PlugIns/AppleHDAHardwareConfigDriver.kext/Contents/Info.p????list AppleHDA.kext/Contents/Resources/layout12.xml.zlib AppleHDA.kext/Contents/Resources/Platforms.xml.zlib) http://www.insanelymac.com/forum/topic/220090-alc889a-pin-configuration/#entry1554954 Datasheet http://www.realtek.info/pdf/ALC885_1-1.pdf (from the same Realtek, one can also try to download Linux driver, but this is just taken from ALSA project, as stated in the readme file.) Compare with this Arch guy http://www.alsa-project.org/db/?f=3ca8243c0626844f0264a3faad0aa72018bc14f4 Here for the first time support to audio (except mics) for mba1,2 (which is morally the same as 1,1) is patched into the kernel http://www.alsa-project.org/pipermail/alsa-devel/2010-February/025511.html The same jack supposedly works both for HP and ext MIC, I think it's called TRRS, and it's the same as the one used e.g. for iphones This guy might have done a similar job, though to a more recent version and for sound globally, not just mics: http://blogs.aerys.in/jeanmarc-leroux/2013/09/15/fixing-2013-macbook-air-ubuntu-sound-issue/ (this is mirror to http://unix.stackexchange.com/questions/73044/microphones-not-working-on-apple-macbook-air-1-1-early-2008-under-linux )

    Read the article

  • Why does the MSDN library constantly say "Information Not Found"?

    - by Zian Choy
    Environment: VS 2008 Pro SP1 MSDN Library for VS2008SP1 Sample Code: Dim userDataset = New DataSet Dim myDataAdapter = New SqlDataAdapter("SELECT UserName FROM tblwebUsers WHERE name = @person", connect) myDataAdapter.SelectCommand.Parameters.Add("@person", SqlDbType.NVarChar) When I put my cursor on the "d" in "Add" and press F1, I get an "Information Not Found" error from the MSDN Library. Does anyone have any suggestions for addressing the issue?

    Read the article

  • Force view text file instead of download in Firefox?

    - by davr
    Often times I'll click on a random link to a .sh or .py or .cpp or ... file in Firefox, and all I want is to view the code. I don't have a Firefox handler set up for every text file extension under the sun, and I don't want to have to. Is there an easy way to force Firefox to view the file as text instead of trying to save (or open in external app)?

    Read the article

  • Unable to view data in notepad.

    - by Saran
    I have a java code that reads an excel file and writes it to a text file. When i get the output text file, I can see only symbols like this in the notepad. "????????????????????????????" But if i open the text file in wordpad or ms-word, the data is correctly displayed. What could be the error?

    Read the article

  • rumtime error 424 on comm port

    - by Neha Hafeez
    I am trying to rectify this problem which i am facing on Visual Basic 6.0. my devices connected on Comm port are not detected simultaneously on visual Basic. Erroor msg displayed on this line of code: MSComm5.PortOpen = True HELP

    Read the article

  • Sensitive data deletion (remote)

    - by José Antonio Silva
    Hi, I'm just finished my Amazon EC2 migration and I want to delete all the files (databases, source code) from the old servers. The problem is that the servers are in California and my business is in Chile, soo I only have ssh access to that servers. I'm planning to sell the servers and I'm wondering if there is a way to perform a low levele deletion remotely of the specific files and folders. Thanks in advance! José Antonio

    Read the article

  • What text file search tool are you using?

    - by user156144
    I am working on legacy projects with thousands of files spanning more than 10 projects. I am wondering what other people are using for searching string in a text file. I am using windows and i typically search on 10,000 files to make sure some code is not called from other places. I've tried numerous text search tools mentioned here such as Actual Search & Replace, Ultraedit, notepad++ but they all take very long time to search due to the large # of files they have to look into.

    Read the article

< Previous Page | 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651  | Next Page >