Search Results

Search found 5312 results on 213 pages for 'dns recursion'.

Page 186/213 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

• Problem with TL-R480T+ and static routes

  - by Globulopolis

  Hi! I've some question about this router. Before starting, some configurations, specified by my provider. Wan1 VPN IP - 192.168.172.84 Mask - 255.255.255.0 Gateway - 192.168.172.253 DNS - 195.110.6.7 Wan2 Dynamic IP DHCP - 168.120.1.34 Mask - 255.255.255.0 Router IP 192.168.1.1 Computer IP 192.168.1.7 Routes: route -p add 192.168.0.0 mask 255.255.0.0 192.168.172.253 route -p add 195.110.6.0 mask 255.255.254.0 192.168.172.253 route -p add 88.135.112.0 mask 255.255.240.0 192.168.172.253 route -p add 178.219.160.0 mask 255.255.240.0 192.168.172.253 For first provider I need to provide a routes. 'Cause router does not support different routes for different WAN interfaces I put them in "Static routes". But when I try to save them I've got an error: Destination IP address can not be set in a same subnet with the WAN or LAN IP address. If I change IP's to local like 192.168.x.x router tell me: Gateway must be set in a same subnet with WAN or LAN IP address. Changing mask on WAN1 interface to 255.255.0.0 doesn't help. Any ideas? PS! Or maybe I'm must email to TP-Link support?

  Read the article

• Exchange 2010 Mail Enabled Public Folder Unable to Recieve External (anon) e-mail.

  - by Alex

  Hello All, I am having issues with my "Public Folders" mail enabled folders receiving e-mails from external senders. The folder is setup with three Accepted Domains (names changed for privacy reasons): 1 - domain1.com (primary & Authoritative) 2 - domain2.com (Authoritative) 3 - domain3.com (Authoritative) When someone attempts to send an e-mail to [email protected] from inside the organization, the e-mail is received and placed in the appropriate folder. However, when someone tries to send an e-mail from outside the organization (such as a gmail account), the following error message is received: "Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 554 554 Recipient address rejected: User unknown (state 14)." When I try to send an e-mail to the same folder, using the same e-mail address above ([email protected]), but with domain2.com instead of domain3.com, it works as intended (both internal & external). I have checked, double checked, and triple checked my DNS settings comparing those from domain2 & domain3 with them both appearing identical. I have tried recreating the folders in question with the same results. I have also ran Get-PublicFolderClientPermission "\Web Programs\folder" with the following results for user anonymous: RunspaceId : 5ff99653-a8c3-4619-8eeb-abc723dc908b Identity : \Web Programs\folder User : Anonymous AccessRights : {CreateItems} Domain2.com & Domain3.com are duplicates of each other, but only domain2.com works as intended. All other exchange functions are functioning properly. If anyone out there has any suggestions, I would love to hear them. I've just hit a brick wall. Thanks for all your help in advance! --Alex

  Read the article

• Moving Farm to co-location hosting - network settings requirements

  - by Saariko

  I am moving my farm (2 Dell's R620) to a co-location hosting service. I am trying to figure out the secure way to have my network settings The requirements are: VM1 is the working HOST, includes: esxi 5.1, vSphere, 4 clients (w2008r2 all) VM2 has esxi 5.1 installed, and a single machine with Veeam Backup and copy 6.5 - keeping a copy of VM1 clients on the VM2 internal storage (this solution is due to a very small budget - in case of failure on Host 1 - can redirect IP's) Only 2 VM clients require network address and access from the WWAN - ISP provides IP's range for them (with Gateway and DNS) I need connection to the iDrac's from my office (option to create a VPN-SSL tunnel) Connection to the vSphere appliances I want to be able to RDP to the VM clients The current configuration is that each host has the iDrac dedicated nic connected , and another (NIC #1) connected - with a static IP on 192.168.3.x The iDrac's have a static IP from the same network range (19.168.3.x) It will look something like this: My thoughts: On NIC#2 of both hosts I will connected a crossed cable I will give each VM clients that needs internet access a 2ndry VM network with the assigned IP from the ISP open only to web - can not access from the My Question: Should I give IP's (external) to the machines who DO NOT require WWAN Access? - I can't see a way to RDP to them directly if not. Should I use the crossed cable? or just plug NIC #2 to the switch? Will this setup even work? What do I need to verify? What Virtual nic's and/or switches should I create on the Hosts?

  Read the article

• fast way to find network user computer on domain hogging all wan bandwidth

  - by dasko

  i have a network of about 40 domain users and i have huge latency wan issues, like 1400ms for google.com pings. I have noticed that the problem goes away after everyone goes home for the day. I would like to know if i should use something like a hub with wireshark on the router or modem to see if there are any irregular activity. I am open to suggestions but i need to isolate which user has the bug. I am assuming it is either downloads or someone spamming out heavily and not knowing. It would be best to trace to ip number so i can just look into dns and find the pc hostname with the problem? This is the first client i have this problem with so never really needed to address it before but not suprised as users don't actually listen to any best practices that we have suggested. Please help, thanks. just to update, pc's to routers and other computers have ping latency of 1ms so it is right after i hit the wan, using tracert to a web site (random), that i get the massive delay in the responses. As well this is a dsl line with 5mb down and 650kb up (maybe upload saturation?) thanks.

  Read the article

• Can't connect to public WiFi with MacBookPro at coffee shops and libraries

  - by Nathan Bowers

  The Problem: I can't connect to public, unencrypted WiFi at my local public library or Peets Coffee. My Setup: Late 2006 MacBookPro running 10.5.8. I have Parallels installed. It's supposed to work like this: 1) Connect to their unencrypted WiFi network 2) Open a browser which redirects you to their "enter password/agree to terms" page. 3) Browse normally. I can connect to the WiFi network, but when I try to authenticate I always get stuck in a redirect loop. It's been like this for a while. Even before I upgraded to 10.5.8. I never have trouble with encrypted networks or regular open WiFi. What I've tried: Disabling Parallels connections in Network Prefs. Superstition: somehow Parallels installed something in the network stack that's messing me up. Pinging the IP address of the WiFi node I'm connected to. I can ping it, it's there, but I still get stuck in this authentication redirect loop. Tried different browsers, tried different cookie and security settings. Even tried IE under Parallels. No dice. Tried flushing DNS cache. Asked library and coffee employees for help. It didn't go well. My Question: Anybody else have this problem? What should I be looking for?

  Read the article

• Why do I have 55 local area connections in ipconfig?

  - by RMorrisey

  Windows Vista Home Premium. I should mention that I am having no problem whatever getting an internet connection. When I type "ipconfig" in the console, I get (55!) messages of 3 lines each, listing a ton of disconnected network connections. My PC only has one network card. Each message looks like this: Tunnel adapter Local Area Connection* 55: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : These don't cause a major problem; they make it a pain, though, to fish upward and find my IP address. How can I get rid of them? Edit: Actually, a few connection numbers are randomly missing from the sequence; so, it's really more like 30 or 40 connection messages, rather than all 55. Not sure why that is, either.

  Read the article

• VPS with Plesk, one ip, and godaddy (definely need help)

  - by Francesco

  Hi there, here's my situation : i've Plesk 8.3.0 with one IP and i've registered my domains at godaddy.com My problem : i cannot figure out how to configure plesk and godaddy to have my domains (6) properly working into the VPS. i've only one IP, so i can't have my personal NS and need to use godaddy ns. But.. how do i set all the stuff ? I've made a try but it's not working. Please take a look : This is an example of how the domain i'm actually working on is configured On Plesk : Host Record type Value 1.2.3.4 / 24 PTR mydomain.com. ftp.mydomain.com. CNAME mydomain.com. mail.mydomain.com. A 1.2.3.4 ns.mydomain.com. A 1.2.3.4 mydomain.com. NS ns.mydomain.com. mydomain.com. A 1.2.3.4 mydomain.com. MX (10) mail.mydomain.com. webmail.mydomain.com. A 1.2.3.4 www.mydomain.com. CNAME mydomain.com. On godaddy,(Total DNS Control) for the same domain i have this setup : A (Host) Host Points To TTL Actions * 1.2.3.4 1 Hour CNAMES (Aliases) Host Points To TTL Actions e email.secureserver.net 1 Hour email email.secureserver.net 1 Hour ftp @ 1 Hour imap imap.secureserver.net 1 Hour mail pop.secureserver.net 1 Hour mobilemail mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pda mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pop pop.secureserver.net 1 Hour smtp smtp.secureserver.net 1 Hour webmail webmail.secureserver.net 1 Hour www @ 1 Hour MX (Mail Exchange) Priority Host Goes To TTL Actions 10 @ mailstore1.secureserver.net 1 Hour 0 @ smtp.secureserver.net Host Points To TTL Actions @ ns53.domaincontrol.com @ ns54.domaincontrol.com What should i correct ? Thanks for helping me Francesco

  Read the article

• GMail and Yahoo Mail servers not accepting mails from my slicehost slice

  - by Lakshmanan

  Hi, I have a rails in one of the slices at Slicehost. I've setup postfix (sendmail) to send emails from my rails app. All emails to Google Apps domain (to company setup google hosted paid email id) are getting delivered properly (but to spam folder). But all emails to [email protected], [email protected], .. @hotmail.com are not getting delivered and this is the line from my /var/log/mail.log Dec 21 17:33:56 staging postfix/smtp[32295]: 5EB4810545B: to=<[email protected]>, relay=j.mx.mail.yahoo.com[66.94.237.64]:25, delay=1.6, delays=0.02/0.01/1.5/0, dsn=4.0.0, status=deferred (host j.mx.mail.yahoo.com[66.94.237.64] refused to talk to me: 553 Mail from 173.203.201.186 not allowed - 5.7.1 [BL21] Connections not accepted from IP addresses on Spamhaus PBL; see http://postmaster.yahoo.com/errors/550-bl21.html [550]) and this is what i got for gmail Dec 21 17:29:17 staging postfix/smtp[32216]: 0FA3310545B: to=<[email protected]>, relay=gmail-smtp-in.l.google.com[74.125.65.27]:25, delay=0.59, delays=0.02/0.01/0.09/0.47, dsn=5.7.1, status=bounced (host gmail-smtp-in.l.google.com[74.125.65.27] said: 550-5.7.1 [173.203.201.186] The IP you're using to send mail is not authorized 550-5.7.1 to send email directly to our servers. Please use the SMTP relay at 550-5.7.1 your service provider instead. Learn more at 550 5.7.1 http://mail.google.com/support/bin/answer.py?answer=10336 v49si11176750yhc.16 (in reply to end of DATA command)) Please help. I have very little knowledge about setting dns, servers and stuff.

  Read the article

• NIS user not being added to NIS group

  - by Brian

  I have set up a NIS server and several NIS clients. I have a user and a group on the NIS server like so: /etc/passwd: myself:x:5000:5000:,,,:/home/myself:/bin/bash /etc/group: fishy:x:3001:otheruser,etc,myself,moreppl I imported the users and groups on the NIS client by adding +:::::: to /etc/passwd and +::: to /etc/group. I can log in to the NIS client, but when I run groups, fishy is not listed. But getent group fishy shows that it was imported correctly and lists me as a member. And if I do sudo su - myself, then suddenly groups says I am in the group! I also had nscd installed, and the groups worked correctly for a while. It seemed like after being logged in for a while, I would silently be dropped out of the group. If I restarted nscd and logged in again, then the groups worked correctly...for a while. There are no UID or GID conflicts with local users or groups. Update: Contents of /etc/nsswitch.conf: passwd: compat group: compat shadow: compat hosts: files nis dns networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis aliases: nis files

  Read the article

• OpenVPN bad source address from client

  - by Bogdan

  I have one problem with OpenVPN. There are a lot drops records in the openvpn log file on the server: Mon Oct 22 10:14:41 2012 us=726541 laptop/???:1194 MULTI: bad source address from client [192.168.1.107], packet dropped grep -E "^[a-z]" server.conf ----- port 1194 proto udp dev tun ca data/ca.crt cert data/server.crt key data/server.key dh data/dh1024.pem tls-server tls-auth data/ta.key 0 remote-cert-tls client cipher AES-256-CBC tun-mtu 1200 server 10.10.10.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" client-to-client client-config-dir /etc/openvpn/ccd route 10.10.10.0 255.255.255.0 keepalive 10 120 comp-lzo persist-key persist-tun max-clients 5 status /var/log/status-openvpn.log log /var/log/openvpn.log verb 4 auth-user-pass-verify /etc/openvpn/verify.sh via-file tmp-dir /tmp script-security 2 ----- cat ccd/laptop ----- iroute 10.10.10.0 255.255.255.0 ----- cat client.conf ----- remote server ip 1194 client dev tun ping 10 comp-lzo proto udp tls-client tls-auth data/ta.key 1 pkcs12 data/vpn.laptop.p12 remote-cert-tls server #ns-cert-type server persist-key persist-tun cipher AES-256-CBC verb 3 pull auth-user-pass /home/user/.openvpn/users.db ----- According to "Jan Just Keijser - OpenVPN 2 Cookbook" root of the problem is incorrect config options.see the screenshot But, as you see, my config has such options. Could you please help me to solve this problem. @week Verb leverl=6; client log. Mon Oct 22 16:06:02 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Mon Oct 22 16:06:02 2012 /sbin/ifconfig tun0 10.10.10.3 pointopoint 10.10.10.5 mtu 1500 Mon Oct 22 16:06:02 2012 /sbin/route add -net xxxx netmask 255.255.255.255 gw 192.168.1.1 Mon Oct 22 16:06:02 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 Initialization Sequence Completed cat ccd/latop iroute 10.10.10.0 255.255.255.0 ifconfig-push 10.10.10.3 10.10.10.5

  Read the article

• SSL in IIS 7 on a subdomain in a web farm

  - by justjoshingyou

  I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

  Read the article

• Running two different websites domains one one IP address

  - by Akshar Prabhu Desai

  Here is my apache configuration file. I have two domain names running on same ip but i want them to point to different webapps. But in this case both point to the one intended for e-yantra.org. If I copy paste akshar.co.in part before E-yantra.org both start pointing to akshar.co.in I have two A DNS entries (one per domain name) pointing to the same IP. NameVirtualHost *:80 <VirtualHost *:80> ServerName www.e-yantra.org ServerAdmin [email protected] DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> <Directory /var/www/ci/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> <Directory /var/www/db2/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> <VirtualHost *:80> ServerName www.akshar.co.in ServerAdmin [email protected] DocumentRoot /var/akshar.co.in <Directory /var/akshar.co.in/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost>

  Read the article

• Setup a new domain controller over a temporary VPN, but now Windows delays startup?

  - by Kris Anderson

  I'm migrating servers from colo locations to Amazon's VPC EC2 instances. If anyone hasn't worked with Amazon VPC before, VPN is a pain in the arse! Anyways, I setup a new server that acts as the domain controller for our Amazon VPC. In order to migrate all the user accounts from our existing domain controllers I manually connected to our colo VPN using my user account on the new Amazon EC2 machine. I was able to join the domain and the new Amazon server became another domain controller on our network. So far so good. The problem I'm having is that when booting the EC2 domain controller (which is no longer connected to the VPN so it can't communicate with the existing controllers), it takes a good 6-8 minuted before I can remote into the server (instead of the 1-2 minutes it should take). Also, during this time most of the services we also run (like IIS) also give 404 errors until the 6-8 minutes have passed. It's almost like the domain controller is attempting to reach the other domain controllers first and after 6-8 minutes it falls back to the one located on the local machine? I don't think that's what's happening though, because Server 2008 R2 doesn't have primary and backup domain controllers. They're all equal as far as Windows is concerned. For my network adapter I have only one DNS listed, 127.0.0.1, so it should be looking up the local domain controller and not the other domain controllers it connected to over VPN when VPN was enabled. In the server logs I'm seeing these warnings pop up during a reboot: The winlogon notification subscriber is taking long time to handle the notification event (CreateSession). The winlogon notification subscriber took 409 second(s) to handle the notification event (CreateSession). Any ideas on what's happening here? I would try removing the existing domain controllers from the new Amazon EC2 machine, but I still need to connect over VPN a few times to migrate some data between the servers, and I don't want that change being reflected back to the other domain controllers in our colo locations.

  Read the article

• Streaming to PS3 with NAS and built-in dlna server?

  - by philt

  With consumer-grade hardware, is it possible to successfully stream 1080p mp4 videos to a PS3? I have a linksys router that can only do 10/100. The PS3 is wired to it with cat5e cable, and the PS3 itself supports gigabit ethernet. I would upgrade the router and get one that supports gigabit ethernet if it could handle streaming like this. It currently does work with minor jerkiness streaming from my mac to the PS3, but fast-forward/reverse and "goto" (equivalent of scene selection) take forever and/or fail completely. And streaming from my mac of course requires the mac to be on at all times. When I put the movies on an external USB drive and connect to the PS3 directly, it performs flawlessly. Fast forward and everything works great. So I was thinking about getting a NAS, but I don't know if any inexpensive NAS (i.e. Buffalo Linkstation Live, WD My Book World Edition, D-Link DNS-321, etc.) can actually deliver the performance necessary to do this, even with gigabit ethernet?

  Read the article

• How to use Python to read the physical address(MAC ID) [closed]

  - by getjoefree

  I want to read the physical address of the NIC model, i can get the results that i want to with SED.EXE before, but SED.EXE does not support my environment but Python ok, who have the means to do it. The general situation (not plug the network cable, it is impossible to obtain IP address): Ethernet adapter: Connection-specific DNS Suffix.: Chianet Description ...........: Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller Physical Address .........: A4-BA-DB-9D-1E-8E Dhcp Enabled ...........: Yes Autoconfiguration Enabled ....: Yes Ethernet adapter 3: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1510 Wireless-N WLAN Mini-Card Physical Address. . . . . . . . . : 00-23-4D-D9-C0-28 The description of the NIC different, we can use this to fetch the corresponding physical address, base on Physical Address does not work, because the computer with the WLAN Card, I want to use Python to read my computer the card information and after Python handles an output file, output file format: SET MAC = A4BADB9D1E8E and sed format: ipconfig -all|sed -nrf getmac.sed | sed -e "s/-//g" > WINMAC.BAT getmac.sed: /Marvell Yukon 88E8040/ { n; s/.*: ([-0-9A-F]+)/set winmac=\1/p; }

  Read the article

• Is the sysadmin/netadmin the defacto project planner at your organization?

  - by gft74

  At my company it has somehow over the past few years slowly become my job to come up with a project plan, milestones and time lines for deployment of developer applications. Typical scenario: My team receives a request for a new website/db combo and date for deployment. I send back a questionnaire for the developer to fill out on all the reqs for the site (ssl? db? growth projections etc.) After I get back all the information, the head of development wants a well developed document of what servers will it live on why those servers what is the time line for creating the resources step-by-step SOP for getting the application on the server and all related resources created (dns, firewall, load balancer etc.) I maybe just whining but it feels like this is something better suited to our Project Management staff (which we have) or to the developer. I understand that I need to give them a time-line on creating the resources, but still feel like this is overkill. We already produce documentation on where everything lives and track configuration changes to equipment. How do other sysadmin folks handle this?

  Read the article

• How do I get "Back to My Mac" (using MobileMe) from Windows?

  - by benzado

  I have a MobileMe subscription and a Mac at home with "Back to My Mac" enabled. When I'm away from home, this service lets me use another Mac to connect to my Mac back home and access file sharing, screen sharing, etc. As far as I know, the service doesn't use any proprietary protocols, so in theory I should also be able to get "Back to My Mac" from a Windows PC. This MacWorld article explains how it works. Basically, it uses Wide-Area Bonjour to give your Mac a domain name like hostname.username.members.mac.com. Remote computers can find your Mac using that address, then connect to it using a private VPN. The "Wide Area Bonjour" part seems to make it a little more complicated than simply a regular domain name, though. Note that I'm not interested in using the methods described by LifeHacker, which doesn't use the MobileMe service at all. I don't want to use a totally different dynamic DNS service. I'd like to use the one I'm already paying for, or at least find out why that's not possible from Windows. Also, my primary problem is finding a network route back to my mac... once I've got that I know how to enable services so that Windows can talk to it. UPDATE: Based on some additional research, it appears that Apple is only assigning IPv6 addresses to the hostname.username.members.mac.com names. So any solution will require enabling IPv6 support on Windows, if possible.

  Read the article

• What does a DHCP-client consider to be the "best" answer?

  - by Nils

  We have training rooms where normally Windows XP is installed (via PXE). The "normal" DNS/DHCP infrastructure are Windows-Servers. The training room has its own VLAN (different from the Windows servers), so there is most propably an IP helper for DHCP requests active on the Cisco router where all PCs from that room are connected to. Now we wanted to convert some of the PCs to Linux instead. The idea was: Put our own Laptop with a DHCP server into the VLAN of the room and override the "normal" DHCP response. The idea was that this should work, since a directly attached DHCP server in that VLAN should have a faster response-time than the "normal" DHCP server located some hops away from that VLAN. It turned out that this did not work. We had to manually release the lease on the original DHCP server to get it working. On the Laptop we did see the client requesting the IP and "our" dhcp was sending NACKs to the Windows IP request, before that we did offer our own response. Old Question: Why did this not work out as expected? What is making the PC regain its old lease? Update 2012-08-08: The regain-issue has been explained in the DHCP-RFC. Now this explains why the PC regains its old lease. Now we do release the IP from the Windows-DHCP-server before giving it another try. Again - the Windows-DHCP-server wins. I suspect that there is some algorithm for the dhcp-client which determines the "best" dhcp-answer for the client. The new question is: How does the client choose the "best" answer?

  Read the article

• Domain joined computer unable to access servers through VPN

  - by kscott

  Our servers are in a virtual off site hosting center, our office has a vpn connection to the data center, but for reasons I don't understand we also have to connect to the Citrix Access Gateway (CAG) client in order to access the servers. I am a programmer with rather limited ops knowledge including a weak grasp of networking and terminology. Bear with me. I was just given a new laptop, which is a 64 bit Windows 7 system unlike my previous 32 bit Windows XP desktop which was able to connect without issue. My laptop has been joined to the domain so that I login with my AD credentials, I am able to connect to the CAG and get authenticated, and after doing this I can ping our servers and they resolve to the correct internal IP addresses, but I am unable to use remote desktop to the servers, connect to SQL servers through my local SQL Management Studio, navigate to them through the file system, or view any of our internal intranet websites. All of which I was able to do previously. I have tried turning off my Windows firewall and the problem remains, the DNS servers are set to the correct IPs of our domain controllers, and the ops guys here are a little stumped. Does any one have any suggestions?

  Read the article

• Apache2 VirtualHost on Debian not working

  - by milo5b

  I am having some problems with Apache2 configuration. I have already tried to look for documentation on the web (Apache's site, Debian's site, here on serverfault, etc), but nothing really helps. I have tried different configurations, but my current configuration is the following (/etc/apache2/sites-available/default): <VirtualHost *:80> ServerAdmin [email protected] ServerName mysite.dev ServerAlias mysite.dev DocumentRoot /var/www/mysite.dev/httpdocs/ ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] ServerName livesite.com ServerAlias www.livesite.com DocumentRoot /var/www/livesite.com/httpdocs/ <Directory /var/www/livesite.com/httpdocs/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> mysite.dev it's just an entry in hosts file on my client machine, while livesite.com it's an actual DNS record which would resolve to the same IP as the IP set in hosts file for mysite.dev. The problem is that when i try to type mysite.dev in my browser, it would automatically go to livesite.com. I tried to have different /etc/apache2/sites-enabled/ files (/etc/apache2/sites-enabled/mysite.dev , /etc/apache2/sites-enabled/livesite.com ) - and of course with the actual sites-available related files, but achieving the same results. I have tried to have a peak on error.log and access.log but there's nothing I can see. My httpd.conf contains: AccessFileName .htaccess And I have no /etc/apache2/conf.d/virtual.conf file. Any help would be greatly appreciated - if I did not provide enough info please let me know I will do my best to provide all necessary info. Thanks

  Read the article

• Windows - Website unaccessible only on windows pcs in LAN

  - by DorentuZ

  For serveral days now, a website isn't accessible on a single pc in the LAN. On the other pc's, it works just fine. And it's just a single website that's not accessible as far as I know of. The website generates a timeout on every single web browser I've tried (IE8, Firefox and Chrome). However, traceroute, nmap and telnet all work just fine. I've even tried multiple user accounts and safe mode, but that didn't work either. As a side note: using a linux live cd did work and I could access the website without any problems. The hosts file is the windows default, the ip- and dns settings on the network adapter normal as well. No strange processes are running and no viruses found. According to tcpview and netstat there are connections to the domain, but every request in the browser results in a timeout.. Any idea what's happening? Update: All of the computers on the network running Windows (any version) are showing this problem now. The website is still working under linux and mac osx. So, it has to be related to some kind of windows update (although I haven't installed any on one computer in the past week, which I've set to do manual updates only)..

  Read the article

• Proper Network Infastructure Setup DMZ, VPN, Routing Hardware Question

  - by NickToyota

  Greetings Server Fault Universe, So here's a quick background. Two weeks ago I started a new position as the systems administrator for an expanding health services company of just over 100 persons. The individual I was replacing left the company with little to no notice. Basically, I have inherited a network of one main HQ (where I am situated) which has existed for over 10 years, with five smaller offices (less than 20 persons). I am trying to make sense of the current setup. The network at the HQ includes: Linksys RV082 Router providing internet access for employees and site to site VPN connecting the smaller offices (using an RV042 each). We have both cable and dsl lines connected to balance traffic (however this does not work at all and is not my main concern right now). Cisco Ironport appliance. This is the main gateway for our incoming and outgoing emails. This also has an external IP and internal IP. Lotus domino in and out email servers connected to the mentioned Cisco gateway. These also have an external IP and internal IP. Two windows 2003 and 2008 boxes running as domain controllers with DNS of course. These also have both an external IP and internal IP. Website and web mail servers also on both external and internal IPs. I am still confused as why there are so many servers connected directly to the internet. I am seriously looking to redesign this setup with proper security practices in mind (my highest concern) and am in need of a proper firewall setup for the external/internal servers along with a VPN solution about 50 employees. Budget is not a concern as I have been given some flexibility to purchase necessary solutions. I have been told Cisco ASA appliance may help. Does anyone out in the Server Fault Universe have some recommendations? Thank you all in advance.

  Read the article

• Emails sent through SMTP on VPS are considered to be spam

  - by Ilya

  During our business we have to make regular mailing to our clients: invoices, information emails, etc. Previously we received and sent emails using mail server of our hosting provider. But as the number of clients increased, we have to order VPS and install our own SMTP server their for performing our mailings. So, now we have default provider mail server for receiving emails, let it be business.com. We have email accounts like [email protected], etc. We use this mail server to receive emails and manage our email accounts. And we have SMTP server which is running on VPS. We use this SMTP only for sending emails with From addresses like [email protected]. VPS has default DNS records created by provider, let it be IP.AD.RE.SS <- ip-ad-re-ss.provider.com. Mailings are made using either desktop email clients or custom Java-based application which uses JavaMail for sending emails. The problem is that most of emails sent by us are placed in spam folders in clients email accounts. Clients have their email in Gmail, Yahoo, Hotmail, etc. Could you please tell what is the most probable reason and solution of described problem? Are there any service in Intranet where we can send test email and get an answer with description why this email could be considered to be spam?

  Read the article

• Basic Apache setup is not seeing my site

  - by Jakobud

  Sorry that is a horrible thread subject, but I cannot think of a better more descriptive subject. We are running a Fedora 11 server that is currently hosting some CRM on it. I want to use a VirtualHost directive to add another site to the server. So I created this conf: /etc/httpd/conf.d/mysite.ourdomain.com.conf And here is the content: <VirtualHost *:80> ServerName mysite.ourdomain.com DocumentRoot /www/mysite ServerAdmin [email protected] ErrorLog /var/log/mysite.ourdomain.com-error.log CustomLog /var/log/mysite.ourdomain.com-access.log common </VirtualHost> I restarted apache, getting the following warning: [warn] NameVirtualHost *:80 has no VirtualHosts From what I read, this warning is not related and I can ignore it and my site should still be up and running, correct? (I'll troubleshoot this error later if so) Well I have our DNS server setup to point mysite.ourdomain.com to goto this server. I can ping it and it points to the correct LAN IP, etc.. Now when I try to access it in the browswer I get nothing. It just says Connecting... and never gets there. If I try mysite.ourdomain.com or the IP address, neither one doesn't get there. It's a very simple and basic apache setup so I'm not sure what I'm doing wrong... Like I said, the other thing that is running on this server is a crm and it's .conf looks something like this: Listen x.x.x.x:443 <VirtualHost x.x.x.x:443> ServerAdmin [email protected] ServerName crm.ourdomain.com ErrorLog /var/log/httpd/ourdomain/crm-error.log CustomLog /var/log/httpd/ourdomain/crm-access.log common DocumentRoot /www/ourdomain/crm <IfModule mod_dir.c> DirectoryIndex /index.php </IfModule> </VirtualHost> There is also some LDAP authentication stuff in that config but I left it out cause I assumed it wasn't necessary to post. Anyone have any clue where I should start or what settings I can post from httpd.conf that would help?

  Read the article

• Subdomains and address bar

  - by Priednis

  I have a fairly noob question about how subdomains work. As I understand at first the DNS server specifies that a request for certain subdomain.domain.com has to go to the IP address of domain.com, and the webserver at domain.com further processes the request and displays the needed subdomain page. It is not entirely clear to me how (for example Apache) server does it. As I understand there can be entries in vhosts.conf file which specify folders that contain the subdomain data. Something like: <VirtualHost *> ServerName www.domain.com DocumentRoot /home/httpd/htdocs/ </VirtualHost> <VirtualHost *> ServerName subdomain.domain.com DocumentRoot /home/httpd/htdocs/subdomain/ </VirtualHost> and there also can be redirect entries in .htaccess files like rewritecond %{http_host} ^subdomain.domain.com [nc] rewriterule ^(.*)$ http://www.domain.com/subdomain/ [r=301,nc] however in this case the user gets directed to the directory which contains the subdomain data but the user gets "out" of the subdomain. I would like to know - how, when going to subdomain.domain.com the subdomain.domain.com, beginning of address remains visible in the address bar of the explorer? Can it be done by an alternate entry in .htaccess file? If a VirtualHost entry is specified in the vhosts.conf file, does it mean, that a new user account has to be specified for access to this directory?

  Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >