Search Results

Search found 7706 results on 309 pages for 'checked'.

Page 204/309 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

  • RAID1: can't replace faulty spare (marked again as 'faulty spare' within seconds)

    - by user212475
    I got a problem that I cannot solve: Our fileserver runs XUbuntu and 3 RAID1s. One has a problem since monday: it consists of sdb and sdc. sdb was marked as faulty by mdadm for unknown reasons. I used --remove to remove it from the RAID and then to add it by --add. All was fine, re-syncing started but never got above 0% and after a few seconds, sdb was again marked as 'faulty spare' (and therefore the RAID degraded, but clean). So I saved the first 512 byte of the old sdb to a file, bought a new HDD of same size (4TB), shut down the computer and replaced sdb physically, switched the computer back on and wrote the 512 byte back to the new drive to have the same partition info as the old drive (both are the same type, from same company). But the new drive shows the same behaviour as the old: I can add, re-syncing starts and after a few seconds its marked as 'faulty spare'. Here exactly what i did: mdadm --remove /dev/md/1 /dev/sdb maadm --detail /dev/md/1 gives me: /dev/md/1: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:56:13 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2424 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 32 1 active sync /dev/sdc mdadm --add /dev/md/1 /dev/sdb mdadm --detail /dev/md/1 gives me: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:57:49 2013 State : clean, degraded, recovering Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Rebuild Status : 0% complete Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2431 Number Major Minor RaidDevice State 2 8 16 0 faulty spare rebuilding /dev/sdb 1 8 32 1 active sync /dev/sdc and after a few seconds: /dev/md/1: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:57:50 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2436 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 32 1 active sync /dev/sdc 2 8 16 - faulty spare /dev/sdb same behaviour if I zero the superblock (mdadm --zero-superblock /dev/sdb) before adding sdb. I do all commands as root and the system holds 3 more 4TB drives, ie the mainboard can handle them. The old harddrive was checked for errors using badblocks, but all is fine. Does anybody have any idea, what the problem is?

    Read the article

  • Desparately Need Help: After a mishap, a folder shows 0 files in it

    - by bobby
    I'm hoping some of you guys may be able to shed some light on this scenario: I had a odt document on which I was working from one of many files in a folder among many on an internal hard-drive. Some kind of glitch occured and the document crashed (this could have been some kind of power charge whilst another hard drive was being unmounted). As I looked into the folders surrounding the folder in which my odt document was stored, they start to show 0 files in them. I immediately switched off the PC and then re-started. Upon the re-start, the folders would show the 1,000s of files I've stored in them and then within 5 minutes, as I started to back them up, freeze, cut-off the process of transfer. When I tried to open anything on the internal hard-drive, be it an avi film, an mp3, a cbr or a word doc, they all showed blank or would work. Some folders had vastly less files showing. Eventually, things calmed down. I closed the PC, checked that the connections were in firmly, gave it a vacuum and restarted the PC. All the files eventually showed up and I started to back them up (which I'd brought a hard drive for anyway but been distracted and not done). All folders show except the one which contained the document I was working on at the time of the trouble. Strangely, it was one that should itself full on several occasions on restarts. It shows zero files now. Properties shows zero files and zero space taken by it. Yet when I drop a file into this folder by pasting it in, it disappears too. Opening the folder, there is nothing there. But if I paste that document again, the PC asks would I like to replace the existing file with the same name (that I can't see), when I click yes, the file appears. When I exit, the folder shows the 0 files in the folder. Going back into the folder, it has disappeared again. I'm hoping that someone can help give me tips to recover the files in the folder, it would be greatly, greatly appreciated. All other films, music, comics, documents show and are fine!

    Read the article

  • Deploying, but without those pesky test files!

    - by Chris Skardon
    Silverlight testing is great, we all know that (don’t we??), we’re expected to do it as part of the development process, but once we’ve got an awesome application written and we come to deploy it, we don’t want the test files going out with it… You might be like me, have the files in a Web project – let’s face it, that’s how we’re pushed into doing it… So let’s stick with it! Now. I’m deploying via the wonders of the Web Deployment shizzle, but this also applies to the classic ‘installer’ project as well.. Baaaasically, we’re going to use the ‘Debug’ / ‘Release’ configurations to include given files. ?? OK, you know in the top of your visual studio editor, you (usually) have a drop down which predominantly reads ‘Debug’? Those are ‘configurations’. Mostly we don’t bother changing it, primarily due to laziness, but also the fact that we generally don’t see ‘Release’ as actually doing anything other than making it harder to find problems :) Well today my friends we’re going to change that bad boy… The next few steps are just helping you set up a new ‘Debug’ configuration, but you can just switch to the ‘Release’ configuration and skip to the end… First let’s go to the Configuration Manager. There are multiple ways, through the ‘Build’ menu (at the bottom), or via the drop down which currently has ‘Debug’ in it :) Got it? Select ‘New’ from the ‘Active solution configuration’ drop down: Create a new configuration, kind of like the picture below shows (or for those graphically challenged – Name: DebugWithNoTests, and Copy settings from: ‘Debug’, ensuring the ‘Create new project configurations’ checkbox is checked). Press OK. VS will do some shizzle, and in the Configuration manager, you will see pretty much exactly what you did before, only with ‘Debug’ replaced with ‘DebugWithNoTests’. Turn off the build options for the test projects. We won’t need them.. IF you skipped down from the top, this is where you’ll be wanting to stop!!! Close and now we’re one notepad step away from achieving our goals. Yes, I said notepad. You can’t do what we’re going to do in VS. (Pity). Go to the folder where your web project is, and right click on the ‘.csproj’ file. Now open it with notepad. Head on down to the ‘<Content Include’ bits, they’ll look like this: <ItemGroup> <Content Include="ClientBin\Tests.xap" /> ... </ItemGroup> Take this and modify each of the files you don’t want deployed and change to: <Content Include="ClientBin\Tests.xap" Condition="'$(Configuration)' == 'Debug'" /> Once you’ve got that sorted publish your project, once with the Debug configuration selected, and another with any other configuration (‘Release’, ‘DebugWithNoTests’ etc).. No files! Huzzah!

    Read the article

  • Can't access some websites using Ubuntu 13.10

    - by Adame Doe
    Something's wrong with Ubuntu. Since I've upgraded to 13.10, I can't access some websites for no apparent reason. I've tried everything imaginable to solve this problem : Made sure that MTUs are the same, Disabled IPv6 in both the network manager and used browsers, Deactivated my network keys, DMZed my computer, Used other DNS like Google and OpenDNS, Checked that no firewall was running my computer ... And it's the same result. I even tried to reinstall Ubuntu a couple of times, but no luck. The most annoying thing about it is I can't access wordpress.org! So, there's no way it could be an ISP restriction of some kind. When I use a VPN, I can access pretty much anything. I'm really frustrated because I have to use wordpress.org very often. Any clue? ifconfig adame@adame-ws:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:26:18:3d:b0:7c inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::226:18ff:fe3d:b07c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8024 errors:0 dropped:0 overruns:0 frame:0 TX packets:7966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:684480 (684.4 KB) TX bytes:616608 (616.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:8222 errors:0 dropped:0 overruns:0 frame:0 TX packets:8222 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:568269 (568.2 KB) TX bytes:568269 (568.2 KB) wlan0 Link encap:Ethernet HWaddr 00:19:70:40:85:eb inet addr:192.168.2.3 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::219:70ff:fe40:85eb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1464 Metric:1 RX packets:123705 errors:0 dropped:0 overruns:0 frame:0 TX packets:98141 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:94963545 (94.9 MB) TX bytes:10387470 (10.3 MB) /etc/hosts 127.0.0.1 localhost 127.0.1.1 adame-ws ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters tracepath wordpress.org 1: adame-ws.local 0.092ms pmtu 1500 1: 192.168.2.1 1.300ms asymm 2 1: 192.168.2.1 1.060ms asymm 2 2: no reply 3: no reply 4: no reply 5: no reply 6: no reply 7: no reply 8: no reply ... keep on going like that ping wordpress.org adame@adame-ws:~$ ping wordpress.org PING wordpress.org (66.155.40.250) 56(84) bytes of data. --- wordpress.org ping statistics --- 10 packets transmitted, 0 received, 100% packet loss, time 9071ms

    Read the article

  • core.* files eating up server space (~50MB)

    - by skytreader
    I'm renting server space from someone and, upon logging in my control panel after quite sometime, noticed an abnormal spike (~50MB) in the disk usage. Upon investigating, I found a lot of core.* files scattered around my public_html directory. Each one is more than 5MB in size but no more than 6MB. The * part is all numbers (in programming regex, that should be core\.\d+). I downloaded one and checked the contents. There was a lot of balderdash characters (NUL mostly, but also a scattering of ETB, ETX, STX) but there's this block of readable text which says: This text is part of the internal format of your mail folder, and is not a real message. It is created automatically by the mail system software. If deleted, important folder data will be lost, and it will be re-created with the data reset to initial values. Pretty self-explanatory. A few blocks above the text are some more readable messages that look like logs but is sandwiched in between non printable characters. I've extracted some below. Scan not valid for mh mailboxes Bogus character 0x%x in news state Can't rewrite news state %.80s Error closing backup news state %.80s No state for newsgroup %.80s found Now, a few concerns: Am I under attack? The messages seem to be about my webmail but I don't use my personal webmail that much---only for a vanity email address and an inbox for an outdated comments system. However, lately, I seem to notice a spike in the spam for my vanity mail. (Note: the comments system is covered by a captcha but every now and then some get through. My vanity email has a spam filter but it isn't as good as I'd like). Next, if this is a feature, can I turn it off? Is it advisable to? I've only 150MB so you see why I'm fretting over a 50MB spike. Some final details: my only server-side scripts are in PHP. The directory which accumulated the most number of these core files is the one containing the Wordpress-managed subdomain of my site. I manage my server through CPanel. Lastly, I decided to delete this files and after some checking nothing seems amiss in my websites nor in my mail. They are indeed the ones responsible for the ~50MB spike as my disk space usage is back to expected.

    Read the article

  • Unable to boot into 11.10 in normal (get a black screen) OR recovery (get just a flashing cursor, no cli)

    - by user1092284
    Okay, so I had a dual boot of Tango Studio (based on Ubuntu 10.04) and Windows XP. Yesterday I downloaded the .iso for Ubuntu 11.10 and attempted to install from a USB (my BIOS won't normally boot from USB but I had PLOP boot manager on a CD). I booted up Ubuntu from the USB and then from there formatted the partition with Tango on and installed Ubuntu 11.10. On booting up I came into Grub rescue mode. So I booted up from the USB again and used boot-repair to reinstall Grub. After this I would see the normal Grub menu, but on choosing Ubuntu I would come to a black screen. On choosing recovery mode it would begin starting normally with no obvious errors but instead of coming to a cli I would just get a blank screen with a flashing cursor on the top left, not accepting any input. I have since reformatted and reinstalled from a CD rather than USB and had the exact same problem. I used boot-repair again and the result is the same. Output of the most recent boot-repair is at http://paste.ubuntu.com/869805/ I have also tried editing the ubuntu grub entry and replacing quiet with text nomodeset as I saw in an answer to another question. This got me a bit further - I saw the purple ubuntu loading screen but still came to a blank screen after that. Anyway, in most of the other questions in which that is brought up the user is still able to boot into recovery, while I am not. Can anyone help? Thanks in advance, let me know if there's any more info I need to provide! EDIT FOR MORE INFO: I read something saying it's quiet splash that should be replaced with nomodeset. Earlier I had left splash in the line. So i tried it this way and it froze after displaying the following text: fsck from util-linux 2.19.1 mountall: Plymouth command failed mountall: Disconnected from Plymouth /dev/sda5:clean, 139359/1741488 files, 745830/6961125 blocks From a bit of googling it doesn't look like plymouth is essential, but I've checked and I do have the most current versions of mountall and plymouth installed so I don't know why there's a problem EDIT FOR MORE INFO AGAIN: I used dkpg --reconfigure plymouth cause I saw it mentioned in another forum and it still says plymouth command failed on boot

    Read the article

  • git workflow for separating commits

    - by gman
    Best practices with git (or any VCS for that matter) is supposed to be to have each commit do the smallest change possible. But, that doesn't match how I work at all. For example I recently I needed to add some code that checked if the version of a plugin to my system matched the versions the system supports. If not print a warning that the plugin probably requires a newer version of the system. While writing that code I decided I wanted the warnings to be colorized. I already had code that colorized error message so I edited that code. That code was in the startup module of one entry to the system. The plugin checking code was in another path that didn't use that entry point so I moved the colorization code into a separate module so both entry points could use it. On top of that, in order to test my plugin checking code works I need to go edit UI/UX code to make sure it tells the user "You need to upgrade". When all is said and done I've edited 10 files, changed dependencies, the 2 entry points are now both dependant on the colorization code, etc etc. Being lazy I'd probably just git add . && git commit -a the whole thing. Spending 10-15 minutes trying to manipulate all those changes into 3 to 6 smaller commits seems frustrating which brings up the question Are there workflows that work for you or that make this process easier? I don't think I can some how magically always modify stuff in the perfect order since I don't know that order until after I start modifying and seeing what comes up. I know I can git add --interactive etc but it seems, at least for me, kind of hard to know what I'm grabbing exactly the correct changes so that each commit is actually going to work. Also, since the changes are sitting in the current directory it doesn't seem like it would be easy to run tests on each commit to make sure it's going to work short of stashing all the changes. And then, if it were to stash and then run the tests, if I missed a few lines or accidentally added a few too many lines I have no idea how I'd easily recover from that. (as in either grab the missing lines from the stash and then put the rest back or take the few extra lines I shouldn't have grabbed and shove them into the stash for the next commit. Thoughts? Suggestions? PS: I hope this is an appropriate question. The help says development methodologies and processes

    Read the article

  • Threads slowing down application and not working properly

    - by Belgin
    I'm making a software renderer which does per-polygon rasterization using a floating point digital differential analyzer algorithm. My idea was to create two threads for rasterization and have them work like so: one thread draws each even scanline in a polygon and the other thread draws each odd scanline, and they both start working at the same time, but the main application waits for both of them to finish and then pauses them before continuing with other computations. As this is the first time I'm making a threaded application, I'm not sure if the following method for thread synchronization is correct: First of all, I use two global variables to control the two threads, if a global variable is set to 1, that means the thread can start working, otherwise it must not work. This is checked by the thread running an infinite loop and if it detects that the global variable has changed its value, it does its job and then sets the variable back to 0 again. The main program also uses an empty while to check when both variables become 0 after setting them to 1. Second, each thread is assigned a global structure which contains information about the triangle that is about to be rasterized. The structures are filled in by the main program before setting the global variables to 1. My dilemma is that, while this process works under some conditions, it slows down the program considerably, and also it fails to run properly when compiled for Release in Visual Studio, or when compiled with any sort of -O optimization with gcc (i.e. nothing on screen, even SEGFAULTs). The program isn't much faster by default without threads, which you can see for yourself by commenting out the #define THREADS directive, but if I apply optimizations, it becomes much faster (especially with gcc -Ofast -march=native). N.B. It might not compile with gcc because of fscanf_s calls, but you can replace those with the usual fscanf, if you wish to use gcc. Because there is a lot of code, too much for here or pastebin, I created a git repository where you can view it. My questions are: Why does adding these two threads slow down my application? Why doesn't it work when compiling for Release or with optimizations? Can I speed up the application with threads? If so, how? Thanks in advance.

    Read the article

  • Unintentional run-in with C# thread concurrency

    - by geekrutherford
    For the first time today we began conducting load testing on a ASP.NET application already in production. Obviously you would normally want to load test prior to releasing to a production environment, but that isn't the point here.   We ran a test which simulated 5 users hitting the application doing the same actions simultaneously. The first few pages visited seemed fine and then things just hung for a while before the test failed. While the test was running I was viewing the performance counters on the server noting that the CPU was consistently pegged at 100% until the testing tool gave up.   Fortunately the application logs all exceptions including those unhandled to the database (thanks to log4net). I checked the log and low and behold the error was:   System.ArgumentException: An item with the same key has already been added. (The rest of the stack trace intentionally omitted)   Since the code was running with debug on the line number where the exception occured was also provided. I began inspecting the code and almost immediately it hit me, the section of code responsible for the exception is trying to initialize a static class. My next question was how is this code being hit multiple times when I have a rudimentary check already in place to prevent this kind of thing (i.e. a check on a public variable of the static class before entering the initializing routine). The answer...the check fails because the value is not set before other threads have already made it through.   Not being one who consistently works with threading I wasn't quite sure how to handle this problem. Fortunately a co-worker recalled having to lock a section of code in the past but couldn't recall exactly how. After a quick search on Google the solution is as follows:   Object objLock = new Object(); lock(objLock) { //logic requiring lock }   The lock statement takes an object and tells the .NET runtime that the current thread has exclusive access while the code within brackets is executing. Once the code completes, the lock is released for another thread to utilize.   In my case, I only need to execute the inner code once to initialize my static class. So within the brackets I have a check on a public variable to prevent it from being initialized again.

    Read the article

  • How to do proper Alpha in XNA?

    - by Soshimo
    Okay, I've read several articles, tutorials, and questions regarding this. Most point to the same technique which doesn't solve my problem. I need the ability to create semi-transparent sprites (texture2D's really) and have them overlay another sprite. I can achieve that somewhat with the code samples I've found but I'm not satisfied with the results and I know there is a way to do this. In mobile programming (BREW) we did it old school and actually checked each pixel for transparency before rendering. In this case it seems to render the sprite below it blended with the alpha above it. This may be an artifact of how I'm rendering the texture but, as I said before, all examples point to this one technique. Before I go any further I'll go ahead and paste my example code. public void Draw(SpriteBatch batch, Camera camera, float alpha) { int tileMapWidth = Width; int tileMapHeight = Height; batch.Begin(SpriteSortMode.Texture, BlendState.AlphaBlend, SamplerState.PointWrap, DepthStencilState.Default, RasterizerState.CullNone, null, camera.TransformMatrix); for (int x = 0; x < tileMapWidth; x++) { for (int y = 0; y < tileMapHeight; y++) { int tileIndex = _map[y, x]; if (tileIndex != -1) { Texture2D texture = _tileTextures[tileIndex]; batch.Draw( texture, new Rectangle( (x * Engine.TileWidth), (y * Engine.TileHeight), Engine.TileWidth, Engine.TileHeight), new Color(new Vector4(1f, 1f, 1f, alpha ))); } } } batch.End(); } As you can see, in this code I'm using the overloaded SpriteBatch.Begin method which takes, among other things, a blend state. I'm almost positive that's my problem. I don't want to BLEND the sprites, I want them to be transparent when alpha is 0. In this example I can set alpha to 0 but it still renders both tiles, with the lower z ordered sprite showing through, discolored because of the blending. This is not a desired effect, I want the higher z-ordered sprite to fade out and not effect the color beneath it in such a manner. I might be way off here as I'm fairly new to XNA development so feel free to steer me in the correct direction in the event I'm going down the wrong rabbit hole. TIA

    Read the article

  • 12.04 Booting into Terminal

    - by user170796
    To preface this, I would like to say that I am completely new to Ubuntu and have essentially zero programming experience/experience working with command line and terminal. I installed Ubuntu because I would like to get into programming. If you could provide me with the simplest instructions possible, I would be grateful. I have a Lenovo Ideapad Y500 (Intel i7, NVidia GT 750m, 1TB HDD, 16GB SSD cache, 8GB RAM) with Windows 8 on it. Using a Live CD, I installed Ubuntu 12.04 onto a 75 GB partition. During the installation, I kept all default settings except for one thing; I decided to encrypt my home folder, and so checked the corresponding box. The installation completed, and I restarted. Once I restarted, I saw the options "Ubuntu, with Linux 3.2.0-23-generic" "Ubuntu, with Linux 3.2.0-23-generic (recovery mode)" "Memory test (memtest86+)" "Memory test (memtest86+, serial console 115200)" "Windows Recovery Environment (loader) (on /dev/sdb3)" "Windows 8 (loader) (on /dev/sdb5)" "System Setup" I chose the first option, and was directed to a screen with the Ubuntu logo and the row of five dots below that change from orange to white. Then, I was brought to a full screen terminal that prompted me to login, which I did. I saw no option to boot into GUI at all, and am lost. I've been searching around and have tried the "startx" command to no avail. Should the command have some sort of context or something? I've also tried selecting the recovery mode option from the boot manager. I've tried the resume option from the following menu, which eventually just shuts down the computer after displaying a lot of scrolling text that's too fast for me to read. I've also tried the failsafex mode from the recovery mode menu, which only brings up a terminal box at the bottom of the window that covers the entire bottom part of the screen. Commands won't work in this window. When I try to access Windows 8, I get a message saying that the EFI file path was not specified or something along those lines. I had to enable Secure Boot in order to access Windows 8 (I had disabled it to be able to boot from the Live CD), which is functioning normally. I am at a complete loss for what to do. Any help will be extremely appreciated. EDIT: Bonus question! If you could figure out a way for me to boot to Windows 8 without having to enable Secure Boot, it would save me a lot of trouble. I can deal with switching every time, but I'd rather not have to.

    Read the article

  • Can my machine run Ubuntu( kubuntu | xubuntu | mint ) 12.04 WELL?

    - by Steve
    I have a 9 year old computer packing the hardware listed below. My question is, can I run 12.04 ( Ubuntu, Kubuntu, MINT or Xubuntu ) WELL? I was running Ubuntu 10.10 and I upgraded to 12.04 by going through each release via the update manager: 11.04 - 11.10 -12.04 During the installation process for 12.04 I saw an error message that there was an error installing and setting up part of the kernel. Later, when I tried installing a package in synaptic, I got another error message mentioning the kernel. When I rebooted, I got told somehting about my video and graphics was not configured properly and that I would have to do it manually ( like I know ). It gave me the option to enter the system in low graphics mode, but it just hanged. I had an old livecd of Xubuntu 10.10 around so I used that to get into my computer and copy data over to an external hard drive. I think tried to install Xubuntu 10.10 from the livecd, with the option "download updates" checked. The install process moved along a bit, then halted for about 5 hours. I rebooted my machine and tried the Xubuntu 10.10 installer WITHOUT the option to "download updates". The install completed in about 15 minutes. So, all of that is making me wonder if there is someting about 12.04 that does not like my hardware. I'm willing to try again, but only if I know I will not have to spend hours just to get to an error message and a hosed up system like I did last night. I also think I have a lot more RAM than is being reported in the output below. I had extra ram installed last year. I'm not good with the command line readouts, but there seems like there should be a lot more. I wasn't thrilled with Unity. I am willing to try Kubuntu 12.04. Will I run into the same problems? What is the highest version of a *ubuntu can I upgrade to? Thanks CPU Model: Intel(R) Pentium(R) 4 CPU 2.53GHz Frequency: 2533.223 MHz L2 Cache: 512 KB Bogomips: 5066.44 Numbering: family(15) model(2) stepping(7) Flags: fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe up pebs bts cid RAM ~$ free -mt total used free shared buffers cached Mem: 1506 891 615 0 91 521 -/+ buffers/cache: 278 1227 Swap: 1609 0 1609 Total: 3116 891 2225 Video Card 01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a2) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. V9180 Magic Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16 Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Memory at f0000000 (32-bit, prefetchable) [size=64M] Expansion ROM at fe9e0000 [disabled] [size=128K] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb Motherboard Intel 845PE ATX 533FSB DDR333 USB2

    Read the article

  • Really weird GL Behaviour, uniform not "hitting" proper mesh? LibGdx

    - by HaMMeReD
    Ok, I got some code, and you select blocks on a grid. The selection works. I can modify the blocks to be raised when selected and the correct one shows. I set a color which I use in the shader. However, I am trying to change the color before rendering the geometry, and the last rendered geometry (in the sequence) is rendered light. However, to debug logic I decided to move the block up and make it white, in which case one block moves up and another block becomes white. I checked all my logic and it knows the correct one is selected and it is showing in, in the correct place and rendering it correctly. When there is only 1 it works properly. Video Of the bug in action, note how the highlighted and elevated blocks are not the same block, however the code for color and My Renderer is here (For the items being drawn) public void render(Renderer renderer) { mGrid.render(renderer, mGameState); for (Entity e:mGameEntities) { UnitTypes ut = UnitTypes.valueOf((String)e.getObject(D.UNIT_TYPE.ordinal())); if (ut == UnitTypes.Soldier) { renderer.testShader.begin(); renderer.testShader.setUniformMatrix("u_mvpMatrix",mEntityMatrix); renderer.texture_soldier.bind(0); Vector2 pos = (Vector2) e.getObject(D.COORDS.ordinal()); mEntityMatrix.set(renderer.mCamera.combined); if (mSelectedEntities.contains(e)) { mEntityMatrix.translate(pos.x, 1f, pos.y); renderer.testShader.setUniformf("v_color", 0.5f,0.5f,0.5f,1f); } else { mEntityMatrix.translate(pos.x, 0f, pos.y); renderer.testShader.setUniformf("v_color", 1f,1f,1f,1f); } mEntityMatrix.scale(0.2f, 0.2f, 0.2f); renderer.model_soldier.render(renderer.testShader,GL20.GL_TRIANGLES); renderer.testShader.end(); } else if (ut == UnitTypes.Enemy_Infiltrator) { renderer.testShader.begin(); renderer.testShader.setUniformMatrix("u_mvpMatrix",mEntityMatrix); renderer.testShader.setUniformf("v_color", 1.0f,1,1,1.0f); renderer.texture_enemy_infiltrator.bind(0); Vector2 pos = (Vector2) e.getObject(D.COORDS.ordinal()); mEntityMatrix.set(renderer.mCamera.combined); mEntityMatrix.translate(pos.x, 0f, pos.y); mEntityMatrix.scale(0.2f, 0.2f, 0.2f); renderer.model_enemy_infiltrator.render(renderer.testShader,GL20.GL_TRIANGLES); renderer.testShader.end(); } } }

    Read the article

  • How do I prevent Ubuntu gradually slowing down to a stop?

    - by user29165
    I really do not know what is causing the problem of my desktop environment (D.E.) gradually slowing down. It seems to happen in Gnome 3.2, LXDE, XFCE, and KDE. I am running Ubuntu 11.10 and this problem started happening from a fresh install. I have noticed that if I restart Gnome or otherwise re-log-in with any of the D.E.s the speed resets to normal. I don't seem to have and memory leaks that account for it and there are not any processes that are using excessive CPU cycles. Due to the symptoms I am guessing that there is an underlying package that interacts with all D.E.s that is the source of the problem. Just to clarify, in extreme situations, if I let the slowdown continue without a restart of the D.E. my system will finally get to a point where everything, even my clock, freezes. The time over which Gnome slows down (noticeably after 17 hrs) is much less than LXDE, or XFCE but eventually they freeze as well. I didn't mention Unity since I haven't used it enough to verify the problem, but I don't see why it should be different. Just in case this is relevant, I Suspend my computer rather than turn it off. I do this because of the greatly reduced load time and the 17 hrs I stated above is actual up-time, not time where the D.E. is actually active. However, the slow down does not seem to be affected by how long the computer has been in suspend mode. I know that it is possible that this problem is due to an interaction between two or more of the applications that I use and as such it may not be able to be duplicated by others. In the end I am just wondering (a) are other people experiencing this issue and (b) does anyone have some advice on where to start looking for a solution if one is not already known. I am even open to the idea of switching to the beta release of 12.04 if anyone thinks it will solve the problem. Edit: I took a video of my latest freeze that you can watch at http://youtu.be/flKUqUzCmdE, sorry about the audio. Edit: Since that video I checked my memory for errors and tried installing the proprietary video drivers. No memory errors were found and the proprietary video drivers made the display unusable so I had to uninstall them. Any thoughts?

    Read the article

  • Is Ubuntu recognizing and/or using my NVIDIA graphics card?

    - by user212860
    This is my first post here, and I'm pretty new to Ubuntu/Linux. I currently have no other OS except for Ubuntu 13.10. (I used to have Win7 until i got a new terabyte hard drive). My current PC build, if any of this helps: CPU: Intel i5 quad-core Graphics: NVIDIA GeForce GTX 650 RAM: 8 GB HDD: 1 TB SATA 3 Motherboard: MSi Z77 A-G41 OS Ubuntu 13.10 So I recently installed Ubuntu 13.10 and put Steam on it, and I'm seeing that my games run a lot slower than they did when I had Win7. I figured it was a graphics problem, so I checked System Settings Details Overview. It says in "Graphics" that I have "Gallium 0.4 on NVE7" (don't really know what that is). Does this mean that Ubuntu is not using my graphics card? In System Settings Software & Updates Additional Drivers, it clearly shows like this: NVIDIA Corporation: GK107 [GeForce GTX 650] -This device is using an alternative driver (And then it shows a list of drivers that I can switch back and forth to) So this is a bit confusing. In Software and Updates, it clearly shows that I have my NVIDIA card installed, and that I have a driver selected for it. But in System Settings, it shows I have some Gallium 0.4 thing. I had done a bit of research, and ended up typing command: "lspci|grep VGA" in the Terminal. It showed this in response: VGA compatible controller: NVIDIA Corporation GK107 [GeForce GTX 650] (rev a1) The Terminal seems to recognize my graphics card. What it looks like to me, is that I don't have the proper driver, and I might be using my CPU's integrated graphics. When I switch around which driver I am using in that list, it still does not see my card in System Settings. Some of the drivers in the list give me some sort of OpenGL error when I try to run a game. It might just be that my games are running slow because the game developers have not optimized it for Ubuntu that well. However, that still doesn't take away from the fact that System Settings is not showing my NVIDIA card. TL;DR Version: How do I know if my video card is being recognized/used? If my video card is not being used, what is the best way fix that? Please make your answers easy to understand. I do not mind wordy responses, as long as I can follow what you're saying. Any help would be greatly appreciated! Thanks, Jabber5

    Read the article

  • Brute force algorithm implemented for sudoku solver in C [closed]

    - by 0cool
    This is my code that I have written in C.. It could solve certain level of problems but not the harder one.. I could not locate the error in it, Can you please find that.. # include <stdio.h> # include "sudoku.h" extern int sudoku[size][size]; extern int Arr[size][size]; int i, j, n; int BruteForceAlgorithm (void) { int val; for (i=0; i<size; i++) { for (j=0; j<size; j++) { if (sudoku[i][j]==0) { for (n=1; n<nmax; n++) { val = check (i,j,n); if ( val == 1) { sudoku[i][j]=n; // output(); break; } else if ( val == 0 && n == nmax-1 ) get_back(); } } } } } int get_back (void) { int p,q; int flag=0; for ( p=i; p>=0; p-- ) { for (q=j; q>=0; q-- ) { flag=0; if ( Arr[p][q]==0 && !( p==i && q==j) ) { if ( sudoku[p][q]== nmax-1 ) sudoku[p][q]=0; else { n = sudoku[p][q]; sudoku[p][q]=0; i = p; j = q; flag = 1; break; } } } if ( flag == 1) break; } } Code description: Sudoku.h has definitions related to sudoku solver. 1. size = 9 nmax = 10 2. check(i,j,n) returns 1 if a number "n" can be placed at (i,j) or else "0". What does this code do ? The code starts iterating from sudoku[0][0] to the end... if it finds a empty cell ( we take cell having "0" ), it starts checking for n=1 to n=9 which can be put in that.. as soon as a number can be put in that which is checked by check() it assigns it and breaks from loop and starts finding another empty cell. In case for a particular cell if it doesn't find "n" which can be assigned to sudoku cell.. it goes back to the previous empty cell and start iterating from where it stopped and assigns the next value and continues, Here comes the function get_back(). it iterates back..

    Read the article

  • Efficient way to find unique elements in a vector compared against multiple vectors

    - by SyncMaster
    I am trying find the number of unique elements in a vector compared against multiple vectors using C++. Suppose I have, v1: 5, 8, 13, 16, 20 v2: 2, 4, 6, 8 v3: 20 v4: 1, 2, 3, 4, 5, 6, 7 v5: 1, 3, 5, 7, 11, 13, 15 The number of unique elements in v1 is 1 (i.e. number 16). I tried two approaches. Added vectors v2,v3,v4 and v5 into a vector of vector. For each element in v1, checked if the element is present in any of the other vectors. Combined all the vectors v2,v3,v4 and v5 using merge sort into a single vector and compared it against v1 to find the unique elements. Note: sample_vector = v1 and all_vectors_merged contains v2,v3,v4,v5 //Method 1 unsigned int compute_unique_elements_1(vector<unsigned int> sample_vector,vector<vector<unsigned int> > all_vectors_merged) { unsigned int duplicate = 0; for (unsigned int i = 0; i < sample_vector.size(); i++) { for (unsigned int j = 0; j < all_vectors_merged.size(); j++) { if (std::find(all_vectors_merged.at(j).begin(), all_vectors_merged.at(j).end(), sample_vector.at(i)) != all_vectors_merged.at(j).end()) { duplicate++; } } } return sample_vector.size()-duplicate; } // Method 2 unsigned int compute_unique_elements_2(vector<unsigned int> sample_vector, vector<unsigned int> all_vectors_merged) { unsigned int unique = 0; unsigned int i = 0, j = 0; while (i < sample_vector.size() && j < all_vectors_merged.size()) { if (sample_vector.at(i) > all_vectors_merged.at(j)) { j++; } else if (sample_vector.at(i) < all_vectors_merged.at(j)) { i++; unique ++; } else { i++; j++; } } if (i < sample_vector.size()) { unique += sample_vector.size() - i; } return unique; } Of these two techniques, I see that Method 2 gives faster results. 1) Method 1: Is there a more efficient way to find the elements than running std::find on all the vectors for all the elements in v1. 2) Method 2: Extra overhead in comparing vectors v2,v3,v4,v5 and sorting them. How can I do this in a better way?

    Read the article

  • 2 javascripts problem

    - by pradeep
    <?php global $user; $userId = $user->uid; /* start with default */ $myresult = ""; /* All Includes - start */ include_once('db.php'); include_once('valid-scripts/validateData.php'); /* All Includes - end */ /* Build All required Variables - start */ $alias = $_GET['alias']; $product = $_GET['product']; $product = strtolower(substr($product,0,-1)); $master_table = $product.'_master'; $rating_master_table = $product.'_rating_master'; $rating_table = $product.'_rating'; $numProperties = 15; /* Build All required Variables - end */ /* Add all Styles required - start */ $myresult .= '<link href="/jquery.rating.css" type="text/css" rel="stylesheet"/>'; /* Add all Styles required - end */ /* Show Hide Variables/parameters - start */ include_once('all_include_files/show_hide.php'); /* Show Hide Variables/parameters - end */ /* All Javascript - start */ //$myresult .= '<script src="/jquery.rating.js" type="text/javascript" language="javascript"></script>'; ?> <style> #tabs { //font-size: 90%; //margin: 20px 0; margin: 2px 0; } #tabs ul { float: right; background: #E3FEFA; width: 600px; //padding-top: 4px; } #tabs li { margin-left: 8px; list-style: none; } * html #tabs li { display: inline; /* ie6 double float margin bug */ } #tabs li, #tabs li a { float: left; } #tabs ul li a { text-decoration: none; //padding: 8px; color: #0073BF; font-weight: bold; } #tabs ul li.active { background: #CEE1EF url(/all_include_files/img/nav-right.gif) no-repeat right top; } #tabs ul li.active a { background: url(/all_include_files/img/nav-left.gif) no-repeat left top; color: #333333; } #tabs div { //background: #CEE1EF; clear: both; //padding: 20px; min-height: 200px; } #tabs div h3 { text-transform: uppercase; margin-bottom: 10px; letter-spacing: 1px; #tabs div p { line-height: 150%; } </style> <script src="/jquery.rating.js" type="text/javascript" language="javascript"></script> <script src="/jquery.metadata.js" type="text/javascript" language="javascript"></script> <script type='text/javascript'> function openComment(number) { alert('working'); $('#comment'+number).css('display',''); } $('.star').rating({ callback: function(value, link){ alert(value); } }); $(document).ready(function() { //$('#tabs div').hide(); //$('#tabs div:first').show(); $('#tabs ul li:first').addClass('active'); $('#tabs ul li a').click(function() { $('#tabs ul li').removeClass('active'); $(this).parent().addClass('active'); var currentTab = $(this).attr('href'); $('#tabs div').hide(); $(currentTab).show(); return false; }); $("#clickit").click(function() { $.post("/mobile/tablechange.php",{ p1:'<?php echo $brand ?>',p2:'<?php echo $model ?>',userid:'<?php echo $userid ?>' } ,function(data){ $("#changetable").html(data); }); }); $('div.expandable p').expander({ slicePoint: 200, // default is 100 expandText: 'more &raquo;', // default is 'read more...' collapseTimer: 0, // re-collapses after 5 seconds; default is 0, so no re-collapsing userCollapseText: '[^]' // default is '[collapse expanded text]' }); }); </script> <?php /* All Javascript - end */ /* Form Processing after submit - start */ /* Form Processing after submit - end */ /* Actual Form or Page - start */ /*fetch all data needed */ /* initial query */ $result_product = query_product_table($product,$alias); /*fetch property names of product */ $product_properties = master_table($master_table); /*rating table query */ $master_rating_properties = master_rating_table($rating_master_table); /*get user ratings*/ $user_ratings = user_ratings($userId,$alias,$rating_table); $myresult .= '<div class=\'Services\'>'; //$myresult .="<form name ='form1' id='form1' method = 'POST' action='".$_SERVER['php_self'] ."'>"; if(!$result_product) { header('Location: /page-not-found'); } else { $row_product = mysql_fetch_array($result_product); $myresult .= "<h3 class='newstyle'>".$row_product['alias']." <a style='float:right;padding-right:20px;color:white;text-decoration:underline;' href='/'>Back</a> </h3>"; /* start actual product display - start*/ $myresult .= "<div class=\"product\">"; /* start table 1*/ $myresult .= '<table border=\'0\' cellspacing=\'0\' cellpadding=\'0\' style=\'width:580px; table-layout:fixed;\'>'; $myresult .= '<tr>'; $myresult .='<td valign=\'top\'>'; /* start table 2*/ $myresult .='<table width=\'100%\' border=\'0\' cellspacing=\'0\' cellpadding=\'0\'>'; $myresult .= '<tr>'; $myresult .= '<td valign=\'top\' style=\'width:164px;\'>'; /* start table 3*/ $myresult .= '<table style=\'width:164px;\' border=\'0\' cellspacing=\'0\' cellpadding=\'0\'>'; $myresult .= "<tr>"; /* start of the pic row */ $myresult .= '<td align=\'center\' class=\'various_product\'>'; if($row_product['pic'] != "") { $myresult .= '<ul id=\'mycarousel\' style=\'display:\';>'; $myresult .= '<li><a href=\'/all_image_scripts/origpicdisplay.php?product='.rawurlencode($product).'&alias='.rawurlencode($alias).'&picid=pic&p= \'rel=\'lightbox[roadtrip]\'><img src=\'/all_image_scripts/picdisplay1.php?product='.rawurlencode($product).'&alias='.rawurlencode($alias).'\'></img></a></li>'; for($p = 1; $p <= 4; $p++) { if($row_product['pic'.$p] != "") { $myresult .= '<li><a href=\'/all_image_scripts/origpicdisplay.php?product='.rawurlencode($product).'&alias='.rawurlencode($alias).'&picid=pic'.rawurlencode($p).'&p='.rawurlencode($p).'\' rel=\'lightbox[roadtrip]\'><img src=\'/all_image_scripts/thumbpicdisplay.php?product='.rawurlencode($product).'&alias='.rawurlencode($alias).'&picid=pic'.rawurlencode($p).'\'></img></a></li>'; } } $myresult .= '</ul>'; } else { $myresult .= "<img width='50' height='70' src='/images/no-image.gif'></img>"; } jcarousel_add('#mycarousel', array('horizontal' => TRUE,'scroll' => 1,'visible' => 1)); $myresult .= "</td>"; /* end display of pic td*/ $myresult .= "</tr>"; /* end display of pic tr*/ $myresult .= "</table></td>"; /* end display of pic table and earlier td - Still 1 open TR td table tr -hint*/ $myresult .= '<td style=\'width:450px;\'>'; /*table - 4*/ $myresult .= '<table width=\'100%\' border=\'0\' cellspacing=\'0\' cellpadding=\'0\' style=\'display:block;\'>'; /* Start showing property and values */ $myresult .= '<tr>'; $myresult .= '<td class=\'tick\'><img src=\'/images/ul_li_bg.gif\' width=\'12\' height=\'12\' /></td>'; $myresult .= '<td class=\'leftText\'>'.ucfirst($product).':</td>'; $myresult .= '<td class=\'rightText\'>'.$row_product['alias'] .'</td>'; $myresult .= "</tr>"; for($j = 3; $j <= 5 ; $j++){ if($product_properties['property'.$j.'_name'] != "") { if($row_product['property'.$j] != "") { $myresult .= '<tr>'; $myresult .= '<td class=\'tick\'><img src=\'/images/ul_li_bg.gif\' width=\'12\' height=\'12\' /></td>'; $myresult .= '<td class=\'leftText\'>'.$product_properties['property'.$j.'_name'].':</td>'; $myresult .= '<td class=\'rightText\'>'.$row_product['property'.$j] .'</td>'; $myresult .= '</tr>'; } /* end if*/ } /* end if*/ } /* end for*/ /* show hide block */ $myresult .= '<tbody id=\'extra_properties\' style=\'display: none;\'>'; for($j = 6; $j <= 15 ; $j++){ if($product_properties['property'.$j.'_name'] != "") { if($row_product['property'.$j] != "") { $myresult .= '<tr>'; $myresult .= '<td class=\'tick\'><img src=\'/images/ul_li_bg.gif\' width=\'12\' height=\'12\' /></td>'; $myresult .= '<td class=\'leftText\'>'.$produtc_properties['property'.$j.'_name'].':</td>'; $myresult .= '<td class=\'rightText\'>'.$row_product['property'.$j] .'</td>'; $myresult .= '</tr>'; } /* end if*/ } /* end if*/ } /* end for */ $myresult .= '</tbody>'; /* end show/hide tbody */ $myresult .= '<tr>'; $myresult .= '<td>'; $myresult .= '&nbsp;'; $myresult .= '</td>'; $myresult .= '<td>'; $myresult .= '&nbsp;'; $myresult .= '</td>'; $myresult .= '<td align=\'right\' style=\'text-align:right;text-decoration:underline;\'>'; $myresult .= '<a class=\'right_link\' href=\'javascript:showMore()\'>Show Additional Details...</a>'; $myresult .= '</td>'; $myresult .= '</tr>'; /* End showing property and values */ $showreview = 'display:'; /* review show hide */ /*$myresult .= '<tbody '.$showreview.'>'; $myresult .= '<tr>'; $myresult .= '<td colspan=\'2\'><span class=\'reviews\'>'; //check //$numreviews = getreviewcount($brand,$model,'mobile_user_reviews'); if($numreviews > 0) { $myresult .= '<a href=\'mobilereviews?alias='.rawurlencode($alias).'\'> <span>$numreviews Reviews</span></a>'; } else { $myresult .= " $numreviews Reviews"; } $myresult .= "</span></td>"; $myresult .= "</tr>"; */ $myresult .= "</tbody>"; /* review show hide - end */ /* count show hide */ $myresult .= '<tbody '.$showcount.'>'; $myresult .= '<tr>'; $myresult .= '<td colspan=\'2\'><span class=\'reviews\'>'; //check //$totalvotes = gettotalvotes($row['property1'],$row['property2'],'mobile_rating'); $myresult .= "</td>"; $myresult .= "</tr>"; $myresult .= "</tbody>"; /* count show hide - end */ $myresult .= "</table></td>"; /* end table 4 */ $myresult .= '</tr>'; /* end 1 row and remaining tr , td ,table */ $myresult .= '</table></td>'; $myresult .= '</tr>'; /* remianing only 1 table */ /* ratings - positive last section starts here */ $max= array(); for ($l = 1 ; $l < 15; $l++){ if($row_product['property'.$l.'_avg']){ $maxarray = 0; $maxarray = $row_product['property'.$l.'_avg']; $max['rating'.$l.'_name'] = $maxarray; } } if(count($max) >0 ) { include('all_include_files/min_max_properties.php'); } if(($row_product['freshness'] <= strtotime("-3 month"))) { $image_type= 'old'; } else if(($row_product['freshness'] <= strtotime("-2 month"))) { $image_type= 'bitold'; } else if(($row_product['freshness'] <= strtotime("-1 month")) || ($row_product['freshness'] > strtotime("-1 month"))) { $image_type= 'new'; } $img_name = $image_type; $myresult .= "<tr>"; $myresult .= "<td>"; $myresult .= "<table width='100%' border='0'>"; $myresult .= "<tr>"; $myresult .= "<td width='170' class=\"ratingz\"><span><u>Overall rating</u></span></td>"; $myresult .= "<td width='150' class=\"ratingz\"><span><u>Positive</u></span></td>"; $myresult .= "<td width='150' class=\"ratingz\"><span><u>Negative</u></span></td>"; if($img_name == 'new'){ $images = "<img src='/sites/default/files/battery-discharging-100.png' width='40' height='40'></img>"; } else if($img_name == 'bitold'){ $images = "<img src='/sites/default/files/battery-discharging-80.png' width='40' height='40'></img>"; } else if($img_name == 'old'){ $images = "<img src='/sites/default/files/battery-discharging-0.png' width='40' height='40'></img>"; } else { $images = ""; } $myresult .= "<td rowspan='2'><p ".$showbattery.">". $images ."</p></td>"; $myresult .= "</tr>"; $myresult .= "<tr>"; $myresult .= "<td>"; $i++; for($k = 0.5; $k <= 10.0; $k+=0.5) { $overall = roundOff($row_product['overall_rating']); if($overall == $k) { $chk ="checked"; } else { $chk = ""; } $myresult .= '<input class=\'star {split:2}\' type=\'radio\' value=\''. $k .'\' '.$chk.' title=\''. $k.' out of 10 \' disabled />'; } $myresult .= '</td>'; $myresult .= '<td ><span>'.$positive.'</span></td>'; $myresult .= '<td ><span>'.$negative.'</span></td>'; $myresult .= '</tr>'; $myresult .= '</table></td>'; $myresult .= '</tr>'; /* ratings - positive last section ends here */ $myresult .= '<tr>'; if($row_product['description'] != ""){ if(words_count($row_product['description']) > 8){ $myresult .= '<td><p><span class=\'description\'><strong><u>Description</u>:</strong></span>&nbsp;&nbsp; <div class=\'expandable\'><p>'.$row_product['description'].'</div></p></p></td>'; } else { $myresult .= '<td><p><span class=\'description\'><strong><u>Description</u>:</strong></span>&nbsp;&nbsp;'. $row_product['description'] .'</p></td>'; } } $myresult .= '</tr>'; $myresult .= '</table>'; /* end 1st table */ $myresult .= '</div>'; /* start actual product display - end*/ /*start the form to take ratings */ $myresult .= '<div id=\'tabs\'>'; $myresult .= '<ul>'; $myresult .= '<li><a href=\'#tab-1\'>Ratings</a></li>'; $myresult .= '<li><a href=\'#tab-2\'>Click here to rate</a></li>'; $myresult .= '</ul>'; $myresult .= '<div id=\'tab-1\'>'; /* actual rating table - start - jsut display ratings */ $myresult .= '<table id=\'rounded-corner\'>'; /* thead - start */ $myresult .= '<thead>'; $myresult .= '<tr>'; $myresult .= '<th width=\'30%\' class=\'rounded-company\' scope=\'col\'><span style=\'font: normal 18px Arial, Helvetica, sans-serif; color:#FFF;\'>Ratings</span></th>'; $myresult .= '<th width=\'70%\' colspan=\'2\'class=\'rounded-q4\' scope=\'col\'><a href=\'#rounded-corner\' id=\'clickit\' style=\'color:white;text-decoration:underline;\' $disabled ></a></th> '; /*$myresult .= '<th width=\'70%\' colspan=\'2\'class=\'rounded-q4\' scope=\'col\'><a href=\'#rounded-corner\' id=\'clickit\' style=\'color:white;text-decoration:underline;\' $disabled >Click here to rate</a></th> ';*/ $myresult .= '</tr>'; $myresult .= '</thead>'; /* thead - end */ /* tbody - start */ $myresult .= '<tbody>'; /*start printing the table wth feature and ratings */ for ($i = 1 ; $i < $numProperties; $i++){ if($master_rating_properties['rating'.$i.'_name']){ $myresult .= '<tr>'; $myresult .= '<td width=\'22%\'>'; $indfeature = 0; $indfeature = $row_product['property'.$i.'_avg']; $myresult .= $master_rating_properties['rating'.$i.'_name'].' ( '.$indfeature .')'; $myresult .= '</td>'; $myresult .= '<td colspan=\'0\' width=\'38%\' >'; $tocheck = $indfeature; for($k = 0.5; $k <= 10.0; $k+=0.5){ $tocheck = roundOff($tocheck); if(($tocheck) == $k) { $chk = "checked"; } else { $chk = ""; } $myresult .= '<input class=\'star {split:2}\' type=\'radio\' name=\'drating'.$i.'\' id=\'drating'.$i.''.$k.'\' value=\''. $k .'\' '.$chk.' title=\''. $k.' out of 10 \' disabled \'/>'; } /* for k loop end */ $myresult .= '</tr>'; } /* end if loop */ } /* end i for loop */ $myresult .= '</tbody>'; /* end tbody */ /* footer round corner start */ $myresult .= '<tfoot>'; $myresult .= '<tr>'; $myresult .= '<td class=\'rounded-foot-left\'>&nbsp;</td>'; $myresult .= '<td class=\'rounded-foot-right\' colspan=\'4\' >'; $myresult .= '</td>'; $myresult .= '</tr>'; $myresult .= '</tfoot>'; $myresult .= '</table>'; /*round corner table end */ $myresult .= '</div>'; /*end 1st tab */ /*start 2nd tab */ $myresult .= '<div id=\'tab-2\'>'; $myresult .= '<form name =\'form1\' id=\'form1\' method = \'POST\' action=\''.$_SERVER['php_self'] .'\'>'; /* actual rating table - start - actual rate/update */ $myresult .= '<table id=\'rounded-corner\'>'; /* thead - start */ $myresult .= '<thead>'; $myresult .= '<tr>'; $myresult .= '<th width=\'30%\' class=\'rounded-company\' scope=\'col\'><span style=\'font: normal 18px Arial, Helvetica, sans-serif; color:#FFF;\'>Ratings</span></th>'; $myresult .= '<th width=\'70%\' colspan=\'2\'class=\'rounded-q4\' scope=\'col\'></th>'; $myresult .= '</tr>'; $myresult .= '</thead>'; /* thead - end */ /* tbody - start */ $myresult .= '<tbody>'; unset($i); /*start printing the table wth feature and ratings */ for ($i = 1 ; $i < $numProperties; $i++){ if($master_rating_properties['rating'.$i.'_name']){ $myresult .= '<tr>'; /*fetch ratings and comments - 1st make it to null */ $indfeature = 0; $comment = ''; $indfeature = $user_ratings['rating'.$i]; if($indfeature == NULL){ $indfeature = 0; } $comment = $user_ratings['rating'.$i.'_comment']; $myresult .= '<td width=\'22%\'>'; $myresult .= $master_rating_properties['rating'.$i.'_name'].' ( '.$indfeature.' )'; $myresult .= '</td>'; $myresult .= '<td colspan=\'0\' width=\'38%\' >'; if(($userId != '0') && (is_array($user_ratings))) { $tocheck = $indfeature; } else { $tocheck = '0'; } for($k = 0.5; $k <= 10.0; $k+=0.5){ $tocheck = roundOff($tocheck); if(($tocheck) == $k) { $chk = "checked"; } else { $chk = ""; } $myresult .= '<input class=\'star {split:2}\' type=\'radio\' name=\'rating'.$i.'\' id=\'rating'.$i.''.$k.'\' value=\''. $k .'\' '.$chk.' title=\''. $k.' out of 10 \' '.$disabled.' \' />'; } /* for k loop end */ $myresult .= '</td>'; $myresult .= '<td width=\'40%\'>'; $myresult .= '<input title=\'Reason for this Rating.. \'type=\'text\' size=\'25\' name=\'comment'.$i.'\' id=\'comment'.$i.'\' style=\'display:;\' maxlength=\'255\' value="'.$comment.'">'; $myresult .= '</td>'; $myresult .= '</tr>'; } /* end if loop */ } /* end i for loop */ $myresult .= '</tbody>'; /* end tbody */ /* footer round corner start */ $myresult .= '<tfoot>'; $myresult .= '<tr>'; $myresult .= '<td class=\'rounded-foot-left\'>&nbsp;</td>'; $myresult .= '<td class=\'rounded-foot-right\' colspan=\'4\' >'; if(($userId != '0') && (is_array($user_ratings))) { $myresult .= '<input type=\'button\' id=\'update_form\' value=\'Update\'>'; } else { $myresult .= '<input type=\'button\' id=\'save_form\' value=\'Save\'>'; } $myresult .= '</td>'; $myresult .= '</tr>'; $myresult .= '</tfoot>'; $myresult .= '</table>'; /*round corner table end */ $myresult .= '</form>'; /*end the form to take ratings */ $myresult .= '</div>'; /*end 2nd tab */ $myresult .= '</div>'; /*end tabs div */ /* actual rating table - end */ /* 1st form ends here id- ratings_form */ } /* end of if loop result_product loop */ /* start table 3 - overall comment*/ $myresult .= '<table border=\'0\' cellspacing=\'0\' cellpadding=\'0\' style=\'width:580px; table-layout:fixed;\' id=\'rounded-corner\'>'; $myresult .= '<tbody>'; /* thead - start */ $myresult .= '<thead>'; $myresult .= '<tr>'; $myresult .= '<th width=\'100%\' colspan=\'2\' class=\'rounded-company\' scope=\'col\'><span style=\'font: normal 18px Arial, Helvetica, sans-serif; color:#FFF;\'>Overall Comments</span></th>'; $myresult .= '<th colspan=\'3\' class=\'rounded-q4\' scope=\'col\'></th>'; $myresult .= '</tr>'; $myresult .= '</thead>'; /* thead - end */ $myresult .= '<tr>'; $myresult .= '<td colspan=\'4\'>'; $myresult .= '<textarea title=\'OverAll Comment\' name=\'overall_comment\' cols=\'65\'></textarea>'; $myresult .= '</td>'; $myresult .= '</tr>'; $myresult .= '<tbody>'; $myresult .= '</table>'; /* end table 3 - overall comment*/ /* start table 4 - summary*/ $myresult .= '<table border=\'0\' cellspacing=\'0\' cellpadding=\'0\' style=\'width:580px; table-layout:fixed;\' id=\'rounded-corner\'>'; $myresult .= '<tbody>'; /* thead - start */ $myresult .= '<thead>'; $myresult .= '<tr>'; $myresult .= '<th colspan=\'2\' class=\'rounded-company\' scope=\'col\'><span style=\'font: normal 18px Arial, Helvetica, sans-serif; color:#FFF;\'>Your Opinion</span></th>'; $myresult .= '<th colspan=\'2\'class=\'rounded-q4\' scope=\'col\'></th>'; $myresult .= '</tr>'; $myresult .= '</thead>'; /* thead - end */ $myresult .= '<tr>'; $myresult .= '<td colspan=\'2\'>'; $myresult .= 'Do you Agree with the Ratings'; $myresult .= '</td>'; $myresult .= '<td colspan=\'2\'>'; $myresult .= 'Was the Information Helpful'; $myresult .= '</td>'; $myresult .= '</tr>'; $myresult .= '<tr>'; $myresult .= '<form name=\'form2\' id=\'form2\' method=\'post\'>'; $myresult .= '<td>'; $myresult .= '<input type=\'button\' class=\'agree\' value=\'agree\'>'; $myresult .= '</td>'; $myresult .= '<td>'; $myresult .= '<input type=\'button\' class=\'disagree\' value=\'disagree\'>'; $myresult .= '</td>'; $myresult .= '<input type=\'hidden\' name=\'agree_disagree\' id=\'agree_disagree\'>'; $myresult .= '</form>'; $myresult .= '<form name=\'form3\' id=\'form3\' method=\'post\'>'; $myresult .= '<td>'; $myresult .= '<input type=\'button\' class=\'helpful\' value=\'Helpful\'>'; $myresult .= '</td>'; $myresult .= '<td>'; $myresult .= '<input type=\'button\' class=\'nothelpful\' value=\'Not Helpful\'>'; $myresult .= '</td>'; $myresult .= '<input type=\'hidden\' name=\'help_nohelp\' id=\'help_nohelp\'>'; $myresult .= '</form>'; $myresult .= '</tr>'; $myresult .= '</tbody>'; $myresult .= '</table>'; /*end table 4 summary table */ $myresult .= '</div>'; /* Actual Form or Page - end */ echo $myresult; //echo 'Product: '.$product; //echo '<br/>Alias: '.$alias; ?> hey this code is working fine for me . as required. the star class code is taken from http://www.fyneworks.com/jquery/star-rating/ ... it works well.. but when i insert code to add tabs for content ,the starts is not visible at all. but when i check source code. the stars are actually there . dono whats the prob. any suggestions on this this is the tabs code $('#tabs div').hide(); ('#tabs div:first').show(); $('#tabs ul li:first').addClass('active'); $('#tabs ul li a').click(function() { $('#tabs ul li').removeClass('active'); $(this).parent().addClass('active'); var currentTab = $(this).attr('href'); $('#tabs div').hide(); $(currentTab).show(); return false; });

    Read the article

  • How to use tscon on Windows7?

    - by Radek
    I need to run overnight automation testing using RFT and IE on Windows7 virtual machine. I found that restarting the Windows box before the testing starts helps. I am moving the production environment from Windows XP to Windows 7. RFT used to complain when running RFT scripts that CRFCN0557E: Activation failed when running under a Terminal Services environment. This may be caused by using a minimized terminal window - try playing back without minimizing the terminal window (it does not need to be full-screen). Running tscon.exe 0 /dest:console prior starting any RFT script fix the error on Windows XP. But not on Windows7. I did some research and was trying for hours to fix that but nothing helped. There is no screen saver turned on on Windows7. I tried to run both but nothing helped. tscon.exe 0 /dest:console tscon.exe 1 /dest:console On Windows7 tscon returns {ErrorPrintf(): LoadString failed, Error 15105, (0x00003B01)} Error [15105]:The resource loader cache doesn't have loaded MUI entry. Error [0]:The operation completed successfully. On Windows XP tscon returns Could not connect sessionID 0 to sessionname console, Error code 7045 Error [7045]:The requested session access is denied. I just double checked that running tscon.exe 0 /dest:console on Windows XP solves the issue. Cannot understand the output of the tscon command then. Any idea how I can run RFT scripts after I restart the Windows box automatically? Preferably without involving any other computer. I was even thinking to use the old Windows XP to make remote desktop session to make RFT happy. I hope there is other better solution to that.

    Read the article

  • Error accessing or executing Nagios / Icinga binary '/usr/sbin/nagios'. Cannot run the mandatory syntax check

    - by Zim3r
    I see an error while using NConf interface in Generate Nagios config Error accessing or executing Nagios / Icinga binary '/usr/sbin/nagios'. Cannot run the mandatory syntax check. I checked Apache Error_log and it says: sh: /usr/sbin/nagios: Permission denied I tried changing permissions and ownership but no change. How can I fix this? Edit: ls -l /usr/sbin/nagios -rwxrwxrwx. 1 apache apache 644184 Jul 2 02:10 /usr/sbin/nagios ps -ef | egrep 'httpd|apache' root 4175 1 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4177 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4178 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4179 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4180 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4181 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4182 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4183 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4184 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4559 4175 0 11:31 ? 00:00:00 /usr/sbin/httpd root 4888 4854 0 12:26 pts/1 00:00:00 egrep httpd|apache

    Read the article

  • virtualbox installing iso Error "could not find a valid v7 on sda"

    - by MountainX
    I decided to try this suggestion to install Android x86 on Virtual Box. I'm following those steps and I'm at #4. I used the android-x86-4.0-RC1-amd_brazos.iso (because I have a ThinkPad that this might be compatible with and it seemed as good as any of the other choices...) I'm getting an endless series of errors: .[numbers] VFS: could not find a valid v7 on sda. .[numbers] VFS: could not find a valid v7 on sda. repeating... For storage, I made a VDI image sized at 4.0 GB (dynamically allocated) attached on SATA Port 0. Background and more details: I'm running Kubuntu 12.04. I installed VirtualBox 4.1.12 after adding deb http://download.virtualbox.org/virtualbox/debian precise contrib to my sources. EDIT: Now I'm wondering if I installed the right package. I verified that I'm running 4.1.12. But I installed it with apt-get install virtualbox instead of the recommended apt-get install virtualbox-4.1. I checked just now and see this: apt-cache search virtualbox virtualbox - x86 virtualization solution - base binaries virtualbox-4.1 - Oracle VM VirtualBox But when I run VirtualBox, I get the Oracle VM VirtualBox Manager version 4.1.12, so I think I'm OK. I did see one minor issue (possibly related to this question) when installing VB, but in my case I don't think it is actually an error at all: * No suitable module for running kernel found [fail] invoke-rc.d: initscript virtualbox, action "restart" failed. VirtualBox installed and seems to be running fine. I just can't get the ISO image to install. The error is as shown above.

    Read the article

  • Rebuilding array on 3ware 9690SA-8I

    - by Tim Jones
    I have a RAID10 (8x1TB) array on a 3ware 9690 card running on an Ubuntu 1110 server. There was a kernel update so I scheduled a reboot after which the array was inaccessible. I checked the status a drive has died in the array, but the controller has thrown the entire array into an 'inoperable' state instead of simply degraded (what's the point of the RAID now ;-). After taking out the 'dead' drive I run a quick test to find it completely functional without a bad sector to be found. I try to put the drive back in but the array still marks the disk as degraded (remembering serial number or something??) and the entire array as inoperable... So I swap it out for a known working drive (not the same capacity but higher - should still work) and initiate a rebuild with the the new drive as a replacement. This fails instantly with the error "(0x0B:0x0033): Unit busy : Failed to start Rebuild on Unit 0". The unit shouldn't be busy as it is not mounted (the card itself is listed with lshw but the array it provides is not). I'm pretty much at an impasse now, I don't understand how I can have a single drive failure on a RAID10 that makes the entire array inaccessible, degraded I could understand but inaccessible?? I don't think the controller as prior to the reboot it was completely functional.

    Read the article

  • How to import .ops file in Outlook 2007

    - by r0ca
    Hi all, I install ORK.exe on my Windows 7 machine to create a copy of my profile so I will have it as a template to push it to new user. So basically, I ran the Profile Wizard to create an .ops file. I saved it in my documents for the moment. Right now, I'm trying to import that file into my Outlook but I just can't figure it out! My goal is to have a profile template to push to new users when they log in for first time. Thanks a bunch in advance! EDIT: I just figured it out. But I have a problem: When I create my profile, Outlook 2007 on exchange was not in cache mode. So I created my profile with the Profile Wizard with cache mode disabled. I save my outlook.ops in My documents. Then, I enabled cache mode so when I will import my .ops file, it should be restore as cache mode disabled... But When I do that, cache mode is still checked (which I don't want to) Am I doing something wrong? I guess so but I just can't figure it out

    Read the article

  • Cannot create a project TFS 2012 - TF218027

    - by GrandMasterFlush
    I've just installed TFS2012 and am trying to create a new project in the default collection via Visual Studio 2012 but I keep getting this error message: TF218027: The following reporting folder could not be created on the server that is running SQL Server Reporting Services: /TfsReports/DefaultCollection. The report server is located at: http://<servername>/Reports. The error is: The permissions granted to user '<domain>/grandmasterflush' are insufficient for performing this operation.. Verify that the path is correct and that you have sufficient permissions to create the folder on that server and then try again. I've checked the permissions and my user is a member of the Project Collection Administrators and the Project Collection Administrators group has the 'Create new project' permission set to allow. The only thing I think it might be is that the user that I created during installation for the Sharepoint access and reports viewing does not have permission to write to the reports folder, however if I select "Do not configure a SharePoint site at this time" then I still get the error messages. I can't find the reports folder to check the permissions either. TFS is using an instance of SQL 2012 that was already on the machine when TFS was installed. Can anyone see what I'm doing wrong please?

    Read the article

  • Unable to back up SQL Server databases using a maintenance plan

    - by Stephen Jennings
    I am trying to create a maintenance plan that will run automatically and back up my SQL Server 2005 databases automatically. I create a new maintenance plan and add a "Back Up Database Task", select all databases, and choose a path to back up to. When I save and try to execute this plan, I get the following error message: =================================== Execution failed. See the maintenance plan and SQL Server Agent job history logs for details. =================================== Job 'Backup.Subplan_1' failed. (SqlManagerUI) ------------------------------ Program Location: at Microsoft.SqlServer.Management.SqlManagerUI.MaintenancePlanMenu_Run.PerformActions() I've checked the maintenance plan log, the agent log, and just about every log file I can find and there are no entries at all to help me figure out why this is failing. If I right-click on a specific database and select "Back Up", the task succeeds. I tried changing the plan to back up just that one database and it still failed. I've tried running the plan with both Windows authentication and SQL Server authentication with the sa account. I also tried specifically granting the SQL Server Agent user account full privileges on the backup folder, but it still failed. While searching the web for clues, the only solution I've run across so far suggests running sp_configure 'allow_update', 0. I tried this but allow_update was already set to 0 and it did not fix the problem. The Windows server and SQL Server have all updates applied to them. Thanks for any suggestions!

    Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >