Search Results

Search found 408 results on 17 pages for 'broadcom'.

Page 1/17 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How to get Broadcom BCM 43XX Wireless card working

  - by Fer1805

  NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

• No Wireless Connection on a Broadcom BCM43227

  - by Nicolas

  I´ve installed Ubuntu 11.10 on my Acer Aspire Laptop and can´t get any Wireless connection. Where is my problem? My wireless card is an Acer Nplify(TM) 802.11b/g/n. Thanks in Advance @mikewhatever: nic@ubuntu:~$ lspci -nnk | grep -iA2 net Kernel driver in use: tg3 -- 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe [14e4:16b5] (rev 10) Subsystem: Acer Incorporated [ALI] Device [1025:0504] Kernel driver in use: sdhci-pci 02:00.1 SD Host controller [0805]: Broadcom Corporation NetXtreme BCM57765 Memory Card Reader [14e4:16bc] (rev 10) Subsystem: Acer Incorporated [ALI] Device [1025:0504] 03:00.0 Network controller [0280]: Broadcom Corporation BCM43227 802.11b/g/n [14e4:4358] Subsystem: Foxconn International, Inc. Device [105b:e040]

  Read the article

• Replace Broadcom "wl" driver with "b43"

  - by Laszlo Boros

  I'm using Ubuntu 10.04.4 LTS, and in my laptop there is a Broadcom BCM4312 wlan card. lspci output: 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) Subsystem: Broadcom Corporation Device 04b5 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f4500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 81-ac-1d-ff-ff-12-54-92 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, ssb So as you can see, the current (and default) driver is wl - installed with jockey. But I have another Ubuntu based distribution on my laptop (BackTrack linux), which is also 10.04, but it has the b43 driver installed and the overall performance is MUCH better. So I would like to install it on this OS too, but even google didn't help me. So my question is how to install the latest b43 driver on my Ubuntu?

  Read the article

• Installing Broadcom Wireless Drivers

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. What are the steps to install Broadcom wireless drivers for a BCM43xx card? I'm a user with no advance knowledge in Linux, so I would need clear explanations on how to make, compile, etc. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] iwconfig showed: lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• 13.10 - Weird WiFi connection problems - WMP300N - Broadcom BCM4321

  - by user1898041

  Just installed 13.10 on my desktop and I really like it. After having problems with getting the wifi to work, I installed it connected to the internet with an ethernet cable and added in the 3rd party software and updates as per the installation procedure. After installation was completed, I saw the wifi icon in the upper right hand corner, but it was not seeing any wifi networks. Some Googling brought me to use the 'Additional Drivers' application. It found the WMP300N Broadcom BDM4321 based pci wifi card and installed the proprietary Broadcom STA wireless driver, which may have been installed before. I'm not sure. Here is the weird part: when I start my system, wifi seems to be in some sort of suspended state where the system sees that the card exists but the card will not detect any wifi networks. It will work after booting once I 'Additional Drivers' application and then start FireFox. I know it seems weird, but this is the process I've got down to get the card to recognize wifi networks. After those applications are open for a few seconds, the card starts to function like normal (although maintaining the wifi connection is problem but most likely a seperate issue). The reason this is a problem is because this is supposed to just be a headless box managed through SSH. Here are the readouts from the common network diagnosis programs BEFORE I open 'Additional Drivers' and 'FireFox'. All commands were done with sudo. lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) - iwconfig eth1 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off - iwlist scan eth1 No scan results - Here are the various commands AFTER I open 'Additional Drivers' and 'FireFox' lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.103 latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:85 errors:0 dropped:0 overruns:0 frame:11901 TX packets:132 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52641 (52.6 KB) TX bytes:19058 (19.0 KB) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6084 (6.0 KB) TX bytes:6084 (6.0 KB) - iwconfig eth1 IEEE 802.11abg ESSID:"BU" Mode:Managed Frequency:2.447 GHz Access Point: 00:26:F2:1F:81:02 Bit Rate=54 Mb/s Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=59/70 Signal level=-51 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - iwlist scan A LOT OF SSIDs FOUND! - I'd like to have this problem fixed, but I'm not quite sure where to go. Been Googling a lot and can't seem to find anyone else with this problem.

  Read the article

• Where to download Broadcom STA .deb file?

  - by Argusvision

  Situation: I don't have wireless access through Ubuntu due to needing the Broadcom STA driver for my wireless card. I don't currently have access to a physical (cabled) connection that will allow my Ubuntu machine access. (Security reasons, no unidentified machines.) Where can I download a .deb file for the Broadcom STA driver? I'm not asking how to install through jockey-gtk (the "Additional Drivers" menu option) or through Synaptic. Thank you in advance for any assistance.

  Read the article

• How do I get a Broadcom BCM4311 working?

  - by Fer1805

  I'm having serious problems installing the broadcom drivers for ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. Broadcom BCM4311 Wireless not working Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

  Read the article

• dell vostro 1000 broadcom wireless connection

  - by lorrenuy

  I have a problem with the hardware broadcom wifi. I press the hotkey fn+f2 to activate the hardware and this will not work. I'll look at the drivers but it appears to be installed. How can I solve this problem? Ubuntu is all new to me so if possible, give me a clear explanation. Now do I connect the lan cable. I use the Ubuntu 11.10 lawrence@lawrence-Vostro-1000:~$ sudo lshw -class network [sudo] password for lawrence: PCI (sysfs) *-network description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:c0200000-c0203fff *-network description: Ethernet interface product: BCM4401-B0 100Base-TX vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:08:00.0 logical name: eth1 version: 02 serial: 00:1c:23:a2:b9:a9 size: 100Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=full ip=192.168.1.18 latency=64 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:21 memory:c0300000-c0301fff lawrence@lawrence-Vostro-1000:~$ lawrence@lawrence-Vostro-1000:~$ rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• Broadcom STA driver doesn't work well with BCM4313

  - by Oli

  Following on from my other question about our new Samsung Q330, I've noticed that the wireless is incredibly flakey. It can connect but after a little use, especially if it does a lot of downloading at once (read: install something from the Software Centre), the connection stops working. Network Manager still see the connection, there's just no network throughput. I've simple tests like pinging other local network hosts and they just fail. The Samsung Q330 has a Broadcom BCM4313 wifi card (it's proper ID: 14e4:4727) and it's running on the Broadcom STA drivers that Jockey suggests (it didn't work at all without this). I did try installing b43-fwcutter but this just didn't do anything. I was expecting a configuration screen to come up (to select a firmware) but it never did. This page suggests the newer brcm80211 driver might be able to help, but I don't know how to install that. If you think this is the right route, please let me know how one goes about installing it.

  Read the article

• Broadcom wireless card disappeards on restart

  - by Kristian Jones

  I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

  Read the article

• Acer Aspire One 722 broadcom 4313 wifi

  - by Colin Matheson

  I had an Acer Aspire One 722 with the Atheros Wifi card and it worked fine on 11.04. So we bought 200 of them for our school. However these all came with the Broadcom BCM4313 wireless card and there are issues. It is using the brcmsmac driver and they connect initially. However after a time (sometimes just a few webpages) some of them lose connection. However, they still have an IP and network-manager says they are connected, but no pages load and you can't ping anything on the LAN or internet. A disconnect/reconnect can fix it, but sometimes a restart is required. It happens frequently so is a major issue. Lots of broadcom drivers are blacklisted: bcm43xx, b43, brcm80211. Any ideas or experiences with the broadcom4313 card? Please save these computers from a Windows fate!

  Read the article

• Broadcom BCM4313 working, but terribly slow

  - by Ataraxio Panzetta

  Hi all, I've installed ubuntu on a Asus 1015 netbook. Everything worked out of the box except for the Wireless adapter, which i had to install with the Additional Drivers application. It apparently installed fine and connects to our wireless network, but it only works at a "funny" speed range that goes from 367Bytes to a peak of 3Kb in its best moments. I know for sure the problem is neither the network nor the hardware. Network speeds are normal under windows on this laptop and in other computers with ubuntu aswell. lspci says the card is a BCM4313 model, but the Addittional Drivers Manager says these packecege contains Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4321-, and BCM4322 based hardware seems like it installed the wrong driver... Is there anything I can do? I'm not concerned about compiling the driver or stuff like that, but I'm not sure on where to start... any help or guidance will be very, very appreciated.

  Read the article

• Can't get Broadcom 43142 drivers to work after installation on 5420 Inspiron

  - by beckett

  I'm a complete newbie to ubuntu, I've already installed and reinstalled the Broadcom driver required done a numerous amount of steps on terminal but I can't seem to get wireless working. However, my wired connection seems to work just fine. also I have tried to follow the instructions but get stuck at step number 2 when i get told "No package dpkg is available": 1) Download the file from the link 2) sudo yum install dpkg 3) mkdir BCM43142 4) dpkg-deb -x Downloads/wireless-bcm43142-dkms-6.20.55.19_amd64.deb BCM43142 5) cd BCM43142/usr/src/wireless-bcm43142-oneiric-dkms-6.20.55.19~bdcom0602.0400.1000.0400/src/wl/sys 6) sudo yum install kernel-devel kernel-headers 7) vi wl_linux.c 8) around line 43, remove the line include 9) save the file (:wq) 10) cd ../../.. 11) make Things should work, and you'll have a file called "wl.ko" in the current directory. 12) sudo yum remove broadcom-wl 13) sudo mkdir -p /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 14) sudo cp wl.ko /lib/modules/3.5.2-3.fc17.x86_64/extra/wl 15) sudo depmod -a 16) sudo modprobe wl I really need help :/

  Read the article

• Installing Broadcom Drivers on Ubuntu 12.04

  - by HDInfinity

  I downloaded Ubuntu 12.04 so that I could Dual boot between Ubuntu and Vista. I am currently using a Broadcom 802.11.n Network Adapter for internet, I DON'T have access to an Ethernet connection. Is there a way for me to install the Broadcom drivers for Ubuntu while running Vista, then just install the drivers on Ubuntu from my Vista files. Or put the Drivers on a USB and install from there. There is no way for me to get an internet connection on Ubuntu without the Broadcam drivers.

  Read the article

• Broadcom STA wireless driver frezees

  - by Srki

  Upon updating my 10.10 netbook to 11.04 on the first startup it froze. I checked the forums and found that disabling wlan in BIOS fixes the problem so I did that and it worked, system was ok and it didn't freeze but then I had no wireless. I know that Broadcom STA driver is to blame cause I removed it from "additional drivers" and enabled back in bios wlan and everything worked fine (exept no wireless cause no driver is activated). Enabling Broadcom STA in the additional drivers again and restarting wireless was up and it found my network and connected to it but in a matter of seconds netbook froze. Can you please help me...

  Read the article

• Broadcom wireless card disappears after restart

  - by user10854

  I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. Within jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

  Read the article

• Broadcom 4312 wireless not working on an HP dv6-1245 DX

  - by vitalie

  I have installed Ubuntu 10.04 on my HP dv6-1245 dx notebook and I do not have any wifi (it worked perfectly in windows vista and 7). I have followed a lot of instructions found on net but still not able to get Internet. Here is the outcome of lspci: $ sudo lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem (rev 03) 02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) I have used ndiswrapper and have installed it, as well as the windows drivers for Broadcom, no change.

  Read the article

• Firmware/driver for Broadcom wifi card, PowerBook G4 running Ubuntu 12.04 [duplicate]

  - by user107831

  This question already has an answer here: How to Install Broadcom Wireless Drivers 40 answers This is my first time working with Ubuntu (or Linux), so please be patient. I am running Ubuntu 12.04-powerpc "Precise Pangolin" on a Mac PowerBook G4 with 1.67GHz processor. The firmware/driver for the wifi card is missing. For reasons not worth explaining, I cannot physically plug the computer into the network. I have another computer, a MacBook Pro running OSX, from which I can download files and port them by USB thumb drive. The wifi card in the PowerBook G4 is by Broadcom. The chip is BCM4306, rev. 3. The PCI number is 14e4:4302. I have downloaded b43-fwcutter_015-14_powerpc.deb and dropped it into the Home folder on the Ubuntu machine. However, it will not install. When I double-click, it opens with Ubuntu SoftwareCenter, but the "Install" button is inactive: I can't click it. There's a message beside the inactive button saying, "An older version of 'b43-fwcutter' is available in your normal software channels. Only install this file if you trust the origin." If I "right-click" the .deb file and open with Archive Manager, it shows me the "DEBIAN" and "usr" folders, but I'm unsure what to do from there...and fairly certain this is not the right way to do things. Maybe I have the wrong version of b43-fwcutter for my machine/version of Ubuntu? The documentation for this problem is a mess. It refers to all sorts of out-of-date Ubuntu versions and to an array of different "cutter" and firmware files. Maybe I'd be able to figure this out if I were a more seasoned Ubuntu user, but I have no idea why Sofware Center won't let me do the install. I would be VERY grateful for an explanation of how to get the wifi card working on this machine again. Thank you!

  Read the article

• Broadcom BCM4313 takes ages to connect

  - by Drazgo

  I'm having issues with my broadcom BCM4313 wireless adapter. Everything works just fine when connected (with additional drivers & Connman), but it takes about 5 minutes to connect to my network when i just started my computer! When resuming from hibernation it goes very quick though, so just when I boot my pc it's taking forever... This is what I found in the dmesg output: [ 16.778057] eth1: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.60.48.36 [ 16.808768] type=1400 audit(1295859939.727:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient3" pid=833 comm="apparmor_parser" [ 16.808815] type=1400 audit(1295859939.727:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=799 comm="apparmor_parser" [ 16.808825] type=1400 audit(1295859939.727:4): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient3" pid=826 comm="apparmor_parser" [ 16.809367] type=1400 audit(1295859939.727:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=833 comm="apparmor_parser" [ 16.809415] type=1400 audit(1295859939.727:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=799 comm="apparmor_parser" [ 16.809435] type=1400 audit(1295859939.727:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=826 comm="apparmor_parser" [ 16.809705] type=1400 audit(1295859939.727:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=833 comm="apparmor_parser" [ 16.809755] type=1400 audit(1295859939.727:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=799 comm="apparmor_parser" [ 16.809769] type=1400 audit(1295859939.727:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=826 comm="apparmor_parser" [ 16.844083] alloc irq_desc for 22 on node -1 [ 16.844087] alloc kstat_irqs on node -1 Any ideas how come? Thanks in advance!

  Read the article

• Broadcom 4313 doesn't work following 12.04 upgrade

  - by Lucas

  I have an hp G62-228Ca laptop with a BCM4313 previously running Ubuntu 11.10. I ran the 12.04 upgrade last night without much thought. Following the upgrade and mandatory reboot, the wireless card no longer shows up in the network manager, the first time I've had any kind of issues with wireless under Ubuntu. I've done much Googling on the issue but so far I haven't found a permanent solution. Mucking around with some packages though (I've installed five different ones or so), I've managed to devise a workaround that I must run every time I boot the laptop. I have to remove the Broadcom STA driver and reinstall it. Inspiration taken from here: WiFi does not work, Broadcom STA Wireless driver does not work on a BCM4313 After the second modprobe command, the wireless reappears in the network manager and ten seconds after that I'm back on the wifi. If anyone can provide some advice on how to fix this permanently I will be extremely grateful. I'd rather not roll back to 11.10 or reinstall, but I will if I need to. Just let me know if you need the output from any terminal commands. Thanks in advance!

  Read the article

• Broadcom BCM4331 not working on new Mac Mini 5,1

  - by Jon

  I can't seem to get my wireless card working on my Mac Mini 5,1. Lspci returns: 03:00.0 Network controller: Broadcom Corporation BCM4331 802.11a/b/g/n (rev 02) But running "additional drivers" doesn't detect anything. The nm-applet menu reads "device not ready--firmware missing." What can I do to get this to work? Note, this is with 12.04.1, so many of the previous discussions (for 11.10, etc) probably don't apply here.

  Read the article

• Broadcom BCM4312 Not Working

  - by ptran221

  I have a HP MINI 210-1010NR and just installed Ubuntu 11.04 and I can't get my wireless to work.I have checked through multiple Q&A's throughout this FAQ and tried them all. When I go over the wireless thing at the top it says "Wireless Networks device not ready(firmware missing)." Okay, now here is my lspci -vvnn | grep 14e4 02:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] (rev 01) Also, when I try to open additional drivers it says that "Downloading package indexes failed, please check your network status."

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >