Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 187/343 | < Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >

  • Killing CLOSE_WAIT sockets without killing parent process on Linux

    - by Alex Neth
    Tomcat is leaving me with CLOSE_WAIT sockets which ultimately saturate the maximum number of connections. I've tried many methods in my client and server code to get rid of these to no avail, including closing connections, calling System.gc(), etc. Now I'm trying to find a way to simply time these out quickly in the OS. I've got conntrack working, but am not sure how to use that to kill these connections. I've also set /proc/sys/net/ipv4/netfilter/ip_conntrack_tcp_timeout_close_wait to 1, which of course is too low but the connections persist. Is there a way to kill these zombie sockets? Running Ubuntu.

    Read the article

  • DHCPD (Slackware) - Disabling auto-generation of gateway as DNS server

    - by Dogbert
    Good day, I am using a Linux workstation on Slackware 13.37. One "problem" I have had to deal with ever since 11.0 is the following: DNS servers are queried and determined at startup by DHCP daemon (DHCPD) This is invoked at startup by a script located at /etc/rc.d/rc.dhcpd My DNS servers for my ISP are resolved correctly, and are stored in a list located at /etc/resolv.conf However, the one annoying problem is that my gateway IP (ie: 192.168.1.1) is always automatically put at the top of the list in resolv.conf, meaning I have to always wait for a timeout before a valid DNS server is used to resolve an address (ie: timeout on 192.168.1.1 because it is not actually a DNS server, then DHCP uses the next server in the list). I could lower my DNS resolution timeout so the gateway query times out quicker, but that's not what I want, as I don't want to degrade the abilities of legitimate DNS servers. What I would like to do is change how DHCPD operates so that it does NOT put my gateway IP address at the beginning of this list. I've searched via "man dhcpd", etc, and haven't found the exact answer yet. Any help on this issue is appreciated. Thank you all in advance for your time and assistance.

    Read the article

  • very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

    - by gojira
    I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

    Read the article

  • Colocation and HSRP setup

    - by WinkyWolly
    My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN. However I'm confused as to how to the IP setup should work. Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment. What's the proper way to do this?

    Read the article

  • A router that supports connecting with 2 different wifi networks

    - by Allan Deamon
    I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

    Read the article

  • Finding Missing UDP Frames Using Wireshark + Custom Dissector (for CQS)

    - by John Dibling
    How do you use Wireshark to identify missing UDP frames? I have written a custom dissector for the CQS feed (reference page). One of our servers gaps when receiving this feed. According to Wireshark, some UDP frames are never received. I know that the frames were sent because all of our other servers are gap-free. A CQS frame consists of multiple messages, each having its own sequence number. My custom dissector provides the following data to Wireshark: cqs.frame_gaps - the number of gaps within a UDP frame (always zero) cqs.frame_first_seq - the first sequence number in a UDP frame cqs.frame_expected_seq - the first sequence number expected in the next UDP frame cqs.frame_msg_count - the number of messages in this UDP frame And I am displaying each of these values in custom columns, as shown in this screenshot: A typical CQS log will consist of millions of rows, so I can't just eyeball it. Is there any way I can get Wireshark to tell me which frames are missing?

    Read the article

  • Ubuntu 9.04 Cannot Connect to visible open wifi ap (reason 6)

    - by Andrew Bolster
    I'm travelling currently so the last network i connected successfully to was my home wpa-psk network. I hadn't tried anything until i got to my accommodation that is an open network (that I'm on now on the Win7 partition on my laptop). The network (and a similar archetypical 'linksys' open network, aswell as some protected local networks are correctly displayed in network-manager and upon selection, it happily spins around to its hearts content for a while before saying 'no chance boy'. /var/log/syslog spills out the usual combination of wpa_supplicant and kernel messages, the most interesting of are that the kernel deauthentication reason 6 response. 6 apparently means class2FrameFromNonAuthStation...Client attempted to transfer data before it was authenticated. Anyone seen anything like this? I've already tried going closer to the router to no avail. I don't remember seeing this any other time I've connected to a open AP, even if that AP is far away. (Signal strength for this AP is good, kismet says its around -57dBm, well above the threshold of -80dBm, and I've tried all the suggestions from the 'Related Questions'

    Read the article

  • Why can't my networks reach each other?

    - by HOLOGRAPHICpizza
    We have two Buffalo WZR-HP-G300NH2 routers, with the default firmware, DD-WRT v24SP2-MULTI (10/31/11) std - build 17798. Each has a separate cable internet connection with a public static IP address. They are both in the 24.123.68.0/24 space. Both of them can contact pretty much the whole internet, and they can both be accessed out on the internet with no problem, but for some reason they can't talk to each other! When I try to ping one from the other I always get "Destination Host Unreachable". There are no strange routing or firewall rules in place. And they are both set to respond to pings, I can ping them from outside. Our main IT guy is going to call our ISP on Monday, but I'm impatient, so does anyone have any ideas?

    Read the article

  • Hooking up a multifunction printer via network and USB

    - by C-dizzle
    I have a Dell 2155CDN Multifunction printer that is hooked up through our network. But when using the scan feature, it is terribly slow, and I assume it has something to do with it scanning through the network port. Is it possible to leave the printer hooked up across the network, but also attach it to a computer via USB just for the scanner? Or would doing this confuse the printer not knowing which port to use for each feature?

    Read the article

  • Routing Traffic on Ubuntu to give Raspberry PI Internet Access

    - by Scruffers
    I'm hoping someone can point me in the right direction for setting up my Linux (Ubuntu 12.04) box to route traffic from eth0 to wlan0. I'll try and explain the problem I am trying to solve: I currently have two separate networks: [RaspberryPi/eth0] 192.168.2.2 / 255.255.255.0 ^ | v [Ubuntu/eth0] 192.168.2.1 / 255.255.255.0 And: [Ubuntu/wlan0] 192.168.1.100 / 255.255.255.0 ^ | v [ADSL router] 192.168.1.1 / 255.255.255.0 So currently if I want to access the RaspberryPI I can SSH from the Ubuntu box to the PI. And if I want to use the Internet, I have full access from the Ubuntu box, but nothing from the RaspberryPI - the two networks are partitioned. What I would like to do is configure things so that the RaspberryPI has Internet access via the Ubuntu box and out to the Internet. I tried to create a bridge, but got the message "wlan0: operation not supported" (wireless chipset is Ralink RT3062). I'm sure giving the Raspberry PI Internet access should be easy to do in this configuration, but I am a bit lost - can someone point me in the right direction please?

    Read the article

  • Remote Desktop fails after VPN connection

    - by Samet Sorgut
    The local computer (comp 1) is connected to a remote computer (comp 2) with Remote Desktop. On the remote computer (comp 2), I try to establish an VPN connection to a different remote computer (comp 3). Once I try to establish the VPN connection from the remote computer (comp 2) to the second remote computer (comp 3), Remote Desktop freezes on comp 1. It is not possible to connect to comp 2 again via Remote Desktop. What can be done to connect to this remote computer (comp 2) after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest? EDIT: I want to use the internet connection of the VPN, so all traffic should go over the VPN but still RDP working. My IP: 100.0.0.1 The IP where I'm connecting via RDP: 200.0.0.20 (Mask: 255.255.255.192, Gateway: 200.0.0.193) Where the 200.0.0.1 connects to VPN the IP of the VPN is: 65.254.61.250 Will routing like this help (Command is issued in 200.0.0.20, the RDP location): route ADD 65.254.61.250 MASK 255.255.255.192 200.0.0.193 Couldn't add gives the error: The route addition failed: The parameter is incorrect. I tried before connecting to VPN.

    Read the article

  • how do I set up a virtual host (it's not working, and I've done everything right)

    - by piratepartypumpkin
    My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

    Read the article

  • Servers / ram for social network- how many?

    - by Marty
    I am launching my social network soon an looking into hosting. The question i am lost is: Do i need separate servers for web vs database vs image handling since there is photo sharing? Or does 1 server handle it all? Also is more ram better? If i get 50GB ram is that better than having 8 gb ram? EDIT: It is PHP codeignitor and MySQL for now. (switch to NoSQL DB later if demand calls fr it.) I will be using memcache also. Concept wise it is similar to yelp, so geographic based with lots of user content and image sharing + live feeds an privacy levels. User plan is open question. Without testing the demand for this i cant give a number. But the concept is unique, no one out there with the set of features i am releasing so it could grow. Ideally I want to plan for handling about 1-2 million views / month from launch. If it goes more than that then I will upgrade.

    Read the article

  • Port forwarding with multiple IP's

    - by Jon
    I work at a company which uses a Fortigate 60 router, something I'm not really familiar with. Everything worked fine with it until a week ago when Comcast came in and replaced our modem. It seemed as though the process went smoothly - our connection came back up and our static IP remained the same. However, none of our port forwarding is working. What has me confused is the Comcast modem apparently has two IP addresses. The WAN2 interface for it in the Fortigate router is set to 10.1.10.10. However, all of our port forwarding settings are set to an external IP address of 10.1.10.50. Now this setup used to work fine, so something with the Comcast modem must have changed. How can I find out what? I tried setting a computer to a local IP of 10.1.10.15 so I could open up the web interface for the modem, but I can't even ping 10.1.10.10 when I do that. Any ideas? Thanks!

    Read the article

  • How to connect 2 routers (Asmax and D-link)

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • VMware server 2.0 SYN/ACK repeating issues

    - by user65579
    VMWare Server 2.0.0 Build 122956 I am having some issues with connecting into a guest VM (Ubuntu linux 4.4.3-4 lucid) running under VMware 2.0 on a windows server host. All connections to and from the VM's work fine, except for FTP. I thought the issue was the FTP daemon at first but it has been ruled out that it is not the daemon or the server itself. When you try to connect to the FTP server from outside of the host OS it fails with a "421 Service not available" but when you try and connect from the local VM or from the host OS the connection goes through fine. I have ran many packet sniffs using wireshark/tcpdump from the VM, the host OS, and the client connecting, the most informative is the host OS. I have attached a PNG of the relavant packets that were captured. I viewed some other network traffic that was sniffed (WWW specifically) and it seems to do the same syn/ack repeating but the user doesnt see any issues. I have disabled the firewall and the issues persisits, I have tried with specific allow rules to ensure the data is allowed and no changes. It appears like VMware attempts to do the ICMP redirect and it works, but then it vmware repeats the packets sent so you get 3 syn/ack's for every one syn from the client. Also VMWare appears to be attempting to establish an FTP connection between the HOST OS and the GUEST OS, because I see the second SYN sent from the HOST OS to the GUEST to initiate a new connection, and it get the appropriate SYN/ACK followed by an ACK, but the client never sees any of this from its end. EG. syn from client syn/ack from host OS to client syn/ack from guest OS to client syn/ack from host OS to client The same thing happens when the connection reset is attempted, RST's start being sent and repeated, the server responds with a valid header to continue the FTP handshake but the RST acknowledgement is allready issued and things are closed. I am not 100% if this is a bug in VMware or possibly a VMNetwork missconfiguration. Does anyone have any thoughts on where exactly the issue could be, things to try to verify or rule out? I have linked to a picture of the relevant packets sniffed from the host OS. http://img18.imageshack.us/img18/7789/vmwareftpconnection.jpg

    Read the article

  • Cisco redundancy modes

    - by user974896
    I am using a Cisco 6500 series with an SSO redundancy configuration. The show redundancy output is as follows: Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = rpr Maintenance Mode = Disabled Communications = Up I would assume the device is operating in RPR mode although SSO is configured. What could cause this? Shouldn't the operating mode be SSO? EDIT (show redundancy states): my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit = Primary Unit ID = 5 Redundancy Mode (Operational) = rpr Redundancy Mode (Configured) = sso Redundancy State = rpr Split Mode = Disabled Manual Swact = Enabled Communications = Up client count = 60 client_notification_TMR = 30000 milliseconds keep_alive TMR = 9000 milliseconds keep_alive count = 1 keep_alive threshold = 18 RF debug mask = 0x0

    Read the article

  • Network on linux server is periodically down

    - by Fabian
    I have an old server running Fedora 4 that occasionally just stops responding via network for about an hour. This happens 1-2 times a week. Also no connection from the server itself to any other computer on the network is possible when it happens. The network settings and routes look fine. There are no unusual log messages and no unusual processes running at that time. If I restart the network or just do an ifconfig eth0 down & ifconfig eth0 up it works fine afterwards. I know that the server should be updated to a currently supported OS, but that is not really an easy option right now. Any ideas on how I could diagnose and fix that problem?

    Read the article

  • Prevalence of WMI enabled in real Windows Server networks

    - by TripleAntigen
    Hi I would like to get opinions from systems administrators, on how common it is that WMI functionality is actually enabled in corporate networks. I am writing an enterprise network application that could benefit from the features of WMI, but I noted after creating a virtual network based on Server 2008 R2, that WMI seems to be disabled by default. Do systems admins in practical corporate networks enable WMI? Or is it usually disabled for security purposes? What is it used for if it is enabled? Thanks for any advice! MORE INFO: I should have said, I really need to be able to query the workstations but I understand that by default the WMI ports on Win7 and XP firewalls (at least) are disallowed, so do you use some sort of group policy or other method to leave a hole open for WMI on the workstations? Or is just the servers that are of interest? Thanks for the responses!!

    Read the article

  • Switch to IPv6 and get rid of NAT? Are you kidding?

    - by Ernie
    So our ISP has set up IPv6 recently, and I've been studying what the transition should entail before jumping into the fray. I've noticed three very important issues: Our office NAT router (an old Linksys BEFSR41) does not support IPv6. Nor does any newer router, AFAICT. The book I'm reading about IPv6 tells me that it makes NAT "unnecessary" anyway. If we're supposed to just get rid of this router and plug everything directly to the Internet, I start to panic. There's no way in hell I'll put our billing database (With lots of credit card information!) on the internet for everyone to see. Even if I were to propose setting up Windows' firewall on it to allow only 6 addresses to have any access to it at all, I still break out in a cold sweat. I don't trust Windows, Windows' firewall, or the network at large enough to even be remotely comfortable with that. There's a few old hardware devices (ie, printers) that have absolutely no IPv6 capability at all. And likely a laundry list of security issues that date back to around 1998. And likely no way to actually patch them in any way. And no funding for new printers. I hear that IPv6 and IPSEC are supposed to make all this secure somehow, but without physically separated networks that make these devices invisible to the Internet, I really can't see how. I can likewise really see how any defences I create will be overrun in short order. I've been running servers on the Internet for years now and I'm quite familiar with the sort of things necessary to secure those, but putting something Private on the network like our billing database has always been completely out of the question. What should I be replacing NAT with, if we don't have physically separate networks?

    Read the article

  • ipv6 with KVM on debian

    - by Eliasdx
    I have trouble setting up IPV6 on my Proxmox (KVM) server: My ISP sent me this information(xxx=placeholder): IPs: 2a01:XXX:XXX:301:: /64 Gateway: 2a01:XXX:XXX:300::1 /59 This is the interface setup on the host server: auto vmbr1 iface vmbr1 inet static address 178.XX.XX.4 broadcast 178.XX.XX.63 netmask 255.255.255.192 pointopoint 178.XX.XX.1 gateway 178.XX.XX.1 bridge_ports eth0 bridge_stp off bridge_fd 0 iface vmbr1 inet6 static address 2a01:XXX:XXX:301::2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del 2a01:XXX:XXX:300::1 dev vmbr1 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev vmbr1 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev vmbr1 On the guest: auto eth0 iface eth0 inet static address 178.xx.xx.47 netmask 255.255.255.255 broadcast 178.xx.xx.63 gateway 178.xx.xx.1 pointopoint 178.xx.xx.1 iface eth0 inet6 static pre-up modprobe ipv6 address 2a01:XXX:XXX:301::2:2 netmask 64 up ip -6 route add 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del 2a01:XXX:XXX:300::1 dev eth0 up ip -6 route add default via 2a01:XXX:XXX:300::1 dev eth0 down ip -6 route del default via 2a01:XXX:XXX:300::1 dev eth0 Ipv4 works on both host and guest but Ipv6 only works "sometimes". It's up for minutes and then down again until I change something. However I can actually ping the host and the guest from both host and guest. host:~# ip -6 neigh 2a01:XXX:XXX:301::100:2 dev vmbr1 lladdr 00:50:56:00:00:e0 REACHABLE 2a01:XXX:XXX:300::1 dev vmbr1 lladdr 00:26:88:76:18:18 router STALE host:~# ip -6 route 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 2a01:XXX:XXX:301::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev vmbr1 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev tap101i1d0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via 2a01:XXX:XXX:300::1 dev vmbr1 metric 1024 mtu 1500 advmss 1440 hoplimit 4294967295 Does someone know why it isn't working? And is there a way to configure multiple v6 IPs from the same subnet so I can dedicate IPs to websites on a server with multiple virtualhosts?

    Read the article

  • Improve wireless performance

    - by djechelon
    Hello, I have a Trust Speedshare Turbo Pro router, which is running on channel 6. I found that the wireless signal (and network performance) dramatically drops from my PDA (I can barely attach to the network, even if I set the PDA's energy settings to maximum wireless performance) when I even exit my room, and I don't have shielded walls or something like that. I can't even stream a SD video from my desktop (connected via LAN) to my laptop using WiFi, while via LAN it works fine. I read that changing router's channel could improve performance due to interference reducing. I found that almost all wireless networks around here run on channels 6 and 11. I tried to go to my router's settings page to change channel, but I found that the combo box only allows me to select 6!! I'm not sure, but I may have been able in the past to change channel, though not to all of the available channels. A few minutes ago I tried a firmware upgrade, but it didn't solve my problem. My question is Is it possible that my router is someway locked to its channel? I bought it on my own, I didn't receive it from my ISP Apart from boosting the antenna power to the maximum (which, by the way, increases the EM radiation my and my family's bodies absorb 24/7 and is little more environment-unfriendly), do you have any tips on getting high quality transmission up to 5 metres from the antenna? Thank you

    Read the article

  • What would cause Memcached to Hang for 2+ seconds?

    - by Brad Dwyer
    I'm going nuts trying to scale memcached. From their site: Memcached operations are almost all O(1). Connecting to it and issuing a get or stat command should never lag. If connecting lags, you may be hitting the max connections limit. See ServerMaint for details on stats to monitor. If issuing commands lags, you can have a number of tuning problems. Most common are hardware problems, not enough RAM (swapping), network problems (bandwidth, dropped packets, half-duplex connections). On rare occasion OS bugs or memcached bugs can contribute. Well.. it is most certainly not performing like an O(1) operation for me. Under low to normal load on our site memcached response times for get and set ops are about 0.001 seconds. Not bad. But if we triple the load we get outliers that take 100x (or in rare cases 1000x!) that long. I even had one instance where it took 2.2442 seconds for memcached to store a value. Obviously this is killing our site. Here's the output of Memcached-getStats during one of the slow periods: [pid] => 18079 [uptime] => 8903 [threads] => 4 [time] => 1332795759 [pointer_size] => 32 [rusage_user_seconds] => 26 [rusage_user_microseconds] => 503872 [rusage_system_seconds] => 125 [rusage_system_microseconds] => 477008 [curr_items] => 42099 [total_items] => 422500 [limit_maxbytes] => 943718400 [curr_connections] => 84 [total_connections] => 4946 [connection_structures] => 178 [bytes] => 7259957 [cmd_get] => 1679091 [cmd_set] => 351809 [get_hits] => 1662048 [get_misses] => 17043 [evictions] => 0 [bytes_read] => 109388476 [bytes_written] => 3187646458 [version] => 1.4.13 So things that I have ruled out so far are: Hitting the max connections limit (curr_connections of 84 is well below the default of max of 1024) Swapping - the machine has 900M out of 1024M of memory dedicated to memcached on a dedicated machine. It only appears to be using about 7MB of data as per the bytes stat. How would I diagnose the other hardware problems? prstat doesn't really show a whole lot going on in terms of CPU or memory usage. Not sure how to figure out the network problems but as this is a dedicated server on the same private network as the web box I don't think it's a connectivity issue (ping is less than a millisecond between the boxes). Is there something else I'm missing here? It's driving me nuts. Edit: Also forgot to mention that I've tried both persistent and non-persistent connections with minimal-to-no impact.

    Read the article

  • Routing and arp

    - by adolgarev
    If I have >ip ro 192.168.14.0/24 dev eth0 another host can obtain my mac address. But if I flush routing info: >ip ro flush table main arp resolution doesn't work. Broadcast packets "Who has 192.168.14.149" reach eth0 but OS (Linux) doesn't respond despite eth0 has address 192.168.14.149. What connection exists between routing and arp resolution?

    Read the article

< Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >