Search Results

Search found 408 results on 17 pages for 'broadcom'.

Page 2/17 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Broadcom 4365 wireless driver with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• PS3 controller on Sixad disbales Broadcom Bluetooth

  - by Craggles

  The recipe for breaking blue tooth is so far: Fresh install - blue tooth is happy install broadcom drivers for wifi Update to latest ubu install sixad run it once through and check ps3 controller is working. reboot Bluetooth is dead or if I disable blue-tooth before reboot it won't come back either. Latest stable Ubuntu - inbuilt bluetooth module. Hp Probook 6470b. UPDATE Running sixad via: sudo apt-add-repository ppa:falk-t-j/qtsixa sudo apt-get update sudo apt-get install sixad Then: sudo sixpair sixad --start And turning off bluetooth to disconnect the PS3 controller and ctrl c the terminal means bluetooth can't be reactivated. Even after a reboot. Help is appreciated! I'm very new to Ubuntu so be gentle. UPDATE 2 Reinstalling bluez, fixes it...

  Read the article

• broadcom 43225 wireless on acer laptop is disabled

  - by Robbie

  I have a acer aspire 5820T with a broadcom 43225 wireless card. I previously used ubuntu 10.10 and the wireless worked straight away, but when I updated to 11.04 the wireless stopped working. I have managed to get the wireless hardware to switch on for a couple of seconds before turning off (When you turn the wireless on using the manual switch the wireless light stays on for a couple of seconds and in the drop down connections menu the information under wireless networks changes from 'device not ready' to 'Disconnected' but shows no wireless networks despite there being one). So far I have tried installing an additional driver, and also disabling the additional driver and installing b43-fwcutter and firmware b43 installer. There may have been other things that I've found in searches that i've tried but unfortunately I can't remember them. Any help would be appreciated.

  Read the article

• Broadcom 4365 wireless driver on 12.04 with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• Broadcom 4313 Signal strength very low on an HP Pavilion dv4

  - by thegreyspot

  I have a HP pavilion dv4 4141US laptop running fresh ubuntu 11.10. This laptop has a broadcom 4313gn chipset for the network card. The network card is using the brcmsmac driver. Which, I heard else where on askUbuntu that its the best driver to be using for this card. I can connect to my network, however I have extremely low network signal. Right now I am right in front of the router, and I only get 72%. If i go to the room directly behind the router's wall, i get no signal, where as with windows 7 I get a nice 70% percent. UPDATE: I use WEP at home and an open wireless connection at work. Both have same result. Both are completely different routers. Also you G What can i do?

  Read the article

• Broadcom bcm4313 Ubuntu 13.10 connection time out

  - by Wahtever

  After upgrading to Ubuntu 13.10 I keep getting connection timed out every few seconds at which point i have to disconnect and reconnect to the WiFi network. The WiFi card worked fine on 13.04 with the bcmwl-kernel-source installed but giving problems on 13.10: *-network description: Wireless interface product: BCM4313 802.11bgn Wireless Network Adapter vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: c0:14:3d:cc:c9:c7 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.4 latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f0500000-f0503fff How can i fix this? Thanks

  Read the article

• Broadcom brcm80211 installation from source

  - by calmpitbull

  Hello need help to get my wifi chipset working.I have brcmsmac driver and i would like to have brcm80211 chipset up and running. I have tried everything but nothing helped? git://git.kernel.org/pub/scm/linux/kernel/git/dwmw2/linux-firmware.git Copy brcm/bcm43xx-0.fw and brcm/bcm43xx_hdr-0.fw to /lib/firmware/brcm (or wherever firmware is normally installed on your system). still got brcmsmac ?? then i tryed git clone git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git git clone git://git.kernel.org/pub/scm/linux/kernel/git/dwmw2/linux-firmware.git cd ~/linux-next/drivers/staging/brcm80211 nano Makefile the problem is that there is no brcm82011 folder?? do i follow cd ~/linux-next-a694cb1 like the link sad? i have Broadcom Corporation BCM4313 [14e4:4727]

  Read the article

• Stable ubuntu distribution for a broadcom bcm4313 wireless driver and an nvidia 630 graphics adapter

  - by Vivek Pradhan

  I have been trying to completely shift to ubuntu or a linux distro for almost 2 years now. I have tried all the ubuntu distros starting from 10.04 through 11.10, but there has always been some bugs with the display drivers or the wireless cards not being recognised and the additional drivers suggested from the ubuntu community not doing the trick always. I tried a lot to fix bugs, checked a lot of forums, launch pad, got some of them fixed, but could not really get a neat and complete ubuntu machine set up till now. Now I really like the whole open source community and the linux platform, my pc at home runs ubuntu 11.04 perfectly but there have been some glitches always with ubuntu on my laptop that has forced me to stick with windows only. Now I am currently on an hp dv6 laptop that has the broadcom bcm4313 wireless driver and the nvidia 630gtm graphics(optimus) driver. Now I tried to do some research on the support of these drivers in linux machines but could not get anywhere. So I would really appreciate if you guys could suggest some linux distro that I could use that has full support of these drivers or has stable bug fixes for these kind of issues. I tried precise pangolin (LTS) through a live CD but i still see a problem with wifi networks which is a little frustrating. Please help me find the perfect match for my laptop :P I would gladly provide any other information necessary.

  Read the article

• Cannot enable Additional drivers for Broadcom in 12.10

  - by Compt

  tl;dr version: Additional Drivers does not work for enabling a driver in Ubuntu 12.10, however it worked in 12.04. I upgraded to Ubuntu 12.10 from 12.04 via a live USB. I did a fresh install to avoid any conflicts. From 12.04 I know that my wireless card has proprietary drivers that could be installed via Additional Drivers. I did eventually find additional drivers in the software sources menu, however when I attempt to switch to Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source, it not only does not work, it in fact disables my wireless completely. The only way to revert this is to restart, and revert back to "do not use the device". Then upon another restart, my wireless will function once again. I was curious if anyone else had this issue, and if there was a fix for it as of yet. I looked on launchpad and it may be a potential bug, but I am unsure. Any help would be greatly appreciated (and sorry for that wall of text). Until then, I'll continue to use my wireless as it is (or revert to 12.04), but I do notice a slower connection without it enabled.

  Read the article

• Wireless problems with Broadcom BCM4313 with windows7 (duplicate)

  - by user292394

  I have wireless connection problem can't connect my wireless adress lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no lsmod Module Size Used by bnep 19624 2 rfcomm 69160 8 ip6t_REJECT 12939 1 xt_hl 12521 6 ip6t_rt 13537 3 nf_conntrack_ipv6 18894 8 nf_defrag_ipv6 34768 1 nf_conntrack_ipv6 ipt_REJECT 12541 1 xt_LOG 17717 10 xt_limit 12711 13 xt_tcpudp 12884 18 xt_addrtype 12635 4 nf_conntrack_ipv4 15012 8 nf_defrag_ipv4 12758 1 nf_conntrack_ipv4 xt_conntrack 12760 16 ip6table_filter 12815 1 ip6_tables 27025 1 ip6table_filter nf_conntrack_netbios_ns 12665 0 nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns nf_nat_ftp 12770 0 nf_nat 21798 1 nf_nat_ftp nf_conntrack_ftp 18638 1 nf_nat_ftp nf_conntrack 96976 8 nf_nat_ftp,nf_conntrack_netbios_ns,nf_nat,xt_conntrack,nf_conntrack_broadcast,nf_conntrack_ftp,nf_conntrack_ipv4,nf_conntrack_ipv6 iptable_filter 12810 1 ip_tables 27239 1 iptable_filter vx_tables 34059 13 ip6table_filter,xt_hl,ip_tables,xt_tcpudp,xt_limit,xt_conntrack,xt_LOG,iptable_filter,ip6t_rt,ipt_REJECT,ip6_tables,xt_addrtype,ip6t_REJECT uvcvideo 80885 0 videobuf2_vmalloc 13216 1 uvcvideo videobuf2_memops 13362 1 videobuf2_vmalloc snd_hda_codec_hdmi 46207 1 videobuf2_core 40664 1 uvcvideo videodev 134688 2 uvcvideo,videobuf2_core snd_hda_codec_conexant 57441 1 snd_hda_intel 52355 8 snd_hda_codec 192906 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 102099 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 dm_multipath 22873 0 snd_seq_midi_event 14899 1 snd_seq_midi scsi_dh 14882 1 dm_multipath lib80211_crypt_tkip 17619 0 snd_rawmidi 30144 1 snd_seq_midi intel_powerclamp 14705 0 coretemp 13435 0 kvm_intel 143060 0 kvm 451511 1 kvm_intel joydev 17381 0 serio_raw 13462 0 snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi intel_ips 18664 0 wl 4207846 0 snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi btusb 32412 0 bluetooth 395423 22 bnep,btusb,rfcomm snd_timer 29482 2 snd_pcm,snd_seq snd 69238 26 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi lib80211 14381 2 wl,lib80211_crypt_tkip toshiba_bluetooth 12852 0 cfg80211 484040 1 wl lpc_ich 21080 0 fglrx 8085343 190 soundcore 12680 1 snd toshiba_acpi 22901 0 sparse_keymap 13948 1 toshiba_acpi wmi 19177 1 toshiba_acpi amd_iommu_v2 19054 1 fglrx video 19476 0 mei_me 18627 0 mei 82276 1 mei_me mac_hid 13205 0 parport_pc 32701 0 ppdev 17671 0 lp 17759 0 parport 42348 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 52570 0 hid 106148 2 hid_generic,usbhid psmouse 102222 0 ahci 25819 3 libahci 32168 1 ahci atl1c 46086 0 dm_mirror 22135 0 dm_region_hash 20862 1 dm_mirror dm_log 18411 2 dm_region_hash,dm_mirror Can someone give any ideas on how I can fix my wireless

  Read the article

• Wireless Drivers for Broadcom BCM 4321 (14e4:4329) will not stay connected to a wireless network

  - by Eugene

  So, I'm not necessary new to Linux, I just never took the time to learn it, so please, bare with me. I just swapped out one of my wireless cards from one computer to another. This wireless card in question would be a "Broadcom BCM4321 (14e4:4329)" or actually a "Netgear WN311B Rangemax Next 270 Mbps Wireless PCI Adapter", but that's not important. I've tried (but probably screwed up in the process) installing the "wl" , "b43" and "brcmsmac" drivers, or at least I think I did. Currently I have only the following drivers loaded: eugene@EugeneS-PCu:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd The main issue is that with most of the drivers available that I've installed, they will find my wireless network but, they will only stay connected for about a minute with abnormally slow speed and then all of a sudden disconnect. Currently, the computer is hooked into another to share it's connect so that I can install drivers from the internet instead of loading them on to a flash drive and doing it offline. If anyone has any insight to the problem, that would be awesome. If not, I'll probably just look up how to install the Windows closed source driver. Edit 1: Even when I try the method here, as suggested when this was marked as a duplicate, I still can't stay connected to a wireless network. Edit 2: After discussing my issue with @Luis, he opened my question back up and told me to include the tests/procedures in the comments. Basically I did this: Read the first answer of the link above when this question was marked as duplicate which involved installing removing bcmwl-kernel-source and instead install firmware-b43-installer and b43-fwcutter. No change of result and contacted Luis in the comments, who then told me to try the second answer which involved removing my previous mistake and installing bcmwl-kernel-source Now the Network Manger (this has happend before, but usally I fixed it by using a different driver) even recognizes WiFi exist (both non-literal and literal). Luis who then suggested sudo rfkill unblock all rfkill unblock all didn't return anything, so I decide to try sudo rfkill list all. Returns nothing (no wonder rfkill unblock all did nothing). I enter lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" and that returns nothing. Try loading the driver by entering sudo modprobe b43 and try lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" again. Returns this: eugene@Eugenes-uPC:~$ sudo modprobe b43 eugene@Eugenes-uPC:~$ lsmod | grep "brcmsmac\|b43\|ssb\|bcma\|wl" b43 387371 0 bcma 52096 1 b43 mac80211 630653 1 b43 cfg80211 484040 2 b43,mac80211 ssb_hcd 12869 0 ssb 62379 2 b43,ssb_hcd So to recap: Currently Network Manager doesn't recognize Wireless exists, b43 drivers are loaded and I've currently hardwired a connect from my laptop to the computer that's causing this.

  Read the article

• Wireless Broadcom 4313 not working on Ubuntu 12.04

  - by user88568

  It seems a lot of people are having this problem, but none of the posted solutions have worked for me so far. My driver is installed and activated, I have tried removing and re-adding the network, and various other fixes. No networks were picked up on my first boot, the next day wireless worked fine, and since then it does not detect networks, and when I manually try to connect, it repeatedly asks for the password and does not connect. Here's my info: 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f0500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-a1-ff-ff-f3-70-f1 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac root@michelle-laptop:/home/michelle# ifconfig eth0 Link encap:Ethernet HWaddr 70:f1:a1:f3:ba:ab inet6 addr: fe80::72f1:a1ff:fef3:baab/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:29 TX packets:0 errors:30 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 eth1 Link encap:Ethernet HWaddr f0:4d:a2:53:83:7a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:104 errors:0 dropped:0 overruns:0 frame:0 TX packets:104 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8000 (8.0 KB) TX bytes:8000 (8.0 KB) root@michelle-laptop:/home/michelle# lsmod Module Size Used by dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_realtek 174313 1 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event parport_pc 32114 0 ppdev 12849 0 binfmt_misc 17292 1 lib80211_crypt_tkip 17275 0 bnep 17830 2 rfcomm 38139 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq joydev 17393 0 wl 2646601 0 snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd btusb 17912 0 bluetooth 158438 11 bnep,rfcomm,btusb uvcvideo 67203 0 videodev 86588 1 uvcvideo snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lib80211 14040 2 lib80211_crypt_tkip,wl intel_ips 17822 0 psmouse 72919 0 serio_raw 13027 0 mei 36570 0 dell_laptop 17767 0 dell_wmi 12601 0 dcdbas 14098 1 dell_laptop sparse_keymap 13658 1 dell_wmi mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid wmi 18744 1 dell_wmi i915 414817 3 atl1c 36718 0 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 root@michelle-laptop:/home/michelle# iwlist scan lo Interface doesn't support scanning. eth1 Interface doesn't support scanning. eth0 No scan results root@michelle-laptop:/home/michelle# rfkill list 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no Obviously I don't know what I'm doing. I'd appreciate any help! Thanks!

  Read the article

• Xubuntu 14.04 install fails on Dell Inspiron B130 with Broadcom 4318

  - by K7AAY

  I have a Dell Inspiron B130 I am trying to install 32-bit Xubuntu 14.04 on. The install of 13.10 was AOK but the update failed catastrophically, so I am reinstalling from scratch. WiFi and the Ethernet port work AOK in Windows 8.1u1 (70 secs to boot) and Mint 16 Cinnamon (135 secs to boot), but neither work in 14.04 and the install fails on the Dell; it won't find the network (which also fails on Bodhi 32-bit). Since any install fails whether or not I have an Internet connection (with "An attempt to configure apt to install additional packages from the CD failed") whether or not I select to update apps in the install, whether or not I choose to install MP3 and other Multiverse items, I am unable to install then go get drivers.

  Read the article

• broadcom BCM4318 firmware missing

  - by Lucas

  I tried sudo apt-get update && apt-cache search b43 sudo apt-get install firmware-b43-installer after that i get this error Can't update, Some index files failed to download i tried cd /var/lib/apt/lists/partial sudo rm gb.archive.ubuntu.com_ubuntu_dists_natty_multivers e_source_Sources OR sudo rm /var/lib/apt/lists/partial/gb.archive.ubuntu.com_ubuntu_dists_natty_multivers e_source_Sources another error cannot remove e_source_Sources

  Read the article

• Slow Wireless Reconnect After Suspend - Broadcom 4312 with STA drivers

  - by nrhine1

  I am using 10.10 with STA drivers, I reinstalled ubuntu because the b43 drivers were giving me a huge hassle along with some weird kernel issues. My wireless speed is fine, everything works well, except upon restart of computer and after taking the computer out of suspend. It takes about 30-45 seconds for the wireless to reconnect, and I think it is a driver issue (I clicked on the network manager at the top and for about 30 seconds there are no wireless networks listed.) I tried this advice already: http://lilserenity.wordpress.com/2007/10/31/fix-ubuntu-dropping-wireless-on-suspendhibernate-resume/ which basically says to change this: STOP_SERVICES="" to STOP_SERVICES="networking" in the file /etc/default/acpi-support This did not help anything. Something to note is that the issue does not occur when I am logging back in after already logging in once and logging out.

  Read the article

• Network Issues only on one network with a Broadcom BCM4312

  - by Ryan McClure

  My Ubuntu 11.10 laptop is having network connection issues...only on one network. I have a BCM4312 card and I'm using the proprietary driver. Whenever I connect to a network over wireless connection, I have no trouble except for one network. In my dorm, if I try to connect to the wireless network, it stays connected from anywhere to 30 seconds to 30 minutes before it will still be "connected" according to the indicator but there is no incoming/outgoing internet connection. This only happens in this building. Other networks with the same name at other buildings on my campus have no issue whatsoever. I took it to the tech department here and they keep claiming it's my laptop; but, if I can connect to other networks with absolutely no issues, why can't my laptop connect here? So, here's my question: Is it my laptop, or is it the network? As a side note, no one else that I know has issues on this network but one; she's running Windows 7 and I forget what kind of laptop it is. One of the people in my hall runs Ubuntu 12.04 and has no problem with the wireless. What do you all think of this?

  Read the article

• Broadcom BCM4313 wireless slow and high-latency

  - by Florin Andrei

  Ubuntu 12.10 64 bit on a Dell Latitude E6330 laptop. Wireless is pretty slow. It gets connected quick enough, but then it acts like a dialup connection. My ssh sessions over WiFi are slow and laggy. Even browsing is slow, the pages are loading like it's 1998. This does not depend on the access point, it's the same both at home and at work. Other systems work fine on these access points. I had an older Dell laptop before, different WiFi hardware, and it was much faster over the same wireless access points. Is this a known issue with this hardware? If so, any solutions?

  Read the article

• Connect WPA networks using Broadcom BCM4315

  - by Natim

  I just installed Ubuntu 14.04 LTS on my HP computer I installed the BCM43 driver I used @Wild Man script to get you some informations: wget -N -t 5 -T 10 http://dl.dropbox.com/u/57264241/wireless_script && chmod +x wireless_script && ./wireless_script Here: http://paste.lolnet.org/paste/kOil1BvT#psOHgxeF As you can see on the file, everything looks good, WEP,WPA,WPA2 but my wifi which is a WPA-PSK password doesn't appears on the network list. Do you have any idea of what could be wrong?

  Read the article

• Ubuntu 12.10 Broadcom Wireless BCM43225

  - by DanFritz

  During the installation of my Ubuntu 12.10 I could use the wireless connection for extra updates. After the installation I updated Ubuntu and it installed 74 new updates, after that no wireless connection (say what!). So I did try some stuff, I followed the tutorial to load the windows drivers using ndiswrapper (https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper) but I always get that the ndiswrapper module is not loaded (but I did install the extra 3 packages, still doesnt work). ndiswrapper-source ndiswrapper-dkms ndiswrapper-common Please somebody help! Thanks a lot

  Read the article

• Dell Studio 15 Broadcom wireless drivers not working in Linux Mint

  - by dcd0687

  I installed Linux Mint 12 on my Dell Studio 15 and everything worked perfectly up until I tried updating the STA Driver for the Broadcom (BCM4312) wireless controller. I've tried these bash commands in order and I still don't have wireless. sudo apt-get install b43-fwcutter sudo apt-get install b43-fwcutter firmware-b43-installer I've also tried uninstalling everything with synaptic package manager including broadcom-sta-common and broadcom-sta-source, then restarting and running the above commands which didn't work either. What's the best way to do this on a Dell Studio 15?

  Read the article

• Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe driver tg3 will not install?

  - by Pete

  aries@aries-laptop:~$ sudo ifconfig eth0 up eth0: ERROR while getting interface flags: No such device aries@aries-laptop:~$ lspci -nn 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1705] 00:01.0 VGA compatible controller [0300]: ATI Technologies Inc Device [1002:9641] 00:01.1 Audio device [0403]: ATI Technologies Inc Device [1002:1714] 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:1709] 00:06.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:170b] 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] Device [1022:7800] (rev 40) 00:12.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:12.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:13.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:13.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] Device [1022:780b] (rev 13) 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] Device [1022:780d] (rev 01) 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] Device [1022:780e] (rev 11) 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:780f] (rev 40) 00:16.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) 00:16.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1700] (rev 43) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1701] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1702] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1703] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1704] 00:18.5 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1718] 00:18.6 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1716] 00:18.7 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1719] 01:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe [14e4:16b5] (rev 10) 01:00.1 SD Host controller [0805]: Broadcom Corporation Device [14e4:16bc] (rev 10) 01:00.2 System peripheral [0880]: Broadcom Corporation Device [14e4:16be] (rev 10) 01:00.3 System peripheral [0880]: Broadcom Corporation Device [14e4:16bf] (rev 10) 02:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4358]

  Read the article

• Broadcom BCM5716 Hangs on CentOS 6 Boot

  - by someotherguy

  I have a fresh CentOS 6 installation on a Dell R310 server with a Broadcom BCM5716. The onboard NIC is causing the boot to hang for some reason. Welcome to CentOS Linux Starting udev: udev: starting version 147 Boardcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.23b (Feb 01, 2011) bnx2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 That's it... then it just hangs / freezes. If I disable the NIC via the BIOS settings, CentOS boots fine. I've downloaded and installed the latest driver from Broadcom's website. Any ideas?

  Read the article

• Linux live cd with Broadcom Wi-fi support

  - by paul simmons

  I am looking for a live distro that has out of the box Broadcom wireless support. I am pretty happy with my Ubuntu installation and as long as I have an ethernet connection first time installed, I can install Broadcom drivers over internet. But being a little paranoid, I make my secure operations (banking etc.) with a live cd and zero hard disk access, so nothing is recorded. So far I plug ethernet to do such things with the live cd, but it would be nice if I can do same thing with wireless.

  Read the article

• no internet - broadcom NetXtreme BCM755 linux

  - by iamrohitbanga

  i have opensuse 11.0 on a PC with Broadcom NetXtreme BCM 755 ethernet adapter. i am not able to connect to the internet. what could be the problems. how to solve it?

  Read the article

• Broadcom 440x Ethernet NIC Drivers and Windows Home Server

  - by scottman666

  I have installed Windows Home Server on an older Dell computer, and it uses a Broadcom 440x Ethernet NIC driver. I have tried all of the drivers listed on their drivers page to no luck. The error message I get when trying to install is: "The parameter is incorrect" I know it is a long shot, but anybody have any suggestions? Thanks!

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >