Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 169/216 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• Cannot assign port 4 to WAN on TP-Link WR740N by DD-WRT wiki

  - by Victor Sergienko

  I'm following the DD-WRT instruction to get TP-Link WR740N v3's Port 4 on a different VLAN, but this doesn't happen. First, I have no "Setup VLANs" settinngs tab in DD-WRT v24-sp2 (07/20/12) std r19519. I can get Internet on Wi-Fi if assigning eth1 to "WAN Port", but then all Ethernet ports get on the same VLAN and any wired connection grabs the DHCP address and Internet connection from router. When following the "old" instruction, if I run, say, nvram set vlan2ports="2 5*", should there appear a new interface, vlan2, in ifconfig, after ifconfig vlan2 up? It doesn't - does it mean there is no support for different VLANs in my software/hardware? What am I missing? Is it impossible to create more VLANs on TP-Link740?

  Read the article

• How do I set up a virtual host?

  - by user1698332

  My router redirects port 80 to port 8080. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• Virtualbox port forwarding with iptables

  - by jverdeyen

  I'm using a virtualmachine (virtualbox) as mailserver. The host is an Ubuntu 12.04 and the guest is an Ubuntu 10.04 system. At first I forwarded port 25 to 2550 on the host and added a port forward rule in VirtualBox from 2550 to 25 on the guest. This works for all ports needed for the mailserver. The guest has a host only connection and a NAT (with the port-forwarding). My mailserver was receiving and sending mail properly. But all connections are comming from the virtualbox internal ip, so every host connection is allowed, and that's not what I want. So.. I'm trying to skip the VirtualBox forwarding part and just forward port 25 to my host only ip of the guest system. I used these rules: iptables -F iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -A INPUT --protocol tcp --dport 25 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -s 192.168.99.0/24 -i vboxnet0 -j ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp -i eth0 -d xxx.host.ip.xxx --dport 25 -j DNAT --to 192.168.99.105:25 iptables -A FORWARD -s 192.168.99.0/24 -i vboxnet0 -p tcp --dport 25 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.99.0 -o eth0 -j MASQUERADE iptables -L -n But after these changes I still can't connect with a simple telnet. (Which was possible with my first solution). The guest machine doesn't have any firewall. I only have one network interface on the host (eth0) and a host interface (vboxnet0). Any suggestions? Or should I go back to my old solution (which I don't really like). Edit: bridge mode isn't an option, I have only on IP available for the moment. Thanks!

  Read the article

• Lost contact with my NAS after changing its IP

  - by Beles

  I did some brain-dead reconfiguring of my D-Link DNS-323 NAS some days ago. I have a home network where each computer gets a dynamically allocated IP address starting at 192.168.1.100. The irritating point (for me at least) was that the NAS changed IP if the power went down or I turned off the router. I then had to remap a drive-letter to point to the new IP address of the NAS. To remedy that I configured the NAS to have a static IP, 192.168.0.10. I had no good reason to choose that IP, other than I found it in a user manual for the NAS. After I changed the IP and rebooted the NAS it disappeared from the network and was never to be found again. Now I have a black brick standing in my home, looking good, but "dead". Could anyone point me in a direction which helps me solve this problem? I have about 100gb worth of pic of my children on this brick so I really want it back :-) Sincerely,

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• Altq limits not being applied to UDP transfers

  - by overkordbaever

  I have a OpenBSD server acting as a router/firewall with yhr packet filter ruleset shown below, a linux server, and a linux client. When transferring files (using netcat) by TCP, the limits are applied (for example the 100mbit limit in the example), though when transferring data by UDP, the limits aren't applied; the file always takes the same amount of time no matter the queue bandwidth limit I set (I can even turn off the queues completely, and will still get the same result). Why aren't the queuing rules applied to UDP packages? The rules used: #queue rules altq on { $int_if, $ext_if } cbq bandwidth 100Mb queue { def, low } queue def bandwidth 0Mb cbq(default) queue low bandwidth 100Mb cbq #Passrules test pass out quick from $int_if to $ext_if queue low pass in quick from $ext_if to $int_if queue low pass out quick from $ext_if to $int_if queue low pass in quick from $int_if to $ext_if queue low I suppose this may be related a question I've previously asked, though since it's more of a separate question, I suppose a separate question should be used for this

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• block access to wrt from vlan using iptables dd-wrt

  - by NitroxDM

  I set up multiple isolated vlans in dd-wrt. Now I need to forward a port to vlan2. I isolated the vlans using: iptables -I FORWARD -i br0 -o vlan2 -j DROP iptables -I FORWARD -i br0 -o vlan3 -j DROP iptables -I FORWARD -i br0 -o vlan4 -j DROP Now I need to block a clients on each vlan from accessing the router. This doesn't work: iptables -I INPUT -i br0 -o vlan2 --dport telnet -j REJECT --reject-with tcp-reset I'm new it iptables... am I missing something?

  Read the article

• Windows 8.1 killed my wifi

  - by char1es

  Was running Windows 8 on a Lenovo G780 and updated to windows 8.1 Wifi does not work anymore, i always receive a dns server not responding error. I have tried using public dns servers from Google but with still no results. I've restarted my router with no results. All other devices on my network are having no trouble at all. I've tried updating the wireless driver but the manufacturers website claims that the Win8.1 driver should be updated with the update from windows. So i cant find a wireless driver... Anyone else having this error and does anyone have any ideas on how to fix it?? EDIT: here are the driver details: Broadcom 802.11n Network Adapter Provider: Microsoft Driver Date: 2013-05-31 Driver Version: 6.30.223.102 Digital Signer: Microsoft Windows Thanks

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• Set up Windows SBS dns server and vpn clients from brench office

  - by mn

  I have got some clients from bench office which connects vpn to main office. The Router from bench office assigned addresses from DHCP 192.168.1.0/255.255.255.0 and remote gateway assigned vpn ip addresses 10.10.20.0/255.255.255.0. There is a DNS server (Active Directory Win SBS 2000) and vpn client are registered with vpn address (10.10.20.0/255.255.255.0 and domain company.com.pl). I would like to register also primary bench subnet 192.168.1.0/255.255.255.0 with domain for example company.vpn.local I want to access vpn hosts for example: dev3.copmany.pkb.local and dev3.company.com using my Win SBS 2000 DNS server.

  Read the article

• Virtualizing an Inline network appliance with VirtualBox (or VMWare)

  - by Tzury Bar Yochay

  My device, which is a Linux based IP in-liner is transparent to the network peripherals, that is, no IP address assigned to any of its interfaces. For the sake of the conversation, let's use ADSL connection as an example, while the device is inspecting the bi-directional traffic, the network is behaving same as if device was not there, attached to the wire (see Physical setup at the attached diagram). I wonder if I can enclosed that "device" within a Windows machine and have it operated virtually so it still seats inline between the ADSL router and the Windows netwroking interface by using virtual NICs, (or whatever their name is in windows), and inspecting the traffic, same as if it was on a separate physical device, the drawing under "Virtual Setup" in the attached diagram show what I am trying to achieve. Reading a bit on the VirtualBox docs, seems like binding the right side is relatively simple, perhaps I should have one network adapter set as Bridge Networking and VirtualBox will connect it to the physical NIC on the host machine, and network packets are exchanged directly, circumventing the host operating system's network stack (WinXP in my case). However, I have no idea how to achieve the left side of my diagram, which requires adding virtual NICs to windows and configure them correctly in a way to make that pipeline possible. I would appreciate any help. by the way, if that is not possible with VirtualBox but with other virtualization solution (e.g. VMWare), I would accept the other as well.

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• Cannot access internet or remote network after connecting to Windows VPN

  - by Kiewic

  I set up a VPN by creating an incoming VPN connection (VPN server) in my Windows 8 machine at home (not a Windows Server). I forwarded the PPTP port in my router (port 1723) to this machine and enabled PPTP passthrough. In a second Windows 8 machine out of home, I created an outgoing VPN connection (VPN client). And I am able to connect to my home VPN, but I don't have access to any home resource or even internet. This is the output of the client ipconfig: And this are the settings of my VPN server: UPDATE: My VPN server has assigned the 192.168.1.144 IP adress at my home network. So, I tried setting the "IP address assignment" range from 192.168.1.150 to 192.168.1.200. And when a VPN client gets connected, it gets an address in that range, but it doesn't make any difference.

  Read the article

• Java website on Tomcat PHP website on Apache - how to get PHP web pages into Java web pages?

  - by Venkat

  We have a Java web application deployed on Tomcat. We also setup Apache and mod_proxy_ajp to route web requests (port 80/443) to Tomcat. We would like to deploy a PHP application on the same Apache server - probably under a subdirectory (/var/www/ourapp). Now we would like to access & display web pages from PHP application within web pages generated by Java application. Planning to implement Single Sign-on as well. Example: Web page from java has (JQuery Tabs) and we like to display the PHP web page within a tab while all other HTML comes from java application. Can you please give a overall picture of how to proceed about this? Mainly 1. how we should install/setup our PHP application on same Apache server which is used to route web requests to Tomcat? i.e. either setup sub domain or install in sub directory 2. How to bring PHP pages into present web pages (generated by java). Can we use AJAX requests or should go for Java PHP Bridge/ Querces such applications? Thank you for your time in advance. Regards.

  Read the article

• Trouble with resolving hostnames on CentOS using Bind

  - by cabaret

  I'm taking a course on server administration at school and I have managed to set up virtual hosting in apache and a dns server on a virtual machine. However, I have now set up an old pc to run CentOS and I'm trying the same on that box. The problem I ran into now is that I can't resolve hostnames from the linux box. I have set up the nameserver in /etc/resolv.conf to the IP of the CentOS machine, but when I try for example ping google.com I get ping: unknown host google.com However, when I do ping 66.102.13.105 (which is the Google IP, figured that out by pinging on my mac) I get: PING 66.102.13.105 (66.102.13.105) 56(84) bytes of data. 64 bytes from 66.102.13.105: icmp_seq=1 ttl=52 time=15.5 ms Slightly confused why this is happening. Could it be because of my router sitting in between the linux machine and the cable modem? It's a D-Link somethingsomething. Thanks in advance

  Read the article

• How to troubleshoot slow powerconnect 62xx management interface

  - by Hannes

  Our Dell Powerconnect 62xx switches have a very high packetloss on the management interface. I presume this is caused by a new appliance which uses multicast for communication but I am not sure. Our network setup is following: servers a - Dell PC6248 | servers b - Dell PC6248 |- juniper core router servers c - Dell PC6248 | What we see is that the multicast traffic arrives at all servers (but only the servers b use the multicast) and I fear that this multicast traffic floods the switch management interface. The switches' management interfaces are reachable via vlan101, all other traffic is sent over other vlans. When I tcpdump on one of the 2 servers with a vlan 101 ip address, I only get a few arp requests but almost nothing. When I try to ping between these 2 servers, it works like a charm. I would like to know what a good way is to troubleshoot this problem and maybe help me understand what is going wrong on that subnet.

  Read the article

• Cisco access list logging. Why is there a difference between IPv4 and IPv6?

  - by growse

  I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

  Read the article

• SSL Certificate for local web server

  - by Firefly

  Is it at all possible to create a self-signed certificate for use on multiple machines on a local network which would stop the browser complaining it is not a trusted site? We have a product which is basically a computer running lighttpd to serve a web interface for configuring the computer (sort of how a router has a web interface). There can also be many of these machines running on the same network with dynamic IP's. What I basically want to do is enable SSL for extra security but I don't want people who are on the local network to be given a browser warning about the certificate not being trusted. Is this at all possible?

  Read the article

• how can i realize a video-wall on 3-9pc with vlc

  - by Luca

  hello! i have to create a videowall, from 3 to 9 monitor. every monitor as a pc. actually, i stream from a server 9 movies with different istances of VLC, but i could also play on every machine the relative video with a single player. there's no problem. the real problem is that i really dont know how to sync the videos on a LAN...unfortunately there is a NETSYNC module inside VLC wich is NOT working. here are some info about my setup: videowall from 3 to 9 monitor || from 3 to 9 pc, all with the same configuration || a gigabit router+switch for the "dedicated" LAN im really stuck in this situation, if anyone has an idea or just a completely different solution, please, share it with me! thanks a lot in advance! :)

  Read the article

• once VPNed into pfSense, unable to hit the public URLs of my websites - they are routed to the pfSense box

  - by Sean

  I have a pfSense box setup as the firewall/router/VPN appliance at my colo. Once I VPN into the colo (either pptp or openvpn, pptp preferred due to multiple clients and ease of configuration), I am able to hit all my servers by their private 10.10.10.x ip and am able to browse the public internet without issue. When I try and hit the URL of a domain hosted by one of my servers, I am prompted for credentials. If I login using the pfSense credentials, I'm connected to pfSense as if I'd used it's internal IP. If I hack my hosts file to point url - server private IP it works fine, but this is obviously not a good solution. To recap: not connected to VPN - www.myurl.com works connected to VPN - www.myurl.com never makes it to the correct server, but is sent only to the pfSense box I'm sure it's something small that I've missed in the pfSense config.

  Read the article

• Airport Express configuration

  - by Christina

  We are trying to set up remote access to a computer that houses a server fro a particular program we are running. The program says we need to configure the office router. In the firewall settings it says to open ports 5345-5351 (TCP only). Port Forwarding: You will also need to forward the same range of ports (5345-5351) to the computer running the Server. This typically requires that the computer running the Server be assigned a static IP on the local network. Having trouble figuring out which IP address we actually need to be using on the client side of this program in order to access the server computer. Can someone walk through this process?? We are working on Mac OSX 10.5. Thank you in advance!

  Read the article

• Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

  - by Andrew Bolster

  I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

  Read the article

• Windows 8 doesn't automatically join Wi-Fi network if Ethernet connection is active

  - by Herb Caudill

  In Windows 7, my laptop would automatically join both an Ethernet network and the Wi-Fi network in my house (both going through the same router). In Windows 8, if the Ethernet connection is present, it doesn't join the Wi-Fi network at all. The reason I noticed this is that if Wi-Fi isn't active, I don't see my AirPlay speakers. My wireless printer is also unavailable until I manually connect to Wi-Fi. To recap: When I turn on my computer and it's connected to Ethernet, this is what my Network Connections control panel looks like: After I manually join my Wi-Fi network, it looks like this: I would prefer for it to join both networks automatically on startup, the way it did in Windows 7. Is there a way to make this happen?

  Read the article

• why this routing configuration does not work?

  - by avs099

  I have 2 VMs in HyperV role: first is RRAS - it has 2 interfaces (both manually configured, no DHCP): 192.168.1.110 - "external" one, connected to the router 192.168.10.2 - that's internal interface which other VMs will be using as well also I added VPN connection to our main server - and it gets 192.168.2.136 IP address in 192.168.2.XXX network. And IP route is create on the server as well for this interface. second VM is called KITCHENER. It only has 1 interface 192.168.10.99 / 255.255.255.0, with default gateway set to RRAS server - 192.168.10.2 QUESTION: how can I ping "main server" - 192.168.2.1 - from the KITCHENER server when RRAS server is connected to VPN? please see screenshots with ipconfig /all, route print and ping 192.168.2.1 commands. What needs to be done to get this working? all servers are Windows 2008 R2 if that matters.

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >