Search Results

Search found 26900 results on 1076 pages for 'link to remote'.

Page 203/1076 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• xen debian: domU can't get out side

  - by iftol

  hi every body. i'm a trainee as a sysAdmin, it is my first expérience with virtualization. i have a server setup debian xen 3 with 2 physical interfaces. eth 0 for local network 10.0.0.1 and eth1 for internet (194.X.X.4). i created 3 VMs (web server, mail server and dabase server) with local ip addresses 172.10.0.x/24. the problem i had first is that domU can't ping dom0. i asked the sysAdmin of our ISP and he sais that he fogot to setup the bridginb. so he ceated a bridge with 172.10.0.1/24 after that i was able to ping the real server (194.X.X.4). but i can't go out side from my VMs, how can i fixe this issue? real or physical server ifconfig eth0 Link encap:Ethernet HWaddr 23:26:34:84:ce:xe inet adr:10.1.3.12 Bcast:10.1.3.255 Masque:255.255.255.0 adr inet6: fe80::226:b9ff:fe84:ceb4/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:412006 errors:0 dropped:0 overruns:0 frame:0 TX packets:411296 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 RX bytes:31410957 (29.9 MiB) TX bytes:31178370 (29.7 MiB) Interruption:36 Mémoire:d6000000-d6012100 eth1 Link encap:Ethernet HWaddr 23:26:34:84:ce:xe inet adr:194.x.x.4 Bcast:194.254.167.255 Masque:255.255.255.0 adr inet6: fe80::226:b9ff:fe84:ceb6/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:25872332 errors:0 dropped:0 overruns:0 frame:0 TX packets:414578 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:2642278343 (2.4 GiB) TX bytes:35436775 (33.7 MiB) lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1308073 errors:0 dropped:0 overruns:0 frame:0 TX packets:1308073 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:109871395 (104.7 MiB) TX bytes:109871395 (104.7 MiB) peth1 Link encap:Ethernet HWaddr 23:26:34:84:ce:xe UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:31818694 errors:0 dropped:0 overruns:0 frame:0 TX packets:414818 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 RX bytes:5197318822 (4.8 GiB) TX bytes:37904897 (36.1 MiB) Interruption:48 Mémoire:d8000000-d8012100 vif281.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff adr inet6: fe80::fcff:ffff:feff:ffff/64 Scope:Lien UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:207 errors:0 dropped:0 overruns:0 frame:0 TX packets:298 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 lg file transmission:32 RX bytes:24629 (24.0 KiB) TX bytes:28404 (27.7 KiB) vif281.1 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff adr inet6: fe80::fcff:ffff:feff:ffff/64 Scope:Lien UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:45 errors:0 dropped:47063 overruns:0 carrier:0 collisions:0 lg file transmission:32 RX bytes:0 (0.0 B) TX bytes:4449 (4.3 KiB) vif282.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff adr inet6: fe80::fcff:ffff:feff:ffff/64 Scope:Lien UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:78 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 lg file transmission:32 RX bytes:5041 (4.9 KiB) TX bytes:714 (714.0 B) xenbr0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff inet adr:172.10.0.1 Bcast:172.10.0.255 Masque:255.255.255.0 adr inet6: fe80::5c72:c6ff:fe49:7fe/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7180 errors:0 dropped:0 overruns:0 frame:0 TX packets:8615 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:756804 (739.0 KiB) TX bytes:791206 (772.6 KiB) brtcl show bridge name bridge id STP enabled interfaces eth1 8000.0026b984ceb6 no peth1 vif281.1 xenbr0 8000.feffffffffff no vif281.0 vif282.0 network-multi-bridge /etc/xen/scripts/network-virtual start vifnum="0" bridgeip="172.10.0.1/24" brnet="172.10.0.0/24" VM webserver eth0 Link encap:Ethernet HWaddr 00:16:3E:42:33:70 inet addr:172.10.0.2 Bcast:172.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe42:3370/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:126 (126.0 b) TX bytes:2036 (1.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Thank you for your help.

  Read the article

• Why wireless adatper stop to work?

  - by AndreaNobili

  today I correctly installed the driver for the TP-LINK TL-WN725N USB wireless adapter on my RaspBerry Pi (I use RaspBian that is a Debian), then I setted up the wifi using the wpa-supplicant as explained in this tutorial: http://www.maketecheasier.com/setup-wifi-on-raspberry-pi/ This worked fine untill this evening. Then suddenly it stopped to work when I try to connect in SSH and the Raspberry is on the wireless (or rather it should be, as this is not in the list of my router's DHCP connected Client) The strange thing is that the USB wirless adapter blink so I think that this is not a driver problem. If I try to connect it by the ethernet I have no problem. It appear in my router's DHCP connected Client and I can connect to it by SSH. When I connect to it using ethernet if I perform an ifconfig command I obtain: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.9 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:59 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6006 (5.8 KiB) TX bytes:8268 (8.0 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1104 (1.0 KiB) TX bytes:1104 (1.0 KiB) wlan0 Link encap:Ethernet HWaddr e8:94:f6:19:80:4c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So it seems that the wlan0 USB wireless adapter driver is correctly loaded. If I remove the USB wireless adapter and put it again into the USB port, the lasts lines of dmesg log is: [ 20.303172] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 20.306340] RTL871X: set bssid:00:00:00:00:00:00 [ 20.306726] RTL871X: set ssid [g\xffffffc6isQ\xffffffffJ\xffffffec)\xffffffcd\xffffffba\xffffffba\xffffffab\xfffffff2\xfffffffb\xffffffe3F|\xffffffc2T\xfffffff8\x1b\xffffffe8\xffffffe7\xffffff8dvZ.c3\xffffff9f\xffffffc9\xffffff9a\xffffff9aD\xffffffa7\x1a\xffffffa0\x1a\xffffff8b] fw_state=0x00000008 [ 21.614585] RTL871X: indicate disassoc [ 21.908495] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [ 25.006282] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS [ 26.247997] RTL871X: nolinked power save enter As you can see some of these line are related to the RTL871X that is my USB wireless adapter, but I don't know is that these line report an error or if it is all ok. Looking at the adapter status I obtain: pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff As you can see the mode is DORMANT but I think that this is normal because now I am connected using ethernet. I tryied to set up the adapter but it seems that I obtain no result, infact: pi@raspberrypi ~ $ sudo ip link set dev wlan0 up pi@raspberrypi ~ $ ip link list dev wlan0 3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DORMANT qlen 1000 link/ether e8:94:f6:19:80:4c brd ff:ff:ff:ff:ff:ff pi@raspberrypi ~ $ sudo ip link set dev wlan0 up This is my /etc/network/interfaces file content and it is ok: auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp and it is the /etc/wpa_supplicant/wpa_supplicant.conf that I think is ok (I did not change it compared to when it worked): ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev update_config=1 network={ ssid="MY-NETWORK" psk="mypassword" key_mgmt=WPA-PSK } and infact if I execute a network scan I correctly find MY-NETWORK in the network list,infact: pi@raspberrypi ~ $ sudo iwlist wlan0 scan | grep ESSID ESSID:"TeleTu_74888B0060AD" ESSID:"MY-NETWORK" ESSID:"FASTWEB-1-PT6NtjL4TOSe" ESSID:"DC" So I reboot the system and I remove the ethernet cable but when I try to connect again to my raspberry I obatin the following error message: andrea@andrea-virtual-machine:~$ sudo ssh [email protected] ssh: connect to host 192.168.1.9 port 22: No route to host It seems that it can't connect using wireless. What could be the problem? What am I missing? How can I solve this situation? Tnx

  Read the article

• CentOS 6.2 Bridge Setup for KVM

  - by Gaia

  I'm trying to set up bridged networking with KVM on CentOS 6.2 to no avail. There are plenty of docs and tutorials about it, but they all seem to conflict or don't provide info specific enough to my situation. I just don't get it. I access the host via public IP "xxx.xxx.128.58". All other available IPs (/29) should be bridged and made available to the only KVM guest (running a public facing LAMP stack) that will be setup on this machine. The amazingly unhelpful NOC people assigned the extra IPs to eth1. Is this correct? Should br0 bridge to eth0 or eth1? How do I set this up? Here is the relevant info: eth0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BC inet6 addr: fe80::225:90ff:fe68:febc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:763 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:550811 (537.9 KiB) TX bytes:648 (648.0 b) Memory:fb980000-fba00000 eth1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.58 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 inet6 addr: fe80::225:90ff:fe68:febd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1806 errors:0 dropped:0 overruns:0 frame:0 TX packets:1505 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:133166 (130.0 KiB) TX bytes:106070 (103.5 KiB) Memory:fb900000-fb980000 eth1:0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.59 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.60 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:2 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.61 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:3 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.62 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) virbr0 Link encap:Ethernet HWaddr 52:54:00:62:55:68 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=XXXX.domain.com > brctl show bridge name bridge id STP enabled interfaces br0 8000.00259068febc no eth0 virbr0 8000.525400625568 yes virbr0-nic > ls -fl | grep ifcfg -rw-r--r-- 1 root root 198 Jun 7 10:58 ifcfg-eth0 -rw-r--r--. 1 root root 254 Oct 7 2011 ifcfg-lo -rw-r--r-- 1 root root 77 Jun 6 18:51 ifcfg-eth1-range0 -rw-r--r-- 1 root root 168 Jun 6 18:50 ifcfg-eth1 > cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO="static" BRIDGE="br0" HWADDR="00:25:90:68:FE:BC" IPV6INIT="yes" MTU="1500" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" IPADDR="yyy.yyy.216.131" NETMASK="255.255.255.128" > cat ifcfg-eth1 DEVICE="eth1" HWADDR="00:25:90:68:FE:BD" NM_CONTROLLED="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="xxx.xxx.128.58" NETMASK="255.255.255.248" GATEWAY="xxx.xxx.128.57" > cat ifcfg-eth1-range0 IPADDR_START="xxx.xxx.128.59" IPADDR_END="xxx.xxx.128.62" CLONENUM_START="0" Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xxx.xxx.128.56 * 255.255.255.248 U 0 0 0 eth1 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0 link-local * 255.255.0.0 U 1003 0 0 eth1 default xxx.xxx.128.57 0.0.0.0 UG 0 0 0 eth1

  Read the article

• What's the best practice for linking to/from guest posts on other blogs?

  - by sam

  When writing a guest blog for a site, I include a link back to my site - an inbound link. If I were to write a post on my blog publicising my guest post, that would mean there were reciprocal links, thus cancelling each other out, correct? If I made the link (on my blog) back to the guest post nofollow, would that cancel the effect, meaning I still get link juice from the guest post? Further down the line if the site I posted on as a guest wanted to write a post for my site, what is the best way for me to prevent re-introducing the reciprocal link problem?

  Read the article

• Tracking click conversions with Google Analytics

  - by Joel

  Is there anyway I can use Google Analytics to track click conversions on a link? For example, if I have a link to www.a.com , is it possible for google to track the number of times that particular link was shown on my page and then track how many times it was really clicked? The problem is that I do not show the link to www.a.com every time the page loads. I am using a random function (server side) to generate a different link everytime. I would like Google Analytics to provide me with the click conversion for each of the links I choose to show the user. Thanks, Joel

  Read the article

• Share links with <script src=""> SEO

  - by gansbrest

  Hi, I would like to create a share link to my website using javascript: script src="[url-to-my-script]" Basically the main idea behind this is to render HTML block with an image and link to the website. By using JavaScript approach I can control the look and feel of that link + potentially I could change the link html in the future without touching partner websites. The only potential problem I see with this approach is SEO. I'm not sure if google will be able to index that link to my website, since it's generated by javascript.

  Read the article

• IPv6 host route is deleted after PMTU expires

  - by SAPikachu

  I am experimenting my new IPv6 tunnel setup between my local Ubuntu box and a scratch Linode. I set up some docker containers, configured 6in4 tunnel server and IPv6 forwarding on the Linode: # uname -a Linux argo 3.15.4-x86_64-linode45 #1 SMP Mon Jul 7 08:42:36 EDT 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 48: sit-sapikachu: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1472 qdisc noqueue state UNKNOWN group default link/sit 106.185.41.115 peer 1.2.3.4 inet6 fd00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::6ab9:2973/64 scope link valid_lft forever preferred_lft forever 13: docker0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default link/ether 56:84:7a:fe:97:99 brd ff:ff:ff:ff:ff:ff inet 172.17.42.1/16 scope global docker0 valid_lft forever preferred_lft forever inet6 fc00::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::5484:7aff:fefe:9799/64 scope link valid_lft forever preferred_lft forever // Docker containers are bridged to docker0 On my local box, I configured a 6in4 tunnel interface to connect to the Linode box, and added a host route to one of the docker container: # uname -a Linux sapikachu-netbox 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # ip addr .. snipped .. 16: sit-argo: <POINTOPOINT,NOARP,UP,LOWER_UP> mtu 1480 qdisc noqueue state UNKNOWN group default link/sit 0.0.0.0 peer 106.185.41.115 inet6 fd00::2/64 scope global valid_lft forever preferred_lft forever inet6 fe80::a97:302/64 scope link valid_lft forever preferred_lft forever inet6 fe80::ac19:1/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1f0/64 scope link valid_lft forever preferred_lft forever inet6 fe80::c0a8:1fa/64 scope link valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether *** brd ff:ff:ff:ff:ff:ff .. snipped .. inet6 fd00:0:1::1/64 scope global valid_lft forever preferred_lft forever inet6 fe80::2e0:6fff:fe0e:365e/64 scope link valid_lft forever preferred_lft forever # ip route replace fc00::1875:8606:d8c1:8a9d via fd00::1 # Add route to docker container # ip -6 route .. snipped unrelated routes fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires 590sec mtu 1472 fd00::/64 dev sit-argo proto kernel metric 256 fd00:0:1::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sit-argo proto kernel metric 256 (Note that tunnel MTU on my local box is different from the server, this is intentional for testing) After adding the host route to the docker container (fc00::1875:8606:d8c1:8a9d), I can ping the container without problem until the route expires. After that I couldn't get reply any more. If I run ip -6 route in a few seconds after expiration, expiration time of the host route will be a negative number: fc00::1875:8606:d8c1:8a9d via fd00::1 dev sit-argo metric 1024 expires -1sec And output of ip route get fc00::1875:8606:d8c1:8a9d shows that it is routed to my default IPv6 gateway (which fails to route it correctly of course, since the address is not globally routable). After some time, the host route disappears without a trace. This problem won't happen if I do either one of the following things: Set MTU of tunnel on my local box to be the same as the server (1472). The route won't have expiration time in both ip -6 route and ip route get in this case. Instead of adding a host route, add a route with network mask (even /127 works). In this case ip -6 route shows the route without expiration time, ip route get shows expiration time but it will be correctly refreshed after expiration. Although this problem can be easily resolved, I am curious to know why this happens. Is there error in my configuration, or is this a kernel bug?

  Read the article

• How broken is routing strategy that causes a martian packet (so far only) during tracepath?

  - by lkraav

  I believe I've achieved a table that routes packets from and to eth1/192.168.3.x through 192.168.3.1, and packets from and to eth0/192.168.1.x through 192.168.1.1 (helpful source). Question: when doing tracepath from 192.168.3.20 (from within vserver), I'm getting kernel: [318535.927489] martian source 192.168.3.20 from 212.47.223.33, on dev eth0 at or near the target IP, while intermediary hops go without (log below). I don't understand why this packet is arriving on eth0, instead of eth1, even after reading this: Note that you may see packets from non-routable IP addresses when running the traceroute or tracepath commands. While packets cannot be routed to these routers, packets sent between 2 routers only need to know the address of the next hop within the local networks, which could be a non-routable address. Can someone explain that paragraph in human language? Based on short initial trials so far, everything else seems to work without causing martians. Is this contained to the nature of tracepath operation or do I have some other bigger routing problem that will cause work traffic breakage? Side note: is it possible to inspect martian packet with tcpdump or wireshark or anything of the sort? I'm have not been able to get it to show up on my own. vserver-20 / # tracepath -n 212.47.223.33 1: 192.168.3.2 0.064ms pmtu 1500 1: 192.168.3.1 1.076ms 1: 192.168.3.1 1.259ms 2: 90.191.8.2 1.908ms 3: 90.190.134.194 2.595ms 4: 194.126.123.94 2.136ms asymm 5 5: 195.250.170.22 2.266ms asymm 6 6: 212.47.201.86 2.390ms asymm 7 7: no reply 8: no reply 9: no reply ^C Host routing: $ sudo ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo 2: sit0: <NOARP> mtu 1480 qdisc noop state DOWN link/sit 0.0.0.0 brd 0.0.0.0 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:24:1d:de:b3:5d brd ff:ff:ff:ff:ff:ff inet 192.168.1.2/24 scope global eth0 4: eth1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:0c:46:46:a3:6a brd ff:ff:ff:ff:ff:ff inet 192.168.3.2/27 scope global eth1 inet 192.168.3.20/27 brd 192.168.3.31 scope global secondary eth1 # linux-vserver instance $ sudo ip route default via 192.168.1.1 dev eth0 metric 3 unreachable 127.0.0.0/8 scope host 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.2 192.168.3.0/27 dev eth1 proto kernel scope link src 192.168.3.2 $ sudo ip rule 0: from all lookup local 32764: from all to 192.168.3.0/27 lookup dmz 32765: from 192.168.3.0/27 lookup dmz 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table dmz default via 192.168.3.1 dev eth1 metric 4 192.168.3.0/27 dev eth1 scope link metric 4 Gateway routing # ip route 10.24.0.2 dev tun0 proto kernel scope link src 10.24.0.1 10.24.0.0/24 via 10.24.0.2 dev tun0 192.168.3.0/24 dev br-dmz proto kernel scope link src 192.168.3.1 192.168.1.0/24 dev br-lan proto kernel scope link src 192.168.1.1 $ISP_NET/23 dev eth0.1 proto kernel scope link src $WAN_IP default via $ISP_GW dev eth0.1 Additional background Options for non-virtualized network interface isolation?

  Read the article

• Why facelets ignore href-attribute of a link when I use <a href="url" jsfc="h:outputLink"> ?

  - by Roman

  I have next facelet composition: <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xmlns:ui="http://java.sun.com/jsf/facelets" xmlns:h="http://java.sun.com/jsf/html" xmlns:f="http://java.sun.com/jsf/core"> <body> <ui:composition> <ul id="navigation"> <li> <a href="http://google.com" id="google1" jsfc="h:outputLink">google.com</a> </li> <li> <h:outputLink id="google2" value="http://google.com"> <h:outputText id="outputtext" value="google.com"/> </h:outputLink> </li> </ul> </ui:composition> </body> </html> There must be a mistake because what I expected to see is almost the same final html-markup. But actually here is what facelets generated: <ul id="navigation"> <li><a id="google1" name="google1" href="">google.com</a></li> <li><a id="google2" name="google2" href="http://google.com"><span id="outputtext">google.com</span></a> </li> </ul> Why it ignored href attribute of the first link? What is the correct way to do what I'm trying to do? One more additional question: if I'm using jsfc everywhere I can then what should I do with components from f: namespace? Where should be <f:view> placed? Maybe in the template.xhtml? Or I should simply ignore it?

  Read the article

• How to use Crtl in a Delphi unit in a C++Builder project? (or link to C++Builder C runtime library)

  - by Craig Peterson

  I have a Delphi unit that is statically linking a C .obj file using the {$L xxx} directive. The C file is compiled with C++Builder's command line compiler. To satisfy the C file's runtime library dependencies (_assert, memmove, etc), I'm including the crtl unit Allen Bauer mentioned here. unit FooWrapper; interface implementation uses Crtl; // Part of the Delphi RTL {$L FooLib.obj} // Compiled with "bcc32 -q -c foolib.c" procedure Foo; cdecl; external; end. If I compile that unit in a Delphi project (.dproj) everthing works correctly. If I compile that unit in a C++Builder project (.cbproj) it fails with the error: [ILINK32 Error] Fatal: Unable to open file 'CRTL.OBJ' And indeed, there isn't a crtl.obj file in the RAD Studio install folder. There is a .dcu, but no .pas. Trying to add crtdbg to the uses clause (the C header where _assert is defined) gives an error that it can't find crtdbg.dcu. If I remove the uses clause, it instead fails with errors that __assert and _memmove aren't found. So, in a Delphi unit in a C++Builder project, how can I export functions from the C runtime library so they're available for linking? I'm already aware of Rudy Velthuis's article. I'd like to avoid manually writing Delphi wrappers if possible, since I don't need them in Delphi, and C++Builder must already include the necessary functions. Edit For anyone who wants to play along at home, the code is available in Abbrevia's Subversion repository at https://tpabbrevia.svn.sourceforge.net/svnroot/tpabbrevia/trunk. I've taken David Heffernan's advice and added a "AbCrtl.pas" unit that mimics crtl.dcu when compiled in C++Builder. That got the PPMd support working, but the Lzma and WavPack libraries both fail with link errors: [ILINK32 Error] Error: Unresolved external '_beginthreadex' referenced from ABLZMA.OBJ [ILINK32 Error] Error: Unresolved external 'sprintf' referenced from ABWAVPACK.OBJ [ILINK32 Error] Error: Unresolved external 'strncmp' referenced from ABWAVPACK.OBJ [ILINK32 Error] Error: Unresolved external '_ftol' referenced from ABWAVPACK.OBJ AFAICT, all of them are declared correctly, and the _beginthreadex one is actually declared in AbLzma.pas, so it's used by the pure Delphi compile as well. To see it yourself, just download the trunk (or just the "source" and "packages" directories), disable the {$IFDEF BCB} block at the bottom of AbDefine.inc, and try to compile the C++Builder "Abbrevia.cbproj" project.

  Read the article

• convert remote object result to array collection in flex...........

  - by user364199

  HI guys, im using zend_amf and flex. My problem is i have to populate my advance datagrid using array collection. this array collection have a children. example: [Bindable] private var dpHierarchy:ArrayCollection = new ArrayCollection([ {trucks:"Truck", children: [ {trucks:"AMC841", total_trip:1, start_time:'3:46:40 AM'}, {trucks:"AMC841", total_trip:1, start_time:'3:46:40 AM'}]) ]}; but the datasource of my datagrid should come from a database, how can i convert the result from remote object to array collection that has the same format like in my example, or any other way. here is my advance datagrid <mx:AdvancedDataGrid id="datagrid" width="500" height="200" lockedColumnCount="1" lockedRowCount="0" horizontalScrollPolicy="on" includeIn="loggedIn" x="67" y="131"> <mx:dataProvider> <mx:HierarchicalData id="dpHierarchytest" source="{dp}"/> </mx:dataProvider> <mx:groupedColumns> <mx:AdvancedDataGridColumn dataField="trucks" headerText="Trucks"/> <mx:AdvancedDataGridColumn dataField="total_trip" headerText="Total Trip"/> <mx:AdvancedDataGridColumnGroup headerText="PRECOOLING"> <mx:AdvancedDataGridColumnGroup headerText="Before Loading"> <mx:AdvancedDataGridColumn dataField="start_time" headerText="Start Time"/> <mx:AdvancedDataGridColumn dataField="end_time" headerText="End Time"/> <mx:AdvancedDataGridColumn dataField="precooling_time" headerText="Precooling Time"/> <mx:AdvancedDataGridColumn dataField="precooling_temp" headerText="Precooling Temp"/> </mx:AdvancedDataGridColumnGroup> <mx:AdvancedDataGridColumnGroup headerText="Before Dispatch"> <mx:AdvancedDataGridColumn dataField="bd_start_time" headerText="Start Time"/> <mx:AdvancedDataGridColumn dataField="bd_end_time" headerText="End Time"/> <mx:AdvancedDataGridColumn dataField="bd_precooling_time" headerText="Precooling Time"/> <mx:AdvancedDataGridColumn dataField="bd_precooling_temp" headerText="Precooling Temp"/> </mx:AdvancedDataGridColumnGroup> <mx:AdvancedDataGridColumn dataField="remarks" headerText="Remarks"/> </mx:AdvancedDataGridColumnGroup> <mx:AdvancedDataGridColumnGroup headerText="Temperature Compliance"> <mx:AdvancedDataGridColumn dataField="total_hit" headerText="Total Hit"/> <mx:AdvancedDataGridColumn dataField="total_miss" headerText="Total Miss"/> <mx:AdvancedDataGridColumn dataField="cold_chain_compliance" headerText="Cold Chain Compliance"/> <mx:AdvancedDataGridColumn dataField="average_temp" headerText="Average Temp"/> </mx:AdvancedDataGridColumnGroup> <mx:AdvancedDataGridColumnGroup headerText="Productivity"> <mx:AdvancedDataGridColumn dataField="total_drop_points" headerText="Total Drop Points"/> <mx:AdvancedDataGridColumn dataField="total_delivery_time" headerText="Total Delivery Time"/> <mx:AdvancedDataGridColumn dataField="total_distance" headerText="Total Distance"/> </mx:AdvancedDataGridColumnGroup> <mx:AdvancedDataGridColumnGroup headerText="Trip Exceptions"> <mx:AdvancedDataGridColumn dataField="total_doc" headerText="Total DOC"/> <mx:AdvancedDataGridColumn dataField="total_eng" headerText="Total ENG"/> <mx:AdvancedDataGridColumn dataField="total_fenv" headerText="Total FENV"/> <mx:AdvancedDataGridColumn dataField="average_speed" headerText="Average Speed"/> </mx:AdvancedDataGridColumnGroup> </mx:groupedColumns> </mx:AdvancedDataGrid> Thanks, and i really need some help.

  Read the article

• Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host

  - by xnoor

  i have an update server that sends client updates through TCP port 12000, the sending of a single file is successful only the first time, but after that i get an error message on the server "Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host", if i restart the update service on the server, it works again only one, i have normal multithreaded windows service SERVER CODE namespace WSTSAU { public partial class ApplicationUpdater : ServiceBase { private Logger logger = LogManager.GetCurrentClassLogger(); private int _listeningPort; private int _ApplicationReceivingPort; private string _setupFilename; private string _startupPath; public ApplicationUpdater() { InitializeComponent(); } protected override void OnStart(string[] args) { init(); logger.Info("after init"); Thread ListnerThread = new Thread(new ThreadStart(StartListener)); ListnerThread.IsBackground = true; ListnerThread.Start(); logger.Info("after thread start"); } private void init() { _listeningPort = Convert.ToInt16(ConfigurationSettings.AppSettings["ListeningPort"]); _setupFilename = ConfigurationSettings.AppSettings["SetupFilename"]; _startupPath = System.IO.Path.GetDirectoryName(System.Reflection.Assembly.GetExecutingAssembly().GetName().CodeBase).Substring(6); } private void StartListener() { try { logger.Info("Listening Started"); ThreadPool.SetMinThreads(50, 50); TcpListener listener = new TcpListener(_listeningPort); listener.Start(); while (true) { TcpClient c = listener.AcceptTcpClient(); ThreadPool.QueueUserWorkItem(ProcessReceivedMessage, c); } } catch (Exception ex) { logger.Error(ex.Message); } } void ProcessReceivedMessage(object c) { try { TcpClient tcpClient = c as TcpClient; NetworkStream Networkstream = tcpClient.GetStream(); byte[] _data = new byte[1024]; int _bytesRead = 0; _bytesRead = Networkstream.Read(_data, 0, _data.Length); MessageContainer messageContainer = new MessageContainer(); messageContainer = SerializationManager.XmlFormatterByteArrayToObject(_data, messageContainer) as MessageContainer; switch (messageContainer.messageType) { case MessageType.ApplicationUpdateMessage: ApplicationUpdateMessage appUpdateMessage = new ApplicationUpdateMessage(); appUpdateMessage = SerializationManager.XmlFormatterByteArrayToObject(messageContainer.messageContnet, appUpdateMessage) as ApplicationUpdateMessage; Func<ApplicationUpdateMessage, bool> HandleUpdateRequestMethod = HandleUpdateRequest; IAsyncResult cookie = HandleUpdateRequestMethod.BeginInvoke(appUpdateMessage, null, null); bool WorkerThread = HandleUpdateRequestMethod.EndInvoke(cookie); break; } } catch (Exception ex) { logger.Error(ex.Message); } } private bool HandleUpdateRequest(ApplicationUpdateMessage appUpdateMessage) { try { TcpClient tcpClient = new TcpClient(); NetworkStream networkStream; FileStream fileStream = null; tcpClient.Connect(appUpdateMessage.receiverIpAddress, appUpdateMessage.receiverPortNumber); networkStream = tcpClient.GetStream(); fileStream = new FileStream(_startupPath + "\\" + _setupFilename, FileMode.Open, FileAccess.Read); FileInfo fi = new FileInfo(_startupPath + "\\" + _setupFilename); BinaryReader binFile = new BinaryReader(fileStream); FileUpdateMessage fileUpdateMessage = new FileUpdateMessage(); fileUpdateMessage.fileName = fi.Name; fileUpdateMessage.fileSize = fi.Length; MessageContainer messageContainer = new MessageContainer(); messageContainer.messageType = MessageType.FileProperties; messageContainer.messageContnet = SerializationManager.XmlFormatterObjectToByteArray(fileUpdateMessage); byte[] messageByte = SerializationManager.XmlFormatterObjectToByteArray(messageContainer); networkStream.Write(messageByte, 0, messageByte.Length); int bytesSize = 0; byte[] downBuffer = new byte[2048]; while ((bytesSize = fileStream.Read(downBuffer, 0, downBuffer.Length)) > 0) { networkStream.Write(downBuffer, 0, bytesSize); } fileStream.Close(); tcpClient.Close(); networkStream.Close(); return true; } catch (Exception ex) { logger.Info(ex.Message); return false; } finally { } } protected override void OnStop() { } } i have to note something that my windows service (server) is multithreaded.. i hope anyone can help with this

  Read the article

• How can I link two Java serialised objects back together?

  - by Kidburla

  Sometimes (quite a lot, actually) we get a situation in Java where two objects are pointing to the same thing. Now if we serialise these separately it is quite appropriate that the serialised forms have separate copies of the object as it should be possible to open one without the other. However if we now deserialise them both, we find that they are still separated. Is there any way to link them back together? Example follows. public class Example { private static class ContainerClass implements java.io.Serializable { private ReferencedClass obj; public ReferencedClass get() { return obj; } public void set(ReferencedClass obj) { this.obj = obj; } } private static class ReferencedClass implements java.io.Serializable { private int i = 0; public int get() { return i; } public void set(int i) { this.i = i; } } public static void main(String[] args) throws Exception { //Initialise the classes ContainerClass test1 = new ContainerClass(); ContainerClass test2 = new ContainerClass(); ReferencedClass ref = new ReferencedClass(); //Make both container class point to the same reference test1.set(ref); test2.set(ref); //This does what we expect: setting the integer in one (way of accessing the) referenced class sets it in the other one test1.get().set(1234); System.out.println(Integer.toString(test2.get().get())); //Now serialise the container classes java.io.ObjectOutputStream os = new java.io.ObjectOutputStream(new java.io.FileOutputStream("C:\\Users\\Public\\test1.ser")); os.writeObject(test1); os.close(); os = new java.io.ObjectOutputStream(new java.io.FileOutputStream("C:\\Users\\Public\\test2.ser")); os.writeObject(test2); os.close(); //And deserialise them java.io.ObjectInputStream is = new java.io.ObjectInputStream(new java.io.FileInputStream("C:\\Users\\Public\\test1.ser")); ContainerClass test3 = (ContainerClass)is.readObject(); is.close(); is = new java.io.ObjectInputStream(new java.io.FileInputStream("C:\\Users\\Public\\test2.ser")); ContainerClass test4 = (ContainerClass)is.readObject(); is.close(); //We expect the same thing as before, and would expect a result of 4321, but this doesn't happen as the referenced objects are now separate instances test3.get().set(4321); System.out.println(Integer.toString(test4.get().get())); } }

  Read the article

• Help with a simple switch statement

  - by revive

  I need to find the value of a variable and use it to add a class to a div, based on a switch statement. For example, my variable is $link and if $link has google.com IN IT at all, I need $class to equal 'google', if $link as yahoo.com IN IT at all, $class then needs to equal 'yahoo' So, I need something like this, but I'm not sure how/or if to use preg_match or something to check and see if the $link variable has the value we are looking for in it - see 'case' text below: switch ($link) { case 'IF link has Google.com in it': $class = 'google'; break; case 'IF link has Yahoo.com in it': $class = 'yahoo'; break; default: # code... break; } OR if there is a better way to do this, please let me know :D Thanks

  Read the article

• Show list items specific to user sharepoint

  - by Sachin

  Hi all, In my project i have a asset list which contains "request to download" link. In the same list there is "download link" column which is default empty. Now when any user clicks on request to download link a workflow is activated and it will send request to approver to approve or reject the download request. If approver accept the request then the "download link" column in the asset list will be updated by some URL which redirect user to download page. Now what happen is, if user A send request to download asset to approver and approver approves it this will update respective item in asset list and put a download URL in "Download Link" column but if user B get look for the same record in asset list the download link will be visible to this user too which is wrong. I want to display download link columns value to only those user whos request has been approve. FYI: I am using WSS 3.0 Can anyone help me what should be the best approch to do this...? Thanks in Advance Sachin

  Read the article

• ASP.NET MVC DataAnnotations different tables. Can it be done?

  - by mazhar kaunain baig

  i have a language table which is as a foreign key in the link table , The link can be in 3 languages meaning there will be 3 rows in the link table every time i enter the record . i am using jQuery tabs to enter the records in 3 languages . OK so that thing is that there will be three text boxes for every field in the table.link name field will have 3 text boxes, description will have 3 text boxes and so on. i am using LINK to SQL with VS2010. i will be creating link class with MetadataType so how will i handle for eg link name attribute 3 times

  Read the article

• Sync Your Pidgin Profile Across Multiple PCs with Dropbox

  - by Matthew Guay

  Pidgin is definitely our favorite universal chat client, but adding all of your chat accounts to multiple computers can be frustrating.  Here’s how you can easily transfer your Pidgin settings to other computers and keep them in sync using Dropbox. Getting Started Make sure you have both Pidgin and Dropbox installed on any computers you want to sync.  To sync Pidgin, you need to: Move your Pidgin profile folder on your first computer to Dropbox Create a symbolic link from the new folder in Dropbox to your old profile location Delete the default pidgin profile on your other computer, and create a symbolic link from your Dropbox Pidgin profile to the default Pidgin profile location This sounds difficult, but it’s actually easy if you follow these steps.  Here we already had all of our accounts setup in Pidgin in Windows 7, and then synced this profile with an Ubuntu and a XP computer with fresh Pidgin installs.  Our instructions for each OS are based on this, but just swap the sync order if your main Pidgin install is in XP or Ubuntu. Please Note:  Please make sure Pidgin isn’t running on your computer while you are making the changes! Sync Your Pidgin Profile from Windows 7 Here is Pidgin with our accounts already setup.  Our Pidgin profile has a Gtalk, MSN Messenger, and Facebook Chat account, and lots of log files. Let’s move this profile to Dropbox to keep it synced.  Exit Pidgin, and then enter %appdata% in the address bar in Explorer or press Win+R and enter %appdata%.  Select the .purple folder, which is your Pidgin profiles and settings folder, and press Ctrl+X to cut it. Browse to your Dropbox folder, and press Ctrl+V to paste the .purple folder there. Now we need to create the symbolic link.  Enter  “command” in your Start menu search, right-click on the Command Prompt shortcut, and select “Run as administrator”. We can now use the mklink command to create a symbolic link to the .purple folder.  In Command Prompt, enter the following and substitute username for your own username. mklink /D “C:\Users\username\Documents\My Dropbox\.purple” “C:\Users\username\AppData\Roaming\.purple” And that’s it!  You can open Pidgin now to make sure it still works as before, with your files being synced with Dropbox. Please Note:  These instructions work the same for Windows Vista.  Also, if you are syncing settings from another computer to Windows 7, then delete the .purple folder instead of cutting and pasting it, and reverse the order of the file paths when creating the symbolic link. Add your Pidgin Profile to Ubuntu Our Ubuntu computer had a clean install of Pidgin, so we didn’t need any of the information in its settings.  If you’ve run Pidgin, even without creating an account, you will need to first remove its settings folder.  Open your home folder, and click View, and then “Show Hidden Files” to see your settings folders. Select the .purple folder, and delete it. Now, to create the symbolic link, open Terminal and enter the following, substituting username for your username: ln –s /home/username/Dropbox/.purple /home/username/ Open Pidgin, and you will see all of your accounts that were on your other computer.  No usernames or passwords needed; everything is setup and ready to go.  Even your status is synced; we had our status set to Away in Windows 7, and it automatically came up the same in Ubuntu. Please Note: If your primary Pidgin account is in Ubuntu, then cut your .purple folder and paste it into your Dropbox folder instead.  Then, when creating the symbolic link, reverse the order of the folder paths. Add your Pidgin Profile to Windows XP In XP we also had a clean install of Pidgin.  If you’ve run Pidgin, even without creating an account, you will need to first remove its settings folder.  Click Start, the Run, and enter %appdata%. Delete your .purple folder. XP does not include a way to create a symbolic link, so we will use the free Junction tool from Sysinternals.  Download Junction (link below) and unzip the folder. Open Command Prompt (click Start, select All Programs, then Accessories, and select Command Prompt), and enter cd followed by the path of the folder where you saved Junction.   Now, to create the symbolic link, enter the following in Command Prompt, substituting username with your username. junction –d “C:\Documents and Settings\username\Application Data\.purple” “C:\Documents and Settings\username\My Documents\My Dropbox\.purple” Open Pidgin, and you will see all of your settings just as they were on your other computer.  Everything’s ready to go.   Please Note: If your primary Pidgin account is in Windows XP, then cut your .purple folder and paste it into your Dropbox folder instead.  Then, when creating the symbolic link, reverse the order of the folder paths. Conclusion This is a great way to keep all of your chat and IM accounts available from all of your computers.  You can easily access logs from chats you had on your desktop from your laptop, or if you add a chat account on your work computer you can use it seamlessly from your home computer that evening.  Now Pidgin is the universal chat client that is always ready whenever and wherever you need it! Links Downlaod Pidgin Download and signup for Dropbox Download Junction for XP Similar Articles Productive Geek Tips Add "My Dropbox" to Your Windows 7 Start MenuUse Multiple Firefox Profiles at the Same TimeEasily Add Facebook Chat to PidginPut Your Pidgin Buddy List into the Windows Vista SidebarBackup and Restore Firefox Profiles Easily TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Download Free iPad Wallpapers at iPad Decor Get Your Delicious Bookmarks In Firefox’s Awesome Bar Manage Photos Across Different Social Sites With Dropico Test Drive Windows 7 Online Download Wallpapers From National Geographic Site Spyware Blaster v4.3

  Read the article

• 13.10 - Weird WiFi connection problems - WMP300N - Broadcom BCM4321

  - by user1898041

  Just installed 13.10 on my desktop and I really like it. After having problems with getting the wifi to work, I installed it connected to the internet with an ethernet cable and added in the 3rd party software and updates as per the installation procedure. After installation was completed, I saw the wifi icon in the upper right hand corner, but it was not seeing any wifi networks. Some Googling brought me to use the 'Additional Drivers' application. It found the WMP300N Broadcom BDM4321 based pci wifi card and installed the proprietary Broadcom STA wireless driver, which may have been installed before. I'm not sure. Here is the weird part: when I start my system, wifi seems to be in some sort of suspended state where the system sees that the card exists but the card will not detect any wifi networks. It will work after booting once I 'Additional Drivers' application and then start FireFox. I know it seems weird, but this is the process I've got down to get the card to recognize wifi networks. After those applications are open for a few seconds, the card starts to function like normal (although maintaining the wifi connection is problem but most likely a seperate issue). The reason this is a problem is because this is supposed to just be a headless box managed through SSH. Here are the readouts from the common network diagnosis programs BEFORE I open 'Additional Drivers' and 'FireFox'. All commands were done with sudo. lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) - iwconfig eth1 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off - iwlist scan eth1 No scan results - Here are the various commands AFTER I open 'Additional Drivers' and 'FireFox' lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.103 latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:85 errors:0 dropped:0 overruns:0 frame:11901 TX packets:132 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52641 (52.6 KB) TX bytes:19058 (19.0 KB) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6084 (6.0 KB) TX bytes:6084 (6.0 KB) - iwconfig eth1 IEEE 802.11abg ESSID:"BU" Mode:Managed Frequency:2.447 GHz Access Point: 00:26:F2:1F:81:02 Bit Rate=54 Mb/s Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=59/70 Signal level=-51 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - iwlist scan A LOT OF SSIDs FOUND! - I'd like to have this problem fixed, but I'm not quite sure where to go. Been Googling a lot and can't seem to find anyone else with this problem.

  Read the article

• Intel Corporation Ethernet Connection does not start properly

  - by Oscar Alejos

  I'm experiencing some problems when trying to connect my PC to the router through a switch. When the PC is directly connected to the router, everything works fine, Ubuntu (14.04) starts normally, and the Internet connection runs inmediately. The Ethernet controller is the Intel Corporation Ethernet Connection, as lspci returns: $ lspci | grep Eth 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) However, when I try to connect through the switch what I get is the following. dmesg returns: $ dmesg | grep eth [ 1.035585] e1000e 0000:00:19.0 eth0: registered PHC clock [ 1.035587] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a7:be:5d [ 1.035589] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.035625] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF [ 1.357838] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.165413] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.165574] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.641287] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.715086] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [ 16.715090] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO [ 16.715117] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready It looks like eth0 is properly working. Actually, nm-tool returns: $ nm-tool - Device: eth0 [Conexión cableada] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: 00:22:4D:A7:BE:5D Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.30 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 80.58.61.250 DNS: 80.58.61.254 DNS: 192.168.1.1 However, ping returns: $ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. From 192.168.1.30 icmp_seq=1 Destination Host Unreachable From 192.168.1.30 icmp_seq=2 Destination Host Unreachable From 192.168.1.30 icmp_seq=3 Destination Host Unreachable The connection is restored by restarting it: # ifconfig eth0 down # ifconfig eth0 up From this point on, everything runs smoothly, as if the PC were directly connected to the router. It seems to be an issue related to the integrated LAN adaptor and the Ethernet controller, since my laptop connects without any problem. My desktop board is an Intel DB85FL. I'd be grateful if anyone could give some ideas on how to solve this issue. Thank you in advance.

  Read the article

• mint linux, DVD drive keeps randomly being accessed. unsure how to find culprit

  - by juicebox

  I have a workstation with mint linux 12. It seems like the DVD drive on the machine keeps randomly "activating". By activating it makes noise, the light turns on, and it seems like it is checking if a disk is in it. At first I thought I was being hacked and someone/something was trying to check if I had media in the DVDRom drive. I ruled that out with netstat and rkhunter. I checked my logs and the only thing I can find that might help point out the problem are these repeated chunks in syslog: Mar 24 17:47:31 rich-MINT kernel: [ 9846.551422] ata2.00: cmd a0/00:00:00:08:00/00:00:00:00:00/a0 tag 0 pio 16392 in Mar 24 17:47:31 rich-MINT kernel: [ 9846.551424] res 51/40:01:00:00:00/00:00:00:00:00/a0 Emask 0x10 (ATA bus error) Mar 24 17:47:31 rich-MINT kernel: [ 9846.551427] ata2.00: status: { DRDY ERR } Mar 24 17:47:31 rich-MINT kernel: [ 9846.551433] ata2.00: hard resetting link Mar 24 17:47:32 rich-MINT kernel: [ 9846.868012] ata2.01: hard resetting link Mar 24 17:47:32 rich-MINT kernel: [ 9847.344054] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Mar 24 17:47:32 rich-MINT kernel: [ 9847.344067] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 24 17:47:32 rich-MINT kernel: [ 9847.376118] ata2.00: configured for PIO0 Mar 24 17:47:32 rich-MINT kernel: [ 9847.393047] ata2.01: configured for UDMA/133 Mar 24 17:47:32 rich-MINT kernel: [ 9847.397046] ata2: EH complete and again Mar 24 17:55:28 rich-MINT kernel: [10323.633268] sr 1:0:0:0: ioctl_internal_command return code = 8000002 Mar 24 17:55:28 rich-MINT kernel: [10323.633270] : Sense Key : Aborted Command [current] [descriptor] Mar 24 17:55:28 rich-MINT kernel: [10323.633275] : Add. Sense: No additional sense information Mar 24 17:55:11 rich-MINT kernel: [10306.640009] ata2.00: link is slow to respond, please be patient (ready=0) Mar 24 17:55:16 rich-MINT kernel: [10310.840009] ata2.00: SRST failed (errno=-16) Mar 24 17:55:16 rich-MINT kernel: [10310.840016] ata2.00: hard resetting link Mar 24 17:55:16 rich-MINT kernel: [10311.160013] ata2.01: hard resetting link Mar 24 17:55:16 rich-MINT kernel: [10311.636061] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Mar 24 17:55:16 rich-MINT kernel: [10311.636075] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 24 17:55:16 rich-MINT kernel: [10311.668122] ata2.00: configured for PIO0 Mar 24 17:55:16 rich-MINT kernel: [10311.684854] ata2.01: configured for UDMA/133 Mar 24 17:55:17 rich-MINT kernel: [10312.105473] ata2: EH complete (Copied from Pastebin - http://pastebin.com/YNDrnyzH) If any linux masters could take a quick look at these log outputs and help me understand what is going on , much appreciated.

  Read the article

• Useful SVN and Git commands – Cheatsheet

  - by Madhan ayyasamy

  The following snippets will helpful one who user version control systems like Git and SVN.svn checkout/co checkout-url – used to pull an SVN tree from the server.svn update/up – Used to update the local copy with the changes made in the repository.svn commit/ci – m “message” filename – Used to commit the changes in a file to repository with a message.svn diff filename – shows up the differences between your current file and what’s there now in the repository.svn revert filename – To overwrite local file with the one in the repository.svn add filename – For adding a file into repository, you should commit your changes then only it will reflect in repository.svn delete filename – For deleting a file from repository, you should commit your changes then only it will reflect in repository.svn move source destination – moves a file from one directory to another or renames a file. It will effect your local copy immediately as well as on the repository after committing.git config – Sets configuration values for your user name, email, file formats and more.git init – Initializes a git repository – creates the initial ‘.git’ directory in a new or in an existing project.git clone – Makes a Git repository copy from a remote source. Also adds the original location as a remote so you can fetch from it again and push to it if you have permissions.git add – Adds files changes in your working directory to your index.git rm – Removes files from your index and your working directory so they will not be tracked.git commit – Takes all of the changes written in the index, creates a new commit object pointing to it and sets the branch to point to that new commit.git status – Shows you the status of files in the index versus the working directory.git branch – Lists existing branches, including remote branches if ‘-a’ is provided. Creates a new branch if a branch name is provided.git checkout – Checks out a different branch – switches branches by updating the index, working tree, and HEAD to reflect the chosen branch.git merge – Merges one or more branches into your current branch and automatically creates a new commit if there are no conflicts.git reset – Resets your index and working directory to the state of your last commit.git tag – Tags a specific commit with a simple, human readable handle that never moves.git pull – Fetches the files from the remote repository and merges it with your local one.git push – Pushes all the modified local objects to the remote repository and advances its branches.git remote – Shows all the remote versions of your repository.git log – Shows a listing of commits on a branch including the corresponding details.git show – Shows information about a git object.git diff – Generates patch files or statistics of differences between paths or files in your git repository, or your index or your working directory.gitk – Graphical Tcl/Tk based interface to a local Git repository.

  Read the article

• USB Hub and Ubuntu

  - by aserwin

  I have a powered 7 port hub connected to my Ubuntu box and it does nothing. The devices (zip drive and web cam) work direct, but aren't recognized through the hub. This worked fine in Windows 7. I can't prove it is the OS because this is a new motherboard and processor. Any advice? EDIT : Output from lsusb -v Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:12.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0503 highspeed power enable connect Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:13.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ehci_hcd iProduct 2 EHCI Host Controller iSerial 1 0000:00:16.2 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x000a No power switching (usb 1.0) Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0001 Self Powered Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:12.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:13.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 5 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Port 5: 0000.0100 power Device Status: 0x0001 Self Powered Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:14.5 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 2 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Device Status: 0x0001 Self Powered Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:16.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 2 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0303 lowspeed power enable connect Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0001 Self Powered Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:02:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 2 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Device Status: 0x0001 Self Powered Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 3.02 iManufacturer 3 Linux 3.2.0-32-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:02:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 31 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 bMaxBurst 0 Hub Descriptor: bLength 12 bDescriptorType 42 nNbrPorts 2 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere bHubDecLat 0.0 micro seconds wHubDelay 0 nano seconds DeviceRemovable 0x00 Hub Port Status: Port 1: 0000.02a0 5Gbps power Rx.Detect Port 2: 0000.02a0 5Gbps power Rx.Detect Binary Object Store Descriptor: bLength 5 bDescriptorType 15 wTotalLength 15 bNumDeviceCaps 1 SuperSpeed USB Device Capability: bLength 10 bDescriptorType 16 bDevCapabilityType 3 bmAttributes 0x00 Latency Tolerance Messages (LTM) Supported wSpeedsSupported 0x0008 Device can operate at SuperSpeed (5Gbps) bFunctionalitySupport 3 Lowest fully-functional device speed is SuperSpeed (5Gbps) bU1DevExitLat 3 micro seconds bU2DevExitLat 2047 micro seconds Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 04a9:1709 Canon, Inc. PIXMA MP150 Scanner Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x04a9 Canon, Inc. idProduct 0x1709 PIXMA MP150 Scanner bcdDevice 1.08 iManufacturer 1 Canon iProduct 2 MP150 iSerial 3 20BC24 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 62 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 255 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 11 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 7 Printer bInterfaceSubClass 1 Printer bInterfaceProtocol 2 Bidirectional iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 007 Device 002: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc517 LX710 Cordless Desktop Laser bcdDevice 38.10 iManufacturer 1 Logitech iProduct 2 USB Receiver iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 59 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 98mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 1 Keyboard iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 59 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 177 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) This is with the powered hub plugged in.

  Read the article

• Windows explorer doesn't open My Documents, Music or anything when clicking the library?

  - by Link

  I recently installed Windows 7, and for some reason my Libraries don't open to My Documents, Music and so on.. I can access my files by typing into the explorers address bar, but clicking anything doesn't do anything, it just stays on the same screen. What's wrong? Since this is occurring on a relatively new install, I currently have 259GB free out of 297GB on my HD. The My Documents folder only has about 500 mb of Data.

  Read the article

• Problem libc-so-6-version-glibc-2-14-not-found

  - by alessio

  i have installed nagios core 4 on ubuntu server 12.04 lts.. everything working fine,, but... i have a problem with remote command to a remote linux (ubuntu server 12.04) pc! when i try to check a service, for example: check_swap, check_disk etc.. i got everytime an error: Remote command execution failed: /home/nagios/plugins/check_disk: /lib/x86_64-linux-gnu/libc.so.6: version `GLIBC_2.14' not found (required by /home/nagios/plugins/check_disk) the remote pc is not my pc and i don't want to make a disaster! :) So... how can i fix this problem? any help be appreciate!!! ;) thanks in advance! :)

  Read the article

• Introduction to LinqPad Driver for StreamInsight 2.1

  - by Roman Schindlauer

  We are announcing the availability of the LinqPad driver for StreamInsight 2.1. The purpose of this blog post is to offer a quick introduction into the new features that we added to the StreamInsight LinqPad driver. We’ll show you how to connect to a remote server, how to inspect the entities present of that server, how to compose on top of them and how to manage their lifetime. Installing the driver Info on how to install the driver can be found in an earlier blog post here. Establishing connections As you click on the “Add Connection” link in the left pane you will notice that now it’s possible to build the data context automatically. The new driver appears as an option in the upper list, and if you pick it you will open a connection dialog that lets you connect to a remote StreamInsight server. The connection dialog lets you specify the address of the remote server. You will notice that it’s possible to pick up the binding information from the configuration file of the LinqPad application (which is normally in the same folder as LinqPad.exe and is called LinqPad.exe.config). In order for the context to be generated you need to pick an application from the server. The control is editable hence you can create a new application if you don’t want to make changes to an existing application. If you choose a new application name you will be prompted for confirmation before this gets created. Once you click OK the connection is created and you can start issuing queries against the remote server. If there’s any connectivity error the connection is marked with a red X and you can see the error message informing you what went wrong (i.e., the remote server could not be reached etc.). The context for remote servers Let’s take a look at what happens after we are connected successfully. Every LinqPad query runs inside a context – think of it as a class that wraps all the code that you’re writing. If you’re connecting to a live server the context will contain the following: The application object itself. All entities present in this application (sources, sinks, subjects and processes). The picture below shows a snapshot of the left pane of LinqPad after a successful connection. Every entity on the server has a different icon which will allow users to figure out its purpose. You will also notice that some entities have a string in parentheses following the name. It should be interpreted as such: the first name is the name of the property of the context class and the second name is the name of the entity as it exists on the server. Not all valid entity names are valid identifier names so in cases where we had to make a transformation you see both. Note also that as you hover over the entities you get IntelliSense with their types – more on that later. Remoting is not supported As you play with the entities exposed by the context you will notice that you can’t read and write directly to/from them. If for instance you’re trying to dump the content of an entity you will get an error message telling you that in the current version remoting is not supported. This is because the entity lives on the remote server and dumping its content means reading the events produced by this entity into the local process. ObservableSource.Dump(); Will yield the following error: Reading from a remote 'System.Reactive.Linq.IQbservable`1[System.Int32]' is not supported. Use the 'Microsoft.ComplexEventProcessing.Linq.RemoteProvider.Bind' method to read from the source using a remote observer. This basically tells you that you can call the Bind() method to direct the output of this source to a sink that has to be defined on the remote machine as well. You can’t bring the results to the LinqPad window unless you write code specifically for that. Compose queries You may ask – what's the purpose of all that? After all the same information is present in the EventFlowDebugger, why bother with showing it in LinqPad? First of all, What gets exposed in LinqPad is not what you see in the debugger. In LinqPad we have a property on the context class for every entity that lives on the server. Because LinqPad offers IntelliSense we in fact have much more information about the entity, and more importantly we can compose with that entity very easily. For example, let’s say that this code creates an entity: using (var server = Server.Connect(...)) {     var a = server.CreateApplication("WhiteFish");     var src = a         .DefineObservable<int>(() => Observable.Range(0, 3))         .Deploy("ObservableSource"); If later we want to compose with the source we have to fetch it and then we can bind something to     a.GetObservable<int>("ObservableSource)").Bind(... This means that we had to know a bunch of things about this: that it’s a source, that it’s an observable, it produces a result with payload Int32 and it’s named “ObservableSource”. Only the second and last bits of information are present in the debugger, by the way. As you type in the query window you see that all the entities are present, you get IntelliSense support for them and it’s much easier to make sense of what’s available. Let’s look at a scenario where composition is plausible. With the new programming model it’s possible to create “cold” sources that are parameterized. There was a way to accomplish that even in the previous version by passing parameters to the adapters, but this time it’s much more elegant because the expression declares what parameters are required. Say that we hover the mouse over the ThrottledSource source – we will see that its type is Func<int, int, IQbservable<int>> - this in effect means that we need to pass two int parameters before we can get a source that produces events, and the type for those events is int – in the particular case of my example I had the source produce a range of integers and the two parameters were the start and end of the range. So we see how a developer can create a source that is not running yet. Then someone else (e.g. an administrator) can pass whatever parameters appropriate and run the process. Proxy Types Here’s an interesting scenario – what if someone created a source on a server but they forgot to tell you what type they used. Worse yet, they might have used an anonymous type and even though they can refer to it by name you can’t figure out how to use that type. Let’s walk through an example that shows how you can compose against types you don’t need to have the definition of. This is how we can create a source that returns an anonymous type: Application.DefineObservable(() => Observable.Range(1, 10).Select(i => new { I = i })).Deploy("O1"); Now if we refresh the connection we can see the new source named O1 appear in the list. But what’s more important is that we now have a type to work with. So we can compose a query that refers to the anonymous type. var threshold = new StreamInsightDynamicDriver.TypeProxies.AnonymousType1_0<int>(5); var filter = from i in O1              where i > threshold              select i; filter.Deploy("O2"); You will notice that the anonymous type defined with this statement: new { I = i } can now be manipulated by a client that does not have access to it because the LinqPad driver has generated another type in its stead, named StreamInsightDynamicDriver.TypeProxies.AnonymousType1_0. This type has all the properties and fields of the type defined on the server, except in this case we can instantiate values and use it to compose more queries. It is worth noting that the same thing works for types that are not anonymous – the test is if the LinqPad driver can resolve the type or not. If it’s not possible then a new type will be generated that approximates the type that exists on the server. Control metadata In addition to composing processes on top of the existing entities we can do other useful things. We can delete them – nothing new here as we simply access the entities through the Entities collection of the application class. Here is where having their real name in parentheses comes handy. There’s another way to find out what’s behind a property – dump its expression. The first line in the output tells us what’s the name of the entity used to build this property in the context. Runtime information So let’s create a process to see what happens. We can bind a source to a sink and run the resulting process. If you right click on the connection you can refresh it and see the process present in the list of entities. Then you can drag the process to the query window and see that you can have access to process object in the Processes collection of the application. You can then manipulate the process (delete it, read its diagnostic view etc.). Regards, The StreamInsight Team

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >