Search Results

Search found 51778 results on 2072 pages for 'super columns'.

Page 204/2072 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

  • Booting From VIA VT6421A Based PCI SATA Card

    - by Priyan R
    I bought a VIA VT6421A based SATA card for an 845 chipset based motherboard. The card is working i can access sata hdd from windows/linux. The problem is i can't directly boot from the sata card. My motherboard is award bios 6 based. I tried first boot as SCSI, its not worked. There is no Raid Bios screen appeared from the card. On searching i found , Add VT6421A bios to system bios as pci addon bios. I did it using cbrom6 , successfully added VT6421A bios to the existing bios. But now on booting instead of raid bios system bios showed Warning : something like cannot load add on rom for vendor id xxxx device id xxx . Whats wrong ? As the card is VT6421A based and i added VT6421A bios got from VIA website.

    Read the article

  • User Profile cannot be loaded - Windows 7

    - by Ryan
    After uninstalling an HP Vector Mouse driver, then rebooting, when Windows tries to auto log me in, i get an error message saying tyhe following: The User Profile Service failed the Login. User Profile cannot be loaded. Due to the fact that it is the only account on this PC, I cannot even go into another account. I rebooted the machine several times, before going into Safe Mode with Networking. For some reason, I cannot create a new account whilst in safe mode (I think it is to do with UAC, nothing with UAC is clickable). Thus, I am stuck. I cannot get into my account, nor can I create a new one to copy files over to. Any ideas? Thanks in advance! Ryan EDIT: System Restore was, for some reason turned off. Thus, I cannot restore to a working point.

    Read the article

  • Can I use this power supply + case combination without causing problems?

    - by evan
    I am putting together a computer with a Antec P180 case and a Thermaltake TR2 RX 650 W power supply. The problem is that the Antec P180 case has a separate compartment for the power supply. With an opening for the on/off switch + ac connector to one side, a wall with a small hole for cables to route through on top, a wall on the bottom, and on the other side a fan which pushes air from the hard drive compartment to the power supply compartment. I think the design of the case assumes the power supplies fan is on the side next to the on/off switch, but the fan on the power supply I have is on top, which makes me worry about overheating the power supply. There is about half an inch between the top of the power supply and the wall and the other fan should keep air flowing to push out the air that the power supply pushes upwards. Do you think this setup should work, or should I go get another power supply? Thanks!! PS: This computer will be running an Ubuntu server, so it will always be on, but the rest of the components shouldn't be generating as much heat as they would on say a gaming machine.

    Read the article

  • Performance variation

    - by Ree
    During my time spent working with multiple machines, I have noticed that performance of the same machine doing the same tasks in the same order differs and sometimes the difference is big enough to be noticeable. This applies to all the machines I've owned and/or maintained (old and modern). Some examples (many of them you may have noticed yourself) that sometimes are completed in different time frames: POST OS installation Hardware tests and operations (usually executed within a customized OS such as one of the many DOS variants), HDD tests and "low level" formats Software installation or other tasks (such as benchmarks) within a general purpose OS (Windows, Linux, etc) I can imagine this is caused by the fact that a machine is built with many components having to communicate as a whole and since the mechanical and electronic parts aren't perfect the overhead occurs. In the last example, I assume the OS complexity and concurrently running multiple processes has some additional effect as well. However, I'm wondering if this hardware imperfection and overhead is indeed that high to be humanly noticeable? Maybe there are other factors that are influencial as much or even more? So, in short - why? To emphasize: the difference is noticeable on the same machine performing the same tasks and this applies to ANY machine in my experience. I'm not comparing machine to machine performance.

    Read the article

  • Is there a way to make Apple Mail work well with Exchange server calendar?

    - by Joshua Frank
    My office uses Macs, but most of our clients use Windows and Outlook. Whenever people send invitations from Apple Mail to a Windows/Outlook machine, the invitations are garbled and look nothing like the nicely formatted invitations that Outlook people are used to. We also have no tools to view shared calendars, so we can choose mutually open time slots, and other useful calendar features that Outlook has and Apple Mail seems not to. So is there a plugin or third party program that will give Apple Mail the nice calendar features of Outlook? (By the way, I've looked into actually buying Outlook for Mac, and the pricing is kind of prohibitive, because you MUST buy the whole Office Suite, which we already have, there's no upgrade path, and there's no volume discounting.)

    Read the article

  • UDP multicast streaming of media content over WIFI

    - by sajad
    I am using vlc to stream media content over wireless network in scenario like this (from content streamer to stream receiver client): The bandwidth of wireless network is 54 Mb/s and UDP stream's required bandwidth is only 4 Mb/s; however there is trouble in receiving media stream and quality of playing specifically in multicast mode; means I can play the stream but it has jitter and does not play smoothly. In uni-cast I can stream up to 5 media streams correctly, but in multicast mode there is problem with streaming just one media! However when I stream from client some multicast streams; the wifi access-point can receive data correctly and I can see the video in "udp streamer" side correctly even when number of multicast streams increases to 9; But as you see I want to stream from streaming server and receive media in client size. Is this a typical problem of streaming real-time contents over wireless networks? Is it necessary to change configurations of my WIFI switch or it is just a software trouble? thank you

    Read the article

  • All downloads being interrupted

    - by Jake
    System: Windows 7 Professional 64bit. 8GB RAM, Intel i5-2400 CPU, +300GB free on the hard drive. AVG Internet Security 2012 (enabled & disabled, with firewall enabled and disabled - no effect for either). This computer is less than a year old. Network: This problem is occurring on a single computer on a network with multiple computers. The router is a Motorola Netopia 3347-02 (DSL Modem/Wireless Router combined). The computer is plugged in directly to the modem, other computers are using the wireless successfully. The router has been reset. The only thing odd about the connection between the router and computer is that it is configured to allow RDP through, so it is assigned a static IP by the router and port forwarding is enabled for port 3389. Also, though I doubt it matters, a second wireless router is active behind this router providing a second network that some computers in the area use without issues. Details: All downloads initiated on this specific computer eventually fail, this includes streaming from youtube, specialized downloads (itunes), downloads from websites, FTP downloads, etc. Failure occurs with all browsers, but in chrome this is the process it takes: 1) Download begins normally, 2) At some point between (observed) 7MBs and 229MBs the download stops progressing (at this point, if watching chrome's task manager, you can see the network activity for the downloading tab drop to 0kps), 3) for some time the download sits there still attempting to complete, but will eventually display "123,049,871/0 B, Interrupted" (where the number is whatever it actually got to). The file I am using to test this is a very large .zip file located on a server I control, but the problem seems to occur on any site. The amount downloaded is completely random, and seems to be more time-based than anything (if I start a download immediately after the last one fails, it tends to get further than the last one). Small files can get through for this reason, though they can fail as well. In a test where I simultaneously downloaded the same file via HTTP (chrome) and FTP (windows explorer), both downloads failed at the same instant, though explorer displayed "Connection timed out" several minutes before chrome finally showed the download as interrupted. Other things I have tried based on advice given to people with similar/identical problems: Setting my MTU to 1492 (as described here: http://blog.thecompwiz.com/2011/08/networking-issues.html) Disabling write caching to the hard drive storing the download on an external device successfully transmitted +1GB file from one computer on the same network to this computer disabling indexing in the folder the download was being stored in disabling all security software checked to make sure all drivers were up to date read about 50 accounts with nearly exact descriptions of what I'm experiencing, none of which had a solution given Running Processes: Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 104,836 K smss.exe 332 Services 0 1,276 K csrss.exe 764 Services 0 5,060 K wininit.exe 820 Services 0 4,748 K csrss.exe 844 Console 1 23,764 K services.exe 876 Services 0 11,856 K lsass.exe 892 Services 0 14,420 K lsm.exe 900 Services 0 7,820 K winlogon.exe 944 Console 1 7,716 K svchost.exe 428 Services 0 12,744 K svchost.exe 796 Services 0 12,240 K svchost.exe 1036 Services 0 22,372 K svchost.exe 1084 Services 0 174,132 K svchost.exe 1112 Services 0 56,144 K svchost.exe 1288 Services 0 18,640 K svchost.exe 1404 Services 0 29,616 K spoolsv.exe 1576 Services 0 25,924 K svchost.exe 1616 Services 0 12,788 K AppleMobileDeviceService. 1728 Services 0 9,796 K avgwdsvc.exe 1820 Services 0 8,268 K mDNSResponder.exe 1844 Services 0 5,832 K w3dbsmgr.exe 1108 Services 0 43,760 K QBCFMonitorService.exe 1336 Services 0 16,408 K svchost.exe 2404 Services 0 28,240 K taskhost.exe 3020 Console 1 12,372 K dwm.exe 2280 Console 1 5,968 K explorer.exe 2964 Console 1 152,476 K WUDFHost.exe 3316 Services 0 6,740 K svchost.exe 3408 Services 0 5,556 K RAVCpl64.exe 3684 Console 1 13,864 K igfxtray.exe 3700 Console 1 7,804 K hkcmd.exe 3772 Console 1 7,868 K igfxpers.exe 3788 Console 1 10,940 K sidebar.exe 3836 Console 1 84,400 K chrome.exe 3964 Console 1 19,640 K pptd40nt.exe 4068 Console 1 5,156 K acrotray.exe 3908 Console 1 14,676 K avgtray.exe 3872 Console 1 9,508 K jusched.exe 4076 Console 1 4,412 K iTunesHelper.exe 1532 Console 1 87,308 K SearchIndexer.exe 3492 Services 0 36,948 K iPodService.exe 4136 Services 0 7,944 K BrccMCtl.exe 4276 Console 1 18,132 K splwow64.exe 4380 Console 1 32,600 K qbupdate.exe 4836 Console 1 24,236 K svchost.exe 4288 Services 0 20,700 K wmpnetwk.exe 3112 Services 0 9,516 K FNPLicensingService.exe 5248 Services 0 5,852 K QBW32.EXE 5508 Console 1 127,068 K QBDBMgrN.exe 5600 Services 0 42,252 K EXCEL.EXE 2512 Console 1 99,100 K LMS.exe 3188 Services 0 5,616 K UNS.exe 1600 Services 0 7,308 K axlbridge.exe 5260 Console 1 5,132 K chrome.exe 5888 Console 1 200,336 K chrome.exe 3536 Console 1 26,076 K chrome.exe 1952 Console 1 20,168 K chrome.exe 4596 Console 1 24,696 K chrome.exe 4292 Console 1 48,096 K chrome.exe 2796 Console 1 23,520 K Acrobat.exe 1240 Console 1 87,252 K 123w.exe 4892 Console 1 22,728 K calc.exe 1700 Console 1 12,636 K chrome.exe 1328 Console 1 28,888 K chrome.exe 3696 Console 1 47,012 K rundll32.exe 6320 Console 1 7,104 K chrome.exe 4928 Console 1 44,248 K AVGIDSAgent.exe 260 Services 0 12,940 K avgfws.exe 6052 Services 0 26,912 K avgnsa.exe 5064 Services 0 2,496 K avgrsa.exe 3088 Services 0 2,200 K avgcsrva.exe 2596 Services 0 380 K avgcsrva.exe 6948 Services 0 408 K StikyNot.exe 452 Console 1 14,772 K chrome.exe 4580 Console 1 28,200 K chrome.exe 4016 Console 1 57,756 K svchost.exe 7140 Services 0 4,500 K chrome.exe 6264 Console 1 56,824 K chrome.exe 7008 Console 1 56,896 K chrome.exe 2224 Console 1 38,032 K taskhost.exe 612 Console 1 7,228 K chrome.exe 6000 Console 1 10,928 K chrome.exe 2568 Console 1 43,052 K chrome.exe 272 Console 1 75,988 K chrome.exe 7328 Console 1 53,240 K PaprPort.exe 7976 Console 1 137,152 K pplinks.exe 7500 Console 1 14,052 K ppscanmg.exe 5744 Console 1 18,996 K taskeng.exe 7388 Console 1 6,308 K SearchProtocolHost.exe 8024 Services 0 8,804 K SearchFilterHost.exe 7232 Services 0 7,848 K chrome.exe 8016 Console 1 37,440 K cmd.exe 7692 Console 1 3,096 K conhost.exe 7516 Console 1 5,872 K tasklist.exe 8160 Console 1 5,772 K WmiPrvSE.exe 7684 Services 0 6,400 K Any help with this would be greatly appreciated, I've been beating my head against a wall over this all day. This computer serves dual purpose as the main company document server and the Owner's work computer, it's fairly important it be fully functional and I cannot figure this out.

    Read the article

  • MSI Installer error 2203; how to force permissions on installer directory?

    - by goober
    [Cross-Posted on StackOverflow.com as well because the question relates to development. Feel free to let me know where it best belongs.] Hi all, I'll try to bullet-point to keep it short: Background / Issue Trying to install ASP.NET MVC 3 RC on my Windows 7 machine. Uninstalled other versions of MVC (2 and 3 Beta 1). Ran the installer -- got a generic error, 2203. Log files said that it was a permissions error on C:\Windows\Installer. Checked C:\Windows\Installer -- sure enough, it's marked as read-only. I un-checked "Read-Only" in the folder properties and applied. It appears to open the dialog and apply to all files. However, when clicking properties again, the read-only box is backed to checked. Checked the security tab of the folder -- both system and the Administrators group have full access. I checked ownership -- the Administrators group is listed as an owner. Verified that I'm in the system as an Administrator (in fact, the only account in the Administrators group besides Administrator). So, what gives? Thanks in advance for any help you can provide!

    Read the article

  • Windows 7 migration led to crashdump and hibernate problems

    - by MartyMacGyver
    Note: I'm using a Samsung 830 SSD (migrated OS from defunct PC) and other than these two (interrelated?) problems it's working fine. Surprisingly well actually. Motherboard is a ASUS P8Z77-V Deluxe. Problem 1: Crashdumps are not working. volmgr throws an event 45 "The system could not sucessfully load the crash dump driver." whenever you modify crashdump settings, or if a crashdump occurs. diskpart says that "Crashdump disk = no" which is peculiar. Problem 2: Hibernation isn't working. Again, volmgr throws the same event 45 if you try to hibernate. The screen blanks, then you're at the password prompt. No sleepage occurs. (Yes, I know I should avoid hibernation on SSDs but it's enabled and the hibernation file is definitely there so I'd like to know why it's failing). Diskpart claims "Hibernation file = no" which is again peculiar... it's plainly there and getting created by the system. The common factor appears to be volmgr and/or the crashdump "service" (if that's what it is). I'd much rather get this working than spend days reinstalling and reconfiguring the entire system, especially when it's working perfectly otherwise. Sleep works as well (as long as it's not hybrid sleep). So, what defines the flags "Crashdump disk" and "Hibernation file disk" in diskpart's output? And what might be going wrong that's breaking crashdumps in particular?

    Read the article

  • How to force high-dpi scaling?

    - by Ian Boyd
    How can i force an application to be high-dpi scaled? Or alternatively, how can an application that is not manifested as high-dpi aware, and doesn't have dpi-scaling disabled from the Properties-Compatibility tab, not be scaled? Pretend i have an application, who's developers decided to manifest it as high-dpi aware, when it really isn't. How can i force dpi-scaling? Pretend i have an applicaiton that Microsoft has applied the "HighDpiAware" compatiblity shim to, when the application really isn't. How can i force dpi-scaling? Pretend i have an application (i.e. Shareaza) that does not have a dpi-aware manifest, does not disable dpi-scaling from the application's Properties tab, but high-dpi scaling is not being applied? How can i force it? How can i force Windows to apply dpi-scaling to an application? See also

    Read the article

  • Base system driver error - HP Pavilion Entertainment PC dv9323cl

    - by Damurph
    I upgraded to Wndows 7 and have a problem with graphics with my NVIDIA GeoForce Go 7600 not displaying properly. Also the Base System Drivers have yellow flags near them and it states that the The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver. Any clues??? Please help!

    Read the article

  • Windows 8 unable to connect to WPA2 AES Wireless Network

    - by user170193
    I'm running Windows 8 and am unable to connect to my home wireless network. I've tried restarting the router, patching the drivers to the next version, patching the drivers to the last version, running windows update and patching the chipset drivers to the latest version. So far nothing has worked. My computer can get on the internet via USB tethering on my phone or an open WiFi connection, but it is unable to connect to my home WPA2 AES secured wireless network. It sees the network, attempts to connect, gets a limited connection and then drops the connection. All the other wireless devices in my household have no problems. I have the new Dell XPS 12, running Windows 8 using an Intel Centrino Advanced-N 6235 wireless adapter. I've refreshed windows twice now to try different driver configurations. I've tried uninstalling all the Dell software, I've tried uninstalling all the Intel software and reinstalling just the drivers. I've tried turning switching the ability for the Wireless driver to turn the computer off or on. I've tried setting up the connection manually from desktop mode. I've tried switching it on and off using the wireless button on the keyboard and in the software. So far nothing has allowed me to connect to the secured network. It just keeps getting a limited connection, dropping the connection and retrying. It's driving me crazy, any ideas, anything I missed? Thanks.

    Read the article

  • OS X not allowing me to rename a folder

    - by YGA
    Hi Folks, Can anyone thing of a reason why OS X would not allow me to do this? I seem to have total permissions... new-host-4:Desktop michael$ whoami michael new-host-4:Desktop michael$ ls -ltdr 2008_12_12/ drwxrwxrwx+ 5 michael wheel 170 Mar 28 18:23 2008_12_12/ new-host-4:Desktop michael$ mv 2008_12_12/ foo mv: rename 2008_12_12/ to foo: Permission denied new-host-4:Desktop michael$ Thanks! /YGA

    Read the article

  • Can't connect to LAN when connected to D-Link DIR-615

    - by Senseful
    I'm have a D-Link DIR-615 Wireless N 300 Router. I didn't use the CD it comes with to set up the network. Instead I configured it manually through the router's settings that are accessed via a web browser. The main changes I made are: Secured the router so that a password is required before clients can use the wireless internet. Broadcasting 802.11N only (not B or G). I can connect to the router just fine and I'm able to access the internet. The only problem is that I don't see any of the other computers in my LAN. When I try connecting to another Wi-Fi router that I have (which is connected to the same network), I can see all of the computer's on my LAN just fine. Therefore, I'm guessing that the reason I can't connect to the LAN is not a problem with my computer and is a problem with the router instead. I'm on a MacBook Air running Mac OS X 10.6.6. I tried contacting D-Link technical support, but they only try to help you if you have problems connecting to the internet. They aren't really concerned with problems that have to do with the accessing PC's on the same network.

    Read the article

  • Linux LiveCD (or LiveUSB) with custom xorg.conf

    - by Jakub Narebski
    Is there some Live Linux distribution (on CD, DVD or USB), which allow one to use specific xorg.conf file, i.e. specific X11 configuration? The problem I am trying to solve is to find Linux Live distribution for web browsing which would work well with NEC LCD 22WV monitor. It is supposedly DDCCCI capable, but X.Org X Window System autoconfiguration fails to detect proper modeline, and uses fallback 800x600 screen resolution, instead of preferred screen resolution of 1680x1050.

    Read the article

  • Why Does My Website Redirect me to my localhost?

    - by Noah Brainey
    Alight, my website has some issues that I'm not sure what's causing them. Visit this page http://online-file-sharing.net/tos.html and click one of the bottom footer links... it redirects you to your localhost in the address bar. I have no idea why it does this. I'm hosting this website on my own server, which is this computer, and using Xampp. If this information helps. Anyways any help would be greatly appreciated! I'm also using DYNDNS as my nameservers.

    Read the article

  • Dual monitors though 1 HDMI port

    - by Carlos
    I currently have a Dell Studio XPS 13 laptop connected to a 24" HP monitor (w2448hc). Im thinking on getting a second one, however am wondering what i need for the setup (hardware wise). Also I was wondering it there is any down side to it, or something i should be aware of. For example, image quality loss, GPU overloading, or anything important I should know. More than anything Im interested in your advice. Also the monitors do have built in speakers (HDMI sound output), is the sound going to be reproduced by only one monitor or both? Specs Model: Dell Studio XPS 13 OS: Genuine Windows® 7 Home Premium 64-Bit CPU: Intel® CoreTM 2 Duo P8600 (2.4GHz, 3MB L2 Cache, 1067MHz FSB) Chipset: NVIDIA® GeForce® MCP79MX RAM: 4GB 1067MHz DDR3 SDRAM Graphics: SLi NVIDIA® GeForce® 9500M - 256MB Thanks for your advice, if there is anything additional i need to buy an you have a personal preference pass the brand name so i can check it out. Thanks!

    Read the article

  • How to get Ruby support in Zend Studio?

    - by Andrew
    Zend Studio is basically Eclipse that has been optimized for working with Zend Framework projects. Well I have a few files in my Zend Framework project that happen to be Ruby files. Zend Studio doesn't come with the ability to create/edit Ruby files with syntax highlighting. I could open in the default text editor, but there won't be any syntax highlighting. How can I add support for Ruby files in Zend Studio?

    Read the article

  • change default username when ssh to another pc

    - by Tom
    When I ssh between different pcs I can omit my username (tom) and just type ssh pc_name instead of ssh tom@pc_name I like this feature, and have got into the habit of using it. Unfortunately, on one of my computers I went for the user name tommy. Everytime I connect to this computer I forget to write tommy@creative_pc and wonder why my password doesn't work. Is there a way to tell ssh what user name to use when the username is omitted? Edit: Just found the following question that is similar: How to make ssh log in as the right user? It didn't come up on my initial search.

    Read the article

  • Remote control a computer using another computer

    - by Dean
    I've got a main desktop computer at home, I'd like watch movies using it but able to control it afar. For example, I would like to lay on my bed and control the desktop using my own laptop via wireless. I've been looking for solutions to my question. I tried to use remote desktop, I can pause the movie but I then have to go to the pc to log in the OS again. I also tried to bind my desktop to my mobile phone over bluetooth, this works as I can control the mouse etc. but I found I can barely see the mouse pointer when at long distance. I still wish I can use my laptop as a remote control, is this possible?

    Read the article

  • Local area network computer to computer backup software

    - by thegreyspot
    Hi! I would like to back up my other computers on my local home network to my computer. What software would you suggest? I liked crashplan, however their confusing UI, and its ability not to sync, turned me away. But it has the right idea. A bonus would be if the software did not compile everything in to one file, but its ok if it does. Also I would like it to be free

    Read the article

  • How to stop SophosAV from scanning directories under source control

    - by user26453
    From googling it seems its well known that SophosAV as well as other AV programs have issues with how they interact and can inhibit source control utilities like TortoiseHG or TortoiseSVN. One solution is to exclude directories under source control from on-access scanning as detailed here on Sophos's support site. There is a corollary article that mentions some issues related to this, namely need to place multiple entries for exclusions based on the possibility of the location being accessed through the short vs. long name (e.g., Progra~1 vs. "Program Files"). One other twist is I am using a junction to relocate my user directory, C:\Users\Username, to a second hard drive, E:. Since I am not sure how this interacts I have included the source control directory as they are nested in both locations. As a result, I have included the two exclusions for the on-access scanning exclusions (and to be on the safe side on-demand exclusions as well, although this should only come into play when I select a parent directory of the exclusion to be scanned on-demand, but still). You'll notice I have no need to add extra exclusions for those locations based on short vs. long name distinctions. The two exclusion I have then, for both on-access and on-demand scanning exclusions are: C:\Users\Username\source-control-directory E:\source-control-directory However, this does not seem to work as TortoiseHG still lags terribly in response to any request as AV software starts scanning when the directory is accessed via TortoiseHG. I can verify without a doubt that Sophos is causing the problems: I can completely disable on-access scanning. Once this is done TortoiseHG responds very fast to all operations. I cannot leave this disabled obviously, but since the exclusion don't seem to be working, what next?

    Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >