Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 190/391 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

  • MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

    - by user88114
    This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

    Read the article

  • Force failover a Cisco ASA

    - by user974896
    I have two ASA in a lan state primary\secondary configuration. None of them have "failover active" or "no failover active" in their configuration. Would it be proper to failover in a manner such as: Log into console of primary unit and issue "failover lan state secondary", log into the console of the original secondary unit and issue "failover lan state primary". To fail back simply reverse the process or Log into the console of the primary unit and issue "no failover active", log into the console of the original secondary unit and issue "failover active". To fail back issue "failover active" on the original primary (now secondary) unit, and "no failover active" on the now primary unit. I do not like the second method because it adds configuration directives that were not in place before. Will the first method work?

    Read the article

  • How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface?

    - by JJarava
    This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

    Read the article

  • Windows 7 Administrator HomeUsers Account

    - by Charles Carrington
    I'm trying to login to my Windows 7 PC from another PC so that I can transfer files to the Windows 7 PC. I've just installed Visual Studio 2008 on my new PC, and I wan't to transfer all of my work from my old machine to my new one. When I first set up a user on the Windows 7 PC after a reformat, the account created had a Group field that read "HomeUsers; Administrators" when viewing it from the User Accounts screen. You get to this screen by typing "netplwiz" in the search field of the Start Menu. I changed the Group of this account to Administrators before I realized that it was assigned to two Groups -- "HomeUsers; Administrators" as I mentioned above. I was trying to make sure that it was an Administrator account so I didn't have to type in a password everytime I wanted to install software. I can use this computer normally without being asked for an administrator password all the time when I want to install new software, but I can't log in to this PC from another PC because I don't have an account that has a Group of "HomeUsers". I should have left the account alone; everything would've been fine. But there doesn't seem to be a way to assign it to two groups after the initial assignment that take place automatically when you are setting up your computer for the first time. If you assign "HomeUsers" to the account, the Group field on the User Accounts screen will just read "HomeUsers". If you assign "Administrators" to the account, the Group field on the User Accounts screen will just read "Administrators". There's no way to make it read "HomeUsers; Administrators" again. If you don't have at least one account that is a "HomeUsers" account, you cannot log in to the PC from another PC on the network. If you don't have an account that is an "Administrators" account, you cannot install software on your machine without being asked for an Administrator password all the time, which is very annoying. I want an account on my Windows 7 PC that I can use to install software without being asked for a password AND that I can log into from another PC on the network to transfer files. If I could make the Group field read "HomeUsers; Administrators" of my primary account on the Windows 7 PC when I go to the User Accounts screen by typing "netplwiz" in the search field of the Start Menu, my primary account would do what I want it to do. Does anybody know how to make an account in Windows 7 a "HomeUsers" account AND an "Administrators" account? As I said before, Windows 7 does this for you automatically when you first set up your computer. But if you change it inadvertently, there is no way to change it back. At least I don't know how to do it. If anybody has any ideas on how to fix this, I would greatly appreciate it. Thanks, Charles Carrington

    Read the article

  • VM can't connect to outside in bridged mode

    - by Kamal
    Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

    Read the article

  • Do all the network cards use the same frequency to send signals to wire?

    - by smwikipedia
    I am comparing my cable TV wire to my network wire. In a TV cable wire, different frequencies are used by different TV channels. And since a certain channel use a fixed frequency, I think the only left way to represent different signal is with the carrier wave's amplitude. But what about the network wire? For all the network cards with the same type, do they also use different frequencies to send signals just like TV cable? I vaguely remember that they use frequency adjustment to represent signals. So the frequency should not be a fixed one. So how did all the network cards that sharing the same medium differentiate their own signal from others?

    Read the article

  • Beam display from any computer to shared display

    - by rcourtna
    There are probably a lot of ways to skin this cat. Looking for the cleanest. In our office, we have a large display in a common area. We want to allow any computer in our office (mac, linux, windows) to output its video on the large display. Since some of the computers in the office are stationary, and it's not practical to run video cables everywhere, it would be preferable to make this all happen through the network. It is also possible for us to connect a dedicated (& networked) PC to the large display. How can I do this?

    Read the article

  • Network access lags for Win7 when server network utilization is high

    - by Jeff Miles
    We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

    Read the article

  • Default gateway is in different subnet. How to configure in RHEL6.2

    - by Dmytro Leonenko
    I have two subnets routed to my server from ISP. I have only one gateway ip. The gateway is on the same VLAN as my IP address. For example netowrk 1 is 1.0.0.0/24 and network 2 is 2.0.0.0/24. Both are routed to eth0 by my ISP. Gateway is 1.0.0.1. My host ip is 2.0.0.1/24 (eth0) So I can configure default gateway manually with ip route add default dev eth0 ip route add default via 1.0.0.1 and then internet connection works properly. How do I configure it in /etc/sysconfig/network-scripts/ifcfg-eth0 ? I tried to set GATEWAY=1.0.0.1 but it doesn't work. Tried to set GATEWAY and GATEWAYDEV in /etc/sysconfig/network and it does only what first command from listing above do.

    Read the article

  • Adding a Printer to my Print Server Failing

    - by Rudi Kershaw
    So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

    Read the article

  • how to run an AFS file server on a specific ethernet card (in Debian)

    - by listboss
    I have a linux box running Debian server with minimal number of packages (so no GUI for network management). The box has two ethernet cards, one of which (eth0) is connected to a Mac OSX computer using a cross-cable. I can bring up eth0 and assign a static ip (10.10.11.16) to it. This way I can ssh to the box through the cross-cable. This is what I run on Linux box: ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up I also installed/started a file server (AFS) on Debian. So far, the file server can only be accessed through eth1 which is exposed to my home LAN and www. My goal is to set up the file server so that it's only visible through eth0. Is this possible? and if yes, how can I do it?

    Read the article

  • pfsense CARP - wan failure on firewall

    - by eldblz
    I have recently configured 2 firewall (on 2 DELL PowerEdge R210II with ESXI 5.1) with pfsense. We have several LANs and 2 WANs. Everything is running fine but i have a strange behavior: i can access internet from alla LANs but not from the firewall (itself). For example the firewall cannot retrive package information or if i setup a gatway monitor ip (like google 8.8.8.8 ) this fails. These are the screenshots of firewall configuration: http://imgur.com/a/LNuMz#0 ATM i kept firewall rules to minimum to avoid problem or conflicts. Any ideas how to solve the problem? Thank you in advance.

    Read the article

  • Translating debian network configuration to gentoo

    - by thpetrus
    I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

    Read the article

  • PTR Record for host in VLSM subnet

    - by paradroid
    I understand that this is the way a PTR record would be made on a Class A subnet (10.100.250.100 255.0.0.0) dnscmd /RecordAdd 10.in-addr.arpa. 100.250.100 PTR host.domain.tld To clarify the syntax, this is what it should be for a Class C subnet (192.168.1.100 255.255.255.0) dnscmd /RecordAdd 1.168.192.in-addr.arpa. 100 PTR host.domain.tld Is that right? Now how do I do this for a host with the IP address 172.31.111.210 on a 172.31.111.192/26 network? I'm not sure how to do this with a classless subnet mask.

    Read the article

  • How can I restrict SSH access when the source IP is dynamic

    - by Supratik
    Hi I want to protect SSH access to our live web server from all IP's except our office static IP. There are some employees who connects to this live server from their dynamic IP's. So, it is not always possible for me to change in the iptables rule in live server whenever the dynamic IP of the employee changes. I tried to put them in office VPN and allowed only SSH access from office IP but the office connection is slow in compared to our employee's private internet connection, moreover it adds an extra overhead to our office network. Is there any way I can solve this problem ?

    Read the article

  • Generate a limited amount of random network traffic between 2 hosts

    - by Andrew S
    I'm trying to find a utility that will allow me to generate a constant flow of random network traffic at a specified rate between 2 hosts. The utility needs to run on Windows and OSX. I've tried iperf but it seems to be more oriented toward short-term testing/statistics and it really taxes the CPU even at slower rates. I want something that will generate traffic for a few weeks at say 10Mbps while I use other tools to monitor the impact of that level of traffic on the network.

    Read the article

  • Facebook doesn't work on computer, but work on mobile device, both use the same router

    - by sasa
    I have a very strange problem and I'm thinking that can be problem with dns or something similar, but not sure and don't know how to solve. My computer is connected to router and every site works fine except facebook (Chrome and Firefox). Chrome shows "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." But, on mobile device witch is connected to the same router facebook works fine (Fb application and Delphin browser). Pinging facebook works fine. Clearing cookies and cache didn't help. Also, I performed antivirus and antimalware scan and there is nothing. What can be a problem? Update: I'm also connect notebook on that wifi router, and on it works fine. nslookup facebook.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: facebook.com Addresses: 2a03:2880:2110:3f01:face:b00c:: 2a03:2880:10:1f02:face:b00c:0:25 2a03:2880:10:8f01:face:b00c:0:25 69.171.224.37 69.171.229.11 69.171.242.11 66.220.149.11 66.220.158.11

    Read the article

  • Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

    - by Linux Guy
    I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

    Read the article

  • Why does 1GBit card have output limited to 80 MiB ?

    - by Gallus
    I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

    Read the article

  • Network latency and speed of light

    - by James
    This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

    Read the article

  • Configure TCP/IP to use DHCP and a Static IP Address at the Same Time

    - by Tiago
    My computer is configured to obtain a IP address automatically using DHCP. It only has one network adapter. How to configure an additional static IP address? I found a tutorial for Windows XP, but the procedure didn't work for Windows 7. Is it possible to configure two IP addresses on Windows 7, one being static e another being dynamic? How? The dynamic address I got now is 10.17.11.162. The static IP is 10.17.30.19. The network mask is the same: 255.255.224.0. Both work independently, but I don't know how to use both at the same time.

    Read the article

  • In TCP/IP terms, how does a download speed limiter in an office work?

    - by TessellatingHeckler
    Assume an office of people, they want to limit HTTP downloads to a max of 40% bandwidth of their internet connection speed so that it doesn't block other traffic. We say "it's not supported in your firewall", and they say the inevitable line "we used to be able to do it with our Netgear/DLink/DrayTek". Thinking about it, a download is like this: HTTP GET request Server sends file data as TCP packets Client acknowledges receipt of TCP packets Repeat until download finished. The speed is determined by how fast the server sends data to you, and how fast you acknowledge it. So, to limit download speed, you have two choices: 1) Instruct the server to send data to you more slowly - and I don't think there's any protocol feature to request that in TCP or HTTP. 2) Acknowledge packets more slowly by limiting your upload speed, and also ruin your upload speed. How do devices do this limiting? Is there a standard way?

    Read the article

  • Corosync :: Restarting some resources after Lan connectivity issue

    - by moebius_eye
    I am currently looking into corosync to build a two-node cluster. So, I've got it working fine, and it does what I want to do, which is: Lost connectivity between the two nodes gives the first node '10node' both Failover Wan IPs. (aka resources WanCluster100 and WanCluster101 ) '11node' does nothing. He "thinks" he still has his Failover Wan IP. (aka WanCluster101) But it doesn't do this: '11node' should restart the WanCluster101 resource when the connectivity with the other node is back. This is to prevent a condition where node10 simply dies (and thus does not get 11node's Failover Wan IP), resulting in a situation where none of the nodes have 10node's failover IP because 10node is down 11node has "given back" his failover Wan IP. Here's the current configuration I'm working on. node 10sch \ attributes standby="off" node 11sch \ attributes standby="off" primitive LanCluster100 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.100" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive LanCluster101 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.101" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive Ping100 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive Ping101 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive WanCluster100 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.100" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive WanCluster101 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.101" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive Website0 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf" options="-DSSL" \ operations $id="Website-one" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" primitive Website1 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf.1" options="-DSSL" \ operations $id="Website-two" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" group All100 WanCluster100 LanCluster100 group All101 WanCluster101 LanCluster101 location AlwaysPing100WithNode10 Ping100 \ rule $id="AlWaysPing100WithNode10-rule" inf: #uname eq 10sch location AlwaysPing101WithNode11 Ping101 \ rule $id="AlWaysPing101WithNode11-rule" inf: #uname eq 11sch location NeverLan100WithNode11 LanCluster100 \ rule $id="RAND1083308" -inf: #uname eq 11sch location NeverPing100WithNode11 Ping100 \ rule $id="NeverPing100WithNode11-rule" -inf: #uname eq 11sch location NeverPing101WithNode10 Ping101 \ rule $id="NeverPing101WithNode10-rule" -inf: #uname eq 10sch location Website0NeedsConnectivity Website0 \ rule $id="Website0NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 location Website1NeedsConnectivity Website1 \ rule $id="Website1NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 colocation Never -inf: LanCluster101 LanCluster100 colocation Never2 -inf: WanCluster100 LanCluster101 colocation NeverBothWebsitesTogether -inf: Website0 Website1 property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1408954702" \ maintenance-mode="false" rsc_defaults $id="rsc-options" \ resource-stickiness="100" \ migration-threshold="3" I also have a less important question concerning this line: colocation NeverBothLans -inf: LanCluster101 LanCluster100 How do I tell it that this collocation only applies to '11node'.

    Read the article

  • Disable dhcp client over one interface

    - by Lopoc
    Hi to all I'm encountering a problem on a sever with two ethernet interfaces(etho and eth1), it runs linux-ubuntu-server. I need eth1 not make any dhcp request, becouse I need it to be only a listening interface, obviusly I need eth0 running normally. So how can i disable any dhcpclient ation over eth1? thank in advance.

    Read the article

  • Servers behind load balancer

    - by Tom
    We have a CISCO hardware load balancer with two web servers behind it. We'd like to force some URLs to only be served by one of the machines. Firstly, is the job of the load balancer? or would a better approach be create a subdomain such as http://assets.example.com which would be automatically be routed to one of the servers?

    Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >