Search Results

Search found 21006 results on 841 pages for 'virtual desktop'.

Page 183/841 | < Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >

• DIsable my nv video card driver in linux

  - by Dahaka Wang

  I'm trying to passthrough my nv video card to my domU, but I could not bind my video card to the pciback driver I only have one video card with the pci number 0000:03:00.0, so I used the following command echo -n "0000:03:00.0" > /sys/bus/pci/drivers/nouveau/bind to unbind the nouveau driver from my video card. The screen went black because I have forcefully removed the video driver, therefore I ssh'd into the computer to run further commands I ran: echo -n "0000:03:00.0" > /sys/bus/pci/drivers/pciback/bind to try to bind it to my pciback driver, but I got: bash: echo: write error: No such device I found out that this was the message shown when trying to bind a PCI device which is already bound. Therefore, I think that something was still using my video card Can anyone help me out? Thanks a lot!

  Read the article

• Proxmox: VMs and different public IPs

  - by Raj

  I have a server which has two NICs and both are directly connected to internet. I have five different public IP addresses available for the VMs. The host machine (Proxmox) doesn't need to use any (it'll use a private IP and that's all) but will have internet connection. I've gone through the Proxmox documentation and I'm not able to understand the big picture to set up the right network configuration for my needs. In short, what I have is: One server (Proxmox, host machine) On that server, 5 VMs are created 5 public IP addresses available (one for each VM), let's say: 80.123.21.1, 80.123.21.2, 80.123.21.3, 80.123.21.4, 80.123.21.5 What I have now for the host is the following: auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto eth1 iface eth1 inet manual auto vmbr0 iface vmbr0 inet static address 192.168.1.101 netmask 255.255.255.0 bridge_ports eth0 bridge_stp off bridge_fd 0 auto vmbr1 iface vmbr1 inet manual It can be reached from the internal network, so that's OK. It has internet connection, which is also OK. vmbr1 is going to be used by the VMs. Each VM will have its own IP on his network interfaces configuration file. For some reason, VMs will not have internet and they won't be able to have public IP address. If I use NAT, it will work correctly, but they will not use the public allocated IP addresses for them. Am I missing something?

  Read the article

• Any consumer routers with Outgoing VPN support?

  - by Brian Lacy

  When I'm working at home, I need to be able to connect to three different outgoing VPNs, two of which happen to use the same internal IP addressing schemes (192.168.0.*). I also need a static address for my VirtualBox VM so I can connect to my testing web server. Are there any routers which will allow me to connect to multiple outgoing VPNs and assign different internal IP addresses through NAT? Is such a thing even possible, or are there alternate solutions available? Thanks!

  Read the article

• Monitor Windows Terminal Sessions from Linux/Mac

  - by mhd

  I'm writing some scripts to make remote connections to a Windows 2003 server a bit more user-friendly, and in doing this I want to see who's logged in already. In Windows, I could use qwinsta.exe to do this, even for remote servers. So it is exposed somehow, but I couldn't find a matching command line tool for Unix. Lacking such a tool, I could install an ssh server on the machine and call it remotely, parsing the output or write a small service of my own that would expose this via http, if I don't want full-blown ssh access. Do I have to do this, or is there already a tool for querying terminal services remotely?

  Read the article

• How can I make VNC faster?

  - by NickAldwin

  I need to remotely access and use my work computer a few times a week. I want to use VNC because of the price. I've used VNC before, mostly on my own network, where it's fast. However, VNC over the internet is incredibly slow. Even at 256 colors and lower, with Aero turned off, it is unbearably slow. I recently used Ammyy Admin to connect to do something requiring a quick reaction time. Ammyy was really fast, with almost no lag, and it was running in full color with Aero on! How can I make VNC faster, like Ammyy is? I'd use Ammyy, but I would probably run into the 15hr/month limit pretty quickly. Any suggestions? [EDIT] I'm currently using UltraVNC.

  Read the article

• Server needs to ping outgoing before allowing connection

  - by QuintenVK

  Okay, first our setup: I'm currently working over VPN to a mac mini OSX 10.6 server. We have a testsetup VM running on that, using ubuntu 12.04. Earlier today, there was an outage because of which our mac mini server was reset. Since then, i was unable to initiate a connection to the VM (which i did boot) -- no ssh, no web, ... . I couldn't ssh or web from the mac mini to the vm either. I could do so from within the VM itself, though. Ping did work on all machines. Lastly, I tried pinging from the VM to my laptop. It took a moment, but then it finally started to ping (no timeouts or so). After that, web and ssh magically worked. I then didn't use the machine for about 5 minutes, after which i had to ping from the server to my laptop again before i could setup a connection. I'm in the dark on what this could be, though I think this is something to do with lookups.

  Read the article

• Windows 8 / Server 2012 RDP connection is slow

  - by Chris

  I recently installed Windows Server 2012 for development purposes at our office and noticed immediately that connecting via RDP is slow. It can take 5-10 seconds to connect at times, where as connecting to any of our Win7 or Win2008R2 boxes takes at most 1-3 seconds. At first, I chalked this up to the box itself needing a driver update or something, but just yesterday, I installed Win8 on my desk PC and connecting from home to that machine produces the same result. There is a 3-4 second pause at "securing remote connection" and then again at "configuring remote session". I don't see any warnings in the event log, and once connected, there do not appear to be any performance issues. Is there a known problem with RDP connections on Windows 8 systems? Anything I should look for?

  Read the article

• Can't Remote into Windows Server

  - by Brian

  Hello, I have a Dell server wired into the router. I was able to connect to it with my laptop (laptop is wireless) before my router died. My verizon router went kaput, and I got everything else back up and running on the wireless network other than the remoting in feature, even though I can access the server through windows explorer just fine. Any ideas why? What do I need to check? UPDATE: Interesting scenario, Network Discovery is off; I turn it on and save, but for some reason, even after that, network discovery is turning itself off... no idea why that is happening? Thanks.

  Read the article

• Remote viewing on a Linux server?

  - by Zeno

  I have a Slackware Linux server that doesn't have a monitor. It doesn't run any GUIs. Is there a way to remotely access the screen? I always use SSH, but there are times where the SSH services fails and I can't do anything (nor even tell what the problem is). I use Teamviewer from my Windows computer to other PCs, but is there anything I can use to remotely view this from a Windows machine? I also want to see what it's doing at boot, before the SSH service starts.

  Read the article

• Sub $300 machine.

  - by Moshe

  Preferably not a netbook, please. should support windows7 at a normal speed.

  Read the article

• Is it possible to live-boot VirtualBox from a USB flash drive?

  - by bw.

  To clarify, I'm not asking if you can boot from USB from within VirtualBox. I would like to make a portable version of Windows 7 that I can run from a USB drive on any machine. I'm putting a distro of Linux on my laptop, but I manage a Windows domain at work so I'd like an easier management solution than trying to use Linux tools to interface with a Windows DC(as RDP to a DC is not always an option). The reason I'm inquiring about VirtualBox... I plan on carrying this portable installation with me and using it on multiple machines, so I would like to avoid driver conflicts (which I imagine would happen if I only installed Windows on a flash drive). Basically, I need a way to boot an installation of Windows 7 from USB that still allows me to install/remove/update programs as if it were installed on a standard hard drive, and not freak out over different hardware configurations. Please help, superusers!

  Read the article

• VirtualBox OSE: Install Guest OS On Headless Host Via VNC?

  - by Eddie Parker

  I've remotely installed VirtualBox OSE on my Gentoo box at home. I have everything set up and ready for the OS. However all the documentation I've read seems to say that you can only use the PUEL version in order to get remote access during installs - does anyone know if it's possible to do similar with the OSE but using VNC? Links to documentation or tutorials would be welcome, apparently my Google-Fu is failing me, if it's out there. Thanks.

  Read the article

• Join Domain from VM

  - by Adis

  I have two VMs running on VMWare Player. I use NAT adapter settings. The host machine for VMs is running on corporate network. First VM has Domain controller running and I can log in on that machine using domain credentials. I named domain wm.local When I run IP config on this machine: IP: 192.168.87.132 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 Second VM cannot join domain. When I try it with domain WM I'm propmted for credentials. And I enter Administrator credentials and than it waits for some time and I get response: "The specified domain either does not exist or could not be contacted" If i type wm.local as domain when trying to join it does not prompt me to login but just shows "An Active Directory Domain Controller (AD DC) for the domain wm.local could not be contacted. And here it takes no time to get this error message. Ipconfig on this machine: IP: 192.168.87.134 Def Gataway: 192.168.87.2 DNS server: 192.168.87.2 DHCP server: 192.168.87.254 I can ping second VM from first one. And I disabled firewalls on both machines. Any ideas? Is there any manual for this?

  Read the article

• Computer wont start, just blinks on and off

  - by Ryan

  This is really strange. I had a comp that was working fine for over a year, then suddenly it started to shut off, it got so bad that I press the power button and in around 30 secs while booting windows it would shut off, then 20 secs... then 10 secs, then it refused to start all together. So I bought a new PSU (850w Thermaltake, the old one was 550w corsair) thinking that was the problem, I fitted the new PSU now and its the same thing, I press the power button and my fans start for a split second (they have led lights on them, so the lights come on) and then everything goes off again. I thought maybe it was my power button that was loose on my comp, luckily I had another chassis near by so I disconnected the powerSW from the old one and put ran the powerSW from the new chassis, press the power on the new chassis and same thing, it blinks for a split second and off again. Double checked connections from the PSU to the cpu power as well as board mobo power, its tight. It's pretty unlikely both the PSUs have the same exact problem so am lost... Suggestions?

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• Why do I get swap space related errors when I still have lots of free memory in Solaris 10?

  - by Tom Duckering

  I am seeing a few of my services suffering/crashing with errors along the lines of "Error allocating memory" or "Can't create new process" etc. I'm slightly confused by this since logs show that at the time the system has lots of free memory (around 26GB in one case) of memory available and is not particularly stressed in any other way. After noting a JVM crash with similar error with the added query of "Out of swap space?" it made me dig a little deeper. It turns out that someone has configured our zone with a 2GB swap file. Our zone doesn't have capped memory and currently has access to as much of the 128GB of the RAM as it need. Our SAs are planning to cap this at 32GB when they get the chance. My current thinking is that whilst there is memory aplenty for the OS to allocate, the swap space seems grossly undersized (based on other answers here). It seems as though Solaris is wanting to make sure there's enough swap space in case things have to swap out (i.e. it's reserving the swap space). Is this thinking right or is there some other reason that I get memory allocation errors with this large amount of memory free and seemingly undersized swap space?

  Read the article

• How to let Linux Python application handle termination on user logout correctly?

  - by tuxpoldo

  I have written a Linux GUI application in Python that needs to do some cleanup tasks before being terminated when the user logs out. Unfortunately it seems, that on logout, all applications are killed. I tried both to handle POSIX signals and DBUS notifications, but nothing worked. Any idea what I could have made wrong? On application startup I register some termination handlers: # create graceful shutdown mechanisms signal.signal(signal.SIGTERM, self.on_signal_term) self.bus = dbus.SessionBus() self.bus.call_on_disconnection(self.on_session_disconnect) When the user logs out, neither self.on_signal_term nor self.on_session_disconnect are called. The problem occurs in several scenarios: Ubuntu 14.04 with Unity, Debian Wheezy with Gnome. Full code: https://github.com/tuxpoldo/btsync-deb/tree/master/btsync-gui

  Read the article

• How to repair Creative Inspire Speakers 2.1 Volume Control Wheel?

  - by akula

  Due to dust or so, the Volume Control Wheel does not work properly. Volume goes to one speaker, and other gets muted. Vice versa. When I carefully turn the wheel sometimes the Volume works properly or sometimes with noise or muted one side. As I write this, I've cleaned it up with Petrol drops. PCB is drying. I chose Petrol because Contact Cleaner is expensive solution. Am I correct or any other method could be used? Thank you.

  Read the article

• What is Paging in memory management?

  - by Fasih Khatib

  I was just reading Operating System Principles by Silberschatz et al when I came across paging in memory management.I'm slightly confused about it. It states that Physical Memory(I assume it's RAM) is divided into frames, and logical memory is divided into pages. CPU generates logical addresses containing page number and an offset. This page number is used to retrieve the frame number from a page table which gives the base address so the physical address is calculated as base+offset. My question is: is the page table maintained for every process? I logically think that the answer would be yes as every process will need to map its own pages to frames. I may be wrong. Please clarify. Also: paging and segmentation(where 'holes' are created in memory) are two totally different techniques that are not used in combination. Correct?

  Read the article

• Where to look for regular scripts?

  - by fontan

  It seems to me that our server freezes every 30 days around noon due to the huge utilization of xvda data transfer partition - writes are 50 times higher than normally (according to the health monitor in plesk). This seems to me as the reason why the apache & co becomes instable as (for example) all apache's processes are waiting to write their log (according to the service's full status). I am, however, unable to find any scheduled task that would be executed during that period. I have checked both cron and anacron setup and there is only one monthly anacron task which is not executed (according to the /var/log/cron - and there is nothing unusual) around noon. Are there any other places where to look for periodical processes? (I am just about to ask server's provider the same question about any external maintenance run around this time but I don't expect them to run anything time/resource consuming during the day.)

  Read the article

• Is it possible to export an OpenVZ machine and use it after OpenVZ?

  - by Somebody still uses you MS-DOS

  I'm planning to use OpenVZ in an old machine I have at home. I want to know if a dumped OpenVZ instance image can be exported to other formats (like VirtualBox or Vmware). Thanks!

  Read the article

• Datastage 8.7 installs fine on Window7 without any errors but it can not launch localhost:9080 web console

  - by user265273

  When I launch the web console, I get page can not be displayed error. What I have tried so far: I have re-installed DS about 7 times, and each time, I get same errors. I added entries in etc/hosts file for local host and my host name. I have turned off firewall. My hardware/software setup. My host system is window8.1. My vmware workstation is 7. The guest os is windows 7 enterprise x64. I have installed 10g, and given dba role to public. I have installed VS 5, and ms visual c++ 2010 express. I have installed msxml. IE version is 10. Firewall is off. My internet works fine It passed all the DS requirement tests and install completed successfully. When I launch my vmware guest instance, I do get SQL5000c error upon boot which I have tried to ignore in some installs and in some, I used db2systray -clean command to get rid of it. But that has not helped solve the webconsole connect failure to my host. I have spent over 2 weeks exclusively on this issue and badly need some help.

  Read the article

• VirtualBox or else programs to run Mac OS virtually on Windows 7

  - by blgnklc

  any idea will help me to enlarge the boundaries surround me nowadays. regards

  Read the article

• Does Win7 VPC negate need to re-install?

  - by justSteve

  I fear i have an impending hardware breakdown coming ... the last time the box booted i had to power off and on a couple times before windows loaded. Seems fine when up and running. So i'm preparing to install new hardware and would like to bring over the currently installed image. From what i've read of VM capabilities of VM i shouldn't have to re-install? VM seems most applicable to data centers and enterprises. I'd like to see some coverage of the tricks for SOHO users.

  Read the article

• Can not connect remotely to MySQL Server on Ubuntu 10.10

  - by BobFranz

  Ok I have searched google for two days trying to get this to work. Here are the steps I have taken so far: Clean install of Ubuntu 10.10 Install mysql 5.1 as well as admin Comment out the bind address in the config file Create a new database Create a new user that is username@% to allow remote connections Grant all access to this user to the new database EXCEPT the grant option Login on the server is ok using this new user and database on the localhost Login on the server is ok using this new user and database on the server internal network ip Login from a remote computer is ok using this new user and database using the internal network ip Login is not working when logging in with this username and database using the external ip address from the server or the remote computer. I have port forwarding enabled for this port and it is viewable from outside as confirmed by canyouseeme.org I have nmap'd using the following command on the internal ip and get the below result: nmap -PN -p 3306 192.168.1.73 Starting Nmap 5.21 ( http://nmap.org ) at 2011-02-19 13:41 PST Nmap scan report for computername-System-Name (192.168.1.73) Host is up (0.00064s latency). PORT STATE SERVICE 3306/tcp open mysql Nmap done: 1 IP address (1 host up) scanned in 0.23 seconds I have nmap'd using the following command on the internal ip and get the below result(I have hidden ip for obvious reasons): nmap -PN -p 3306 xxx.xxx.xx.xxx Starting Nmap 5.21 ( http://nmap.org ) at 2011-02-19 13:42 PST Nmap scan report for HOSTNAME (xxx.xxx.xx.xxx) Host is up (0.00056s latency). PORT STATE SERVICE 3306/tcp closed mysql Nmap done: 1 IP address (1 host up) scanned in 0.21 seconds I am completely stuck here and need some help. I have tried everything under the moon and still can not connect from a remote external ip address. Any help is greatly appreciated and I need to do anything to help find the problem let me know and I will post the results here.

  Read the article

< Previous Page | 179 180 181 182 183 184 185 186 187 188 189 190  | Next Page >