Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 166/216 | < Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• IP Address on internet access shared over ad-hoc wifi network

  - by Jacxel

  The Situation When im staying at my girlfriends we both like to have internet access on our laptops but her accommodation don't allow wireless routers. My Question My question is if I set up an Ad-Hoc network to share the internet connection as shown here on How To Geek. Will my laptop be acting as a wireless router or will the connection all go through my laptop as one ip address so it appears to be my computer accessing the webpages etc, that my girlfriend actually is. i would be interested in knowing any additional information that could help sove this problem eg. if connectify would do what i want.

  Read the article

• Should I upgrade my LinkSys WRT54GL firmware?

  - by Reid

  I have a LinkSys WRT54GL v1.1 which currently has stock firmware version 4.30.7. I see that version 4.30.14 is available. The router works fine now, and the release notes look uninteresting except for one line in v4.30.9: "Resolves issue with Linux kernel vulnerability". I have remote management turned off. I'm aware of the 3rd-party firmwares but the stock firmware works fine for me at the moment, so I don't have an interest in those. Is the status quo fine or should I upgrade the firmware? (It's a bit of a pain since the config has to be saved and reloaded, and obviously any mucking with firmware is risky.)

  Read the article

• Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

  - by Frederic

  I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

  Read the article

• Connecting two pcs through cable, at the same time as wireless

  - by Steffen

  I've got 2 pcs setup with WLAN - however when I copy files between the machines it takes forever (obviously, since I run 801.11g). So I thought, why not just connect them directly with a cable (my wireless router is the other end of the house, that's why I don't use cables to that) However how should I configure the LAN connection on each machine, so I can use it for transferring files between them, whilst using my WLAN to access the Internet ? I was thinking about letting one machine be gateway, but then Windows pops up with a lot of warnings (basically it says this won't work when you're using two disjoint networks) And now I'm at a loss as to what to try.

  Read the article

• RRAS Problem routing to central site from RRAS server only?

  - by TomTom

  Given is an office connected to headquarters using a RRAS bridge (2 virtual machines using RRAS to route between the two networks). Naming: The office is A, the RRAS on A is a-lnk. THe headquartters is B, b-lnk the RRAS machine there. The VPN works perfectly - machines can ping and work between the sites. Domain controllers on both ends replicating, DFS working, remote desktop working. All in all... everything is fine. EXCEPT: a-lnk itself can not reach any machine in B. This would normally not be troublesome (noone ever does anything on a-lnk), but there are two exceptions: * a-lnk is supposed to get it's license from a KMS in B, so not being able to reach B means it is not prolonging. * a-lnk is supposed to pull updates from a WSUS in B - and not being able to reach B means - no updates. Given that thigns work (and security is a minor issue - A-lnk is not reachable from the internet as it is behing a NAT hardware anyway) this got not handled for months. I just wan to get this item ticked off now. Anyone an idea what this is? It definitely is not a "dns does not work" or "routing in general is bad" item, as any computer in A can connect to any computer in B, and the other way arount - only the RRAS computer itself seems to do something really awkward. Platform for both: 2008 R2 standard.

  Read the article

• Cascading switches: uplink to uplink?

  - by wuckachucka

  I'm a bit confused as to why I haven't seen any references online to using Switch A's uplink port (1Gbps, 24-port 10/100) to connect to Switch B's uplink port: everything I've seen -- including documentation, forums, articles, etc. -- has Switch A's uplink port going to one of Switch B's 10/100 access ports. As I understand it, the Uplink port (besides greater speed normally) is no different than another port except that it's "internally crossed-over" so that you can use a straight cable with it. I've also seen documentation on using the uplink port to connect a switch to a gateway router, or even a server, as it provides greater bandwidth than the access ports, but yet not sure why nobody seems to be cross-uplinking, even when there's 2 uplink ports available on some higher-end switches. Switch in question is Linksys SRW224P (x2). Am I missing something?

  Read the article

• Process to replace motherboard and keep CPU

  - by jolivier

  My motherboard has been diagnosed with the Sandy Bridge issue (http://vip.asus.com/eservice/changeSandybridge_MB.aspx?slanguage=en-us) so I am asked by my reseller to send back my motherboard to have a new one compatible with the previous one. My problem is that I have a not cheap Intel CPU currently on it, with its standard heatsink/fan. I would obviously like to keep it to plug it on the new motherboard. I am quite woried about the thermal paste. I was planning to: Remove the CPU and the HSF together (I think they are sticked to each other). Try to separate the CPU and the HSF (I'm not sure how) Clean both of the surfaces When the new motherboard is here, put the CPU back on it. Have new thermal paste to put again on the CPU, put it on the CPU Add the HSF again Do you see any problem about this process? Recommendations? Is it possible to keep the CPU and the HSF together for the whole process or is it impossible to plug the CPU back on the new motherboard in this case? Thanks in advance for your answers. Olivier

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• Access Methods to a computer Using MAC Address

  - by Dimal Chandrasiri

  I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

  Read the article

• Microsoft Forefront Management Gateway 2010 - Which topology to choose for monitoring only server?

  - by MadBoy

  Hello, I've installed Forefront and wanted to use it as monitoring traffic solution until we decide to put it as a router. I've 2 nic's assigned to this virtual machine. One NIC has connected port which is "mirror port" of our WAN redirected on switch so it sees all the network traffic flying by. The other NIC is internet access. This server is located inside our lan network. What topology should i choose and which options I should look at to be able to see which traffic is used (SMTP, WWW etc) and who does what? We had cases of infected machines with spam and we want to be able to see that some machine is sending large amounts of mails. Is that possible ?

  Read the article

• SATA Driver for Acer Aspire One D257

  - by Robert Niestroj

  i have a Acer Aspire One D257. In this netbook the hard disk is defect so i bought a new one. Now i want to reinstall Windows 7. Im using an external DVD Drive plugged into USB. The Windows 7 DVD is staring, Win7 setup is starting and when it comes to Hard Drive options it says that no drive was detected and i should try search for drivers. It shows me this window: Screenshot from web Now i cant find the right drivers for this netbook to continue with the installation. The laptop has the newest BIOS - 1.15, it is reset to factory default settings except that i enabled the Boot Menu prompt with F12. From the Acer Support Website i've downloaded the SATA AHCI Driver and the Chipset Driver. I unpacked both to a USB flashdrive in seperate folders. When i select the SATA AHCI Driver it does not find any drivers. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it shows one driver: Acer HWID (path_to\1.inf). When i continue with this driver i got an error message that says something like: No new devices found. Check if the driver files are on the installation disk. When i show him the Chipset Driver it sees a lot more driver. When i uncheck the checkbox "Hide drivers that are not compatible with hardware on this computer" it show some drivers: Intel N10 Family DMI Bridge Intel N10/ICH7 Family PCI Express Root Port Intel N10/ICH7 SMBUS Controller Intel N10/ICH7 Family USB Universal Host Controller Intel N10/ICH7 Family USB2 Enhanced Host Controller Intel N10/ICH7 Family Interface LPC Controller When i uncheck this checkbox i get a lot more drivers, and some SATA Drivers but the also do not work. I get the same error message as before. Can someone help me find a driver that should work or am i doing anything else wrong?

  Read the article

• Error while setting up Anywhere Access on Windows Server 2012 Essential (personalized domain name from Microsoft)

  - by Thomas

  I am trying to setup Anywhere Access on a Windows Server 2012 Essential Release Candidate, but keep getting this error: "The domain name was not setup for your server. Wait a few minutes and run the wizard again. An unknown error occurred. Please wait a few minutes and then try again". These are the options that I selected in the Wizard: I want to set up a new domain name Get a personalized domain name from Microsoft Entered my Windows live id and password xxxx.remotewebaccess.com And on the next page the error is displayed. I have setup my router (Linksys WRT160N) to forward all TCP traffic to the Server. UPnP is also enabled. If I hit my public (dynamic) IP (http://188.182.194.182/) I get the Windows Server 2012 homepage. Any ideas?

  Read the article

• 'DNS server isn't responding' error in windows 7 home premium

  - by pradeeptp

  Hi All, I bought a brand new Dell Studio 1558 just last week. It has windows 7 home premium 64-bit installed on it. My friend who is occupying the adjacent room has a laptop with windows XP. Both of us are connecting to the same wireless router of the hotel. My friend is able to connect to the wireless network without any trouble, but when I try to connect, I get the error "DNS service isn't responding". I get this error when I run the troubleshooting option. I met two more people in the same hotel with win XP laptop and they too dont have any problem. I have gone to possibly all the forums and website but I haven't been able to fix this error :(. I have done all the basic troubleshooting but I have no luck yet. Pls help. Following is one forum where the problem seem to have been trouble shooted but not for all. http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/eeb84518-903d-46d1-9398-80cf211878d7

  Read the article

• Block p2p downloading in my office?

  - by Andrew

  I work in an education office in a third world country. We pay for internet by the megabyte (no other choice) and have lately been using an incredible amount of bandwidth. This is because the office staff have found out about p2p sharing. As far as I know, Limewire is the only program they're using, but I'm sure it's just a matter of time before they discover the more general world of bittorrent. Using only a linksys router (that I could flash), is there any way for me prevent the office from destroying our bandwidth cap by downloading personal items (against policy). Even semi-fixes would be better than nothing.

  Read the article

• Can't connect to YouTube from specific network

  - by Tyilo

  Using my current network, I am unable to connect to http://www.youtube.com/. It doesn't matter what browser I use or if I use a cli-command (wget, curl). Error in Google Chrome: Oops! Google Chrome could not connect to www.youtube.com Error using curl: curl: (7) couldn't connect to host If I use nslookup to get the IP-address of YouTube, I get 173.194.32.32. If I go to http://173.194.32.32/ in my browser it can connect, but as Google is probably checking the Host HTTP-header, it shows Google's frontpage instead. There is no blocked websites on the router and other devices on the network seems to work. My computer only has this problem on this specific network. I am using Mac OS X 10.8.2 on a MacBook (mid 2009).

  Read the article

• How to go about scheduling a task in windows 7 to change wireless connection

  - by Skindeep2366

  This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

  Read the article

• Intranet Setup for Small business any resources?

  - by Rogue

  Want to setup an intranet for a small business setup. Current Setup 28 computers running Windows ( few older pc's run Windows Xp but most run Windows 7) Spare Dell Pentium 3 which can run as a server. 6 switches spare NIC's and lots of lan cable available for networking. 3 Independent Internet connections Currently we have 3 independent networks which share internet connections, each network uses a different internet connection. Current network is setup solely to share the internet connection. What I need to achieve in this intranet Setup one common network. Instant file transfer via local network (maybe setup a file server?) Local text and voice messenger software Bridge the 3 internet connections and route all the internet connections from the main server Ability to allow or deny internet access to any computer on the network. Remote access from the main server to the client pc's on the network to debug software issues What operating system should I use on the main server? Do I need a hardware firewall? Any setup guides / resources or how-to's on how I can achieve the above requirements.

  Read the article

• Windows 7 Utlimate x64 - No Internet access

  - by rafek

  I've just installed Windows 7 Ultimate x64. As all of my computers at home I've connected to my router via wifi (open/wep). And what has happened is that Wireless Connection is Connected but with No Internet access -- my ipconfig says: Autoconfiguration IPv4 Address : 169.254.33.161 Subnet Mask : 255.255.0.0 Default Gatewawy : (empty) After ipconfig /renew I get: An error occurred while renewing interface Wireless Network Connection : unable to contact your DHCP server. Request has timed out. [..] I'm looking for a solution for 2 hours now...

  Read the article

• D-Link DNS-323 NAS firmware update

  - by Mark Beaton

  Hi all, I've got a D-Link DNS-323 NAS enclosure holding a bunch of multimedia files that I've (possibly stupidly) just updated the firmware on, from 1.03 to 1.08. The updater indicated it applied the firmware patch successfully, but after rebooting it I can no longer get into it via the web interface, either via the static IP I had assigned it before the update, or by any of the DHCP-assigned addresses that I can see are currently assigned by my router. The unit just sits there, with the drives (2x512 set up as RAID-1) thrashing away seemingly forever... So, my question - has anyone had a similar experience with one of these units? Any advice etc? I've googled the hell out of it, and can't find anything useful.

  Read the article

• Hosting 3 domains on 3 PC (1 domain per PC) with only 1 static IP address

  - by StealthRT

  Hey all i am trying to figure this out here. I have 3 PC's that are hooked into my router which i have a static IP for. I am currently hosting a web site (ex: blah1.com) on the 1st PC but have yet to connect PC 2 and 3 up to the network. That one PC thats online is using port 77. I direct all 80 traffic to port 77 using that servers IP address (192.168.x.xxx) My question is, how can i direct traffic for my other 2 domains (ex: blah2.com and blah3.com) to the 2 individual PC's (ip's) as i already am doing with the 1st PC if i can only use one port 80 to direct taffic to the website in?

  Read the article

• networking fails when DNS servers are specified manualy

  - by Matthew Scouten

  When I let Windows-7 use DHCP to find its own DNS server, everything works fine. Then I use ipconfig to get the IPs of the DNS servers in question, and specify them manually. Now the network stops working. (I need to do this because my next step is to restore the router that is going to lie about the proper DNS server. Don't ask why, it is required by my father's work. The IT there are not exactly on the ball.) Why would this make a difference? It is the same set of servers, just obtained differently.

  Read the article

• Trouble accessing network drives in Windows 7

  - by Warlax

  Hi, Recently purchased a LaCiE network drive. Connected it to my router, configured it, added a user for myself. Installed the "Network Assistant" that came with it - no problem. Went to My Computer Network, found the network drive - was prompted for a login/password to see the contents, types \user and password (leading slash to get rid of DOMAIN) and accesses contents. There is one open share that I can access/mount without problem and there's another share with my user name as set-up via the network drive's web-based config. Double-clicked on that, prompted again. user/password doesn't work! It says I have no permissions but the user/pass combination is PERFECT. Some Windows Vista posts talk about a Local Security Policy menu - but that's nowhere to be found. Any ideas? (Windows 7 Professional BTW).

  Read the article

• Why is Internet access and Wi-Fi always so terrible at large tech conferences?

  - by Joel Spolsky

  Every tech conference I've ever been to, and I've been to a lot, has had absolutely abysmal Wi-Fi and Internet access. Sometimes it's the DHCP server running out of addresses. Sometimes the backhaul is clearly inadequate. Sometimes there's one router for a ballroom with 3000 people. But it's always SOMETHING. It never works. What are some of the best practices for conference organizers? What questions should they ask the conference venue or ISP to know, in advance, if the Wi-Fi is going to work? What are the most common causes of crappy Wi-Fi at conferences? Are they avoidable, or is Wi-Fi simply not an adequate technology for large conferences?

  Read the article

< Previous Page | 162 163 164 165 166 167 168 169 170 171 172 173  | Next Page >