Search Results

Search found 124254 results on 4971 pages for 'ubuntu one api'.

Page 170/4971 | < Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >

• Attempting to dual boot Ubuntu and Windows 7 on Sony Vaio with Insyde H2O BIOS

  - by zach

  My situation is the same that is addressed here Sony VAIO with Insyde H2O EFI bios will not boot into GRUB EFI and here http://www.hackourlife.com/sony-vaio-with-insyde-h2o-efi-bios-ubuntu-12-04-dual-boot I tried to install Ubuntu 12.04 from the Live CD alongside my current Windows 7. I have to switch my BIOS to legacy mode in order to boot from CD. If I were to do a normal installation and remain in legacy mode, the BIOS will display "operating system not found". If I switch back then the BIOS just boots to windows. To solve the problem, I tried following the steps in the previous two articles. My drive is partitioned as: sda1 FAT32 Location of Windows EFI files (flagged as boot in Ubuntu install) sda2 unknown sda3 NFTS Windows C: sda4 ext4 Ubuntu root sda5 swap sda6 ext4 Ubuntu home I was a little confused by the requirement in the second article to "be careful to install Grub bootloader in /dev/sda3" In my case, the relevant partition is sda1. I have tried three things: setting the sda1 mount point as /boot, as /boot/efi, and as the special reserved grub partition. In each install I indicated that grub should be installed in sda1. After each install I reboot to the live CD and look in the sda1. I see EFI/Boot and EFI/Windows, but no EFI/Ubuntu and consequently no grubx64.efi. I understand the recommended procedure of moving grubx64.efi into the EFI/Boot directory and replacing the present bootx64.efi file, but I see no grubx64.efi and I don't know where it should be.

  Read the article

• Insufficient permissions within Eclipse when installed via synaptic in Ubuntu 12.04

  - by Clayton

  I installed Eclipse via the Synaptic Package Manager on Ubuntu 12.04 Desktop (more details on footer). However, from within Eclipse, I lack sufficient permissions to perform upgrades on my package and add-ons. I'm a recovering Windows user, and while I have a couple of years Ubuntu experience, I am unfamiliar with the command-line and mainly interact through the packaged GUI. Specifically, I am trying to install the upgrade for Eclipse CVS Clientorg.eclipse.cvs.feature.group1.3.100.v20110520-0800-7B78FHl9VF7BD7KBM4GP9C I am tracking the varying installation advice on a similar question eclipse install: Gaurav Butola Basically, the most current upgrades are available directly from eclipse?... But at some point I remember reading that the latest version of eclipse had been designed for the previous LTS of Ubuntu - I don't know if that is still true. I have read about the vulnerabilities of Java 6, and so I have gone with Open Java 7 openjdk-amd64 (if that has any relevance to which Eclipse package and installation method I choose). But I'm not crazy about the idea of creating a gksudo link in the sidebar launcher. I don't know enough about chown to use it - if that's even appropriate (I don't want stray java escaping from Eclipse and connecting to SkyNet). Another possible solution that I foresee is modifying my user's group memberships/privileges on the file system as a whole. The only other information that I think might be relevant is that I notice that Synaptic installed all of the files into /usr/ instead of /opt/ like I have seen recommended. So should I be changing ownership, reinstalling using a non-Synaptic method, or what? Any advice is greatly appreciated. Ubuntu information Ubuntu 12.04 LTS Memory 2.9 GiB Processor AMD Sempron(tm) Processor LE-1300 Graphics VESA: XXXXXXX OS type 64-bit Eclipse Version: 3.7.2 Build id: I20110613-1736 Ubuntu Developers :/usr/share$ ls -h -l drwxr-xr-x 5 root root 4.0K Sep 13 08:43 eclipse Install paths: /. /usr /usr/share ...

  Read the article

• Ubuntu 12.10 + Windows 7 - No option to install alongside windows 7

  - by user1828314

  I have a 64-bit Windows 7 OS installed at the moment. I have used GPartEd to shrink the current Windows 7 partition on my 720GB HDD to 200GB. I have then made a new NTFS partition of 200GB which I will keep for later on as a shared drive between both Windows 7 and Ubuntu. So in GPartEd I now have 3 partitions which were all automatically there from the Windows 7 installation, I only shrank the 3rd one from the 698GB or so that it was to 200GB and created the 200GB for the shared drive. I first tried creating another 200GB partition at this stage to install Ubuntu too but when I burnt the DVD and loaded it, Ubuntu gave me no option to install alongside Windows, only the option to erase the entire disk and install Ubuntu on the blank drive...not what I want to do. So I tried installing it through clicking 'Something else', it downloaded all the install files but didn't install. I then had a lot of problems with getting the DVD drive to work and what not but now have this fixed so I can use Windows again. So now I've used GPartEd to delete the partitions so again I'm now left with the 3 partitions there which Windows 7 automatically installs and a 200GB NTFS partition I will later use as a shared drive. Booting up from the Ubuntu disc and again there is no option to install alongside Windows 7. How do I get it to do so? All I would like is Windows 7 and Ubuntu on a dual boot, with a 200GB NTFS partition to dump my work onto so that I can access it from both OS's. Thanks.

  Read the article

• Can't boot Windows Xp after intalling Ubuntu 12.04

  - by Omul Neted

  Here's the situation. I installed Ubuntu using the along side option. Everything went ok. When I restarted I went strait to Ubuntu and it worked beautifully. When I restarted and tried to enter windows, the loading screen appeared, and after 3 -4 seconds it restarted again. No error, no cursor waiting, no nothing. I looked on the internet for help and found several resources. I tried first lilo since it seemes that many people had they're issues solved with it. After lilo neither ubuntu nor Windows would start. I installed and used bootinfoscript. The RESULTS.txt can be seen below https://www.dropbox.com/sh/r3luoa672qe73uq/Mob13HhNiB After that I looked at Boot-Repair I did as instructed here Can't boot XP after Ubuntu Installation, how to fix? ,meaning I redid the mbr of my Ubuntu install using a generic mbr. with no success. The results of boot-repair are in the first link. Now when I restart my computer I don't even get the windows loading screen, just Missing operating system Missing operation system Operating system not found that's it. I did not use the fixboot or fixmbr option because I don't have a windows cd cabable of seeing my hdd drivers. The usual XP windows setup tells me that I have no hdd. Please help, I don't know what to to next. This is my first time with Ubuntu or any Linux OS.

  Read the article

• Can't install Ubuntu on my Windows 7 laptop

  - by Ana

  I tried installing Ubuntu in two different ways: First, I tried the Windows Installer, and it goes well until I reboot the system and, when booting on Ubuntu, I get the error: No root file system defined. Second, I uninstalled wubi by going to to Control Panel - Uninstall Programs - Ubuntu. Then, I booted the laptop from the live CD and selected install. It boots okay but in the screen right after the one that says to make sure you have 4.5 GB available, Internet connection, etc, when I click continue it throws me a message saying that Ubuntu had an internal error and asks me if I want to report the error. After that, I just have a black screen and nothing else! No Ubuntu installed, no boot option to go back to Windows. Nothing! My goal is to install Ubuntu alongside Windows 7 (without the hassle of formatting the computer, creating partition, etc). How can I do it (preferable using Windows Installer)? How can I solve the "No root file system defined" that I encountered when I used the Windows Installer?

  Read the article

• Ubuntu 12.10 boots to purple or black screen but intermittently boots fine

  - by Nic

  I have a fresh install of Ubuntu 12.10 64bit dual booting with Win7 64bit. Windows boots fine every time. When I choose Ubuntu from Grub2 menu it will sometimes boot just fine. Most of the times though it gets stuck at a purple screen with nothing happening and no keys or key combinations working. Other times instead of the purple screen I get a black screen with a flashing cursor at the top. Nothing happens. I need to hold down the power button to restart and after a couple times of trying it will eventually boot into Ubuntu. Once that happens everything runs without any problems. I have tried different approaches to fix the problem but to no avail. I tried removing "quiet splash", used no splash, and nomodeset What I got from this was seeing all the text of the boot process but more often than not the process gets stuck right after recognizing all the USB ports and devices. If it gets stuck nothing happens (except when i plug in a usb device: it still recognizes it with a new line of text) In the case when the boot process works, after it lists the usb devices it tells me something like: recovery of read-only filesystem necessary. (its the filesystem that ubuntu runs on) then it does the recovery and i get: recovery complete. after that Ubuntu will boot properly and I get to see the login screen. I have no idea what to do to fix that problem. I have to reboot 3 to 5 times everytime I want to get into Ubuntu and I feel like I'm breaking my new Laptop. (its a lenovo ideapad z580 btw. i5 processor and nvidia gtx640 graphics card) I hope someone can help me. Thanks. Edit: i just got a "failed to enable AA error" message when waking it up from suspend. I don't know if that helps or has anything to do with the boot probs.

  Read the article

• Ubuntu installation on iMac

  - by Shanew

  I have an iMac configured as follows - Screen 27" CPU 3.4 GHz i7 Graphics AMD Radeon HD 6970 1024 MB I downloaded Ubuntu version 11.10 64 bit ISO and burnt that to both DVD and USB stick as per the instructions on Ubuntu's download page. Neither will boot. Symptoms are as follows - DVD: When the iMac is restarted and booted from DVD (labelled Windows which isn't mentioned in Ubuntu's website instructions) one line is displayed against a black screen displaying a message about the developer and date. After 5 minutes the message hangs and the DVD ceases to spin. USB Stick: Strangely I have to select the EFI boot CD icon which appears after holding down the Alt key. A text menu appears offering me to try Ubuntu without installing. I select this and the screen goes blank and stays blank. Any ideas? Lastly, after writing Ubuntu to DVD and USB stick, neither could be read by OSX making the instructions to eject them as per Ubuntu website's instructions useless. This might help? Thanks, Shane.

  Read the article

• Problem with XeTeX (LaTeX) and system fonts

  - by mghg

  I have started to use an enterprise specific class for LaTeX, but have got a problem with usage system fonts in Ubuntu. The class uses the fontspec package, I have therefore been instructed to use XeTeX (i.e. the command xelatex instead of latex or pdflatex). However, the command xelatex testfile.tex results in the following message: ! Package xkeyval Error: `TeX' undefined in families `Ligatures'. See the xkeyval package documentation for explanation. Type H <return> for immediate help. ... l.61 \newfontfamily\headfont{Arial} ? The class has previously been used on Mac and Windows and the font setup is as follows: \newfontfamily\headfont{Arial} \newcommand\texthead[1]{\headfont #1} \setromanfont{Georgia} \setmainfont{Georgia} \setsansfont[Scale=MatchLowercase]{Verdana} It has been suggested that since XeTeX makes use of system fonts and the class file has worked flawlessly on Mac and Windows, the problem might be that Arial is not a name used in Ubuntu. I have tried to exchange Arial with Ubuntu Light in the setup code above, but that have not been any improvement. Any suggestions please on how to move forward?

  Read the article

• Remap keyboard Ubuntu 12.04; Asus Q500A

  - by hydroxide

  I have an Asus Q500A with win8 and Ubuntu 12.04 64 bit; linux kernel 3.8.0-32-generic. I am using gnome-panel, and xserver-xorg-lts-raring. I have been experiencing problems with the keyboard short-cuts since I had a fresh install. fn+f10 is supposed to mute my system, but instead it will repeatedly press d. fn+f11 is volume down, but it presses c. fn+f12 is volume up, presses b repeatedly. Most of the other on-board short-cuts such as adjusting screen and led brightness work most of the time, but sometimes press other letters repeatedly. Also, sometimes my cntr gets held down for no reason. Everything works fine in windows. I have tried installing all recommends and sudo dpkg-reconfigure -a to reconfigure all packages, which did not solve my problem. I have tried using KeyTouch editor to edit keymaps, navigating to /usr/shar/x11/xkb/keymap when I try opening any of these files it says file contains no keyboard element. I think If I were just able to remap my keyboard it might solve my issues, otherwise if anyone knows where I can get asus drivers for 12.04 please let me know Apparently I didn't have all repositories enabled. I executed the following commands and am trying the updates they give me. Getting linux_kernel 3.8.0-33 generic as well as a bunch of other packages. sudo add-apt-repository "deb http://archive.ubuntu.com/ubuntu $(lsb_release -sc) universe" sudo add-apt-repository "deb http://archive.ubuntu.com/ubuntu $(lsb_release -sc) main universe restricted multiverse" sudo add-apt-repository "deb http://archive.canonical.com/ubuntu $(lsb_release -sc) partner"

  Read the article

• What is the need for 'discoverability' in a REST API when the clients are not advanced enough to make use of it anyway?

  - by aditya menon

  The various talks I have watched and tutorials I scanned on REST seem to stress something called 'discoverability'. To my limited understanding, the term seems to mean that a client should be able to go to http://URL - and automatically get a list of things it can do. What I am having trouble understanding - is that 'software clients' are not human beings. They are just programs that do not have the intuitive knowledge to understand what exactly to do with the links provided. Only people can go to a website and make sense of the text and links presented and act on it. So what is the point of discoverability, when the client code that accesses such discoverable URLs cannot actually do anything with it, unless the human developer of the client actually experiments with the resources presented? This looks like the exact same thing as defining the set of available functions in a Documentation manual, just from a different direction and actually involving more work for the developer. Why is this second approach of pre-defining what can be done in a document external to the actual REST resources, considered inferior?

  Read the article

• no aparece grub con gpt windows/ubuntu

  - by user100604

  I have an asus k55VM. The problem is that once done the partitions to install windows 7 finalize you and then ubuntu 12.10 the grub not to appear. On having created the table of partitions with gparted I did it in format msdos but then on having installed windows gently accepted me and he says to me that I must do it with format gpt therefore I erase the disc in the assistant of installation and believe a partition of 160 gb Later between with live CD to ubuntu and believe other partitions between which, one ext4 for ubuntu... I install and restart. On having restarted the grub does not go out but if the partitions appear of windows. To seeing if someone helps me am desperate. Thank you very much Tengo un asus k55VM. El problema es que una vez hechas las particiones instalar windows 7 ultimate y luego ubuntu 12.10 no aparece el grub. Al crear la tabla de particiones con gparted lo hice en formato msdos pero luego al instalar windows no me acepta y me dice que debo hacerlo con formato gpt por lo tanto borro el disco en el asistente de instalacion y creo una particion de 160 gb Posteriormente entre con live cd a ubuntu y creo otras particiones entre las cuales, un ext4 para ubuntu... Instalo y reinicio. Al reiniciar no sale el grub pero si aparecen las particiones de windows. A ver si alguien me ayuda estoy desesperado. Muchas gracias

  Read the article

• How to restore Windows7 after restore ubuntu bootloader?

  - by Mateusz Rogulski

  At first I will describe my situation in a few points: I have installed Windows7, and then Ubuntu 11.04 on my machine. Then everything works fine and at start of system I have screen from linux where I can choose the system. Then I reinstall Windows7 and install Windows 8 on other partition. Then I can choose between Win7 and win8 when I start system. Then I need my Ubuntu back so I want restore my bootloader from Ubuntu. I boot Ubuntu from USB and in terminal write this commands: sudo fdisk -l Then I get: /dev/sda1 1 13 104391 de Dell Utility /dev/sda2 14 2805 22425601 5 Rozszerzona /dev/sda3 * 2805 41968 314572800 7 HPFS/NTFS /dev/sda4 41968 60802 151282688 7 HPFS/NTFS /dev/sda5 14 2445 19530752 83 Linux /dev/sda6 2445 2805 2893824 82 Linux swap / Solaris Next commands: sudo mount /dev/sda5 /mnt sudo mount --bind /dev /mnt/dev sudo mount --bind /proc /mnt/proc sudo chroot /mnt grub-install /dev/sda I get Installation finished. No error reported.. And when I start my machine I have old Ubuntu start screen to choose system. Ubuntu works well. But There are no Windows 8 option. But my primary problem is when I choose Windows 7 I have: error: no such device ... error: no such disk so I have no idea what can I do. I really need both systems to work. Any help would be appreciated.

  Read the article

• Ubuntu doesn't boot due to GRUB-Problems

  - by Dave

  Users out there, I came here with the spark of a hope, that you could help me. I want to get rid of my old WinXP, because the Game-Support for it seems to slowly expire now... So I took a second drive, just an old empty one I had at hands (ATA-Maxtor 90648D3), plugged of the other drive with WinXP, so that it couldn't be harmed, and started the installationof Ubuntu 12.04. Everything went as it was supposed to, until the end. Normal shutdown after successful installation process. But when I tried to boot my new Ubuntu from the HDD, it said: error: out of disk. grub rescue> So, what to do now? I already tried a lot of things in the terminal, e.g. the update-grub as mentioned on http://opensource-sidh.blogspot.de/2011/06/recover-grub-live-ubuntu-cd-pendrive.html. Everything worked, he didn't complain about a missing data or anything, but at the end of the day he still wasn't able to boot! Next step was to change the etc/default/grub-file, so that it could load the ATA-drivers first, so that there is now problem with my drive. But even this didn't seem to have any effect, I'm still stuck with Ubuntu in the Live-CD-Mode... If there was anybody to help me out there, I would be very glad. Thanks for any support, Dave P.S.: I even tried to fix it with boot-repair, a small tool for Ubuntu, and it created a file with data that could probably help you to help me. You can find it on http://paste.ubuntu.com/1428022/

  Read the article

• Ubuntu installer does not show drives

  - by Tanweer Rashid

  I am trying to install Ubuntu 12.04 LTS on my Inspiron laptio, but the installer does not show any drives. My system has a 1TB SATA drive and a 32GB SSD. As far as I can figure, the boot files are kept on the SSD for fast startup (for Windows). During Win7 installation, I had to manually load drivers for RAID controller to see all available drives. Running fdisk -l from the live CD shows the following: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b4782 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 81920 41627647 20772864 7 HPFS/NTFS/exFAT /dev/sda3 41627648 357019647 157696000 7 HPFS/NTFS/exFAT /dev/sda4 357019648 1953517567 798248960 f W95 Ext'd (LBA) /dev/sda5 672415744 1312966655 320275456 7 HPFS/NTFS/exFAT /dev/sda6 1312968704 1953517567 320274432 7 HPFS/NTFS/exFAT Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b474b Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive ubuntu@ubuntu:~$ In the Ubuntu installer, I can only choose /dev/sdb for "Device for boot loader installation", and sdb doesn't show any drives. I cannot select /dev/sda. Any ideas anyone? Thanks.

  Read the article

• Fresh install of Ubuntu 12.10 won't boot on Asus X101CH Eee PC

  - by Najdmie

  I did a fresh install of Ubuntu 12.10 in my Asus X101CH Eee PC, using a live usb which I made using startup disk creator, replacing Ubuntu 12.04. The installation ran smoothly, but when I boot, it goes to a purple screen for a second, then a lot of text like the following shows up in sequence: Starting crash report submission daemon [OK] Starting CPU interrupts balancing daemon [OK] Stopping save kernel messages [OK] _ And the cursor just keeps blinking for hours. I can't log in. Pressing Alt + F2 did not bring me to console mode. I thought it might be a partition problem so I formatted the whole disk, by creating a new partition table using gparted in Ubuntu 12.04 live USB. I noticed that I can't try Ubuntu using 12.10 live USB either; it just went to a blank screen when I hit the 'try ubuntu' button. But the same problem arose. I even changed the pen drive for the live USB a couple of times. I happened to know that the Intel Atom N2600 Cedar Trail CPU in my computer is not well supported in Linux, I managed to install its drivers in Ubuntu 12.04, although the computer went blank during the installation.

  Read the article

• I have deleted python files in usr/bin and cant reinstall it

  - by Plonkaa

  I am a novice at Ubuntu and unfortunately i have deleted 3 files in the usr/bin folder python 2.7 python python 2.6 Now my update manager wont work and when i type in python into gnome it says that it is no longer there. Please help me ive tried loads of different things but it just wont work. The closest i got was the following: I typed in sudo apt-get -f install and i thought i had fixed it but then i got a error message - Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: gir1.2-folks-0.6 gir1.2-polkit-1.0 libcogl5 mutter-common gir1.2-json-1.0 libcaribou0 gir1.2-accountsservice-1.0 gir1.2-clutter-1.0 gir1.2-gkbd-3.0 gir1.2-networkmanager-1.0 caribou libcogl-common libmutter0 gir1.2-mutter-3.0 gjs gir1.2-caribou-1.0 libclutter-1.0-0 gir1.2-telepathylogger-0.2 libclutter-1.0-common cups-pk-helper gir1.2-upowerglib-1.0 gir1.2-cogl-1.0 libmozjs185-1.0 gir1.2-telepathyglib-0.12 gir1.2-gee-1.0 libgjs0c gnome-shell-common Use 'apt-get autoremove' to remove them. The following extra packages will be installed: ubuntu-sso-client The following packages will be upgraded: ubuntu-sso-client 1 upgraded, 0 newly installed, 0 to remove and 35 not upgraded. 2 not fully installed or removed. Need to get 0 B/57.7 kB of archives. After this operation, 16.4 kB of additional disk space will be used. Do you want to continue [Y/n]? y Setting up python-minimal (2.7.2-7ubuntu2) ... /var/lib/dpkg/info/python-minimal.postinst: 4: python2.7: not found dpkg: error processing python-minimal (--configure): subprocess installed post-installation script returned error exit status 127 Errors were encountered while processing: python-minimal E: Sub-process /usr/bin/dpkg returned an error code (1) any advice is appreciated!

  Read the article

• How is the Ubuntu installation supposed to work?

  - by Bob D

  I have given up on installing Ubuntu 12.04.01 for the sixth time. I finally got Windows XP to work again. So I blitzted the Ubuntu partition and the swap partition and was about to install the sixth try when it occurred to me that ought to ask how is is "supposed" to go. My installer will install Ubuntu on the Linus ext4 partition I created by hand in Windows on my C drive. But the installer keeps insisting on installing the OS on my D drive unless I intervene. So if I choose "do something else" it will accept installing Ubuntu on the C drive in the partition I previously created, but it insists on putting the "Device for boot loader installation" on the D drive. I can select a different drive at this point (where I could not with the "along side windows choice) but what drive to I choose??? It lists sda, sda1, sda5, sdb and sdb1. The five times before this all ended in disaster letting the installer choose. So I need human intervention. Where is the safe place to do this. The results from the previous attempts left me with only the Ubuntu that would boot, the boot to windows from the grub menu failed every time. Is there a better version of Ubuntu I can use? Is V12.04.01 messed up? My goal is still to use Wine on it to run PC programs. I would like to find a shell or skin or something that makes it seem like windows but have the security and power of Linux under the good. I have seen this type of system and it worked very well. I know I am getting long winded but I have been though at least four of the seven rings of hell already, so I want this install to be the last.

  Read the article

• How to define template directives (from an API perspective)?

  - by Ralph

  Preface I'm writing a template language (don't bother trying to talk me out of it), and in it, there are two kinds of user-extensible nodes. TemplateTags and TemplateDirectives. A TemplateTag closely relates to an HTML tag -- it might look something like div(class="green") { "content" } And it'll be rendered as <div class="green">content</div> i.e., it takes a bunch of attributes, plus some content, and spits out some HTML. TemplateDirectives are a little more complicated. They can be things like for loops, ifs, includes, and other such things. They look a lot like a TemplateTag, but they need to be processed differently. For example, @for($i in $items) { div(class="green") { $i } } Would loop over $items and output the content with the variable $i substituted in each time. So.... I'm trying to decide on a way to define these directives now. Template Tags The TemplateTags are pretty easy to write. They look something like this: [TemplateTag] static string div(string content = null, object attrs = null) { return HtmlTag("div", content, attrs); } Where content gets the stuff between the curly braces (pre-rendered if there are variables in it and such), and attrs is either a Dictionary<string,object> of attributes, or an anonymous type used like a dictionary. It just returns the HTML which gets plunked into its place. Simple! You can write tags in basically 1 line. Template Directives The way I've defined them now looks like this: [TemplateDirective] static string @for(string @params, string content) { var tokens = Regex.Split(@params, @"\sin\s").Select(s => s.Trim()).ToArray(); string itemName = tokens[0].Substring(1); string enumName = tokens[1].Substring(1); var enumerable = data[enumName] as IEnumerable; var sb = new StringBuilder(); var template = new Template(content); foreach (var item in enumerable) { var templateVars = new Dictionary<string, object>(data) { { itemName, item } }; sb.Append(template.Render(templateVars)); } return sb.ToString(); } (Working example). Basically, the stuff between the ( and ) is not split into arguments automatically (like the template tags do), and the content isn't pre-rendered either. The reason it isn't pre-rendered is because you might want to add or remove some template variables or something first. In this case, we add the $i variable to the template variables, var templateVars = new Dictionary<string, object>(data) { { itemName, item } }; And then render the content manually, sb.Append(template.Render(templateVars)); Question I'm wondering if this is the best approach to defining custom Template Directives. I want to make it as easy as possible. What if the user doesn't know how to render templates, or doesn't know that he's supposed to? Maybe I should pass in a Template instance pre-filled with the content instead? Or maybe only let him tamper w/ the template variables, and then automatically render the content at the end? OTOH, for things like "if" if the condition fails, then the template wouldn't need to be rendered at all. So there's a lot of flexibility I need to allow in here. Thoughts?

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• Boot ubuntu 12.04 in 3D - nomodeset quiet splash install

  - by rahi

  I would like to enable 3D in Ubuntu 12.04. I recently tried to install ubuntu on a new computer. When the installation was complete and I rebooted the machine, I could only see a blank screen. After some searching, I followed this tutorial which instructed me to boot with "nomodeset" enabled. I choose this on the USB I was installing ubuntu 12.04 from. Fortunately, the ubuntu installation on the new computer was successful. When I tried to change the size of the unity launcher icons, I did not see that option (as I see on my other computer running ubuntu 12.04). I tried installing MyUnity and it told me that the computer I had just installed 12.04 to was running in 2D. To my knowledge. all the software is up to date (as I ran the Software Updater). In addition, when I look for Additional Drivers, I see a message that says "No proprietary drivers are in use on this system". When I look under System Details Graphics, I see the Driver as "VESA:Intel Sandybridge/Ivybridge Graphics. When I hold the shift key on when my machine boots up, and type "e" on the Grub menu, I see the following towards the end, "nomodeset quiet splash $vt_handoff". Does this have anything to do with the plain 2D ubuntu 12.04 experience? Again, what I'd like to do now is get the 3D experience on my new machine running 12.04. Please let me know if you need more information.

  Read the article

• how to create a mirror of minimum size to install Ubuntu

  - by Registered User

  I need to create an http url at my laptop to have a Ubuntu installation begin within my laptop on a Xen environment. This is how the final thing will look like http://bderzhavets.wordpress.com/2008/10/28/install-ubuntu-intrepid-server-pv-domu-at-xen-33-port-via-httpgetco-centos-52-dom0/ the host and client are both going to be my laptop, I Google d and came across apt-mirror and some other packages. I do not want to archive entire 15 GB Ubuntu repositories on my machine. It is not possible to use a CD,ISO,loop mounted disk (reason mentioned below). I have tried using netboot image on local machine which failed because if you are attempting to create a virtual machine on a hardware which does not support VT virt-manager installer necessarily needs a URL of this sort http://archive.ubuntu.com/ubuntu/dists/hardy/main/installer-i386/current/images/netboot/ any other option to create guest OS is simply grayed out. The unfortunate part is my Ethernet connections do not work when I boot with Xen-4.0 and a pv-ops Dom0 kernel from Jeremy's tree.Which is where I have to do this work.So I have to create a URL structure which is similar to Ubuntu mirrors.So how can I do this in bare minimum so that at least the console boots and once the console comes I can do some work.

  Read the article

• How do I make my volume indicator operate in decibels instead of percentage?

  - by ethana2

  When I want to adjust the volume of anything I'm doing, I find that using the volume controls built into Ubuntu is little but confusion. When the volume is around 100%, dropping it several increments has almost no effect on apparent volume, but when it's around 0%, the effect of one click of my mouse wheel is probably a good 3 decibels. I have observed this behavior on tens of different UC's, since I convert about one Ubuntu user a month (NE team contact). This has proven so frustrating to me that I tend to use the volume knob on my guitar amp ( mono audio :| ) instead of the volume indicator. What can I do to make my volume indicator behave properly until this is fixed? I want each volume increment to be one half or one third decibel. Is there a different piece of software I should use for system volume configuration perhaps?

  Read the article

• Strange resizing of partition after reinstalling Ubuntu 14.04 64bit

  - by Mike

  I started with Windows 7 on 120GB SSD and Ubuntu 14.04 32bit installed on 60GB partition on separate 1TB HDD. I just did a fresh reinstall of 14.04 64bit on the 1TB HDD. In the installation set up process, I selected the second choice of "deleting Ubuntu 14.04 and all it's files,documents, photos etc and reinstalling" to what I figured would reinstall the 64bit OS on the already existing 60GB allocated partition. Instead, it reinstalled Ubuntu as 43.5 GB and created a separate 15.8 partition. So now it reads that my disk space for Ubuntu ( in settingsdetails) is 43.5GB (instead of the previous 60GB that my old 32bit had) The upside is I can now access my 1TB HDD from my toolbar(and all the files located on it) Before, I could only access that through Windows (I can also access the SSD too, but that was always the case) Both drives are mounted now. My initial reaction was to go into Windows 7 disk management delete the strange/new 15gb partitionextend the 43.5 to the unallocated space. But I'm not sure if this is necessary or would even work. My question is why did it create a 15gb partition shrinking my ubuntu disk space, and is it useful? I don't want wasted space, so before I go through all my set up of Ubuntu, should I change this. At this time my HDD reads as 43.5 partiton, 15.8 partition, and 874GB exfat32 (939GB total)

  Read the article

• Ubuntu One has high CPU usage but no syncing

  - by Peter

  over the weekend I updated my computer to Windows 8. So far Ubuntu One was running smoothly, but ever since the update (clean, new install) Ubuntu doesn't sync any more. In Windows 7 it would start to sync at full internet speed as soon as I drop a file. But now in Windows 8, as soon as I drop a new file into the Ubuntu One folder, CPU usage goes up to about 50 % and no network traffic occurs. This stays like that for a couple of minutes, CPU usage goes back to normal and then the client says that all is in sync - which isn't true. Is it too early for Windows 8? Do others have the same problem or is there something I can do about it? I try a couple of different things, and realized that if the file size is 20 MB the files get uploaded. The original file was 1.5 GB. I also didn't work with 200, 100 and 50 MB large files. But even with 20 MB large files, the upload is very slow and not steady. The log give plenty of this error: - twisted - ERROR - Failure: exceptions.TypeError About which I don't know the meaning. By the way, the account works just fine on the Ubuntu 12.04 partition. Any help is greatly appreciated. -Peter

  Read the article

• What subject do you discuss with your manager during a one-on-one?

  - by Martin

  Every week, I have a 30 minutes meeting scheduled with my manager to talk about pretty much anything. So far, I haven't taken those one-on-one very seriously. As a new year resolution, I would like to take more seriously my one-on-ones with my manager. One way I though I could do that is to plan in advance (come up with a list of questions and/or agenda) my one-on-one. With the exception of the status report, what subject do you discuss with your manager during a one-on-one? Have you ever seen an agenda for one-on-one?

  Read the article

< Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >