Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 190/783 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

• Correct way of bringing network interface down in linux

  - by Karolis T.

  For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

  Read the article

• Adding a Printer to my Print Server Failing

  - by Rudi Kershaw

  So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

  Read the article

• How do I configure a secondary gateway in RHEL5?

  - by Brett Ryan

  Greetings, we have been experiencing a random timeout issue with VPN users connecting to one of our servers which is causing a problem. My network administrator has instructed me to configure a secondary gateway to include the VPN connection. My current connection resides as follows, 10.1.9.1 is the internal gateway to the internet, I'd like to add 10.1.1.20 as the VPN gateway. # Broadcom Corporation NetXtreme II BCM5708S Gigabit Ethernet DEVICE=eth0 BOOTPROTO=none BROADCAST=10.1.255.255 IPADDR=10.1.1.22 IPV6_AUTOCONF=yes NETMASK=255.255.0.0 NETWORK=10.1.0.0 ONBOOT=yes GATEWAY=10.1.9.1 TYPE=Ethernet USERCTL=no IPV6INIT=no PEERDNS=yes

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• finding the best network latency between two countries

  - by Yoav Aner

  I know there are many tools to test for bandwidth and latency, but they all rely on having at least one host from which you can run those tests. I wonder whether there's an online source or some other way to guestimate the latency or speed between two countries (in general). For example, would a customer in Japan get lower latency if the server is located in Singapore or Australia? Is a user in India likely to get higher download speed from a server in the UK or in the US? Are there any online resources or some clever ways to answer those questions with a reasonable degree of accuracy? [UPDATE]: Thanks for the great suggestions from Raffael Luthiger. I didn't know about those looking glass servers. The submarine cable maps were also really cool to discover (Thanks to Jesper Mortensen). Also seems really wise if I could ask those network professional in the area for their experience, but obviously I don't have access to those. At least some of them are on SF :) However, I'm still a little unsure how to combine those resources to give me some measurements. This is the information I have: Two countries (A,B). I do have IP addresses of customers in country A (I can obtain those from the web server log files for example). Presumably I can find some looking glass servers in country B and run a trace to those IPs. What's the best measurements to use? Are there any scripts that help automate at least some of this process?

  Read the article

• Optimizing wireless router speed and minimizing interference.

  - by Tchalvak

  I've been experiencing problems with my wireless connectivity lately, and want to make sure that it's not related to the abundance of other wireless routers here in my building. So, what I'm looking for is a method (probably via some application or another) to audit the wireless channels (and other factors that might be important that I don't even know of yet) that are floating through the aether around me. Ubuntu or other linux apps are preferred, but some kind of windows/mac solution is possible, since I do have other OSes around me that I could install & test on. Router: netgear WGT624 v3 Hearsay tells me that channels 1, 6, and 11 are "non-overlapping" (I expect they aren't used for non-wireless-router purposes or something, not sure how they couldn't overlap with other routers using other channels), so perhaps my best choices of channel are limited, so if channels aren't really a big concern, I'd be happy to get links to other optimizations that I should look into.

  Read the article

• Cannot access server shares over VPN

  - by DuncanDavies

  I've set up a single hosted server to use as a development environment for a web-based application. The web app is served up fine on port 80, however I'm struggling to get my VPN to behave how I'd expect so the developers don't have the access they require. The VPN connects fine and I can access the back-end database (SQL Server) which resides on the server with the client tools from the laptops. However they cannot access any shared folders. The server's local IP address is 10.x.x.x, and I've assigned a static IP address pool to RRAS (of 192.168.100.1 - 20). The clients pick up a valid IP Address (i.e. 192.168.100.9) when they connect. There is no name resolution setup, DNS or WINS. When connected via VPN the clients can ping the server (192.168.100.1) by IP Address, but cannot map a drive to a shared folder (net use * \\192.168.100.1\xxxxx) - I get 'System error 53 has occurred. The network path was not found.' I don't understand why I can ping by the ip, but not map by it. Some details: Server OS is Windows 2008 (Datacenter) VPN is SSTP using RRAS Clients are all Windows 7 I've tried temporarily disabling the firewalls So, why can we not access the file system when everything else (ping, RDP, SQL Server clients tools) works? Thanks for your help Duncan

  Read the article

• Simulating a low-bandwidth, high-latency network connection on Linux

  - by Justin L.

  I'd like to simulate a high-latency, low-bandwidth network connection on my Linux machine. Limiting bandwidth has been discussed before, e.g. here, but I can't find any posts which address limiting both bandwidth and latency. I can get either high latency or low bandwidth using tc. But I haven't been able to combine these into a single connection. In particular, the example rate control script here doesn't work for me: # tc qdisc add dev lo root handle 1:0 netem delay 100ms # tc qdisc add dev lo parent 1:1 handle 10: tbf rate 256kbit buffer 1600 limit 3000 RTNETLINK answers: Operation not supported How can I create a low-bandwidth, high-latency connection, using tc or any other readily-available tool?

  Read the article

• My DNS cannot resolve an web site address?

  - by ipkiss

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me please? Thank you.

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Internet connection very slow after Linksys configuration

  - by NLV

  Hello We have this network setup Server1 - DHCP server, Domain Controller, AD Lease line for Internet connection From lease line to Linksys router (we dont use wireless though) From linksys to Netgear (24 port Switch) and vonage (VoIP) Netgear to all our machines We configured Linsys with the static IP and DNS server addresses our ISP gave and we have routed it correctly. All our work machines are configured with Get IP automatically DNS server addresses our ISP gave The problem is that none of the sites are getting opened promptly. It is taking around 5 minutes to load google.com. But we are able to ping all the sites. What could be the problem?

  Read the article

• Vista laptop 1 connects to network but Vista laptop 2 doesn't

  - by Jaips

  (Sorry if this is a dulipcate. I did a hunt but couldn't find matching question) We recently got a new router for our network (thomson TG585v8). It was already pre-configured by the ISP and was easy to setup. Both Vista laptops in this home network connected without trouble as well a iPod touch, all via wifi. In the last two days one of the laptops has been unable to connect cleanly to the network (connects as unidentified network). The other laptop, and iPod have not had any issues. I can't think of anything that has changed to make this happen now. I have rebooted the laptop and the router. I have updated the laptop wireless driver I have checked the laptop is set to automatically get IP I have logged into the router which correctly identifies all three wireless devices. The problem laptop connects via LAN without issue. Some things that may or may not matter: The problem laptop also sometimes uses a 3G dongle Both laptops use Windows Live Mesh to sync folders Laptop is usually set to go to sleep NB: it seems this is an intermittent issue, after an hour (since i noticed it) it seems to have fixed itself. Would love ideas though to solve this problem for good.

  Read the article

• Is there a way to turn off the sound that plays when my computer reconnects to the wireless network?

  - by Dan Tao

  I know this seems silly. Obviously I could mute my computer, or turn the speakers off. But it seems like surely there should be a way that I can keep all of my normal computer sounds without having to hear this one sound (no, it doesn't really bother me; mostly my wife just wants me to turn it off because she finds it annoying). I tried right-clicking on the volume icon in the notification area and went through all of the sounds in the list, thinking I could find the one offending noise and just turn it off. But none of them seem to correspond to the sound that plays when my wireless adapter randomly disconnects and reconnects to the wireless network.

  Read the article

• Barebones network appliance, 4+ GbE NICs, Intel chipset

  - by gravyface

  Looking for a stepped-up ALIX or Soekris embedded network appliance to load pfSense and/or handle other FOSS-based network roles. Main criteria is a GbE NICs (will be used for core routing/firewalling with managed GbE switches), DDR3 RAM capable, and multi-core/Intel Atom processor, in a 1U rack-mountable case or smaller. Axiomtek has the ideal product but I don't think they have retail channels.

  Read the article

• Setting up router: I can get online via Ethernet, and I can connect to router wirelessly, but can't

  - by Gabe

  I'm setting up a new D-Link N300 router, and trying to connect a MacBook Pro and a MacBook, both running OS X 10.6. As the question says, either computer can connect to the internet when connected to the router via Ethernet. And either one can get on the router's wireless network. But when connected wirelessly (without the Ethernet cable plugged in), neither one can get online. I can't figure out why that would be. Any help appreciated.

  Read the article

• Why can't I access my own web server from my local network?

  - by frenetic

  I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

  Read the article

• Why can't I access my own web server from my local network?

  - by frenetic

  I have a web server in my home network and I'm using ZoneEdit for dynamic DNS. It's accessible perfectly to everyone outside of my local network, but since I switched to a Gateway 2Wire DSL modem/router I'm unable to use the domain to access the server from my network. I can access it via a local IP or by putting it in my Windows hosts file but this is annoying to do on every computer and for every subdomain. Any idea how I can fix this? Thanks!

  Read the article

• Cisco AnyConnect with Automatic Proxy Configuration

  - by MadDogMatthew

  My Cisco AnyConnect 2.3 client isn't able to connect to my VPN through a corporate firewall. The client works fine on other networks. There is a automatic proxy configuration on the corporate network that uses a PAC file. Do I need to configure the AnyConnect client to use the PAC file?

  Read the article

• Network topology question

  - by Asbie

  We currently have three networks, X.X.163.1, X.X.93.1 and 192.168.1.1. Today's setup is like this: http://i.imgur.com/tkKWy.jpg We now have PPT VPN from internet to the X.X.163.1-network, but really need to access the files from the File Server through VPN. I am also aware that this setup is not optimal. So please, any advices on how to redesign our network? Rack servers are mostly web and db servers, with only public IP addresses.

  Read the article

• network topology including many services

  - by mete

  I know this is yet another question on how to setup network but I hope you are not bored of such questions yet. The site is also an office, so it includes windows dc, windows ad, exchange, sql, file sharing, development app servers and other pcs. In addition to office (internal) things, there are both test and prod environments consisting of a web server-app server-sql stack. There is also ftp service open to public. I consider: dmz1 - web server - exchange edge - ftp dmz2 - app server - sql for app server internal - dc and ad - exchange hub and transport - internal file sharing - sql for internal use - app servers for internal use - pcs public - dmz1, only web, ftp and smtp public - dmz2 not possible public - internal not possible dmz1 - dmz2 is possible from web servers to app servers by using http or ajp dmz1 - internal is only possible for exchange, otherwise not possible dmz2 - internal not possible Does this sound ok ? Any other recommendations ? It will be configured using either MS ISA or Jupiter SSG. Thank you.

  Read the article

• Does an unmanaged 4/8-port GBit Ethernet switch with a GBIC port exist?

  - by Aaron Digulla

  I'm looking for a simple unmanaged switch with 4-8 GBit Ethernet ports and a fiber port (either as a GBIC slot or pre-installed with a 1000BASE-SX port). Does something like that exist? [EDIT] I want to connect to places in my home without drilling large holes though the floors. Therefore, I'm looking for a cheap way to connect two GBit switches via fiber. I tried with a media converter (GBit <- multimode fiber) but that costs about 50% throughput. So I was hoping that there is a cheap, small GBit switch which has a GBIC slot). All I found so far are very expensive managed switches with 12 or 24 ports for industry use.

  Read the article

• Torrent upload ratio not updated on Synology DS212+

  - by user179271

  I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

  Read the article

• triple duplicate acknowledgement in TCP congestion control

  - by Salvador Dali

  If this doesn't belong here, please tell me where is an appropriate place for such question. I am trying to understand ideas behind tcp congestion control mechanisms, and I am failing to understand why we need triple duplicate acknowledgement to trigger window change. In my opinion, double duplicate acknowledgement will be enough to get that the previous package is lost. So why we need the third ack?

  Read the article

• Blocking ICMP outgoing requests only in eth1

  - by Raj

  I am creating a NAT with iptables: Computer A: eth0 (dhcp) + eth1 (static ip 192.168.0.1 - gateway) Computer B: eth1 (static ip 192.168.0.2, using Computer A as gateway) I know how to block ICMP outgoing requests (-A OUTPUT -p icmp --icmp-type echo-request -j DROP), but that would block ICMP requests from Computer A, but not from Computer B (in fact, only for Computer A - Computer B can keep doing those). I tried with the same command, but adding -o eth1, but that does not block at all. Any idea?

  Read the article

• With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

  - by larsks

  I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

  Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >