Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 168/216 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• Samsung i780 networking problem

  - by Infinity

  Hello guys! Maybe this is not the right place to ask this, but I give a try for it. Please don't rate it down, just ignore it if you don't like. So I have a Samsung i780 mobile phone and I would like to use the internet through my wireless router. I have connected to it. I got an IP address. My laptop is also connected to the same wireless network and I can ping the mobile phone and I get answer. When I open the internet explorer and enter an address it says that it cannot connect to the internet. I have googled very much, but can't find the problem. What do you think, what is the solution?

  Read the article

• Port forwarding not working?

  - by rphello101

  I'm trying to set up an Apache Server to be accessed publicly. I'm using a Netgear R4500 router hooked up to a Motorola SB6121 modem. I can access my server on my computer by typing in my IP address. After following the instructions to forward port 80 so I can access the server from other computers, it does not work (see image). I get "This webpage is not available". I am forwarding to the IP address of my computer. Using this Network Port Scanner Tool, it says "80/tcp filtered http", which, as I understand it, means forwarding did not work correctly. In my Apache httpd file, I have: ServerName 192.168.1.13:80 and Listen 192.168.1.13:80 Anyone know what's wrong or have something I can try? click to enlarge

  Read the article

• apache returning "The connection was reset"

  - by usjes

  One of my dedicated servers had some network issue today and the data center has to replace some router. Since then the sites on that server returns "The connection was reset" error most of the time. I tried installing nginx and it opens better, but it still shows the error sometimes. Everything in the config seems normal, what could be causing this error? UPDATE: Just noticed that in whm apache status there are always only 1 requests currently being processed, 8 idle workers. I know for sure the server received thousands of requests per minute. What could be limiting this to such a low number?

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• Files turned into folders on external hard drive

  - by Kashif

  I have a networked hard drive where I like to store audio/video/software and all sorts of other files for my house. While the software files are all intact and working, many of my video and audio files have been turned into folders! Can anyone explain why this is happening, how I can prevent it, and if it is possible to revert these "folders" back into files. Thanks much! An example of what the folders are named: "Highschool Graduation.avi", "Birthday party.avi", "Somesong.mp3" The HDD is connected to a Linksys E4200 router (Firmware Version: 2.0.37). This is how the HDD is networked.

  Read the article

• Regarding temperature in our server cabinet

  - by kafka

  We have a floor standing server cabinet, which sits in the corner of our office. There is no AC in the office, and the average temperature is around 21C (70F). The server cabinet currently contains 2 tower servers, a switch and a router. It's well enough ventilated, but does get understandably warm in there. We've recently put a thermometer in there to monitor the temperature, and recently I've noticed the temperature hit 33C (91F). What I'd like to know is if this temperature is too high, and whether there is a maximum temperature we should not be exceeding?

  Read the article

• Un-balanced network speed although using fiberoptic cable line

  - by Hoàng Long

  I'm not sure this is a right place to ask this question, but there's a strange thing that I don't quite sure what the reason is. My company has hired a fiberoptic cable line for network use (Wifi and cable through a router). But the strange thing is that, whenever someone view YouTube or listen stream music, then network speed for all the others become extremely slow. The download speed for that person is about 4-5 MB/s (or more), but others suffer. I'm still a newbie about networking. But I know there should be a solution. Could anyone tell me a way to stop this bad behavior? It's not possible for asking people not viewing YouTube, since that's part of their jobs. Any insights about this problem would be very welcome.

  Read the article

• Windows VPN not authenticating from ADSL to Wireless link

  - by deanvz

  I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

  Read the article

• Linux IPv6: DHCP and /127 prefixes

  - by Jeff Ferland

  I've tried multiple pieces of DHCP client and software in attempting to setup a solution for allocating a /127 prefix to virtual machines so that each maintains its own layer 2 isolation. Because there would only be one host assigned to each network, a /64 is impractical. While the prefix size could reasonably be somewhere in the /64-127 range, the crux of the problem has been the same regardless of the software used in configuring: the DHCP call to bring up the interface uses the address advertised by DHCPv6 and inserts two routes: the /127 given by the router advertising packets and a /64 as well. Any thoughts on why I'm getting the additional route added across dhcp client vendors?

  Read the article

• Self-hosted browser-based remote desktop script?

  - by rlsaj

  I need a self-hosted browser based remote desktop script that will connect me from any PC to my work PC. I need to either host this script within my own dedicated hosting or on my work PC. The PC that I need to remote into is always the one PC (Win7) and the IP never changes, and I have access to the Router/Firewall within. I have tried many remote desktop services and applications - LogMeIn, Team Viewer, (Ultra/Tight) VNC, GoToMyPC and iTeleport Connect and even Windows Remote Desktop - and the web services (or ports) are blocked at whatever free wi-fi/hotel/coffee shop I am at. Note that I will need to be able to access this from any PC, so I won't be able to install any applications (or use any portable software) - hence my thinking that it will need to be browser based on a standard (not blocked) port. If I can set up a web based remote desktop application - really a homebrew LogMeIn - then I should solve my problem. What is the best option here?

  Read the article

• Laptop connects to other network but not to my home wireless

  - by Nilesh

  My home network's wireless SSID is say "XYZ" I also have an ethernet wire from the same router. I have two laptops A and B Earlier both A and B were able to connect to my home internet through the ethernet and wireless. Suddenly, the laptop B can no longer connect to XYZ or through ethernet. When I do plug the wire, i get the connection icon all green but when I try to access any web page it errors out (page not found) But strangely laptop B connects to my neighbours wireless SSID "ABC". I have also tested laptop B with other networks and it connects fine. Laptop A and many other devices still connect fine with my home wireless "XYZ" Strange thing is when my laptop B connects wireless through XYz, it gets the IP address but then none of the browsers (chrome,firefox, IE) can show any web pages. What settings should I be checking on laptop B that is preventing it to connect to my home internet. Thank you

  Read the article

• How to set the IP address in a customized OpenWRT compilation

  - by Berdus

  I have been struggling today customizing OpenWRT. I checkout the stable using SVN, "make menuconfig" to customize the image, "make" it and run it on a router. Almost all my modifications work, except for the (Seemingly trivial) task of changing the default 192.168.1.1 address. I tried numerous files (scripts as well as config files) but I can't seem to change it (I can change it for a brief moment after boot using the "preinit" file, but after a few seconds it reverts to default). I suspect I should be setting it in the /etc/network file, but modifications there seem to be overwritten during boot. Maybe it has something to do with the br-lan interface? Does anybody have some thoughts on the subject? Thanks!

  Read the article

• network user isolation

  - by seaquest

  My question is for a network with a Linux iptables router gateway. How can it be possible to prevent inter-network traffic of those users. Think this case as a public network, IPs are distributed through linux gw and users are authenticated thru the gateway. We want to protect public users from public users. Network is not wireless and I can not use Wireless AP user isolation. Actually I have a simple method. Subnet the network into /30 mask. Give minimum IP of each subnet to the gateay and ditribute those /30 IPs from the subnet. But this is pretty costly for such an aim. I want to ask for other methods Thanks.

  Read the article

• Format External HD on Airport Extreme Base Station?

  - by David.Chu.ca

  I just got an Airport Extreme Base Station. I am planning to use this one replace my current Linksys router. This works fine. My another purpose of getting this device is to use its USB port to connect to several external HDs as my backup Time Machine. I can see one 500GB HD through Airport Base Station. However, I cannot format it by using Disk Utility. What I did is to connect the HD to my iMac directly first and then clean and format the disk by Disk Utility application. Then I move the HD to the Airport Base Station. After that I can designate the HD as my Time Machine destination. Is there any way to format the HD connected to Airport Base Station? Any issues to use an external HD through Airport Base Station for Time Machine backups?

  Read the article

• Is there anything that can be done to make X forwarding over LAN less painful?

  - by Earlz

  I have two *nix machines that I like to remotely do graphical things sometimes with. One of those machines is my Arch Linux media server, and another is my OpenBSD router/general server. My current task was installing a Windows XP over virtual box on my media server. I preferred to do the installation from my main workstation so that I could continue to watch TV from my media server on it's "actual" display. I soon noticed that X forwarding is quite painful though, even over low-latency LAN connections. Are there any settings I can tweak to make it a bit less painfully slow, jittery, and laggy? My LAN is rather small, 100Mbit, and ping times to the other box average at about 0.15ms. Also, I know Virtualbox has a VNC mode it can use instead of doing X forwarding, but this particular task was just an example

  Read the article

• Blocked connections passing through firewall. What is wrong?

  - by Kiranu

  In our company we have a small business router (Cisco RV082) on which we are using its standard configuration (block all incoming traffic). We also have an SMTP relay configured (using WS2008R2) so that our internal applications can send email through google apps (which requires authentication). The thing is that the server was being used to send spam. We fixed the problem by only allowing the server to relay email from our internal IP address range (10.0.0.0/16). My concern is that there was a way by which external IPs connected to the network and that underlying problem has not been fixed, but I cannot imagine how these machines connected. Any thoughts?

  Read the article

• which vista services can be disabled with impunity?

  - by GwenKillerby

  I use Vista on a HP pavilion DV2 laptop. When I look through all the services my laptop starts, it really seems there's way too much of it. I multi boot with XP and 7. Both startup in 40 seconds. Vista takes four minutes. Is there some software that can determine which services I don't need? On 7, there's no propietary HP stuff at all, yet it seems to run fine. Because all these service, there's a LOT of them and some just sit there doing nothing, monitoring for updates I don't really need or want or need to know about the second they're available. my laptop is the only computer i use at home, there's no home network, aside from the modem-router, which is cabled, not wifi. Take for instance Parental controls, and stuff for people with bad eyesight, Tablet PC. I really never use any of that stuff. Hope this question is specific enough. thanks, Gwen.

  Read the article

• How to increase Remote Desktop resolution?

  - by BugAlert

  I'm using Windows 7 on a PC and connect to it via Remote Desktop Connection for Mac by MS, using a Mac. On the Mac, I have a 27" Display with 2560 x 1440 px resolution. The PC has a high performance graphics card (one of those that needs an additional power supply). Both machines are connected via network cable to a router. So network should be insanely fast. However, the max resolution I can get is 1400 x 1050. The PC just has a old and bad 21" monitor connected to it. How can I increase the resolution to 2560 x 1440 to work fullscreen with the Apple LED Cinema Display via Remote Desktop? Maybe I shouldn't even ask, because I already experience some lag at the low resolution of 1400 x 1050. But I guess this can be resolved as well?

  Read the article

• PC power supply & normal range for voltages reported in BIOS hardware monitor?

  - by Chris W. Rea

  I'm trying to diagnose whether my computer has an ample power supply. Sometimes when I play a video-intensive game, both monitors lose the video signal, even though the computer remains on and sound playing. A theory I have is: the video card isn't getting sufficient power. I can't imagine it's overheating because the machine is well-ventilated and the video card isn't hot to touch when this happens. Anyway, in my PC's BIOS there's a Hardware Monitor page, and among other voltages reported (such as CPU, DRAM, South Bridge, etc.) I can see the following values: 3.3V 3.152V 5V 4.944V 12V 11.872V Are those the voltages used by peripherals? What voltage should I be referencing if I want to know what my video card (PCI Express) is consuming? What is the normal range of values reported for those? My values above appear to be under by approximately 4.5%, 1.1%, and 1.1% respectively. Is that cause for concern? How else should I be determining if my power supply is "right-sized" for my PC and video card, or am I perhaps barking up the wrong tree?

  Read the article

• Sonicwall NSA 3500, public ip for SSL VPN clients is not visible

  - by SlyMcFly

  I have a Sonciwall NSA 3500 and I'm setting up the SSL VPN according to this guide. I get through setting up the Sonicwall router, but then to test it says "Users can now go to the public IP of the sonicwall. Notice the new “click here for SSL login” hyper link". However, when I go to the public ip of the Sonicwall I don't get a web page, it just times out. Is there some other setting that I'm missing in order to make the SSL VPN login page public?

  Read the article

• I get regular power surges and my UPS ticks a lot due to a welding plant. Is this good or bad?

  - by EApubs

  In our home, there is a mechanic who often use a welding plant. When he use it, I think we get a power surge. My UPS ticks madly (not beep, it ticks). Sometimes, I even lose power to the keyboard. When typing, some keys get missing. 1) My question is, is it good for the computer? The UPS claimed to have surge protection. But isn't it working? What should I do to protect my PC? 2) The second question is, I also have a broadband router which is not connected to the UPS. Will it be effected?

  Read the article

• Vmware Workstation Development Server on Laptop

  - by Koobz

  I'm running an Ubuntu guest OS on my Windows 7 laptop. Currently, I have it set up for bridged networking. The guest is os is configured for a static ip of 192.168.1.115, which depending on the network I'm connected to, may not be available. When I want to view my development work I hit that up in my web browser. I'm really looking for the following scenario: 1) My guest OS ip address stays constant. 2) I can access my guest os even if I don't have an internet connection, or a lan/router. 3) I can share files with my guest/host. How does one accomplish this using VMware Workstation?

  Read the article

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• Multiple VLANs on a single subnet

  - by mstaessen

  I would like to establish the setup shown below. The image is taken from (http://gcharriere.com/blog/?p=620) and explains how to set this up on a brocade device. I would like to use an ubuntu server to do the routing. Right now, the switch and the server/router are connected with a trunk and the server uses the vlan package, kernel module and (inner) subnets for routing. I would like that: no IP addresses get lost in the subnetting (outer subnet is /26, inner subnets are /28) I don't want the rigorous subdivision of my outer subnet. I want to assign a VLAN to any IP in the outer subnet. How do I need to configure my interfaces? What is the "ubuntu" translation of "ip follow ve"? Thanks!

  Read the article

• Performance issues with jms and spring integration. What is wrong with the following configuration?

  - by user358448

  I have a jms producer, which generates many messages per second, which are sent to amq persistent queue and are consumed by single consumer, which needs to process them sequentially. But it seems that the producer is much faster than the consumer and i am having performance and memory problems. Messages are fetched very very slowly and the consuming seems to happen on intervals (the consumer "asks" for messages in polling fashion, which is strange?!) Basically everything happens with spring integration. Here is the configuration at the producer side. First stake messages come in stakesInMemoryChannel, from there, they are filtered throw the filteredStakesChannel and from there they are going into the jms queue (using executor so the sending will happen in separate thread) <bean id="stakesQueue" class="org.apache.activemq.command.ActiveMQQueue"> <constructor-arg name="name" value="${jms.stakes.queue.name}" /> </bean> <int:channel id="stakesInMemoryChannel" /> <int:channel id="filteredStakesChannel" > <int:dispatcher task-executor="taskExecutor"/> </int:channel> <bean id="stakeFilterService" class="cayetano.games.stake.StakeFilterService"/> <int:filter input-channel="stakesInMemoryChannel" output-channel="filteredStakesChannel" throw-exception-on-rejection="false" expression="true"/> <jms:outbound-channel-adapter channel="filteredStakesChannel" destination="stakesQueue" delivery-persistent="true" explicit-qos-enabled="true" /> <task:executor id="taskExecutor" pool-size="100" /> The other application is consuming the messages like this... The messages come in stakesInputChannel from the jms stakesQueue, after that they are routed to 2 separate channels, one persists the message and the other do some other stuff, lets call it "processing". <bean id="stakesQueue" class="org.apache.activemq.command.ActiveMQQueue"> <constructor-arg name="name" value="${jms.stakes.queue.name}" /> </bean> <jms:message-driven-channel-adapter channel="stakesInputChannel" destination="stakesQueue" acknowledge="auto" concurrent-consumers="1" max-concurrent-consumers="1" /> <int:publish-subscribe-channel id="stakesInputChannel" /> <int:channel id="persistStakesChannel" /> <int:channel id="processStakesChannel" /> <int:recipient-list-router id="customRouter" input-channel="stakesInputChannel" timeout="3000" ignore-send-failures="true" apply-sequence="true" > <int:recipient channel="persistStakesChannel"/> <int:recipient channel="processStakesChannel"/> </int:recipient-list-router> <bean id="prefetchPolicy" class="org.apache.activemq.ActiveMQPrefetchPolicy"> <property name="queuePrefetch" value="${jms.broker.prefetch.policy}" /> </bean> <bean id="connectionFactory" class="org.springframework.jms.connection.CachingConnectionFactory"> <property name="targetConnectionFactory"> <bean class="org.apache.activemq.ActiveMQConnectionFactory"> <property name="brokerURL" value="${jms.broker.url}" /> <property name="prefetchPolicy" ref="prefetchPolicy" /> <property name="optimizeAcknowledge" value="true" /> <property name="useAsyncSend" value="true" /> </bean> </property> <property name="sessionCacheSize" value="10"/> <property name="cacheProducers" value="false"/> </bean>

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >