Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 186/391 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

• Monitoring bandwidth/latency/jitter between 2 sites?

  - by TheCleaner

  I have 2 sites connected via an MPLS network and I'd like to do the following: setup a host on each end that can "talk" back and forth between each other and somehow report/log what kind of throughput, jitter, latency, etc. they are experiencing between each other in 5 minute intervals. Something similar to Qcheck but that can be automated. Bottom line is I'm trying to determine if the WAN network is "stable" throughout the day or if something is wrong. We have video conferences between these sites and even at 1024kbps calls we are experiencing delays and jitter. I'm hoping to exonerate the network with some testing.

  Read the article

• With CentOS 6 and LXC, "ifconfig" is unable to see network interface (but busybox "ifconfig" works fine)

  - by larsks

  I've just started working with LXC under CentOS 6 (via the libvirt adapter). If I create an LXC container, I'm unable to see any network interfaces when using the native system tools: # ifconfig -a # The behavior is very odd; specifying an interface by names yields neither the expected output nor an error message. This is true even for clearly invalid interface names, like this: # ifconfig foo # The ip command exhibits the same behavior. On the other hand, if I use "ifconfig" provided by busybox, everything works as expected: # busybox ifconfig -a eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:268 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17814 (17.3 KiB) TX bytes:552 (552.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So...what does busybox know that the native tools don't? The libvirt config for this environment is pretty standard; the network definition looks like this: <interface type='network'> <mac address='52:54:00:e0:12:c8'/> <source network='default'/> <target dev='veth0'/> </interface> The full configuration is here if you think it might help. I'm running: lxc-0.7.2-2.el6.x86_64 kernel-2.6.32-71.29.1.el6.x86_64 EDIT Weirder and weirder...it's a display issue, not a functionality issue. I can see the output of ifconfig if I pipe it into anything, so for example: # ifconfig eth0 | cat eth0 Link encap:Ethernet HWaddr 52:54:00:E0:12:C8 inet addr:192.168.10.10 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fee0:12c8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:573 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37914 (37.0 KiB) TX bytes:552 (552.0 b) And in fact even when not piping the output, strace shows that ifconfig is in fact writing the output to file descriptor 1 (aka stdout), so it's not clear why no output is actually showing up. This could be either an LXC or a virsh issue, I guess.

  Read the article

• How to configure 2 LAN Cards

  - by PatDiazJr

  How do we configure two (2) LAN cards on one computer. One LAN card is connected to the internet via the DSL through a router, configured as DHCP. The other LAN card is to be connected via our office's IP/VPN (for email and other office online processes). I know it could be done, but I do not know how. By the way, the operating system is Windows XP.

  Read the article

• Why is my connection slow?

  - by Jay R.

  I have a Dell Precision T5400 with a Broadcom 1Gb onboard NIC. For some strange reason, when I access machines on our local network, the best I can get is around 125KB/s download speed. My laptop that has a 10/100Mb NIC onboard usually gets around 300KB/s or better from the same network resource. Both machines are plugged into the same 1Gb switch which connects to our local network wall jack at 100Mb half duplex. There is also a printer plugged into the same switch at 100Mb full. The resource I'm using for the test is a 30MB zip file copied from a jetty webserver that is running as part of a cruisecontrol installation. The cruisecontrol installation is running WindowsXP with full real-time antivirus and Altiris patch management and inventory running. That stuff on its own is eating some of the download speed. I've seen the laptop reach into the multiple MB/s download speed before, but the desktop never seems to get past 125KB/s to 130KB/s. In WindowsXP, before I upgraded the driver in the desktop, it was that slow. In Fedora, it is still slow even though it appears to be using the same driver version as the upgraded Windows driver. The upgraded Windows driver is faster, but still not nearly as fast as the laptop. What gives? Any insight to improve the situation would be appreciated. Could it be that the BroadCom board just isn't that good, or the driver in linux is just not as good as the Windows one?

  Read the article

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• DNS and IPs - Does DNS send the IP back to the client?

  - by Josh

  I ran across a site that talked about routing all cients requesting by IP to a "dead end." The clients accessing the site via ip it claimed were typically automated exploit tools and bots. Legitimate users type in the web address by it's domain question. With this context in mind, I don't really understand how DNS really works. I thought it worked by sending an IP back to a client for the requested DNS (like a phone book.) The client then uses the IP to access the site. The information above seems to indicate I misunderstand this. Can someone clarify this? (http://technet.microsoft.com/en-us/magazine/2005.01.hackerbasher.aspx)

  Read the article

• How do I wire a crossover cable to connect two devices together?

  - by Axxmasterr

  I need to make a ethernet crossover cable to connect two devices together. Anyone know the process to make one from scratch?

  Read the article

• How to selectively route network traffic through VPN on Mac OS X Leopard?

  - by newtonapple

  I don't want to send all my network traffic down to VPN when I'm connected to my company's network (via VPN) from home. For example, when I'm working from home, I would like to be able to backup my all files to the Time Capsule at home and still be able to access the company's internal network. I'm using Leopard's built-in VPN client. I've tried unchecking "Send all traffic over VPN connection." If I do that I will lose access to my company's internal websites be it via curl or the web browser (though internal IPs are still reachable). It'd be ideal if I can selectively choose a set of IPs or domains to be routed through VPN and keep the rest on my own network. Is this achievable with Leopard's built-in VPN client? If you have any software recommendations, I'd like to hear them as well.

  Read the article

• Accessing local resources over wifi with a BES-connected Blackberry

  - by bshacklett

  I'm trying to get to a local web site on my LAN at 192.168.1.10 with my Blackberry, but I'm getting a message saying the server did not respond. I know that some, if not all, internet traffic on a BES-connected blackberry goes through the BES. This is clear because I can access internal resources on my employers network via the mobile network. Is there any way for me to specify that the device should attempt to route directly over wifi before it tries to connect via the BES server at work?

  Read the article

• Ninety-Fifth Percentile Calculation for Bandwidth

  - by Kyle Brandt

  I am trying to calculate the bandwidth of my current internet connection. I am pulling the current input and output transfer rate via snmp. If the argument to the following function is a sorted ascending list of the the some of each input and output sample, is this the right way to calculate 95th percentile? sub ninetyFifth { #Expects Sorted Data my $ninetyFifthLine = (@_ * .95) - 1; return $_[$ninetyFifthLine]; }

  Read the article

• Netcat file transfer problem

  - by thepurplepixel

  I have two custom scripts I just wrote to facilitate transferring files between my VPS and my home server. They are both written in bash (short & sweet): To send: #!/bin/bash SENDFILE=$1 PORT=$2 HOST='<my house>' HOSTIP=`host $HOST | grep "has address" | cut --delimiter=" " -f 4` echo Transferring file \"$SENDFILE\" to $HOST \($HOSTIP\). tar -c "$SENDFILE" | pv -c -N tar -i 0.5 | lzma -z -c -6 | pv -c -N lzma -i 0.5 | nc -q 1 $HOSTIP $PORT echo Done. To receive: #!/bin/bash SERVER='<myserver>' SERVERIP=`host $SERVER | grep "has address" | cut --delimiter=" " -f 4` PORT=$1 echo Receiving file from $SERVER \($SERVERIP\) on port $PORT. nc -l $PORT | pv -c -N netcat -i 0.5 | lzma -d -c | pv -c -N lzma -i 0.5 | tar -xf - echo Done. The problem is that, for a very quick second, I see something flash along the lines of "Connection Refused" (before pv overwrites it), and no file is ever transferred. The port is forwarded through my router, and nmap confirms it: ~$ sudo nmap -sU -PN -p55515 -v <my house> Starting Nmap 5.00 ( http://nmap.org ) at 2010-04-21 18:10 EDT NSE: Loaded 0 scripts for scanning. Initiating Parallel DNS resolution of 1 host. at 18:10 Completed Parallel DNS resolution of 1 host. at 18:10, 0.00s elapsed Initiating UDP Scan at 18:10 Scanning 74.13.25.94 [1 port] Completed UDP Scan at 18:10, 2.02s elapsed (1 total ports) Host 74.13.25.94 is up. Interesting ports on 74.13.25.94: PORT STATE SERVICE 55515/udp open|filtered unknown Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 2.08 seconds Raw packets sent: 2 (56B) | Rcvd: 5 (260B) Also, running netcat normally doesn't work either: squircle@summit:~$ netcat <my house> 55515 <my house> [<my IP>] 55515 (?) : Connection refused Both boxes are Ubuntu Karmic (9.10). The receiver has no firewall, and outbound traffic on that port is allowed on the sender. I have no idea what to troubleshoot next. Any ideas? P.S.: Feel free to move this to SO/SF if you feel it would fit better there.

  Read the article

• Barebones network appliance, 4+ GbE NICs, Intel chipset

  - by gravyface

  Looking for a stepped-up ALIX or Soekris embedded network appliance to load pfSense and/or handle other FOSS-based network roles. Main criteria is a GbE NICs (will be used for core routing/firewalling with managed GbE switches), DDR3 RAM capable, and multi-core/Intel Atom processor, in a 1U rack-mountable case or smaller. Axiomtek has the ideal product but I don't think they have retail channels.

  Read the article

• Windows Server 2008 Migration - Did I miss something?

  - by DevNULL

  I'm running in to a few complications in my migration process. My main role has been a Linux / Sun administrator for 15 yrs so Windows server 2008 environment is a bit new to me, but understandable. Here's our situation and reason for migrating... We have a group of developers that develop VERY low-level software in Visual C with some inline assembler. All the workstations were separate from each other which cased consistency problems with development libraries, versions, etc... Our goal was to throw them all on to a Windows domain were we can control workstation installations, hot fixes (which can cause enormous problems), software versions, etc... All Development Workstations are running Windows XP x32 (sp3) and x64 (sp2) I running in to user permission problems and I was wondering maybe I missed one, tWO or a handful of things during my deployment. Here is what I have currently done: Installed and Activated Windows Server 2008 Added Roles for DNS and Active Directory Configured DNS with WINS for netbios name usage Added developers to AD and mapped their shared folders to their profile Added roles for IIS7 and configured the developers SVN Installed MySQL Enterprise Edition for development usage Not having a firm understanding of Group Policy I haven't delved deeply in to that realm yet. Problems I'm encountering: 1. When I configure any XP workstations to logon our domain, once a user uses their new AD login, everything goes well, except they have very restrictive permissions. (Eg: If a user opens any existing file, they don't have write access, except in their documents folder.) Since these guys are working on low system level events, they need to r/w all files. All I'm looking to restrict in software installations. Am I correct to assume that I can use WSUS to maintain the domains hot fixes and updates pushed to the workstations? I need to map a centralized shared development drive upon the users login. This is open to EVERYONE. Right now I have the users folders mapped upon login through their AD profile. But how do I map a share if I've already defined one within their profile in AD? Any responses would be very grateful. Do I have to configure and define a group policy for the domain users? Can I use Volume Mirroring to mirror / sync two drives on two separate servers or should I just script a rsync or MS Synctool? The drives simply store nightly system images.

  Read the article

• udp through nat

  - by youllknow

  Hi everyone! I've two private networks (each of them behind a typical dsl router). The routers are connected to the WWW. The extern interface of each router have one dynamic IP address. I want to stream data via UDP directly between one client in private network A and one client in private network B. I've already tried a lot of things (see: http://en.wikipedia.org/wiki/UDP_hole_punching, or STUN). But it wasn't possible for me to transfer data between the two clients. It's possible to use a server (located in the WWW, with static IP) to transfer the extern IPs (and extern ports) from the routers between the clients. So imagine client A knows client B's external IP and client B's external port assigned by his router. I simply tried sending UDP packet to the receivers external IP/port combination, but without any result. So does anyone know what do to communicate via UDP throw the two NAT routers? It must be possible??? Or does Skype, for example, not directly communicate between the clients when the call eachother (voice over ip). I am sorry for my bad English! If something is confusing don't mind asking me!!! Thanks for your help in advance. ::::EDIT:::: I can't get pwnat or chownat working. I tried it with my own dsl-gateway - didn't work. Then I set up a complete virtual environment using VMWare. C1 (Client 1, WinXP Prof SP3): 172.16.16.100/24, GW 172.16.16.1 C2 (Client 2, WinXP Prof SP3): 10.0.0.100/24, GW 10.0.0.1 C3 (Client 3, WinXP Prof SP3): 3.0.0.2/24, GW 3.0.0.1 S1 (Ubuntu 10.04 x64 Server): eth0: 172.16.16.1/24, eth1: 1.0.0.2/24 GW 1.0.0.1 S2 (Ubuntu 10.04 x64 Server): eth0: 10.0.0.1/24, eth1: 2.0.0.2/24 GW 2.0.0.1 S3 (Ubuntu 10.04 x64 Server): eth0: 1.0.0.1/24, eth1: 2.0.0.1/24, eth2: 3.0.0.1/24 +--+ +--+ +--+ +--+ +--+ |C1|-----|S1|-----|S3|-----|S2|-----|C2| +--+ +--+ +--+ +--+ +--+ | +--+ |C3| +--+ Server S1 and S2 provide NAT functionality. (they have routing enabled and provide a firewall, which allows trafic from the internal net and provide the nat functionality) Server S3 has routing enabled. The client firewalls are turned off. C1 and C2 are able to ping C3, e.g. visit C3's webserver. They are also able to send UDP Packets to C3 (C3 successful receives them)! C1 and C2 have also webservers running for test reasons. I run ""chownat -s 80 2.0.0.2"" at C1, and ""chownat -c 8000 1.0.0.2"" at C2. Then I tried to access the Webpage from C1 via webbrower localhost at port 8000. It didn't work. Can anybody help me? Any suggestions? If you have any questions to my question, please ask!

  Read the article

• i am not able to connect to the application hosted on port 80

  - by shiva

  I am trying to access an application that is hosted on port 80. When i try the url from my personal computer , the site is not reachable but the same url on the server( which hosts the application) i am able to access the site. When i disable the firewall then i am able to access the site from my pc. So there is some rule which is blocking this port. How do i determine what windows firewall rule is blocking this port. I have disables IIS as well. Kindly point me in the right direction

  Read the article

• Troubleshooting a network card on linux. Connected to network, given access point, no connection?

  - by Chris

  I installed the driver for my network card. iwconfig and ifconfig are all responsive to connecting to the network, I'm given an access point address. Then, I try to connect to a website and no dice. ping www.google.com yields no result. What gives?

  Read the article

• Trixbox CentOS Default GW Problem (Multi-homed server)

  - by slashp

  I'm having an issue with a CentOS trixbox server which is dual-homed (one private facing NIC [eth1], one internet-facing NIC [eth0]). I can't seem to get the default gateway to set properly to our ISP's GW via eth0. I've modified the /etc/sysconfig/network to contain both a GATEWAY & GATEWAYDEV line and removed the GATEWAY line from /etc/sysconfig/network-scripts/ifcfg-eth1 (as well as /etc/sysconfig/network-scripts/ifcfg-eth0). No default GW shows up in the routing table unless it's specified in the ifcfg-eth1 file (which both the wrong interface and wrong gateway IP), otherwise, the routing table simply does not contain a default gateway..any ideas would be greatly appreciated! Thanks! EDIT Just realized when attempting to add the default gateway manually using the route add command, I receive an error stating: SIOCADDRT: Network is unreachable I know this error can occur when your default gateway and interface IP address are not on the same subnet..in this case, my public IP address of eth0 is a /29.

  Read the article

• Enabling NAT loopback on HG556a router?

  - by galdikas

  This is one of the standard issue vodafone routers. So i set up web-server on my laptop, and it is accessible to the internet now. However I need to be able to access it from my machine using the public address. But I just cannot find where to enable nat loopback. I looked for options in both regular and advanced user logins (web interfaces). So I suppose the last option is telneting into it, and using commands to do it.. but I don't know how to access it (cant find the credentials). http://rhiggins.sdf-eu.org/blog/index.php?entry=entry110722-164625 In above link it says that i can find this info in configuration file, but anyone could tell me how to access it? And then what commands should I use to enable the NAT loopback?

  Read the article

• How to configure 2nd network card for use in VMWare Workstation?

  - by Timo

  Hi all, I am using VMWare Workstation 6.5, connected to my network with a bridged adapter so that the virtual machine OS (Windows XP) has its own IP adress. This just worked out of the box. Now my host machine (Windows Vista) has an additional network card that is directly connected to another computer using a crossover cable (and fixed IP adress 10.1.1.4, while the "main" network connection is using DHCP with IP in the 192.68.0.* range). How can I use that network connection as well in the virtual machine? Do I need to bridge my 2nd network adapter to some VMnetX adapter? Do I need to add a host virtual adapter? I do not know much about networks, and the VMWare network settings really confuse me :-) Thanks, Timo

  Read the article

• Anyone interested in obtaining a cable list from a visio Diagram? [closed]

  - by Alex

  it's my first post here. Just wondering if anyone had to deal with the following problem - you have to install over say a 100 network elements and servers - cabling is done via contractors, so you need to provide them with an accurate, error-free cable list - your inputs are a set of detailed, port by port, visio diagrams. Prb is to obtain the cable list and get the cabling started while you're busy crafting the switch/routers configs. I coded a Visio plugin, which I plan to release under the GNU license, that returns a cable list from a diagram, and tested it on intermediate size infrastructure, 2K+ cables. It works well. The tool needs a little work to be user friendly, so before getting started, I wanted to know if that was worth the effort. Questions are welcomed, let me know -A PS: the tool is targeted for those who need a port by port description of their network, in the form Source/slot/port/Destination/slot/port.

  Read the article

• How to fill in the network line in the ubuntu interfaces config file?

  - by matnagel

  I have to configure an ubuntu hardy server network interface. The service hoster told me that this is the network data for the machine: IP Range: 111.111.200.74 to 111.111.200.78 Netmask: 255.255.255.248 Broadcast: 111.111.200.79 Gateway: 111.111.200.73 Subnet: 111.111.200.72/29 I am only using the first IP address. I will update the /etc/hosts file with 111.111.200.74, but I am still unsure how the /etc/network/interfaces file should be. This is my plan: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 111.111.200.74 netmask 255.255.255.248 network 111.111.200.??? broadcast 111.111.200.79 gateway 111.111.200.73 As you can see I don't know how to build the network line. How would I calculate the data for the network line and what is the result? (I changed the first 2 octets of the subnet, they are not "111.111" in the real setup.)

  Read the article

• Printing on Windows 8 with PDF viewer (Adobe Reader) from network

  - by Bongo

  i have a problem with the Adobe Reader 8, but the problem seems to be equally bad with other pdf viewers. Here is the configuration: My PDF viewer is located on network drive "Z:" which is the network adress \dgs-main\progs. I tried to start the adobe reader from here - \\dgs-main\progs\Adobe\Reader 8.0\Reader\AcroRd32.exe and open the PDF from here - C:\Users\ServiceDesk\AppData\Local\Temp\GeneratedPDF.pdf The problem is as follows, if i open the PDF with a local PDF viewer everything works fine and i can print the document. If i open the PDF with the Network PDF viewer then it opens, but printing is impossible. The error message states: "Unable to start print job. Is printer available?" As mentioned above, it works with a local pdf viewer. In both cases i use the same printer. The Printer is a network printer but even with a local printer it fails. The error occurs only on Windows 8 machines. On windows 7 it works fine. I Hope somebody can tell me what the problem is. Thanks in advance and have a fine day.

  Read the article

• Facebook doesn't work on computer, but work on mobile device, both use the same router

  - by sasa

  I have a very strange problem and I'm thinking that can be problem with dns or something similar, but not sure and don't know how to solve. My computer is connected to router and every site works fine except facebook (Chrome and Firefox). Chrome shows "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." But, on mobile device witch is connected to the same router facebook works fine (Fb application and Delphin browser). Pinging facebook works fine. Clearing cookies and cache didn't help. Also, I performed antivirus and antimalware scan and there is nothing. What can be a problem? Update: I'm also connect notebook on that wifi router, and on it works fine. nslookup facebook.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: facebook.com Addresses: 2a03:2880:2110:3f01:face:b00c:: 2a03:2880:10:1f02:face:b00c:0:25 2a03:2880:10:8f01:face:b00c:0:25 69.171.224.37 69.171.229.11 69.171.242.11 66.220.149.11 66.220.158.11

  Read the article

• Easy shorewall question : allow ips to DNAT

  - by llazzaro

  Hello, At my home network I had a transparent proxy. This is the rule that forward all 80 traffic to my squid3.1 server at DMZ DNAT loc:!10.0.0.126 dmz:172.16.0.198:3128 tcp 80 - !172.16.0.198 Ok, I need to add more ips to avoid transparent proxy. I tried loc:!10.0.0.134,!10.0.0.126...but didnt work (also similars like [ip0,ip1]. I tried to google the answer cant find it (sorry no matches, not searching the right keywords) also I tried to read the docs, but they are really long (and indexes dont help me). Thanks!

  Read the article

• dig lookup different from system lookup

  - by simao

  Hello, I am running dd-wrt and I configured it's dns server to resolve a few hosts inside my network. When I use dig to lookup these hosts, they are resolved OK, but when I try to ping those hosts I always receive an unknown host error message. For example: obe:~ simao$ dig dd-wrt ; <<>> DiG 9.6.0-APPLE-P2 <<>> dd-wrt ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 44026 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;dd-wrt. IN A ;; ANSWER SECTION: dd-wrt. 0 IN A 192.168.1.1 But then: obe:~ simao$ ping dd-wrt ping: cannot resolve dd-wrt: Unknown host Any ideas? Thanks.

  Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >