Search Results

Search found 5628 results on 226 pages for 'cpu hogging'.

Page 189/226 | < Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >

• Frequency of RAM

  - by Vignesh Palani

  I have a very old system hp compaq dx2080. It had 1gb of RAM. I recently bought a EVM DDR2 1 GB PC RAM which had a clock rate of 667Mhz. I have dual booting windows 7 and 8. When I installed it, windows 7 was still using the older 1gb. It showed as 2 gb available and 1gb usable in system properties. I searched around and found that I can change it to max in the msconfig. I did so. I set it 2048. Still, it was using only 1gb. When, I switched to 8, it was using the 2gb. Now, for my question: My system only supported 553Mhz and 667Mhz RAM. In the BIOS, I saw that the new RAM was showing as 800Mhz. Rechecked using speccy and cpu-z. It showed different values between the two. The RAM is labeled as 667Mhz over it. No mistake in that. But, am I missing something? Please help. And, can I continue using it? My point again. There are only two slots.

  Read the article

• Webcam security camera software that runs as a service

  - by hurfdurf

  I've been looking for Windows webcam software that will run as a Windows service without any user login. The goal is to use the webcam as a cheap security camera and log the results to secure networked storage (windows share, not FTP). The requirements are: Motion detection Video capture Runs as a service (should start recording immediately after reboot) Nice to have: Round-robin storage, e.g. 10Gb limit, oldest files overwritten/deleted when space gets low I've read the other webcam questions but still haven't stumbled across anything suitable. Evaluations thus far: Title MotionDetect Service Snapshots Video SpaceLimit License Yawcam Yes Yes Yes No No GPL WebCam ZoneTrigger Yes No Yes Yes No Commercial Dorgem Yes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Logitech Yes No Yes Yes No Paired with camera IspyConnect Yes No Yes Yes Yes Free SecureCam (SourcefoYes No Yes Yes No GPL AbelCam Yes No Yes Yes No Commercial Active WebCam Yes Yes(?) Yes Yes Volume Free Commercial WebCam Surveyor Yes No Yes Yes No Commercial WebCamsPy NA NA NA NA NA GPL Camera: Logitech Webcam Pro 9000 Windows 7 32-bit WebCamsPy failed to initialize so couldn't be tested So far, the contenders: Active Webcam comes the closest, and claims to run as a service, but i haven't been able to get it to record after a cold boot even though a service is running. Yawcam can be set up as a service but doesn't record video. IspyConnect has exactly the type of space limit I want and looks great, but doesn't run as a service (seems also to be a bit of a cpu hog) Any other suggestions? I'm locked into Windows so can't use linux Motion, which looks almost perfect. Any pointers to rich Windows webcam/motion detection libraries out there that could easily be turned into a command line program would also be appreciated.

  Read the article

• VMware Workstation "Power off" and "Suspend" buttons are disabled. What is going on?

  - by Ed Norris

  I've been using an XP image for a few months now with no problems. Recently the power off and resume buttons were disabled and I'm not sure what happened to cause that. In addition, the menu items to do those functions are grayed out (like VM | Power | Power Off) I'm using VMware Workstation 6.5.3 on a Windows 7 64-bit host. The image is Windows XP 32-bit. There is plenty of free space and memory on the host and the CPU is not pegged. I am able to power off the image through its Start menu, but that's a workaround not a fix. Any suggestions? TIA EDIT: Well after manually shutting down the image then closing and reopening the image file (which I've done before) in preparation for reinstalling the tools as suggested below, it looks fine. The power off and suspend buttons are enabled and work. So what do I do with this question now? "Close and restart a few times and it may work" doesn't seem useful...

  Read the article

• Hadoop streaming job on EC2 stays in "pending" state

  - by liamf

  Trying to experiment with Hadoop and Streaming using cloudera distribution CDH3 on Ubuntu. Have valid data in hdfs:// ready for processing. Wrote little streaming mapper in python. When I launch a mapper only job using: hadoop jar /usr/lib/hadoop/contrib/streaming/hadoop-streaming*.jar -file /usr/src/mystuff/mapper.py -mapper /usr/src/mystuff/mapper.py -input /incoming/STBFlow/* -output testOP hadoop duly decides it will use 66 mappers on the cluster to process the data. The testOP directory is created on HDFS. A job_conf.xml file is created. But the job tracker UI at port 50030 never shows the job moving out of "pending" state and nothing else happens. CPU usage stays at zero. (the job is created though) If I give it a single file (instead of the entire directory) as input, same result (except Hadoop decides it needs 2 mappers instead of 66). I also tried using the "dumbo" Python utility and launching jobs using that: same result: permanently pending. So I am missing something basic: could someone help me out with what I should look for? The cluster is on Amazon EC2. Firewall issues maybe: ports are enabled explicitly, case by case, in the cluster security group.

  Read the article

• Xubuntu stuck after login

  - by viraptor

  How can I debug an issue with Xubuntu 12.04 (fresh install) which just waits idle after a login for about 30 seconds? The login screen is delayed correctly. After login, I get my desktop background, but no panels or auto-starting apps. It doesn't seem to be an authentication/pam issue, because I can login without delay at the console while the graphical session is still stuck. There's no disk or cpu activity and no obvious respawning of any process when I look at htop. There's nothing obviously wrong in .xsession-errors. Most interesting errors: openConnection: connect: No such file or directory cannot connect to brltty at :0 WARNING: gnome-keyring:: couldn't connect to: /tmp/keyring-wFn4VR/pkcs11: No such file or directory ... (polkit-gnome-authentication-agent-1:2131): polkit-gnome-1-WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The nam e org.gnome.SessionManager was not provided by any .service files ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ... (xfce4-indicator-plugin:2176): libindicator-WARNING **: IndicatorObject class does not have an accessible description. ... (xfce4-indicator-plugin:2176): Indicator-Application-WARNING **: Unable to get application list: Operation was cancelled Bootchart seems to end before I login, so it's not that helpful. Where else can I look for information?

  Read the article

• Wake for Network Access Apache servr in OS X 10.8, followup

  - by Gary

  Sorry, I can't seem to post this response within the same thread. Thank you both (Zoredache and Gordon) for your answer. But the fix seems temporary. I entered the command you suggested, and it seemed to work: ...smith$ Registering Service ApacheNoDoz._http._tcp.local port 80 DATE: ---Fri 14 Sep 2012--- 12:04:15.813 ...STARTING... 12:04:16.566 Got a reply for service ApacheNoDoz._http._tcp.local.: Name now registered and active So, I checked for it on my G5: Browsing for _http._tcp Timestamp.....A/R Flags if Domain......Service Type...Instance Name (lots of Bonjour printers omitted)... 12:07:38.370..Add.....2..4 local.......... _http._tcp.........ApacheNoDoz 12:07:45.921..Rmv.....0..4 local..........._http._tcp.........ApacheNoDoz So, it was running at 12:07:38, at which time the host was asleep. But, shortly after, the activity seems to have been removed. I don't know why. Does this mean that I can never let the cpu sleep, or is there something else I have to set? Thanks, again.

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

• Php5-fpm Crash if much visitors

  - by chillah

  I decided to change my OP to Nginx from Litespeed because i read much about the low resource that Nginx would cost. Im running a Wordpress site with 500 users online My www.conf in "/etc/php5/fpm/pool.d" pm.max_children = 200 pm.start_servers = 20 pm.min_spare_servers = 20 pm.max_spare_servers = 60 ;pm.process_idle_timeout = 10s; ;pm.max_requests = 1000 Since i changed that config to higher requests and more children the Site needs longer till it shows me a White blank page. If i restart the php5-fpm prozess then, the site is running fine again. The CPU usage is at 5% if the php5-fpm is crashed and if its running its about 20 to 90%! Heres my Nginx.conf: user www-data; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 3048; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; I already tried changing the settings, tryed all variants but nothing worked. The Mashine: Dualcore 4gb ram

  Read the article

• Upgrading memory in a laptop

  - by ulidtko

  I'm a bit confused about all the memory types and various bus frequencies of modern consumer PCs. Requesting expert help on the subject. So far I'm confident that: I have an Asus X51L laptop with an unknown set of configuration options. The CPU in there supports PAE, so I still have a chance to extend the memory beyond 3GiB; and the upper limit of the system is 8GiB. (?) The laptop has two SODIMM slots, one of which is occupied by a 2GiB bank, and the other one is empty. dmidecode and lshw tools consistently state 533 Mhz frequency of the bank. The last one confuses me the most. I failed to find out characteristics of the northbridge in this laptop, and still can't figure out what DDR2 to seek for. Is it DDR2-1066? Or, rather, PC2-8500/PC2-8600? Wouldn't a DDR2-800 bank harm the system's performance? Which kind of modules should I look up in stores? Update: I have bought a 2 GiB DDR2-800 SODIMM, and it seams that the system can't handle 4 GiB of memory. When installed by itself in either slot, both new and old bank (which btw happens to be marked GDDR2-677) work just perfectly; i.e. any configuration resulting in 2 GiB works. When both banks are installed though (totalling in 4 GiB), the memcheck86 tool produces horrible artifacts and crashes, and system reboots; an Ubuntu system can be started and even logged into a Unity session, but the system reboots too in this case from even a minor RAM load. So it's pretty obvious to me now that this laptop doesn't support 4 GiB of RAM or more.

  Read the article

• Measuring performance indicators on a cluster

  - by Aditya Singh

  My architecture is based on Amazon. A ELB load balancer balances POST requests among m1.large instances. Every instance has a nginx server on port 80 which distributes the requests to 4 python-tornado servers on backend which handle the request. These tornado servers are taking about 5 - 10ms to respond to one request but this is the internal compute time of every request. I want to put this thing on test and i want to measure the response time from ELB to upstream and back and how does it vary when the QPS throughput is increased and plot a graph of Time vs. QPS vs. Latency and other factors like CPU and Memory. Is there a software to do that or should i log everything somewhere with latency checks and then analyze the whole log to get the stuff out. I would also need to write a self-monitor which keeps checking the whole response time. Is it possible to do it with a script from within the server. If so, will it be accurate ?

  Read the article

• How can I install iTunes in such a way that it can't put any "hooks" or helper programs on my computer?

  - by Joshua Carmody

  I'm buying a new iPad, which means I must once again install iTunes. I've not used iTunes in more than 6 months, since I bought a new computer. I don't like iTunes, but I can live with using it to buy/manage media and sync my Apple devices when the program is open. What I would like to do though, is find a way to install iTunes in such a way that it has absolutely no effect on my system when it is closed. iTunes normally installs several helper programs such as iTunesHelper.exe, and the Bonjour service. These programs run in the background when iTunes is closed. You can force-close them, or remove them from your setup files, but iTunes will often put them right back when you run it. I know these programs are mostly harmless, but they have at times caused issues such as iTunes spending system resources trying to catalog media files or drives connected to VPN, or other issues. At best they're just one more small background process eating up a small piece of my CPU time and RAM. How can I run iTunes without letting it get it's "hooks" into my system? One thought I had is that I could create a Windows user account just for iTunes, and deny it admin privileges. Then if I installed iTunes using that account maybe anything it installed wouldn't affect the "main" account on my PC? But I'm not sure if that would work.... Failing that, maybe some kind of virtualization software or sandbox I could install it in? I'm open to any suggestions. My system is an Intel-based PC running Windows 7 Professional 64-bit. Thanks!

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Why is my server performance degrading to the point of stopping, periodically?

  - by Pascal Aschwanden

  So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

  Read the article

• Value of Itanium or Sparc over x86_64 for Oracle Deployment

  - by Antitribu

  We are looking at a new environment to run our Oracle Database running on SUSE (potentially migrating to RedHat). Our database is approximately 100GB and performs adequately on our current hardware (x86_64) with approximately 6GB of ram allocated to it. We are growing quickly however and will require more performance shortly. Given the cost of Oracle licenses we would like to maximize the value from each license by choosing the most appropriate CPU to run the software on. The questions are: Are there substantial benefits to looking at Itanium or Sparc hardware, are there any drawbacks? Is there a point where one starts to scale out better? What are the long term support options for Itanium? Given the dominance of x86 would it be safer long term to stick with x86? On average what would be the performance benefit of implementing an Oracle database on Itanium or Sparc over x86_64? Is this an issue at all or will other factors (IO/RAM) cap out first? If anyone can point me towards some solid documentation on comparisons between the platforms that provides good case analysis of when to choose which I'm more than happy to accept that as an answer. Edit:- Added Sparc as an Option as it was previously not considered however with the recent Oracle Sun aquisition seems very relevant.

  Read the article

• How to kill ostensibly immortal process?

  - by DeeDee

  I had some huge file transfers operating on an NFS mount. The server on which the mount point resided was carelessly rebooted, and now the server from which these large transfers were initiated seems to be bogged down by them. If I run top, I see the following: The first thing I tried was to run kill with each the -1 -2 -9 and -15 flags, and each of the process ids shown above in turn. This allowed me to proceed, but didn't kill the processes. The next thing I attempted was to reboot the server, but neither reboot nor shutdown -r now worked. When I ran shutdown -r now the standard broadcast message was sent out, but the sever did not reboot. I confirmed this by looking at the server uptime, which was 25 days. So now I'm a little stuck. I'm running these commands as root. EDIT: Here's another interesting tidbit: In top, I don't see that any other processes are using more than a fraction of a percent of memory or more than 5% of CPU. EDIT 2: output of /var/log/messages

  Read the article

• Hung Java JVM failing to respond to kill -3

  - by Hans

  I have a Java VM that is hanging "randomly". I quote the randomly bit, because there is obviously a reason that the VM is hanging, but the hang does not occur periodically. We have the same software running in different customer environments and in those environments the JVM is not hanging. In the process of attempting to troubleshoot the hang the process exists with zero CPU utilization. I then attempt to execute kill -3 and the kill command hangs. No JVM Thread Dump is produced. I have spent time instrumenting the code to periodically log the thread stack traces hoping to catch the JVM in a state that would indicate where the issue lies, but so far this attempt has not born much fruit. Unfortunately I have not been able to reproduce this issue in my lab environment so I am limited by what can be done at the Customer site. The OS's in question are Red Hat Enterprise 5.4 and SUSE 10 running java version 1.6.0_05-b13 Has anyone had this problem? Any ideas on why kill -3 is failing to produce a Java Thread Dump? Thanks!

  Read the article

• Windows/IIS Hosting :: How much is too much?

  - by bsisupport

  I have 4 Windows 2003 servers running IIS 6. These servers host a bunch of unique web sites (in that they are all different in build/architecture/etc). The code behind these sites range from straight HTML, classic ASP, and 1.1/2.0/3.x flavors of .NET. Some (most) of the sites use a SQL backend, which is hosted on one or two different servers – not the IIS servers themselves. No virtualization on these servers and no load balancing for these particular sites. The problem I’m running into is coming up with some baseline metrics to determine, or basically come up with a “baseline score” to know when a web server has reached its hosting limit. Today, some basic information about each server is used: how much bandwidth does the server pump out, hard drive space availability, and basic (very basic) RAM & CPU utilization (what it looks like at peak traffic times.) I would be grateful if those of you that are 1000x smarter than I am could indulge me with your methods of managing IIS environments. Whether performance monitoring specifics, “score” determination as I’m trying to determine, or the obvious combination of both. Thanks in advance.

  Read the article

• SQL Server log backups "stalling"

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Strange IP address showing up with OS X ssh

  - by user50799

  I was futzing around with DTrace on Mac OS X and found the following script that prints out information about connections being established: $ cat script.d syscall::connect:entry { printf("execname: %s\n", execname); printf("pid: %d\n", pid); printf("sockfd: %d\n",arg0); socks = (struct sockaddr*)copyin(arg1, arg2); hport = (uint_t)socks->sa_data[0]; lport = (uint_t)socks->sa_data[1]; hport <<= 8; port = hport + lport; printf("Port number: %d\n", port); printf("IP address: %d.%d.%d.%d\n", socks->sa_data[2], socks->sa_data[3], socks->sa_data[4], socks->sa_data[5]); printf("======\n"); } I run it in one window: $ sudo dtrace -s ./script.d Then I ssh to another machine from another window. I get this output from my dtrace window: CPU ID FUNCTION:NAME 0 18696 connect:entry execname: ssh pid: 5446 sockfd: 3 Port number: 22 IP address: 192.168.0.207 ====== 0 18696 connect:entry execname: ssh pid: 5446 sockfd: 5 Port number: 12148 IP address: 109.112.47.108 ====== ^C The first IP address I can explain (192.168.0.207), that's the machine I'm connecting to. But what's with the 109.112.47.108 machine? It doesn't show up in tcpdump nor netstat -an Is there something with my dtrace code or my understanding of how the connect system call works?

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• kde dropping keyboard

  - by shabbychef

  I am having problems with KDE 'dropping' my keyboard. It happens periodically when using my gentoo box directly, but has become much worse when accessing via NX (from a Mac laptop). Some possibly irrelevant clues: it appears to happen more often when the system is under higher CPU load the mouse continues to work, but no windows will accept any kind of keyboard focus. kwin will not accept tabbing between windows. when working on the machine directly, I can ctrl-alt-F1 to get to a shell (obviously this does nothing over NX). so I think it is KDE and not xorg. am running kwin-4.3.5-r1, and KDE-4.3.5 generally. this problem definitely appeared after upgrading to kde-4.x, but I do not remember if it appeared in kde-4.2. sometimes the keyboard will reappear, but sometimes I have to kill my kde session. playing with accessibility options or window-focus-stealing options in system-settings under kde will often make the keyboard responsive again, only to drop it perhaps minutes later. I had read online this might be an evdev problem under X (again, I think this is KDE, not X, but will try anything). as a result, I have fiddled with my xorg.conf endlessly. I even deleted it entirely and let nvidia-xconfig have a stab at it, with no luck I am tearing my hair out over this. I have done emerge -e xorg-server and am right now doing emerge -e kwin, to rebuild all packages that might be relevant. no luck with the xorg-server rebuild. any help appreciated. thanks,

  Read the article

• Is there an application to log component temperatures to file?

  - by MrVimes

  I purchased a computer a month or two ago (core i7, 24gb ram, geforce gtx 590, windows 7 ultimate). Within the last week it began to bluescreen regularly. I tried lots of things (check hds, check memory, reinstall windows etc..) but it still bluescreened. At the time my temps were as follows... CPU - aprox 40/50c. GPU - arpox 60 idle, aprox 90 during heavy use. HDDs - aprox 55c after the PC had been on a while. I thought the 55c was ok, but I have since realized it was probably too high and may have been the direct cause of the bluescreening. I've installed a spare fan I had in the front of the PC blowing air in, (so there's airflow from front to back) Since then, obviously, all my temps are down. Especially the HDDs - three of them reach 30c and one has been up to 47c (it is some distance away from the airflow, in one of the 5.25inch drive bays) I haven't had the PC on for as long as it would normally take to bluescreen yet, but If it does I want to know what all the temps were right before the bluescreen. I have tried Everest but it only shows me realtime temps or gives me the ability to create one-off reports. I want something that can record all the temps to a file at 30 seconds intervals. If the computer bluescreens I can load it up again and check the last entry in the file. Side question: Am I right in thinking 55c was far too hot for a HDD? (It might have got higher than that before the bluescreens.. I don't know) Another side question: Is 47c too high? This is actually why I am asking the main question - I am concerned that this one drive that isn't getting the benefit of the extra fan may still cause the computer to bluescreen.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• System randomly freezes yet mouse still moves, SSD out of reallocatable sectors, should I replace it?

  - by user784446

  This problem has lasted for the past 48 hours. The first time it happened, a program I was running stopped responding, so I tried to end it from task manager. The processes at first were listed fine until hovered upon. Eventually, despite the mouse still being able to move, after a few persisting clicks the mouse finally stopped moving. The screen went blank shortly thereafter. The second time it occurred, items on the screen stopped responding - hovering over the taskbar or such wouldn't elicit a response. Sound would still play however. Eventually, the mouse became unresponsive and the system restarted itself. I suspect that it may be a problem of my SSD drive. After looking through some Google search results, I downloaded HDTunePro to determine if there's a problem with the drive. Results returned a problem of reallocated sector count. An error scan also revealed 48 bad sectors. Also, an attempt to backup the contents of the most important areas of the drive returned a few explorer "Error: cannot read source from disk" errors. Should I ditch the drive and use another drive or is there anything that can be done to repair the drive? SSD: OCZ Petrol 64gb CPU: AMD Athlon II X4 640 RAM: Generic 3GB DDR2 Motherboard: Gigabyte MA74GM-S2H OS: Windows 7 Ultimate x64 Thanks!

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

< Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >