Search Results

Search found 5859 results on 235 pages for 'driver'.

Page 178/235 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• wine 1.4 regedit makes screen flicker on 12.04 with dual monitor setup

  - by s1lv3r

  I have a dualmonitor setup running dual 23" on 1920x1080 which has the following problem: When running any wine application (for example "wine regedit" from console) the screen flickers and the windows have artifacts like this: Also sometimes taking a screenshot using the print key will make compiz crash (starter and all window bars/menus are gone) when an wine application is started. I don't have the same problems on my notebook which has the same setup. Only difference is the notebook has ATI Graphics and this PC has nvidia. This is the output of lshw -c video: *-display Beschreibung: VGA compatible controller Produkt: G72 [GeForce 7300 LE] Hersteller: NVIDIA Corporation Physische ID: 0 Bus-Informationen: pci@0000:07:00.0 Version: a1 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress vga_controller bus_master cap_list rom Konfiguration: driver=nvidia latency=0 Ressourcen: irq:16 memory:fa000000-faffffff memory:d0000000-dfffffff memory:fb000000-fbffffff memory:fce00000-fce1ffff I also noticed that running xrandr from console makes the screen flicker for some seconds on this PC, which also doesn't happen on my notebook. Removing one screen from the setup will stop the flickering and the artifacts inside the wine applications from appearing. Does anybody have an advice what I could try to change to make this work?

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• When running a .jar application with OpenJDK, my keyboard becomes unresponsive?

  - by Mochan

  I recently downloaded a Java application with the .jar format, and had it running on my computer not so long ago. Now that I'm using my desktop instead of laptop temporarily, I want it to run. On my laptop it was a tremendous hassle to get OpenJDK to even run the application without it going black, and now on my desktop I don't have that problem. However, when I run the application, my keyboard becomes unresponsive and doesn't type at all. This is a really big problem because it's demands the use of a keyboard. It works as normal on my laptop though, and it works perfectly. But now on the desktop its completely useless. I don't know if there's like a keyboard driver I'm missing, but there shouldn't be because the keyboard runs flawlessly everywhere else. I'm using OpenJDK 6 because the 7 has the same 'black screen' I mentioned, so I need this to work within OpenJDK 6. Thanks so much in advance and I'll try to specify as many details as I can. M

  Read the article

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• No Wireless In Ubuntu 13.10

  - by viktorhubinette

  When I upgraded to Ubuntu 13.10, I can't connect to wireless. The only thing I can connect to is ethernet, so please help me, What should I do? Here is the output of the lspci -nnk | grep -i net -A2 00:19.0 ethernet controller [0200]:intel corporation 82579V Gigabit network connection [8086:1503] (rev 04) subsystem: acer incorporated [ALI Device] [1025:8000] Kernel driver in use : e100e output of lsusb: Bus 002 Device 003: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:0152 Realtek Semiconductor Corp. Mass Storage Device Bus 001 Device 040: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 004: ID 0bda:8178 Realtek Semiconductor Corp. RTL8192CU 802.11n WLAN Adapter Bus 003 Device 003: ID 045e:070f Microsoft Corp. Bus 003 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• 12.04 GPU lockup

  - by soandos

  I was able to install Ubuntu 12.04 using the alternative version of the image, (64 bit) but when I start the system it tells me the GPU locked up, and instead presents a text only screen. I understand that this site is not for bug reports, but at the same time, I know that there are some versions of the installer than have to be compatible with my graphics card (Nvidia GTS 360M). I assumed that the mere fact that the alternative installer ran was an indication that I could get some sort of graphical interface running after the install. Is there some way of getting some type of graphical interface running on my machine? Even better would be is there a way to get the rest of the system running as normal (i.e. GPU up and running)? If an internet connection is required to download driver support or something similar, directions for how to configure a wireless connection with WPA2-Personal protection from the text-only interface (bash). Any help would be appreciated. Note: I was able to find this which tells me that the card is supported. Note 2: In the install software stage of the install, I was unable to install anything (no internet connection) Update: The exact error message is [8.591394] [drm] 0000:01:00.0: GPU Lockup - switching to software fbcon Update 2: If I try to install with the regular version of Ubuntu, the screen goes staticy. This also happens if I install with Wubi (distasteful I know) and then try to use Ubuntu. Update 3: I've tried xforcevesa, nomodeset and xforcevesa nomodeset as my wubi boot options. Update 4: Thanks to jokerdino, I can now connect to the internet, so internet tools would now be a possibility.

  Read the article

• Can't connect to hidden network with BCM4313

  - by poomerang

  The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• How do I get Graphics drivers / bluetooth / card reader working on an Acer Aspire V3-571G?

  - by Adam

  A couple of days ago I bought an Acer Aspire V3-571G laptop without a system installed on it. The only thing that was there was Linux Linpus. I created a bootable CD with Ubuntu 12.04 64-bit - I read that my processor was 64 bit and that it might be a good configuration for my gear (I'm not especially fluent with all the computer stuff, still trying to learn) and replaced Linpus with Ubuntu. Everything seemed to work fine, but there're few exceptions to that which came pass my way. My bluetooth doesn't work. It seems to be switched on, but when I check my system settings the button is actually off, and I can't drag it 'perminently' to the 'on' position. Tried a couple of commands I found on the net, none of them helped and there was no word whatsoever in my BIOS settings about enabling bluetooth. My card reader has some serious problems with copying more than one file at a time. I tried to put some music on my phone through a MicroSD card adapter (because my bluetooth doesn't work) and it got stuck every single time I copied an album on it. I'm not sure if all my drivers were properly installed, so I checked in the terminal if it could tell me sth about my graphics. typed: sudo lshw -c display and what i got was: *-display UNCLAIMED description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller cap_list configuration: latency=0 resources: memory:b2000000-b2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) *-display description: VGA compatible controller product: Ivy Bridge Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:b3000000-b33fffff memory:c0000000-cfffffff ioport:3000(size=64) As I said I'm no expert and not english-speaking generally, but it doesn't seem to be right. I've got a NVIDIA GeForce GT 640M.

  Read the article

• Internal Mic not working on Dell Adamo 13

  - by AFD

  So I'm using Elementary Luna Beta (based on Ubuntu 12.04 LTS) on a spare HDD after successfully using Jupiter release (based on 10.10) for many years. In Jupiter I had my internal mic work out of the box and with Skype installed from deb it was all setup without having to step foot inside the terminal. In Luna Beta the internal mic is not recognised by the OS and so also not recognised by Skype. I believe the hardware is this (from sudo lshw): *-multimedia description: Audio device product: 82801I (ICH9 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:46 memory:f8600000-f8603fff As well as this I ran cat /proc/asound/card0/codec* | grep Codec which gave me: Codec: IDT 92HD73C1X5 Codec: Intel Cantiga HDMI How do I tweak Luna to get this hardware working properly? I'm able to switch out my Luna HDD with the Jupiter HDD to help troubleshoot what the differences are between the two and why the more recent OS can't find / use the mic correctly. Thanks in advance for any help you can give.

  Read the article

• How do I fix a garbled screen on a Gateway LT3103u?

  - by paracaudex

  I've been having garbled screen problems on a Gateway LT3103u on Ubuntu for a while. I just did a fresh install of Ubuntu 11.10 and continue to have issues. I installed xubuntu-desktop in case the issues had to do with the sophisticated GNOME graphics. The problem is less bad, but it's still there. After a few minutes of using XFCE, the screen gets garbled. I assume this has something to do with the graphics card, but I don't know how to go about troubleshooting something like this. Where should I start? Update: Here is the description of the VGA card from lspci -vvv: 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] (prog-if 00 [VGA controller]) Subsystem: Acer Incorporated [ALI] Device 028c Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- [disabled] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Kernel driver in use: radeon Kernel modules: radeon Update: Setting GRUB_CMDLINE_LINUX="nomodeset" in /etc/default/grub seems to have fixed it in both Ubuntu and xubuntu-desktop. I will test it for a day or so to see if the problems recur and then post more detail with some links to an explanation. Update 2: It is possible to use this fix for Nvidia card (GTX 260) when graphics is defective after 11.10 upgrade/install? First few restarts was graphic ok, then after few restarts begins suddenly be defective and it stay so. I must returned to 11.04 because this problem and I wait for 12.04. So I hope in this fix.

  Read the article

• Slow USB 3.0 speeds

  - by Cygnus X

  Long time forum forager, first time poster. I bought a Toshiba 500 GB usb 3.0 hard drive last week and instantly ran home to see how fast I could push it. On my desktop (that I built) I was able to get 200 MB/sec. On my laptop (MSI FX something or other), which I dual boot Windows 7/Ubuntu 11.10, I was able to get about 120 MB/sec on Windows, but on Ubuntu, i get about 25 MB/sec. lsusb shows: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 0bda:0139 Realtek Semiconductor Corp. Bus 002 Device 003: ID 1532:0015 Razer USA, Ltd Bus 004 Device 002: ID 0480:a007 Toshiba America Info. Systems, Inc. lspci -vvv shows that the USB 3.0 host controller is using the kernel driver in use is xhci_hcd. dmesg |grep usb shows: [ 1815.455368] usb 4-1: new SuperSpeed USB device number 2 using xhci_hcd [ 1815.475459] scsi7 : usb-storage 4-1:1.0 The built in disk utility says its connected via usb at 705 MB/s, but that's not what it reports when I transfer files over to it. Not really sure what to do at this point. Any help would be very nice, thank you.

  Read the article

• Synaptics drivers are not loading on Kubuntu 13.10 on Dell Vostro 2420

  - by Alok Singh Mahor

  I freshly installed Kubuntu 13.10, 32 bit version on newly purchased Dell Vostro 2420. everything is working fine except scrolling and multitouch features through touchpad. I am able to change position of cursor using touchpad and able to tap (single click and double click) but scrolling is not working I tried to find out solution by searching on google but could not find proper solution to load synaptics drivers. i am listing some details: Laptop: Dell Vostro 2420 Linux Kernel version and distribution: 3.11.0-12-generic, Kubuntu 13.10 output of xinput list is ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Generic Mouse id=12 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Power Button id=8 [slave keyboard (3)] ? Sleep Button id=9 [slave keyboard (3)] ? Laptop_Integrated_Webcam_HD id=10 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=11 [slave keyboard (3)] ? Dell WMI hotkeys id=13 [slave keyboard (3)] Output of synclient -l is Couldn't find synaptics properties. No synaptics driver loaded? output of lshw is at http://paste.ubuntu.com/6645687/ xserver log and dmesg dont have trace of synaptics kindly tell me how to troubleshoot this problem.

  Read the article

• 12.0.4.3 - Missing Battery Icon, auto Suspend not working, Keyboard shortcuts volume up/down no longer working

  - by Navraj

  Problems I am experiencing: Battery Icon not showing up unity bar (top right corner). Volume Up/Down/Mute not working. Bluetooth hot keys described above also not working.Brightness up/down keys on this keyboard no longer working (apple wireless keyboard) Laptop no longer suspends when lid is shut. I have to go to 'power' button on top right corner and click on 'Suspend' All was working flawlessly until I did the following: I have recently upgraded to Nvidia propriety driver version 319 {version recommended}. Installed Xscreensaver and then removed it and went back to default screensaver. Done a system update (1st since installing) and now currently running: Linux 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:19:35 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux NOTE: Base system was ubuntu 12.04.3 installed from ISO however lsb_release reports "No LSB modules are available" 4.installed psensor. I have check power setting (via Settings) and power setting via dconf-editor and set to recommended settings as described in posts detailing solution to this problem. - I have disabled 1) Nvdia settings at startup and 2) psensor at startup but this does not help. I am using an HP DV7 with 2GB Nvidia card. Not using any fancy graphics features. Recommendations? Thanks.

  Read the article

• USB device is recognized but has no address

  - by SeanMG

  Good day folks, I'm trying to use a USRP1 with GNURadio if anyone knows what any of that is. I am running Ubuntu on a Windows 7 machine via VMware player. When I connect this USRP1 via USB 2.0 drive to Windows 7 it is recognized as Ettus Research LLC USRP1... When I connect the device to Ubuntu through VMware, it shows: usb device fffe:0002 on my removable devices. When I run lsusb I receive the following: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub Bus 001 Device 004: ID fffe:0002 When I run this program that comes with the USRP driver... uhd_find_devices I receive: -------------------------------------------------- -- UHD Device 0 -------------------------------------------------- Device Address: type: usrp1 name: serial: 00000000 So when I run this program, it does recognize the fact that this device is connected. However, the device has no address, no name, and has a null serial. I need to know the device address so I can run more programs in GNURadio. Does anyone know what the problem is here? Thanks!

  Read the article

• How do I get wireless and video working on a Sony Vaio vpc-z21x9r

  - by Alex

  OS: Ubuntu 11.10 Kernel: 2.6.37.6 Laptop: sony vaio vpc-z21x9r The problem: I can't change level of screen backlight; also can't enable wi-fi. While using 3.0 kernel everything is ok, but the laptop discharges too quickly. Results for lspci 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 5f) VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) there is no wlan0 in ifconfig -a too. I've fount that kernel should already have drivers for this graphics controller, but when i load up in restore mode, it writes "fall" while trying to load up some video drivers. To change the level of backlight i've alrady tried: xbacklight -set XX , smartdimmer -s XX and got this init_ nvclock() failed! also sudo setpci -s 00:02.0 F4.B=XX with no results. As for wi-fi, i've found driver but i don't understand how to install it. Here it is How can I fix these problems? Thank you for your help and time! Also tried to fix problems with backlight writing GRUB_CMDLINE_LINUX_DEFAULT="quiet splash nomodeset acpi_backlight=vendor Still no results. Is there any sense in recompiling kernel, I mean 2.6.37.6. Can it make any improvements in the situation?

  Read the article

• Boot ubuntu 12.04 in 3D - nomodeset quiet splash install

  - by rahi

  I would like to enable 3D in Ubuntu 12.04. I recently tried to install ubuntu on a new computer. When the installation was complete and I rebooted the machine, I could only see a blank screen. After some searching, I followed this tutorial which instructed me to boot with "nomodeset" enabled. I choose this on the USB I was installing ubuntu 12.04 from. Fortunately, the ubuntu installation on the new computer was successful. When I tried to change the size of the unity launcher icons, I did not see that option (as I see on my other computer running ubuntu 12.04). I tried installing MyUnity and it told me that the computer I had just installed 12.04 to was running in 2D. To my knowledge. all the software is up to date (as I ran the Software Updater). In addition, when I look for Additional Drivers, I see a message that says "No proprietary drivers are in use on this system". When I look under System Details Graphics, I see the Driver as "VESA:Intel Sandybridge/Ivybridge Graphics. When I hold the shift key on when my machine boots up, and type "e" on the Grub menu, I see the following towards the end, "nomodeset quiet splash $vt_handoff". Does this have anything to do with the plain 2D ubuntu 12.04 experience? Again, what I'd like to do now is get the 3D experience on my new machine running 12.04. Please let me know if you need more information.

  Read the article

• HP Notebook Pavilion g6-2101sl freeze

  - by StErMi

  I just bought this notebook and I've already installed in a new partition Ubuntu 12.04 LTS with 6gb of swap memory. UPDATE2: This is the laptop configuration: http://h10025.www1.hp.com/ewfrf/wc/document?cc=it&lc=it&dlc=it&tmp_geoLoc=true&docname=c03397517 Sometimes (without any special conditions) Ubuntu freezes. My mouse is blocked, the UI is blocked, ALT+F1 to kill something or to restart is blocked, I can't really do anything... I've also tried and it freezes with: Ubuntu 3D Ubuntu 2D Gnome Shell and it freezes both with low and high load. I can only press on power button (physically) and restart my laptop (and this is not the correct way to do things). I'm using this laptop for work, so I need a stable OS without this freeze. Someone knows how to solve this problem? UPDATE: /var/log/messages is empty /var/log/kernel.log - http://paste.ubuntu.com/1220182/ /var/log/Xorg.0.log - http://paste.ubuntu.com/1220186/ I just installed propetary driver from ATI, it crash anyway. This morning I started laptop, I enabled wireless, opened dropbox and chrome - freeze. When it freeze I cannot: Do ctrl+alt+f1 to get console access AltF2 + r to reload session Alt+Print + RESUB to restart I totally freezed.

  Read the article

• How to build the mainline kernel source package?

  - by Maxime R.

  Ubuntu kernel PPA only provides linux-headers*.deb and linux-image*.deb packages. How can I build the corresponding linux-source*.deb package ? Context: I'm currently running Ubuntu 11.10 with the mainline kernel (3.2 rc6 now) to get a better support for my sandybridge IGP (Dell E6420 laptop with intel i5-2520M CPU). Appears, i'd like to install this touchpad driver, ALPS touchpads being badly supported (see previous link bug report), while waiting for upstream support in kernel version 3.3. Problem is, DKMS keeps complaining about not finding the full kernel source: Module build for the currently running kernel was skipped since the kernel source for this kernel does not seem to be installed. Appears I may not need the full source but I'd still like to try having it installed to see if it solve my problem. What I tried : Uncompressing the kernel.org source archive in /usr/src/. DKMS still complaining. Manually updating the kernel source package with uupdate and the mainline source package like explained here. Did not succeed. Manually building the linux-source package following @roadmr and @elmicha instructions. I eventually succeeded to build it but DKMS still complained about the missing source. At last I noticed an error I did not catch in the first place while reinstalling the kernel headers. Appears the .deb I got may have been corrupted, downloading it again did the trick :) Alas, while DKMS agreed to compile the module i ran into the following error which appears to have already been reported. This issue isn't yet solved but I won't try to because of the following: in the end I decided to test the precise kernel version 3.2-rc6 through the xorg-edgers ppa which appears to be correctly patched: it works. Nevertheless, it might still be of some interest to know how to build the mainline linux-source package as the Ubuntu Kernel Team doesn't provide it. Not to mention that I learned a lot in the process ^^

  Read the article

• Impossible to enable bluetooth under Ubuntu

  - by PCh

  I just installed Ubuntu 12.04 (dual boot, kept Windows just in case) on my new Acer Aspire One 756-877. As soon as I installed it I also installed the Broadcom driver, since wifi wasn't working, and that solved it right away. But when I tried Bluetooth, I had a problem that I see is quite recurring: -The hardware is on (and working fine under Windows) -The icon shows up on the menu, giving me the options of turning Bluetooth on or off, and then just "Bluetooth preferences". -I can apparently turn it on that way, which only lights up the icon but makes no difference at all (and doesn't give any other options in the Bluetooth menu) -When I open "Bluetooth preferences" (whether Bluetooth is apparently on or off, it makes no difference), it says it's disabled and will not let me slide the button to enable it. I've rebooted, but nothing happens. -The material is Broadcom and the port (if it's relevant at all) is Port_#0001.Hub_#0003 I tried the following commands suggested in other similar questions, with no result at all: sudo dmesg | grep blue and sudo service bluetooth start and sudo /etc/init.d/bluetooth start Any other clues on what I can do? Thanks for your time!

  Read the article

• Higher resolutions unavailable with 2.6.38-8 kernel

  - by time-wastrel

  After upgrading to Natty and the 2.6.38-8 kernel I could no longer obtain the 1920x1080 resolution available in Maverick with 2.6.35-22. In fact the boot occasionally hung. However, after selecting the remaining 2.6.35-22 kernel, the high resolution was available. I then made the mistake of completely reinstalling, but could never get the higher resolutions with 2.6.38-8, no matter what I did. e.g. trying the nvidia proprietary driver, creating an xorg.conf. Even from the command line using xrandr --newmode "1920x1080_60.00" 173.00 1920 2048 2248 2576 1080 1083 1088 1120 -hsync +vsync xrandr --addmode DVI-I-1 1920x1080_60.00 xrandr --output DVI-I-1 --mode 1920x1080_60.00 all I would get would be a blank screen and the monitor reporting no input. (Low resolutions displayed fine with xrandr.) I could actually add the 1920x1080 to the already existing probe-reported resolutions in the pool of available resolutions, but choosing it would give the blank screen. In the end I installed the 2.6.35-22 kernel again. The high resolution is back. For a while there, staying up all night and trying many things, I thought that a new video board or monitor might be needed, but deep down, I knew that they were both OK. My question is - "Is this some bug involving the latest kernel, that will go away, or if this persists in future kernels, is there a way to make sure that I can keep my native resolution?"

  Read the article

• Need to run a .sh as root on boot or login

  - by Graymayre

  Still new with linux and running ubuntu 12.10 I have a wireless stick (ae2500) which has known issues that has been partially solved using ndiswrapper. However, to use it I must run the same scripts every time I reboot, effectively uninstalling and reinstalling the driver. I made a .sh file to run every time to make it easy, but I must do the sudo login everytime. There are three solutions I am looking for and although not all are necessary to solve this particular problem, I would still like to know them all for learning purposes. run scripts or file.sh on boot (as well as other programs) run scripts or file.sh automatically with root privileges make the install permanent so as not to have to go through the process every time. Any additional information that can help me regarding this that I did not think to ask (including streamlining my commands), or general knowledge, would be greatly appreciated. Following are the contents of the file. I pretty much just made it as I would have entered it. cd ~/ndiswrapper-1.58rc1 sudo modprobe -rf ndiswrapper sudo rm /etc/modprobe.d/ndiswrapper.conf sudo rm -r /etc/ndiswrapper/* sudo depmod -a sudo make uninstall sudo make sudo make install sudo ndiswrapper -i bcmwlhigh5.inf ndiswrapper -l sudo modprobe ndiswrapper

  Read the article

• Fix for poor hd playback for 11.04 upwards

  - by mark kirby

  Hi guys ive seen loads of posts on this site about poor 720/1080p playback in recent ubuntu versions I had this problem and fixed it so I thought id share it with everyone.... 1 install mplayer 2 install smplayer frontend {in software center} 3 open smplayer 4 go to "OPTIONS" then "PREFRENCES" then "GENRAL" 5 if you have a nvidia card choose "OUTPUT DRIVER" and select "VDPAU" {for ATI or AMD choose xv (0 - ATI Radeon AVIVO video) I dont know if this will work as my card is nvidia but it should) 6 go to performance on the left hand side and set both local and streaming cache to 99999 (this may also fix dvd playback if you set that cache aswell} 7 check the box for "ALLOW HARD FRAME DROP" and set "LOOP FILTER" to skip only on HD 8 Set the "THREDS FOR DECODING OPTION TO THE NUMBER OF CORES YOUR CPU HAS IF YOU HAVE MORE THAN ONE CPU ADD UP ALL THE CORES FOR BEST PERFORMANCE" 9 Enjoy you HD movies again on ubuntu...... I have a pretty avrage machine heres my spec.... 2x Pentium 4 ht 3 ghz Stock dell power and motherboard GFORCE 310 HDMI 24 inch full HD tv as a monitor so any one with dule core cpu should have no problems getting this to work. hope this helps someone out.

  Read the article

• Unable To Get Sound Working to External Speaker on HP TouchSmart 320 on 11.04 or 11.10

  - by Schof

  This is an HP TouchSmart 320, model number 320-1200m. I'm using Ubuntu 11.04. Hardware information: root@hp320:/home/mpower# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 root@hp320:~$ cat /proc/asound/card0/codec#0 | grep Codec Codec: IDT 92HD91BXX Sound to headphone jack works properly, but sound to built-in speakers does not work. I have installed Windows, and with Windows 7 installed, all audio hardware works properly, so this isn't a hardware fault. I've looked at https://help.ubuntu.com/community/HdaIntelSoundHowto and have been unable to find my card in http://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio-Models.txt . I have tried adding almost every conceivable model in the line "options snd-hda-intel model=MODEL" line I added to /etc/modprobe.d/alsa-base.conf. Update 2011-11-09 2:31 PM PST: I've gone to Control Center - Sound Preferences to attempt settings that make sound work. The "Hardware" tab shows one device: "Internal Audio 1 Output / 1 Input Analog Stereo Duplex." There are two output profiles listed in the selection box at the bottom of the tag: Analog Stereo Duplex and Analog Stereo Output. Neither cause sound to emit from the speakers. I've also run alsamixer on the command-line and ensured that everything is set to maximum and nothing is muted. Update 2011-11-09 5:15 PM PST: I've replicated the exact same symptoms in 11.10. Update 2011-11-10 11:31 AM PST: I've filed a bug in launchpad: https://launchpad.net/ubuntu/+source/alsa-driver/+bug/888703

  Read the article

• Unity 3D does not work on Dell system with a AMD Radeon HD 6470M

  - by VeeKay

  I am running 64 bit Ubuntu on Dell with 1GB graphic card. I login with "Ubuntu" hoping to see Unity 3d but it doesn't. Unity 2D runs instead. when I type in echo "$DESKTOP_SESSION" it confirms the Unity-2D. I've checked the System info that shows like : The graphics row shows itself as empty. SO I've presumed that the graphic drivers aren't detected and hence I went to Unity- Additional Drivers and installed the fglrx driver that the UI has suggested. Even after installing so, the graphics part in System info details shows nothing and still Unity 2D runs in spite of all the effort. Please help! How can I get my Unity 3D back? Hardware Info Video Card : AMD Radeon™ HD 6470M - 1GB (For ICC) RAM : 6GB (1 X 2GB + 1 X 4GB) 2 DIMM DDR3 1333Mhz OS : 64 bit Ubuntu 11.10 Edit : Output for /usr/lib/nux/unity_support_test -p X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 155 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 21 Current serial number in output stream: 21

  Read the article

• CodePlex Daily Summary for Tuesday, August 05, 2014

  CodePlex Daily Summary for Tuesday, August 05, 2014Popular ReleasesGMare: GMare Beta 1.3: Fixed: Sprites not being read inLib.Web.Mvc & Yet another developer blog: Lib.Web.Mvc 6.4.2: Lib.Web.Mvc is a library which contains some helper classes for ASP.NET MVC such as strongly typed jqGrid helper, XSL transformation HtmlHelper/ActionResult, FileResult with range request support, custom attributes and more. Release contains: Lib.Web.Mvc.dll with xml documentation file Standalone documentation in chm file and change log Library source code Sample application for strongly typed jqGrid helper is available here. Sample application for XSL transformation HtmlHelper/ActionRe...Virto Commerce Enterprise Open Source eCommerce Platform (asp.net mvc): Virto Commerce 1.11: Virto Commerce Community Edition version 1.11. To install the SDK package, please refer to SDK getting started documentation To configure source code package, please refer to Source code getting started documentation This release includes many bug fixes and minor improvements. More details about this release can be found on our blog at http://blog.virtocommerce.com.Json.NET: Json.NET 6.0 Release 4: New feature - Added Merge to LINQ to JSON New feature - Added JValue.CreateNull and JValue.CreateUndefined New feature - Added Windows Phone 8.1 support to .NET 4.0 portable assembly New feature - Added OverrideCreator to JsonObjectContract New feature - Added support for overriding the creation of interfaces and abstract types New feature - Added support for reading UUID BSON binary values as a Guid New feature - Added MetadataPropertyHandling.Ignore New feature - Improv...Aitso-a platform for spatial optimization and based on artificial immune systems: Aitso_0.14.08.01: Aitso0.14.08.01Installer.zipVidCoder: 1.5.24 Beta: Added NL-Means denoiser. Updated HandBrake core to SVN 6254. Added extra error handling to DVD player code to avoid a crash when the player was moved.EasyMR: v1.0: 1 ????????? 2 ????????? 3 ??????? ????????????????????，???????????????，???????????PowerShell App Deployment Toolkit: PowerShell App Deployment Toolkit v3.1.5: *Added Send-Keys function to send a sequence of keys to an application window (Thanks to mmashwani) *Added 3 optimization/stability improvements to Execute-Process following MS best practice (Thanks to mmashwani) *Fixed issue where Execute-MSI did not use value from XML file for uninstall but instead ran all uninstalls silently by default *Fixed error on 1641 exit code (should be a success like 3010) *Fixed issue with error handling in Invoke-SCCMTask *Fixed issue with deferral dates where th...Facebook Graph Toolkit: Facebook Graph Toolkit 5.0.493: updated to Graph Api v2.0 updated class definitions according to latest documentation fixed a potential memory leak causing socket exhaustion LINQ to FQL simplified usage performance improvement added missing constructorsCrashReporter.NET : Exception reporting library for C# and VB.NET: CrashReporter.NET 1.4: Added French, Italian, German, Russian and Spanish translation. Added DeveloperMessage field so developers can send value of variables or other details they want along with crash report. Fixed bug where subject of crash report email was affected by translation. Fixed bug where extension is not added in SaveFileDialog while saving crash report.AutoUpdater.NET : Auto update library for VB.NET and C# Developer: AutoUpdater.NET 1.3: Fixed problem in DownloadUpdateDialog where download continues even if you close the dialog. Added support for new url field for 64 bit application setup. AutoUpdater.NET will decide which download url to use by looking at the value of IntPtr.Size. Added German translation provided by Rene Kannegiesser. Now developer can handle update logic herself using event suggested by ricorx7. Added italian translation provided by Gianluca Mariani. Fixed bug that prevents Application from exiti...Windows Embedded Board Support Package for BeagleBone: WEC2013 Beaglebone Black 03.02.00: Demo image. Runs on BeagleBone White and Black. On BeagleBone Black works with uSD or eMMC based images. XAML support added. SDK and demo tests included. New SDK refresh (uninstall old version first) IoT M2MQTT client built in. Built and maintained in the U.S.A.!Essence#: Philemon-3 (Alpha Build 19): The Philemon-3 release corrects a problem with the script of the NSIS installation program generator used to build the installer for the previous release. That issue could have been addressed by simply fixing the script and then regenerating the installation program, but a) it was judged to be less work to create a new release based on the current development code, and b) a new release does a better job of communicating the fact that the installation program for the previous release is broken...SEToolbox: SEToolbox 01.041.012 Release 1: Added voxel material textures to read in with mods. Fixed missing texture replacements for mods. Fixed rounding issue in raytrace code. Fixed repair issue with corrupt checkpoint file. Fixed issue with updated SE binaries 01.041.012 using new container configuration.Continuous Affect Rating and Media Annotation: CARMA v6.02: Compiled as v6.02 for MCR 8.3 (2014a) 32-bit Windows version Ratings will now only be saved for full seconds (e.g., a 90.2s video will now yield 90 ratings instead of 91 ratings). This should be more transparent to users and ensure consistency in the number of ratings output by different computers. Separated the XLS and XLSX output formats in the save file drop-down box. This should be more transparent to users than having to add the appropriate extension.Magick.NET: Magick.NET 6.8.9.601: Magick.NET linked with ImageMagick 6.8.9.6 Breaking changes: - Changed arguments for the Map method of MagickImage. - QuantizeSettings uses Riemersma by default.Wallpapr: Wallpapr 1.7: Fixed the "Prohibited" message (Flickr upgraded their API to SSL-only).DbEntry.Net (Leafing Framework): DbEntry.Net 4.2: DbEntry.Net is a lightweight Object Relational Mapping (ORM) database access compnent for .Net 4.0+. It has clearly and easily programing interface for ORM and sql directly, and supoorted Access, Sql Server, MySql, SQLite, Firebird, PostgreSQL and Oracle. It also provide a Ruby On Rails style MVC framework. Asp.Net DataSource and a simple IoC. DbEntry.Net.v4.2.Setup.zip include the setup package. DbEntry.Net.v4.2.Src.zip include source files and unit tests. DbEntry.Net.v4.2.Samples.zip ...Azure Storage Explorer: Azure Storage Explorer 6 Preview 1: Welcome to Azure Storage Explorer 6 Preview 1 This is the first release of the latest Azure Storage Explorer, code-named Phoenix. What's New?Here are some important things to know about version 6: Open Source Now being run as a full open source project. Full source code on CodePlex. Collaboration encouraged! Updated Code Base Brand-new code base (WPF/C#/.NET 4.5) Visual Studio 2013 solution (previously VS2010) Uses the Task Parallel Library (TPL) for asynchronous background operat...Wsus Package Publisher: release v1.3.1407.29: Updated WPP to recognize the very latest console version. Some files was missing into the latest release of WPP which lead to crash when trying to make a custom update. Add a workaround to avoid clipboard modification when double-clicking on a label when creating a custom update. Add the ability to publish detectoids. (This feature is still in a BETA phase. Packages relying on these detectoids to determine which computers need to be updated, may apply to all computers).New ProjectsAPS - Folha de Pagamento: Folha de PagamentoCIS470 Metrics Tracking: A data driven application designed to display various project progress metrics and reports based off of data. CIS470 Metrics Tracking DeVry Capstone project.Excel Converter: A great tools to convert MS excel to PDF and vice verse. We plan support both Window and Web version.FreightSoft: A Web Based Shipping and Freight Management SystemGoogle .Net API: Dot Net warp for Google API Services. API Demo, documentation, simple useful tools. Welcome to join us make more google API works on Dot Net World. Google Driver downloader: A free tool to bulk download file from google driver to local box.Omniprogram: OmniprogramOnline OCR: A free to OCR via google APIOnline Resume Parsing Using Aspose.Words for .NET: Online Resume Parsing Using Aspose.Words for .NET. PDF Text Searcher: This application searches for a word from the PDF file name inside the PDF itself.PEIN Framework: A collection of day to day required libraries.Public Components: Public Components, by Danny VarodRole Based View for Microsoft Dynamic CRM 2011 & 2013: Allow admin to configure entity's view based on role.scmactivitytfs: Test project to play with Team Foundation Server.Selfpub.CrmSolution: Tram-pam-pamWindGE: WindGE????DirectX11??????3D???????，????????????????????，???WPF???????。yao's project: a project for personal study

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >